基于模块化多电平换流器的高压柔性直流输电系统(modular multilevel converter-based high voltage direct current,MMC-HVDC)常采用双极接线方式以提高系统功率输送能力和可靠性。然而目前对于风电场经柔直外送系统的稳定性研究集中...基于模块化多电平换流器的高压柔性直流输电系统(modular multilevel converter-based high voltage direct current,MMC-HVDC)常采用双极接线方式以提高系统功率输送能力和可靠性。然而目前对于风电场经柔直外送系统的稳定性研究集中于单极接线方式,孤岛直驱风电场与采用不同双极协调控制的双极MMC-HVDC互联系统小信号稳定性问题还有待进一步探究。该文首先考虑频率耦合特性、参考系初相位和直流侧耦合特性的影响,分别建立了采用双U/f下垂控制和定U/f-P/Q控制的双极MMC-HVDC系统交流侧等效SISO阻抗模型,并详细分析了金属回线阻抗和双极间功率均分度对交流阻抗特性的影响。接着对比研究了两种协调控制中共有控制环路和特有控制环路对交流侧负电阻特性及互联系统稳定性的影响规律。最后,孤岛直驱风电场经两种双极协调控制下双极MMC-HVDC外送系统Matlab/Simulink时域仿真结果和硬件在环半实物实时仿真实验结果验证了所提出的小信号阻抗模型的精确性和稳定性分析结论的有效性。展开更多
A mine-used multi-function serial signal converter is introduced.This converter is based on Ethernet.The core of this design is embedded microprocessor STM32F107VCT6.Embedded operation system μC/OS-Ⅱ is transplanted...A mine-used multi-function serial signal converter is introduced.This converter is based on Ethernet.The core of this design is embedded microprocessor STM32F107VCT6.Embedded operation system μC/OS-Ⅱ is transplanted into this converter,and light-weight Internet protocal （LwIP） stack is also embedded to realize mutual conversion of serial signals such as meter bus （M-Bus） signal,RS485 signal,RS232 signal and Ethernet signal.Interconnection between all kinds of monitoring system interfaces under coal mine can be formed easily,which can solve compatibility problem between monitoring system and communication system and improve overall performance of safety monitoring system.The designed multi-function serial signal converter is of great value for application,which is worthy to be popularized in coal mine safety production.展开更多
In this study, organic solar cells (OSCs) with an active layer, a blend of polymer of non-fullerene (NFA) Y6 as an acceptor, and donor PBDB-T-2F as donor were simulated through the one-dimensional solar capacitance si...In this study, organic solar cells (OSCs) with an active layer, a blend of polymer of non-fullerene (NFA) Y6 as an acceptor, and donor PBDB-T-2F as donor were simulated through the one-dimensional solar capacitance simulator (SCAPS-1D) software to examine the performance of this type of organic polymer thin-film solar cell by varying the thickness of the active layer. PFN-Br interfacial layer entrenched in OPV devices gives overall enhanced open-circuit voltage, short-circuit current density and fill factor thus improving device performance. PEDOT: PSS is an electro-conductive polymer solution that has been extensively utilized in solar cell devices as a hole transport layer (HTL) due to its strong hole affinity, good thermal and mechanical stability, high work function, and high transparency in the visible range. The structure of the organic solar cell is ITO/PEDOT: PSS/BTP-4F: PBDB-T-2F/PFN-Br/Ag. Firstly, the active layer thickness was optimized to 100 nm;after that, the active-layer thickness was varied up to 900 nm. The results of these simulations demonstrated that the active layer thickness improves efficiency significantly up to 500 nm, then it decreased with increasing the thickness of the active layer from 600 nm, also notice that the short circuit current and the fill factor decrease with increasing the active layer from 600 nm, while the open voltage circuit increased with increasing the thickness of the active layer. The optimum thickness is 500 nm.展开更多
Based on the renormalization group theory, a hydraulic torque converter 3 D turbulent single flow passage model is constructed and boundary condition is determined for analyzing the influence of the fluid field chara...Based on the renormalization group theory, a hydraulic torque converter 3 D turbulent single flow passage model is constructed and boundary condition is determined for analyzing the influence of the fluid field characteristic and parameters on the macroscopic model. Numerical simulation of the single fluid path is processed by computational fluid dynamics and the calculated results approach to experimental data well, and especially in low transmission ratio the torque and head results are more close to experimental data than the calculated results of beam theory. This shows that the appropriate ternary analysis method and reasonable assumption of boundary condition may analyze the flow field more precisely and predict the performance of torque converter more accurately.展开更多
