Value of Topology Approach to Diagnose of CAD Based on Magnetocardiographic Current Distribution Maps in Difficult-to-Diagnose Patients

Objective: The purpose of this work is to examine the usefulness of the topological approach for analysis of current density maps during ST-T interval in detection of coronary artery disease (CAD) in patients with proved CAD but normal results of routine tests. Materials and Methods: The patient group included 123 patients. Coronary angiography was done due to chest pain. The control group consisted of 124 healthy volunteers. The MCG test was done by 4-channels MCG system installed at unshielded setting. An integral topological index Kideal, consisting of 4 parameters, has been counted. Results and Conclusions: It is shown that Kideal was higher in patient group compared to control one. Sensitivity was 87%, and specificity was 64%. The topological analysis of MCG current density maps is a valuable tool in noninvasive detection of CAD in difficult-to-diagnose patients with uninformative results of routine tests.

Single-phase earth fault current distribution between optical fiber composite overhead ground wire and ordinary ground wire in transmission system

It is important for the safety of transmission system to accurately calculate single-phase earth fault current distribution.Features of double sided elimination method were illustrated.Quantitative calculation of single-phase earth fault current distribution and case verification were accomplished by using the loop method.Influences of some factors,such as single-phase earth fault location and ground resistance of poles,on short-circuit current distribution were discussed.Results show that:1) results of the loop method conform to those of double sided elimination method;2) the fault location hardly influences macro-distribution of short-circuit current.However,current near fault location is evidently influenced;and 3) the short-circuit current distribution is not so sensitive to the ground resistance of poles.

Input Admittance and Current Distribution of Infinitely Long Circular Cylindrical Antenna Driven at Center

In this paper, by change of integration path in complex spectrum domain and by defining input admittance as the ratio of complex radiated power to amplitude of square of voltage across the gap, new expressions of admittance (valid for all frequencies ) of infinitely long cylindrical antenna with and without conducting ground are obtained. Meanwhile corresponding formulas of current distribution are derived in detail. Some numerical computations are also given.

Dependence of Switching Current Distribution of a Current-Biased Josephson Junction on Microwave Frequency

We investigate the distribution of the switching current of a current-biased Josephson junction （CBJJ） and its dependence on the microwave frequency using two theoretical methods, one of which is the quantum trajectory method and the other is the master equation method. Both the methods show that the distribution of the switching current of CBJJ will exhibit double peaks in a certain range of microwave frequency if proper microwave power is given, and the gap between the two peaks will increase with the microwave frequency. The obtained results can be used to identify the energy difference of the ground and first excited states in a Josephson junction for any bias current.

Numerical Simulation of Current Density Distribution in Keyhole Double-Sided Arc Welding

In the double-sided arc welding system (DSAW) composing of PAW+TIG arcs, the PAW arc is guided by the TIG arc so that the current mostly flows through the direction of the workpiece thickness and the penetration is greatly improved. To analyze the current density distribution in DSAW is beneficial to understanding of this process. Considering all kinds of dynamic factors acting on the weldpool, this paper discusses firstly the surface deformation of the weldpool and the keyhole formation in PAW+TIG DSAW process on the basis of the magnetohydrodynamic theory and variation principles. Hence, a model of the current density distribution is developed. Through numerical simulation, the current density distribution in PAW+TIG DSAW process is quantitatively analyzed. It shows that the minimal radius of keyhole formed in PAW+TIG DSAW process is 0.5 mm and 89.5 percent of current flows through the keyhole.

Plating current density distribution of lithium metal anodes in pouch cells

The uniformity of current density distribution upon electrodes is one of the most important factors determining the lithium dendrites growth and cycling performance of lithium metal batteries(LMBs). Herein,current density distributions of lithium metal anodes induced by various engineering factors, consisting of uneven cathode, electrolyte distribution, and different tab positions, and their effects on the electrochemical performance are investigated theoretically and experimentally in pouch cells. The deviation of current density in lithium metal anodes ranges from 2.47% to 196.18% due to the different levels of uneven cathode materials. However, the deviation is just 13.60% for different electrolyte thicknesses between cathodes and anodes, even a ten-layer separator in some positions. The maximum deviation for variational tab positions is only 0.17%. The nonuniformity in current density distribution results in severe dendrite growth issues and poor electrochemical performance of LMBs. This work not only confirms the direct correlation between the uneven current density distribution and lithium deposition behaviors, but also points out the decisive effects of cathode surface roughness on current distribution of anodes, to which more attentions should be paid in practical applications of LMBs.

