Abrasive resistance of metastable V–Cr–Mn–Ni spheroidal carbide cast irons using the factorial design method

Full factorial design was used to evaluate the two-body abrasive resistance of 3wt%C–4wt%Mn–1.5wt%Ni spheroidal carbide cast irons with varying vanadium（5.0wt%–10.0wt%） and chromium（up to 9.0wt%） contents. The alloys were quenched at 920℃. The regression equation of wear rate as a function of V and Cr contents was proposed. This regression equation shows that the wear rate decreases with increasing V content because of the growth of spheroidal VC carbide amount. Cr influences the overall response in a complex manner both by reducing the wear rate owing to eutectic carbides（M7C3） and by increasing the wear rate though stabilizing austenite to deformation-induced martensite transformation. This transformation is recognized as an important factor in increasing the abrasive response of the alloys. By analyzing the regression equation, the optimal content ranges are found to be 7.5wt%–10.0wt% for V and 2.5wt%–4.5wt% for Cr, which corresponds to the alloys containing 9vol%–15vol% spheroidal VC carbides, 8vol%–16vol% M7C3, and a metastable austenite/martensite matrix. The wear resistance is 1.9–2.3 times that of the traditional 12wt% V–13wt% Mn spheroidal carbide cast iron.

Performance comparison of training algorithms for the estimation of B?hme abrasion resistance using neural networks

Natural stones used as floor and wall coverings are exposed to many different abrasive forces,so it is essential to choose suitable materials for wear resistance in terms of the life of the structure.The abrasion resistance of natural stones can be determined in the laboratory by applying the B?hme abrasion resistance(BAR)test.However,the direct analysis of BAR in the laboratory has disadvantages such as wasting time and energy,experimental errors,and health impacts.To eliminate these disadvantages,the estimation of BAR using artificial neural networks(ANN)was proposed.Different natural stone samples were collected from Türkiye,and uniaxial compressive strength(UCS),flexural strength(FS),water absorption rate(WA),unit volume weight(UW),effective porosity(n),and BAR tests were carried out.The outputs of these tests were gathered and a data set,consisting of a total of 105 data,was randomly divided into two groups:testing and training.In the current study,the success of three different training algorithms of Levenberg-Marquardt(LM),Bayesian regularization(BR),and scaled conjugate gradient(SCG)were compared for BAR prediction of natural stones.Statistical criteria such as coefficient of determination(R~2),mean square error(MSE),mean square error(RMSE),and mean absolute percentage error(MAPE),which are widely used and adopted in the literature,were used to determine predictive validity.The findings of the study indicated that ANN is a valid method for estimating the BAR value.Also,the LM algorithm(R~2=0.9999,MSE=0.0001,RMSE=0.0110,and MAPE=0.0487)in training and the BR algorithm(R~2=0.9896,MSE=0.0589,RMSE=0.2427,and MAPE=1.2327)in testing showed the best prediction performance.It has been observed that the proposed method is quite practical to implement.Using the artificial neural networks method will provide an advantage in similar laborintensive experimental studies.

Microstructures and wear resistance of high boron and low carbon ferroalloy using hybrid powder/wire overlaying method

The high boron alloy surfacing layer was easily cracked due to its insufficient toughness by using hybrid powder/ wire overlaying method. In order to explore the cracked mechanism, the microstructures and the wear resistance of the samples with different boron contents were studied. Further, phases analysis, microhardness, macrohardness and wear test were also carried out. The boron content depended microstructures were observed. The precipitation of the Fe2B, Fe3 （ C, B）, Fe23 （C, B）6 were increased with the increase of boron content. It was found that the wear resistance was independent of the macrohardness as the macrohardness increased firstly and then remained steady at -62 HRC. However, the wear resistance was depended on the boron contents, and which increased with the increase of the boron contents. The abrasive loss mechanism changed from plastic deformation removal to fracture removal.

Dual-physical network PVA hydrogel commensurate with articular cartilage bearing lubrication enabled by harnessing nanoscale crystalline domains

Hydrogel, as one of potential soft materials for articular cartilage, has encountered pressing obstacles, such as insufficient mechanical properties, poor lubrication, and easy to wear. To tackle these, we propose a strong yet slippery polyvinyl alcohol/chitosan (PVA/CS) hydrogel with dual-physically crosslinked networks by harnessing freeze-thawing, salting-out, annealing, and rehydration. High mechanical properties of PVA/CS hydrogel can be readily regulated by adjusting proportion of PVA/CS and annealing temperature. The optimized hydrogel exhibits high mechanical properties with tensile strength of ∼ 19 MPa at strain of 550%, compression strength of ∼ 11 MPa at small strain of 39%, and outstanding toughness and antifatigue owing to the robust physical interactions, including hydrogen bonds, crystallization, and ionic coordination. Moreover, the equilibrium hydrogel shows low friction coefficient of ∼ 0.05 against Al_(2)O_(3) ball under the condition of 30 N, 1 Hz, with water as the tribological medium, which is close to the lubrication performance of native cartilage. And meanwhile, the proposed cartilage-like slippery hydrogel displays stable long-term lubrication performance for 1 × 10^(5) reciprocating cycles without destructive wear and structure damage. It is therefore believed that the biocompatible cartilage-like slippery hydrogel opens innovative scenarios for developing cartilage-mimicking water-lubricated coating and biomedical implants with satisfactory load-bearing and lubrication performance.

