Photocatalytic Activity of TiO_(2) Coatings Fabricated on Al_(2)O_(3) by Mechanical Coating Technique

The titanium coatings were prepared on Al_(2)O_(3) balls by mechanical coating technique (MCT),and then the coatings were oxidized to titanium oxides(TiO_(2)) films at 300-600 ℃.The effects of different milling time and oxidation temperature on thickness of films were studied.The composition and microstructure of the films were analyzed by scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS).The results show that the thickest coatings with an average thickness of 20 μm were obtained at the milling time of 15 h.In addition,with the increase of the oxidation temperature,the oxidation of the film is increased.When the milling time is 15 h,the oxidation temperature is 500 ℃,and the addition of photocatalyst is 1 g/mL.The films have the best photocatalytic performance when the degradation rate of methyl orange solution reaches the maximum value of 74.9 %,and the films have a good reusability.

Coating Protection for Production Facilities of Offshore Oil Fields

This paper describes coating protection of production facilities of offshore oil fields based on the practice of development of Bohai Offshore Oil Field, with focus laid on the selection of coating systems, surface preparation, coating application, as well as coating inspection for four types of major production facilities.

Effect of Spin Coating Speed on Some Optical Properties of ZnO Thin Films

This paper reports the synthesis and characterization of ZnO thin films prepared by sol-gel spin coating technique. The sol-gel was prepared from zinc acetate dehydrate as a precursor, 2-me- thoxyethanol as a solvent and di-ethanolamine as a stabilizer, and then deposited on glass substrate using spin coater at the coating speed of 1000 rpm, 2000 rpm, 3000 rpm, 4000 rpm, 5000 rpm and 6000 rpm. After pre-heated at 150℃, the samples were post-heated at 250oC and also annealed at 400℃. X-ray diffraction (XRD) of the films showed polycrystalline hexagonal structure, with (002) orientation as most intense peak having a grain size of 28.1 nm. The absorbance of the film decreases with increasing wavelength and the transmittance was generally high between visible regions from 280 nm - 1200 nm. The ZnO films deposited at a spinning speed of 2000 rpm had highest transmittance of 88% in the visible region from 280 nm - 1200 nm. The energy band gap was found to be in the range of 3.23 - 3.40 eV. The thicknesses of the films decreased with increase in coating speed. Based on these results, ZnO thin films obtained could have useful application in transparent conducting oxide electrode in solar cells.

Structural and optical properties of nano-spin coated sol-gel porous TiO_2 films

Three thicknesses of TiO2 films, 174, 195, and 229 nm, were deposited onto quartz substrates by sol–gel spin coating method. The as-deposited thin films were characterized by nano-crystallite with different sizes (19–46 nm) and relatively high porous structure. Optical constants were determined and showed the lowest refractive index of 1.66 for the as-prepared films that ever reported till now. Obtained results were discussed through current theoretical ideas.

Study on optical compound films

Using the compound materials and double e-gun evaporation,the compound optical films have been successfully deposited on K9 glass substrate.The refractive index of optical compund films deposited in diffeent parameters have been measured and theoretical formula for calculation refractive index of compound films have been derived.It is shown that the experimental curve for the variation of refractive index with wavelength in 0.4￣1.4 μm region and the theoretical one agree very well.Using these films,the laser reflecting mirror has been successfully coated.

Hydrogen Detection With FBG Sensor Technology for Disaster Prevention

Three fiber Bragg grating （FBG） sensors systems for hydrogen detection are presented using the classic Pd （palladium） coating technique （500nm） as the hydrogen sensitive film and titanium （Ti） as the adhesive layer with the etched cladding. These systems are compared and used for disaster environment prevention in hydrogen leakage environment where higher values than the normal are presented which increase the risk of explosion. With these systems, 0. 1% - 4% of the hydrogen volume concentration range in the volume ratio was detected and monitored experimentally in the test room with the very sensitive and stable value which reached 60pm/1% HE. In addition, a fast response time, about 6 s, was obtained with an advanced sensor.

GaInN light-emitting diodes with omni-directional reflector using nanoporous SnO_2 film

Enhancement of light extraction in a GaInN light-emitting diode （LED） employing an omni-directional reflector （ODR） consisting of GaN, SnO2 nanorod and an Ag layer was presented. The ODR comprises a transparent, quarterwave layer of SnO2 nanorod claded by silver and serves as an ohmic contact to p-type GaN. Transparent SnO2 sols were obtained by sol-gel method from SnCl2·2H2O, and SnO2 thin films were prepared by dip-coating technique. The average size of the spherical SnO2 particles obtained is 200 nm. The refractive index of the nanorod SnO2 film layer is 2.01. The GaInN LEDs with GaN/SnO2/Ag ODR show a lower forward voltage. This was attributed to the enhanced reflectivity of the ODR that employs the nanorod SnO2 film layer. Experimental results show that ODR-LEDs have lower optical losses and higher extraction efficiency as compared to conventional LEDs with Ni/Au contacts and conventional LEDs employing a distributed Bragg reflector （DBR）.