This paper presents a 2GS/s 10bit CMOS digital-to-analog converter （DAC） that consists of two unit current-cell matrixes for 6MSBs and 4LSBs, respectively, trading off between the precision and size of the chip. Cur...This paper presents a 2GS/s 10bit CMOS digital-to-analog converter （DAC） that consists of two unit current-cell matrixes for 6MSBs and 4LSBs, respectively, trading off between the precision and size of the chip. Current mode logic （CML） is used to ensure high speed,and a double centro-symmetric current matrix is designed by the Q^2 random walk strategy in order to ensure the linearity of the DAC. The DAC occupies 2.2mm × 2.2mm of die area and consumes 790mW with a single 3.3V power supply.展开更多
A methodology for performance optimization of torque converters is put forward based on the one-dimensional (1D) flow model. It is found that the inaccuracy of 1D flow model for predicting hydraulic performance at the...A methodology for performance optimization of torque converters is put forward based on the one-dimensional (1D) flow model. It is found that the inaccuracy of 1D flow model for predicting hydraulic performance at the low speed ratio is mainly caused by the separation phenomenon at the stator cascade which is induced by large flow impinging at the pressure side of the stator blades. A semi-empirical separation model is presented and incorporated to the original 1D flow model. It is illustrated that the improved model is able to predict the circumferential velocity components accurately, which can be applied to performance optimization. Then, the Pareto front is obtained by using the genetic algorithm (GA) in order to inspect the coupled relationship among stalling impeller torque capacity, stalling torque ratio and efficiency. The efficiency is maximized on the premise that a target stalling impeller torque capacity and torque ratio are achieved. Finally, the optimized result is verified by the computational fluid dynamics(CFD) simulation, which indicates that the maximal efficiency is increased by 0.96%.展开更多
A flexible flat torque converter was proposed to fulfill the requirement of miniaturization and power density maximization for automobiles.Constructed by two arcs joined by lines,the torus was designed directly from d...A flexible flat torque converter was proposed to fulfill the requirement of miniaturization and power density maximization for automobiles.Constructed by two arcs joined by lines,the torus was designed directly from design path.The influence of flatness on the performance of the torque converter was evaluated.The software CFX and standard k-ε model were adopted to simulate the internal flow fields of the torque converter under different flatness ratios.The results indicated that the performance of the torque converter got worse as the flatness declined,but the capacity of pump increased.The efficiency and the torque ratio dropped slightly as the flatness ratio decreased.So the torque converter could be squashed appropriately to get high power density without too much efficiency sacrifice.But when the flatness ratio was below 0.2,there was a significant drop in the efficiency.展开更多
The manufacturing of spiral groove structure of two-dimensional valve(2D valve)feedback mechanism has shortcomings of both high cost and time-consuming.This paper presents a novel configuration of rotary electro-mecha...The manufacturing of spiral groove structure of two-dimensional valve(2D valve)feedback mechanism has shortcomings of both high cost and time-consuming.This paper presents a novel configuration of rotary electro-mechanical converter with negative feedback mechanism(REMC-NFM)in order to replace the feedback mechanism of spiral groove and thus reduce cost of valve manufacturing.In order to rapidly and quantitative evaluate the driving and feedback performance of the REMC-NFM,an analytical model taking leakage flux,edge effect and permeability nonlinearity into account is formulated based on the equivalent magnetic circuit approach.Then the model is properly simplified in order to obtain the optimal pitch angle.FEM simulation is used to study the influence of crucial parameters on the performance of REMC-NFM.A prototype of REMC-NFM is designed and machined,and an exclusive experimental platform is built.The