Formation of High-quality Advanced High-k Oxide Layers at Low Temperature by Excimer UV Lamp-assisted Photo-CVD and Sol-gel Processing

We have successfully demonstrated that high quality and high dielectric constant layers can be fabricated by low temperature photo-induced or -assisted processing. Ta_2O_5 and ZrO_2 have been deposited at t<400 ℃ by means of a UV photo-CVD technique and HfO_2 by photo-assisted sol-gel processing with the aid of excimer lamps. The UV annealing of as-grown layers was found to significantly improve their electrical properties. Low leakage current densities on the order of 10 -8 A/cm 2 at 1 MV/cm for deposited ultrathin Ta_2O_5 films and ca.10 -6 A/cm 2 for the photo-CVD ZrO_2 layers and photo-irradiated sol-gel HfO_2 layers have been readily achieved. The improvement in the leakage properties of these layers is attributed to the UV-generated active oxygen species O( 1D) which strongly oxidize any suboxides to form more stoichiometric oxides on removing certain defects, oxygen vacancies and impurities present in the as-prepared layers. The photo-CVD Ta_2O_5 films deposited across 10.16-cm Si wafers exhibit a high thickness uniformity with a variation of less than \{±2.0%\} being obtained for ultrathin ca.10 nm thick films. The lamp technology can in principle be extended to larger area wafers, providing a promising low temperature route to the fabrication of a range of high quality thin films for future ULSI technology.

Fullerenol-containing Materials Derived by Sol-gel Processing

Water soluble fullerenols were synthesized and incorporated in SiO2, SiO2-TiO2, GPTMS-SiO2, GPTMS-ATPS inorganic and organic-inorganic materials by sol-gel processes. The maximum concentrations of C60(OH)n and C70(OH)n in the obtained SiO2 gels were estimated to be about 0.6% and 1.5% in weight, respectively. The characteristics of the UV/visible spectra of fullerenols in H2O and various gels were measured and compared. The thermal stability of fullerenols in gels was investigated with differential thermal analysis (DTA). The results indicate that the absorption features of fullerenols in solid gels are similar to those in H2O and the fullerenols in SiO2 are stable at 400℃. The optical limiting effect of the fullerenols was investigated preliminarily.

Sol-gel Processing of a Transparent Upconversion Luminescent Film with β-Na YF_4:Yb^(3+), Er^(3+) Microrods as Activator

β-Na YF4:Yb3+,Er3+ microrods were synthesized through hydrothermal methods. Polyethylene glycol with molecular weight of 6000 was used as surfactant. A series of transparent silica gel films with upconversion luminescence property was prepared through sol-gel method; the prepared β-Na YF4:Yb3+,Er3+ microrods were used as activator. The silica gel films show strong upconversion emission under excitation of 980-nm laser beam.

Sol-Gel Processing of Silica Nuclear Waste Glasses

A complex Sol-Gel process has been used for synthesis of silica glasses designed to contain high-level nuclear wastes. Cs, Sr, Co, and Nd (generically denoted Me) were used, the last as surrogate for actinides. Gels in the form of powders and sintered compacts were prepared by hydrolysis and polycondensation of tetraethoxide/Me nitrate solutions, which contained ascorbic acid as a catalyst. Thermal treatment studies were conducted on the resulting gels. Transformation to final products was studied by thermogravimetric analysis, infrared spectroscopy, and X-ray diffraction. Preliminary testing of Me leaching was also completed in quiescent water. Only a single dense form was resistant to

An Unprecedented Efficiency with Approaching 21%Enabled by Additive‑Assisted Layer‑by‑Layer Processing in Organic Solar Cells

Recently published in Joule,Feng Liu and colleagues from Shanghai Jiaotong University reported a record-breaking 20.8%power conversion efficiency in organic solar cells(OSCs)with an interpenetrating fibril network active layer morphology,featuring a bulk p-in structure and proper vertical segregation achieved through additive-assisted layer-by-layer deposition.This optimized hierarchical gradient fibrillar morphology and optical management synergistically facilitates exciton diffusion,reduces recombination losses,and enhances light capture capability.This approach not only offers a solution to achieving high-efficiency devices but also demonstrates the potential for commercial applications of OSCs.