Spatial Distribution Characteristics of Surface Tidal Currents in the Southwest of Taiwan Strait

This study was conducted on the spatial distribution characteristics of surface tidal currents in the southwestern Taiwan Strait based on the quasi-harmonic analysis of current data obtained by two high frequency surface wave radar(HFSWR) systems. The analysis shows that the tidal current pattern in the southwestern Taiwan Strait is primarily semi-diurnal and influenced significantly by shallow water constituents. The spatial distribution of tidal current ellipses of M2 is probably affected by the interaction between two different systems of tide wave, one from the northern mouth of Taiwan Strait and the other from the Bashi Channel. The directions of the major axes of M2 tidal current ellipses coincide roughly with the axis of the Taiwan Strait. The spatial distribution of the magnitudes of the probable maximum current velocity(PMCS) shows gradual increase of the velocity from northeast to southwest, which is in accordance with the spatial distribution of the measured maximum current velocity(MMCS). The directions of the residual currents are in accordance with the direction of the prevailing monsoon wind at the Taiwan Strait and the direction of the Taiwan warm current during summer. The bathymetry also shows a significant effect on the spatial distribution characteristics of tidal currents.

A study of pulsed high voltage driven hollow-cathode electron beam sources through synchronous optical trigger

In this study,a pulsed,high voltage driven hollow-cathode electron beam sources through an optical trigger is designed with characteristics of simple structure,low cost,and easy triggering.To validate the new design,the characteristics of hollow-cathode discharge and electron beam characterization under pulsed high voltage drive are studied experimentally and discussed by discharge characteristics and analyses of waveform details,respectively.The validation experiments indicate that the pulsed high voltage supply significantly improves the frequency and stability of the discharge,which provides a new solution for the realization of a high-frequency,high-energy electron beam source.The peak current amplitude in the high-energy electron beam increases from 6.2 A to 79.6 A,which indicates the pulsed power mode significantly improves the electron beam performance.Besides,increasing the capacitance significantly affects the highcurrent,lower-energy electron beam more than the high-energy electron beam.

新能源大基地风光储容量协调优化配置

大型新能源基地需要协调配置风光火储容量以满足外送要求,其中火电容量及外送通道的容量通常预先确定,从而风电、光伏、储能的容量配置成为影响新能源外送效果的重要因素。为此,针对大型新能源基地,研究了风光储容量优化配置问题,提出了基于新能源外送可靠性的容量配置方法。基于需求侧的负荷曲线,提出了一种聚类方法来优化直流通道的计划传输功率;基于直流计划功率,提出了衡量新能源外送可靠性的送电置信概率指标;基于送电置信概率等约束,构建了风光储容量优化配置的基本规划模型。为了进一步保证在不同的场景下新能源能可靠外送,在基本规划模型的基础上加入场景分布不确定性,提出了风光储容量配置的分布鲁棒规划模型。考虑到分布鲁棒约束包含整数变量,提出了一种迭代算法用于该分布鲁棒规划模型的求解。实际算例验证了所提方法的有效性。

考虑线路动态电热特性的交直流系统分布鲁棒潮流优化策略

为了充分发挥交直流线路耐热特性、提高系统在不确定运行环境下应对故障的调控能力,以含柔性直流输电技术(VSC-HVDC)的交直流系统为研究对象,提出一种考虑线路动态电热特性的分布鲁棒潮流优化策略。首先,根据热传导理论分别建立交流架空线路、直流电缆线路的动态电热模型,而后在校正控制中引入交、直流输电线路短期最高允许温度(SAOT)约束及校正期间最大热积累量来代替长期允许温度(LAOT)作为在校正期间的暂时安全约束,以达到充分利用线路的短期过载/耐热特性的目的;其次,将故障后的校正过程划分成两个子校正过程,通过最大化储能及VSC-HVDC的快速校正能力,弥补常规调控装置难以快速响应指令的缺陷,进一步,在基于Kullback-Leibler(KL)散度所构建的风荷概率分布模糊集上,通过在考虑风荷最恶劣概率分布的情况下进行潮流优化,改善了传统鲁棒优化方法过于保守的问题;再次,在列和约束生成(C&CG)算法和Multi-cut Benders分解算法的基础上,提出一种融合物理知识的双循环分解算法,不仅能避免对非过载线路热平衡方程的线性化,同时还能避免多场景多故障协同求解;最后,在基于改进的IEEE 39测试系统中对所提模型及算法的有效性进行了验证。

Numerical simulation and experimental validation of a direct current air corona discharge under atmospheric pressure