torque-angle characteristics,torque-displacement characteristics,and magnetic flux density in the working air gap with different excitation currents are measured.The experimental results are in good agreement with the analytical and FEM simulated results,which verifies the correctness of the analytical model.For torque-angle characteristics,the overall torque increases with both current and rotation angle,which reaches about 0.48 N·m with 1.5 A and 1.5°.While for torque-displacement characteristics,the overall torque increases with current yet decrease with armature displacement due to the negative feedback mechanism,which is about 0.16 N·m with 1.5 A and 0.8 mm.Besides,experimental results of conventional torque motor are compared with counterparts of REMC-NFM in order to validate the simplified model.The research indicates that the REMC-NFM can be potentially used as the electro-mechanical converter for 2D valves in civil servo areas.展开更多
This text has expounded the working principle of realizing A/D conversion that utilizes the timer within MCU and combinesthe technology of PWM. The design of hardware circuit, improved gradual approached trial arithme...This text has expounded the working principle of realizing A/D conversion that utilizes the timer within MCU and combinesthe technology of PWM. The design of hardware circuit, improved gradual approached trial arithmetic and relevant program design arediscussed in detail. And it has analyzed the resolution of A/D converter based on the technology of PWM, etc.展开更多
The proposed DAC consists of a unit current-cell matrix for 8MSBs and a binary-weighted array for 4LSBs,trading-off between the precision,speed,and size of the chip.In order to ensure the linearity of the DAC,a double...The proposed DAC consists of a unit current-cell matrix for 8MSBs and a binary-weighted array for 4LSBs,trading-off between the precision,speed,and size of the chip.In order to ensure the linearity of the DAC,a double Centro symmetric current matrix is designed by the Q2 random walk strategy.To achieve better dynamic performance,a latch is added in front of the current switch to change the input signal,such as its optimal cross-point and voltage level.For a 12bit resolution,the converter reaches an update rate of 300MHz.展开更多
A 16 bit stereo audio novel stability fifth-order ∑△ A/D converter that consists of switched capacitor ∑△ modulators, a decimation filter, and a bandgap circuit is proposed. A method for the stabilization of a hig...A 16 bit stereo audio novel stability fifth-order ∑△ A/D converter that consists of switched capacitor ∑△ modulators, a decimation filter, and a bandgap circuit is proposed. A method for the stabilization of a high order single stage ∑△ modulator is also proposed. A new multistage comb filter is used for the front end decimation filter. The ∑△ A/D converter achieves a peak SNR of 96dB and a dynamic range of 96dB. The ADC was implemented in 0. 5μm 5V CMOS technology. The chip die area occupies only 4. 1mm × 2.4mm and dissipates 90mW.展开更多
文摘基于模块化多电平换流器的高压柔性直流输电系统(modular multilevel converter-based high voltage direct current,MMC-HVDC)常采用双极接线方式以提高系统功率输送能力和可靠性。然而目前对于风电场经柔直外送系统的稳定性研究集中于单极接线方式,孤岛直驱风电场与采用不同双极协调控制的双极MMC-HVDC互联系统小信号稳定性问题还有待进一步探究。该文首先考虑频率耦合特性、参考系初相位和直流侧耦合特性的影响,分别建立了采用双U/f下垂控制和定U/f-P/Q控制的双极MMC-HVDC系统交流侧等效SISO阻抗模型,并详细分析了金属回线阻抗和双极间功率均分度对交流阻抗特性的影响。接着对比研究了两种协调控制中共有控制环路和特有控制环路对交流侧负电阻特性及互联系统稳定性的影响规律。最后,孤岛直驱风电场经两种双极协调控制下双极MMC-HVDC外送系统Matlab/Simulink时域仿真结果和硬件在环半实物实时仿真实验结果验证了所提出的小信号阻抗模型的精确性和稳定性分析结论的有效性。
文摘A mine-used multi-function serial signal converter is introduced.This converter is based on Ethernet.The core of this design is embedded microprocessor STM32F107VCT6.Embedded operation system μC/OS-Ⅱ is transplanted into this converter,and light-weight Internet protocal （LwIP） stack is also embedded to realize mutual conversion of serial signals such as meter bus （M-Bus） signal,RS485 signal,RS232 signal and Ethernet signal.Interconnection between all kinds of monitoring system interfaces under coal mine can be formed easily,which can solve compatibility problem between monitoring system and communication system and improve overall performance of safety monitoring system.The designed multi-function serial signal converter is of great value for application,which is worthy to be popularized in coal mine safety production.