基于Arduino与Processing的心率检测计设计研究

随着社会经济的高速发展,人们的物质生活也有了极大的提高,但同时也伴随着各种疾病的到来,身体健康已经成为人们普遍关注的焦点,因此,心率检测仪、血压计、血糖仪等各种家用医疗监测仪器已经逐渐融入日常生活。心脏病是人们难以预防的突发致命疾病之一,本文介绍的是一款基于Arduino【是基于易用硬件和软件的原型开源平台,包由可编程的电路板(简称微控制器),以及集成开发环境(称为Arduino IDE)的现成软件组成】Processing(开源编程语言,包括编辑器、编译器、展示器)的简易心率检测计系统,其功能实用、操作简单,可以测量心率,当超出正常心率范围时及时预警,是一款便携的实时心率测试仪。

Constraints on Characteristics and Distribution of Gas Hydrate and Free Gas Using Broad-Band Processing of Three-Dimensional Seismic Data

Gas hydrate drilling expeditions in the Pearl River Mouth Basin,South China Sea,have identified concentrated gas hydrates with variable thickness.Moreover,free gas and the coexistence of gas hydrate and free gas have been confirmed by logging,coring,and production tests in the foraminifera-rich silty sediments with complex bottom-simulating reflectors(BSRs).The broad-band processing is conducted on conventional three-dimensional(3D)seismic data to improve the image and detection accuracy of gas hydratebearing layers and delineate the saturation and thickness of gas hydrate-and free gas-bearing sediments.Several geophysical attributes extracted along the base of the gas hydrate stability zone are used to demonstrate the variable distribution and the controlling factors for the differential enrichment of gas hydrate.The inverted gas hydrate saturation at the production zone is over 40% with a thickness of 90 m,showing the interbedded distribution with different boundaries between gas hydrate-and free gas-bearing layers.However,the gas hydrate saturation value at the adjacent canyon is 70%,with 30-m-thick patches and linear features.The lithological and fault controls on gas hydrate and free gas distributions are demonstrated by tracing each gas hydrate-bearing layer.Moreover,the BSR depths based on broad-band reprocessed 3D seismic data not only exhibit variations due to small-scale topographic changes caused by seafloor sedimentation and erosion but also show the upward shift of BSR and the blocky distribution of the coexistence of gas hydrate and free gas in the Pearl River Mouth Basin.

Investigation on taste characteristics and sensory perception of soft-boiled chicken during oral processing based on electronic tongue and electronic nose

The sensory perception of food is a dynamic process,which is closely related to the release of flavor substances during oral processing.It’s not only affected by the food material,but also subjected to the individual oral environment.To explore the oral processing characteristics of soft-boiled chicken,the sensory properties,texture,particle size,viscosity,characteristic values of electronic nose and tongue of different chicken samples were investigated.The correlation analysis showed that the physical characteristics especially the cohesiveness,springiness,resilience of the sample determined oral processing behavior.The addition of chicken skin played a role in lubrication during oral processing.The particle size of the bolus was heightened at the early stage,and the fluidity was enhanced in the end,which reduced the chewing time to the swallowing point and raised the aromatic compounds signal of electronic nose.But the effect of chicken skin on chicken thigh with relatively high fat content,was opposite in electronic nose,which had a certain masking effect on the perception of umami and sweet taste.In conclusion,fat played a critical role in chicken oral processing and chicken thigh had obvious advantages in comprehensive evaluation of soft-boiled chicken,which was more popular among people.

Toluene Processed All-Polymer Solar Cells with 18%Efficiency and Enhanced Stability Enabled by Solid Additive:Comparison Between Sequential-Processing and Blend-Casting

The emergence of polymerized small molecule acceptors(PSMAs)has significantly improved the performance of all-polymer solar cells(all-PSCs).However,the pace of device engineering lacks behind that of materials development,so that a majority of the PSMAs have not fulfilled their potentials.Furthermore,most high-performance all-PSCs rely on the use of chloroform as the processing solvent.For instance,the recent highperformance PSMA,named PJ1-γ,with high LUMO,and HOMO levels,could only achieve a PCE of 16.1%with a high-energy-level donor(JD40)using chloroform.Herein,we present a methodology combining sequential processing(SqP)with the addition of 0.5%wt PC_(71)BM as a solid additive(SA)to achieve an impressive efficiency of 18.0%for all-PSCs processed from toluene,an aromatic hydrocarbon solvent.Compared to the conventional blend-casting(BC)method whose best efficiency(16.7%)could only be achieved using chloroform,the SqP method significantly boosted the device efficiency using toluene as the processing solvent.In addition,the donor we employ is the classic PM6 that has deeper energy levels than JD40,which provides low energy loss for the device.We compare the results with another PSMA(PYF-T-o)with the same method.Finally,an improved photostability of the SqP devices with the incorporation of SA is demonstrated.