Air corona discharge is one of the critical problems associated with high-voltage equipment. Investigating the corona mechanism plays a key role in enhancing the electrical insulation performance. An improved self-consistent multi-component two-dimensional plasma hybrid model is presented for the simulation of a direct current atmospheric pressure corona discharge in air. The model is based on plasma hydrodynamic and chemical models, and includes 12 species and 26 reactions. In addition, the photoionization effect is introduced into the model. The simulation on a bar-plate electrode configuration with an inter-electrode gap of 5.0 mm is carried out. The discharge voltage- current characteristics and the current density distribution predicted by the hybrid model agree with the experimental measurements. In addition, the dynamics of volume charged species generation, discharge current waveform, current density distribution at an electrode, charge density, electron temperature, and electric field variations are investigated in detail based on the model. The results indicate that the model can contribute valuable insights into the physics of an air plasma discharge.

Analytical solutions for transverse distributions of stream-wise velocity in turbulent flow in rectangular channel with partial vegetation

The theory of poroelasticity is introduced to study the hydraulic properties of the steady uniform turbulent flow in a partially vegetated rectangular channel. Plants are assumed as immovable media. The resistance caused by vegetation is expressed by the theory of poroelasticity. Considering the influence of a secondary flow, the momentum equation can be simplified. The momentum equation is nondimensionalized to obtain a smooth solution for the lateral distribution of the longitudinal velocity. To verify the model, an acoustic Doppler velocimeter （ADV） is used to measure the velocity field in a rectangular open channel partially with emergent artificial rigid vegetation. Comparisons between the measured data and the computed results show that the method can predict the transverse distributions of stream-wise velocities in turbulent flows in a rectangular channel with partial vegetation.

Electrical characteristics of new three-phase traction power supply system for rail transit

A novel three-phase traction power supply system is proposed to eliminate the adverse effects caused by electric phase separation in catenary and accomplish a unifying manner of traction power supply for rail transit.With the application of two-stage three-phase continuous power supply structure,the electrical characteristics exhibit new features differing from the existing traction system.In this work,the principle for voltage levels determining two-stage network is dissected in accordance with the requirements of traction network and electric locomotive.The equivalent model of three-phase traction system is built for deducing the formula of current distribution and voltage losses.Based on the chain network model of the traction network,a simulation model is established to analyze the electrical characteristics such as traction current distribution,voltage losses,system equivalent impedance,voltage distribution,voltage unbalance and regenerative energy utilization.In a few words,quite a lot traction current of about 99%is undertaken by long-section cable network.The proportion of system voltage losses is small attributed to the two-stage three-phase power supply structure,and the voltage unbal-ance caused by impedance asymmetry of traction network is less than 1‰.In addition,the utilization rate of regenerative energy for locomotive achieves a significant promotion of over 97%.

Development and Implementation of GSM-Based Distribution Automation System with Graphic User Interface in Nigeria Electric Power Distribution Network

Lack of up-to-date information on efficient operation and maintenance of EPDS （electric power distribution systems）, Nigeria is addressed by designing and implementing an indigenous real-time monitoring and diagnosis system. The system encompasses the development of software driven hardware positioned at the remotely located sub-stations at the low voltage level to keep track of the network in real-time. The detection of faults exploits threshold passing algorithm through continuous monitoring of the network power quality. Communication between the RTU （remote terminal unit） and the DCC （distribution control center） which is based on GSM is initiated by disturbance. The DCC performs fault evaluation processing using the received data and predetermined faults signatures to determine the nature of disturbance and presents the result in graphic user interface environment. A fault reporting time of 2 s was achieved. The developed system exhibits a high degree of accuracy and manifests no spurious reports during testing. The resultant system limits the effects of interruption and increases power availability by reducing the down time. The system strengthens engineering and management capabilities required to enhance reliability by providing information about the network health status.

全绝缘自支撑电缆系统设计(英文)

All-dielectric self-supporting(ADSS) cables are installed along with transmission line for the purpose of communication.During installation the outer layer of the cable is hydrophobic and is not prone to dry band arcing. These cables become less hydrophobic over time and become vulnerable to dry band arcing.This loss in hydrophobicity is because of the contamination formed on the outer layer due to pollution.This is one of the reasons which cause cable failure.Considerable amount of losses will be incurred on the occurrence of a cable failure as the cables are also leased to other companies.An improved equivalent circuit is used to calculate the voltage and current distribution of the double circuit line.A three-phase single circuit line and a three-phase double circuit line are used to calculate their corresponding voltage distribution and current distribution.The results could be used to predict dry band arcing on similar models.The method used considers sag,span and pollution on ADSS cable.