文摘In this study, organic solar cells (OSCs) with an active layer, a blend of polymer of non-fullerene (NFA) Y6 as an acceptor, and donor PBDB-T-2F as donor were simulated through the one-dimensional solar capacitance simulator (SCAPS-1D) software to examine the performance of this type of organic polymer thin-film solar cell by varying the thickness of the active layer. PFN-Br interfacial layer entrenched in OPV devices gives overall enhanced open-circuit voltage, short-circuit current density and fill factor thus improving device performance. PEDOT: PSS is an electro-conductive polymer solution that has been extensively utilized in solar cell devices as a hole transport layer (HTL) due to its strong hole affinity, good thermal and mechanical stability, high work function, and high transparency in the visible range. The structure of the organic solar cell is ITO/PEDOT: PSS/BTP-4F: PBDB-T-2F/PFN-Br/Ag. Firstly, the active layer thickness was optimized to 100 nm;after that, the active-layer thickness was varied up to 900 nm. The results of these simulations demonstrated that the active layer thickness improves efficiency significantly up to 500 nm, then it decreased with increasing the thickness of the active layer from 600 nm, also notice that the short circuit current and the fill factor decrease with increasing the active layer from 600 nm, while the open voltage circuit increased with increasing the thickness of the active layer. The optimum thickness is 500 nm.
文摘Based on the renormalization group theory, a hydraulic torque converter 3 D turbulent single flow passage model is constructed and boundary condition is determined for analyzing the influence of the fluid field characteristic and parameters on the macroscopic model. Numerical simulation of the single fluid path is processed by computational fluid dynamics and the calculated results approach to experimental data well, and especially in low transmission ratio the torque and head results are more close to experimental data than the calculated results of beam theory. This shows that the appropriate ternary analysis method and reasonable assumption of boundary condition may analyze the flow field more precisely and predict the performance of torque converter more accurately.
文摘This paper presents a 2GS/s 10bit CMOS digital-to-analog converter （DAC） that consists of two unit current-cell matrixes for 6MSBs and 4LSBs, respectively, trading off between the precision and size of the chip. Current mode logic （CML） is used to ensure high speed,and a double centro-symmetric current matrix is designed by the Q^2 random walk strategy in order to ensure the linearity of the DAC. The DAC occupies 2.2mm × 2.2mm of die area and consumes 790mW with a single 3.3V power supply.
基金National Natural Science Foundation of China(No. 51175379)
文摘A methodology for performance optimization of torque converters is put forward based on the one-dimensional (1D) flow model. It is found that the inaccuracy of 1D flow model for predicting hydraulic performance at the low speed ratio is mainly caused by the separation phenomenon at the stator cascade which is induced by large flow impinging at the pressure side of the stator blades. A semi-empirical separation model is presented and incorporated to the original 1D flow model. It is illustrated that the improved model is able to predict the circumferential velocity components accurately, which can be applied to performance optimization. Then, the Pareto front is obtained by using the genetic algorithm (GA) in order to inspect the coupled relationship among stalling impeller torque capacity, stalling torque ratio and efficiency. The efficiency is maximized on the premise that a target stalling impeller torque capacity and torque ratio are achieved. Finally, the optimized result is verified by the computational fluid dynamics(CFD) simulation, which indicates that the maximal efficiency is increased by 0.96%.