Effects of friction stir processing and nano-hydroxyapatite on the microstructure,hardness,degradation rate and in-vitro bioactivity of WE43 alloy for biomedical applications

Nowadays,magnesium alloys are emerging in biomedical implants for their similar properties to natural bones.However,the rapid degradation of magnesium alloys in biological media hinders successful implantation.Refinement of microstructure,as well as reinforcement particles can significantly improve the degradation rate.In this work,multi-pass friction stir processing(FSP)was proposed to synthesize WE43/nano-hydroxyapatite(n HA)surface composite,the microstructure,reinforced particle distribution,micro-hardness,corrosion behavior and in-vitro bioactivity were studied.The subsequent FSP passes of WE43 alloy and WE43/n HA composite refined the grain size which was reduced by 94.29%and 95.92%(2.63 and 1.88μm,respectively)compared to base metal after three passes.This resulted in increasing the microhardness by 120%(90.86 HV0.1)and 135%(105.59 HV0.1)for the WE43 and WE43-n HA,respectively.It is found that increasing FSP passes improved the uniform distribution of n HA particles within the composite matrix which led to improved corrosion resistance and less degradation rate.The corrosion rate of the FSPed WE43/n HA composite after three passes was reduced by 38.2%(4.13 mm/year)and the degradation rate was reduced by 69.7%(2.87 mm/y).This is attributed to secondary phase(Mg24Y5and Mg41Nd5)particle fragmentation and redistribution,as well as a homogeneous distribution of n HA.Additionally,the growing Ca-P and Mg(OH)2layer formed on the surface represented a protective layer that reduced the degradation rate.The wettability test revealed a relatively hydrophilic surface with water contact angle of 49.1±2.2°compared to 71.2±2.1°for base metal.Also,biomineralization test showed that apatite layer grew after immersion 7d in simulated body fluid with atomic ratio of Ca/P 1.60 approaching the stoichiometric ratio(1.67)indicating superior bioactivity of FSPed WE43/n HA composite after three passes.These results raise that the grain refinement by FSP and introduction of n HA particles significantly improved the degradation rate and in-vitro bioactivity of WE43 alloy for biomedical applications.

A new insight into LPSO phase transformation and mechanical properties uniformity of large-scale Mg-Gd-Y-Zn-Zr alloy prepared by multi-pass friction stir processing

A large-scale fine-grained Mg-Gd-Y-Zn-Zr alloy plate with high strength and ductility was successfully prepared by multi-pass friction stir processing(MFSP)technology in this work.The structure of grains and long period stacking ordered(LPSO)phase were characterized,and the mechanical properties uniformity was investigated.Moreover,a quantitative relationship between the microstructure and tensile yield strength was established.The results showed that the grains in the processed zone(PZ)and interfacial zone(IZ)were refined from 50μm to 3μm and 4μm,respectively,and numerous original LPSO phases were broken.In IZ,some block-shaped 18R LPSO phases were transformed into needle-like 14H LPSO phases due to stacking faults and the short-range diffusion of solute atoms.The severe shear deformation in the form of kinetic energy caused profuse stacking fault to be generated and move rapidly,greatly increasing the transformation rate of LPSO phase.After MFSP,the ultimate tensile strength,yield strength and elongation to failure of the large-scale plate were 367 MPa,305 MPa and 18.0% respectively.Grain refinement and LPSO phase strengthening were the major strengthening mechanisms for the MFSP sample.In particularly,the strength of IZ was comparable to that of PZ because the strength contribution of the 14H LPSO phase offsets the lack of grain refinement strengthening in IZ.This result opposes the widely accepted notion that IZ is a weak region in MFSP-prepared large-scale fine-grained plate.