Evaluation of 1-kW Class PEM Fuel Cell Stack under In-Situ Conditions Considering Individual Cells

Focusing on the stack performance is important for practical use of PEM （proton exchange membrane） fuel cells. This paper describes the experiments and evaluation on the performance of 1-kW class PEM FC （fuel cell） stacks for reliability improvement. We investigated the stack performance, voltage distributions, and internal resistance of the single cells of a PEMFC stack. The standard deviation of individual cell voltages increased almost linearly with the current load by 2.5 times that in the case of an open-circuit voltage, with a standard deviation of 33 A. From the results of the current-interrupt tests, the internal resistance of the FC stack was calculated to be 43.53 mΩ. The internal resistances of each individual cell were not uniform. The average internal resistance was 0.505 mΩ at 18 A, which was less than that calculated from the stack current-interrupt test. We also investigated the current distribution in the PEM FC stack under in-situ conditions using a triaxial magnetic sensor probe. From the results, the current distribution tended to concentrate on the underside of the cell. Each I-V curve at the divided plane can be obtained using the developed method.

Structural Parameter Optimization of Multilayer Conductors in HTS Cable

In this paper, the design optimization of the structural parameters of multilayer conductors in high temperature superconducting （HTS） cable is reviewed. Various optimization methods, such as the particle swarm optimization （PSO）, the genetic algorithm （GA）, and a robust optimization method based on design for six sigma （DFSS）, have been applied to realize uniform current distribution among the multilayer HTS conductors. The continuous and discrete variables, such as the winding angle, radius, and winding direction of each layer, are chosen as the design parameters. Under the constraints of the mechanical properties and critical current, PSO is proven to be a more powerful tool than GA for structural parameter optimization, and DFSS can not only achieve a uniform current distribution, but also improve significantly the reliability and robustness of the HTS cable quality.

Electronic transmission of three-terminal pyrene molecular bridge

This paper investigates theoretically the electronic transmission spectra of the three terminal pyrene molecular bridge and the quantum current distribution on each bond by the tight-binding model based on nonequilibrium Green＇s function and the quantum current density approach, in which one π molecular orbital is taken into account per carbon atom when the energy levels and HOMO-LUMO gap are obtained. The transmission spectra show that the electronic transmission of the three terminal pyrene molecular bridge depends obviously on the incident electronic energy and the pyrene eigenenergy. The symmetrical and oscillation properties of the transmission spectra are illustrated. A novel plus-minus energy switching function is found. The quantum current distribution shows that the loop currents inside the pyrene are induced, and some bond currents are much larger than the input and the output currents. The reasons why the loop currents and the larger bond currents are induced are the phase difference of the atomic orbits and the degeneracy of the molecular orbits. The calculations illustrate that the quantum current distributions are in good agreement with Kirchhoff quantum current conservation law.

Typical application of Rogowski coils in inspection of electrobath

During the aluminum electrolytic roasting process,each component of the electrobath of aluminum performs unsteadily when the electrolytic bath is in the pre-roasting stage. It is important to monitor the currents of the anodes and the cathodes of the aluminum electrobath at regular intervals. Both practice and investigation indicate that Rogowski coil can be adopted to measure heavy direct current of the anodes and the cathodes of the aluminum electrobath. The paper not only introduces the typical application of the Rogowski coil to inspect the state of aluminum electrobath in the roasting process, but also analyzes the principles of the coil sensor including its dynamic properties and some important measurement results respectively. The optimal parameters of the coil can be simulated by means of an advanced simulation tool: simulink tools based on MATLAB soft environment. Based on the gathered current data, an even-current coefficient has been introduced, and the current curve can be drawn. Since they are applied in AL-Electrolyzing, it is possible to distinguish the anode of which the current is not evenly distributed, and to take adjusting measures over a period of time to ensure that the current is evenly distributed.

Effects of mask wall angle on matrix-hole shape changes during electrochemical machining by mask

The influences of the mask wall angle on the current density distribution,shape of the evolving cavity and machining accuracy were investigated in electrochemical machining(ECM) by mask.A mathematical model was developed to predict the shape evolution during the ECM by mask.The current density distribution is sensitive to mask wall angle.The evolution of cavity is determined by the current density distribution of evolving workpiece surface.The maximum depth is away from the center of holes machined,which leads to the island appearing at the center of cavity for mask wall angles greater than or equal to 90°(β≥90°).The experimental system was established and the simulation results were experimentally verified.The results indicate that the simulation results of cavity shape are consistent with the actual ones.The experiments also show that the repetition accuracy of matrix-hole for β≥90° is higher than that for β<90°.A hole taper is diminished,and the machining accuracy is improved with the mask wall angle increasing.