基金Supported by the National Natural Science Foundation of China (50905016)
文摘A flexible flat torque converter was proposed to fulfill the requirement of miniaturization and power density maximization for automobiles.Constructed by two arcs joined by lines,the torus was designed directly from design path.The influence of flatness on the performance of the torque converter was evaluated.The software CFX and standard k-ε model were adopted to simulate the internal flow fields of the torque converter under different flatness ratios.The results indicated that the performance of the torque converter got worse as the flatness declined,but the capacity of pump increased.The efficiency and the torque ratio dropped slightly as the flatness ratio decreased.So the torque converter could be squashed appropriately to get high power density without too much efficiency sacrifice.But when the flatness ratio was below 0.2,there was a significant drop in the efficiency.
基金National Natural Science Foundation of China(Grant Nos.51975524,51405443)National Key Research and Development Program of China(Grant No.2019YFB2005200).
文摘The manufacturing of spiral groove structure of two-dimensional valve(2D valve)feedback mechanism has shortcomings of both high cost and time-consuming.This paper presents a novel configuration of rotary electro-mechanical converter with negative feedback mechanism(REMC-NFM)in order to replace the feedback mechanism of spiral groove and thus reduce cost of valve manufacturing.In order to rapidly and quantitative evaluate the driving and feedback performance of the REMC-NFM,an analytical model taking leakage flux,edge effect and permeability nonlinearity into account is formulated based on the equivalent magnetic circuit approach.Then the model is properly simplified in order to obtain the optimal pitch angle.FEM simulation is used to study the influence of crucial parameters on the performance of REMC-NFM.A prototype of REMC-NFM is designed and machined,and an exclusive experimental platform is built.The torque-angle characteristics,torque-displacement characteristics,and magnetic flux density in the working air gap with different excitation currents are measured.The experimental results are in good agreement with the analytical and FEM simulated results,which verifies the correctness of the analytical model.For torque-angle characteristics,the overall torque increases with both current and rotation angle,which reaches about 0.48 N·m with 1.5 A and 1.5°.While for torque-displacement characteristics,the overall torque increases with current yet decrease with armature displacement due to the negative feedback mechanism,which is about 0.16 N·m with 1.5 A and 0.8 mm.Besides,experimental results of conventional torque motor are compared with counterparts of REMC-NFM in order to validate the simplified model.The research indicates that the REMC-NFM can be potentially used as the electro-mechanical converter for 2D valves in civil servo areas.
文摘This text has expounded the working principle of realizing A/D conversion that utilizes the timer within MCU and combinesthe technology of PWM. The design of hardware circuit, improved gradual approached trial arithmetic and relevant program design arediscussed in detail. And it has analyzed the resolution of A/D converter based on the technology of PWM, etc.
文摘The proposed DAC consists of a unit current-cell matrix for 8MSBs and a binary-weighted array for 4LSBs,trading-off between the precision,speed,and size of the chip.In order to ensure the linearity of the DAC,a double Centro symmetric current matrix is designed by the Q2 random walk strategy.To achieve better dynamic performance,a latch is added in front of the current switch to change the input signal,such as its optimal cross-point and voltage level.For a 12bit resolution,the converter reaches an update rate of 300MHz.
文摘A 16 bit stereo audio novel stability fifth-order ∑△ A/D converter that consists of switched capacitor ∑△ modulators, a decimation filter, and a bandgap circuit is proposed. A method for the stabilization of a high order single stage ∑△ modulator is also proposed. A new multistage comb filter is used for the front end decimation filter. The ∑△ A/D converter achieves a peak SNR of 96dB and a dynamic range of 96dB. The ADC was implemented in 0. 5μm 5V CMOS technology. The chip die area occupies only 4. 1mm × 2.4mm and dissipates 90mW.