Microstructural evolution and its influence on mechanical and corrosion behaviors in a high-Al/Zn containing duplex Mg-Li alloy after friction stir processing

Ultralight Mg-Li alloys offer promising applications across various fields.Mg-Li alloys enriched with Al and Zn hold theoretical potential for achieving excellent mechanical strength and corrosion resistance.However,the structural and performance characteristics of such Mg-Li alloys,particularly after thermo-mechanical processing,remain inadequately explored and understood.This study investigated the mi-crostructural evolution of a Mg-9Li-5Al-4Zn alloy after friction stir processing and its consequent effects on the mechanical and corrosion performance.The grain size of the alloy was effectively refined and sta-bilized during friction stir processing at various heat inputs.The yield strength of the alloy increased by 86.4%after friction stir processing under the highest heat input condition,which was attributed to fine grain strengthening,solid solution strengthening and dispersion strengthening.Concurrently,the alloy ex-perienced a slight decrease in elongation after the friction stir processing.The alloy subjected to friction stir processing with the highest heat input exhibited a minimal corrosion current density of 6.10×10^(−6) A/cm^(2),which was only 25%of the base metal.The enhanced anti-corrosion properties can be attributed to the dispersion and distribution of precipitated particles induced by friction stir processing,which hin-dered the micro-galvanic corrosion and promoted the generation of a compact surface film,leading to minimal and uniform corrosion.This investigation can be significant for understanding the metallurgical mechanisms and performance evolution of Mg-Li alloys during thermomechanical processes.

Lower temperature synthesis of cerium-doped polycrystalline lutetium pyrosilicate powders by a novel sol-gel processing

A novel sol-gel processing was developed to synthesize polycrystalline cerium-doped lutetium pyrosilicate （Lu2Si2O7Ce, LPS ：Ce） powders under low temperature. It was found that the addition of propylene oxide （PPO） could promote the formation of Lu-O-Si bonds in precursor, which was beneficial to the formation of LPS phase. X-ray diffraction （XRD） patterns indicated that the single-phased LPS powder was well crystallized at 1050℃. Microstructure observation demonstrated that the synthetic LPS powder was composed of ellipsoidal grains with the mean size of 40 nm. The luminescent properties were characterized by photoluminescence （PL）, X-ray excited luminescence （XEL） and vacuum ultraviolet （VUV） spectroscopy at room temperature. The synthetic LPS：Ce powder emitted a broad emission spectrum centered at about 380 nm, which should be ascribed to the 5d→4f transition of Ce3＋. Decay time of the synthetic LPS：Ce powder was measured to be only 32 ns.

Development and Validation of Integrated Nutrient Management Practices of Industrial Processing Varieties: Asterix and Courage in Bangladesh

An experiment was meticulously conducted at the research field of Bangabandhu Sheikh Mujibur Rahman Agricultural University (BSMRAU), Gazipur, Bangladesh, during the 2011-2012 potato growing season to develop integrated crop management practices for the potato seed production of industrial processing varieties Asterix and Courage. Significantly, higher growth and yield parameters were found in the BADC-recommended practice. Later, another experiment was conducted to validate the BADC practice during the 2013-2014 potato growing season in two locations in Bangladesh. Results showed that the production of tuber per hill, tuber weight per hill as well as gross tuber yield per plot, higher proportion of storable seed tubers, and more quality seed potatoes (A-grade and B-grade) seed tubers were found significantly higher in the “BADC developed practice” compared to other treatments. Viral diseases (PLRV and PVY) prevalence was lower in “BADC developed practice”. Moreover, “BADC developed practice” contributed more economic yield by minimizing input cost compared to “Munshiganj advanced farmers’ practice”. Therefore, the “BADC developed practice” was found “superior” regarding yield, quality, and profitability in seed potato production of industrial varieties—Asterix and Courage in Bangladesh.

Improved Responses with Multitaper Spectral Analysis for Magnetotelluric Time Series Data Processing:Examples from Field Data

In order to attain good quality transfer function estimates from magnetotelluric field data(i.e.,smooth behavior and small uncertainties across all frequencies),we compare time series data processing with and without a multitaper approach for spectral estimation.There are several common ways to increase the reliability of the Fourier spectral estimation from experimental(noisy)data;for example to subdivide the experimental time series into segments,taper these segments(using single taper),perform the Fourier transform of the individual segments,and average the resulting spectra.

Literature classification and its applications in condensed matter physics and materials science by natural language processing

The exponential growth of literature is constraining researchers’access to comprehensive information in related fields.While natural language processing(NLP)may offer an effective solution to literature classification,it remains hindered by the lack of labelled dataset.In this article,we introduce a novel method for generating literature classification models through semi-supervised learning,which can generate labelled dataset iteratively with limited human input.We apply this method to train NLP models for classifying literatures related to several research directions,i.e.,battery,superconductor,topological material,and artificial intelligence(AI)in materials science.The trained NLP‘battery’model applied on a larger dataset different from the training and testing dataset can achieve F1 score of 0.738,which indicates the accuracy and reliability of this scheme.Furthermore,our approach demonstrates that even with insufficient data,the not-well-trained model in the first few cycles can identify the relationships among different research fields and facilitate the discovery and understanding of interdisciplinary directions.

Modulation of starch digestibility using non-thermal processing techniques:A review

Obesity and type 2 diabetes are widespread throughout the world, especially in developed countries. Starch is an important part of human staple food, the modulating of starch digestibility is conducive to reducing postprandial blood glucose levels and alleviating the chronic disease caused by high caloric intake. The digestion properties of starch are correlated with its structural features, including crystallization, amylose/amylopectin ratio, non-starch components, etc. Among the modified methods applied to regulate starch digestibility, non-thermal processing techniques(NTPT) receive extensive attention due to the characteristics of safety, environmental friendliness and high efficiency. The influence and mechanism of NTPT on the digestion properties of starch are discussed in this review, including ultrasounds, high pressure, γ-irradiation, etc. NTPT induces the alternation of morphological and structural characteristics of native starch, changing their sensitivity to enzymes. The effects of NTPT on the digestibility of starch are highly related to the processing parameters and structure characteristics of native starch. The review shows that NTPT is an effective way to modulate the digestion properties of starch and prevent people from suffering from chronic diseases such as obesity and type 2 diabetes.

Fresh Processing Technology in Polygonatum odoratum Production Area and Its Comparison with Traditional Processing

[Objectives]To compare the effects of traditional processing and fresh processing on the quality of Polygonatum odoratum decoction piece.[Methods]The effects of fresh processing and traditional processing on the quality of P.odoratum decoction piece were compared and analyzed with appearance characteristics,total ash content,extract content,total polysaccharides content,and total flavonoids content as the evaluation indexes.[Results]Fresh processing method in different production areas has different effects on P.odoratum decoction piece.P.odoratum was dried in oven of 50℃.When moisture content was 41.44%-59.67%,it was cut.After complete drying at 50℃,the moisture content of dried P.odoratum was 8.94%-9.60%,and ethanol-soluble extract content was 77.29%-78.20%,and water-soluble extract was 77.7%-78.14%.At this time,the appearance characteristics of section of P.odoratum decoction piece were better than that of traditional processing,which was yellowish white.The total polysaccharide content was higher than that of traditional processing,and the content of total flavonoids was statistically significant different from that of traditional processing.[Conclusions]The quality of P.odoratum decoction piece by fresh processing is better than that of the traditional processing,and it is feasible to use fresh processing.

Laser processing induced nonvolatile memory in chaotic graphene oxide films for flexible reservoir computing applications

Graphene oxide,as a 2D material with nanometer thickness,offers ultra-high mobility,chaotic properties,and low cost.These make graphene oxide memristors beneficial for reservoir computing(RC)networks.In this study,continuous-wave(CW)laser processing is used to reduce chaotic graphene oxide(CGO)films,resulting in the non-volatile storage capability based on the reduced chaotic graphene oxide(rCGO)films.Laser power significantly impacts the characteristics of the rCGO memristor.Material characterization indicates that laser radiation can effectively reduce the oxygen content in CGO films.With optimized laser power,the rCGO memristor achieves a large ratio at 18 mW laser power.Benefiting from the short-term mem-ory characteristics,distinct conductive states are achieved,which are further utilized to construct RC networks.With a third con-trol probe,the rCGO memristor can express rich reservoir states,demonstrating accuracy in predicting the Hénon map with an NRMSE below 0.3.These findings provide the potential for developing flexible RC networks based on graphene oxide memris-tors via laser processing.

Processing在高中信息技术教学中的应用

信息技术教学注重对学生计算思维等核心素养的培养,Processing具有开源简洁、可视化反馈和应用广泛等特点,打破了传统编程工具的局限性,为高中信息技术教学提供了新的思路。本文根据项目学习相关理论,提出了Processing项目教学策略,该策略以学生探究活动为中心,包含情境创设、项目分析、任务探究、反思优化和总结拓展五个环节。同时,作者基于大单元教学理念,设计开发了Processing算法与程序设计课程,在高中信息技术教学中开展了实践,促进了学生核心素养、设计思维和创新实践能力的培养。