Effect of surface Cr/C infiltration on microstructure,mechanical properties and wear resistance of high chromium cast iron

A new type of high chromium cast iron(HCCI)was prepared,and its microstructure,mechanical properties,and abrasion resistance were investigated systematically.Results showed that after surface carburizing and chromizing,the microstructure of HCCI mainly consists of martensite,boride(M_(2)B),and carbide(M_(7)C_(3)),accompanied with a large amount of secondary precipitations M_(23)C_(6).Moreover,the morphology and hardness of the carbide and boride in HCCI change little,while the volume fraction of carbide and boride increases from 16.23%to 23.16%.This effectively increases the surface hardness of HCCI from 64.53±0.50 HRC to 66.58±0.50 HRC,with the result that the surface of HCCI possesses a better abrasion resistance compared to the center position.Furthermore,the wear mechanism of HCCI changes from micro-plowing to micro-cutting with the increase of surface hardness.

Influence of secondary carbide precipitation and transformation on abrasion resistance of a 3Cr15Mo1V1.5 white iron

The relationship between the secondary carbide precipitation and transformation of the 3Cr15Mo1V1.5 white iron and abrasion resistance was investigated by using optical microscope （OM）, transmission electron microscopy （TEM） and X-ray diffrac- tion （XRD）. The results show that the properties of secondary carbides precipitated at holding stage play an important role in the abrasion resistance. After certain holding time at 833 K subcritical treatment, the grainy （Fe, Cr）23C6 carbide precipitated and the fresh martensite transformed at the holding stage for 3Cr15Mo1V1.5 white iron improve the bulk hardness and abrasion resistance of the alloy. Prolonging holding time, MoC and （Cr, V）2C precipitations cause the secondary hardening peak and the corresponding better abrasion resistance. Finally, granular （Fe, Cr）23C6 carbide in situ transforms into laminar M3C carbide and the matrix structure transforms into pearlitic matrix. These changes weaken hardness and abrasion resistance of the alloy sharply.

The Abrasion-resistance Investigation of Rubberized Concrete

The abrasion resistance properties of rubberized concrete were comparatively studied by taking silica fume and crumb tire rubber as the additives. The abrasion tests were conducted in accordance with the Chinese standard test method DL/T 5150 - 2001, two recommended test methods： under water method and ring method, were used. The crumb tire rubbers with the sieve size of 8-mesh and 16-mesh were incorporated into the concrete by replacing same volume of sand and as an additive. The abrasion resistance of concrete was evaluated according to the abrasion resistance strength and the mass loss. Test results show that the addition of silica fume enhanced both compressive strength and abrasion resistance of concrete, and the addition of crumb rubber reduced the compressive strength but increased notably the abrasion resistance of the concrete. Silica fume concrete performed a better abrasion resistance than control concrete, and the rubberized concrete performed a much better abrasion resistance than silica fume concrete. The abrasion resistance of rubberized concrete increased with the increase of rubber content.

Influences of Polypropylene Fiber and SBR Polymer Latex on Abrasion Resistance of Cement Mortar

Influences of polypropylene （PP） fiber and styrene-butadiene rubber （SBR） polymer latex on the strength performance, abrasion resistance of cement mortar were studied. The experimental results show that the flexural strength, brittleness index （σF/σC） and abrasion resistance can be improved significantly by the addition of PP fiber and SBR polymer latex. The relationship between the flexural strength and abrasion resistance was analyzed, showing a good linear relationship between them. The reinforced mechanism of PP fiber and SBR polymer latex on cement mortar was analyzed by some microscopic tests. The test results show that the addition of SBR polymer latex has no significant influence on the cement hydration after 7 d curing. Adding SBR polymer latex into cement mortar can form a polymer transition layer in the interfaces of PP fiber and cement hydrates, which improves the bonding properties between the PP fiber and cement mortar matrix effectively.

Relations of abrasion resistance and hardness of 16Cr-3C white irons with retained austenite content

The relationship between the retained austenite content of the matrix in16Cr-3C white irons and the abrasion resistance was investigated. The results show that: (1) theabrasion resistance can be improved by sub-critical heat treatment, which could be attributed to thedecrease of the retained austenite content; (2) both the abrasion resistance and hardness can beimproved by controlling the retained austenite content below 20 percent-30 percent and arrive at themaximum when the retained austenite content is reduced to about 10 percent; (3) the abrasionresistance decreases abruptly once the retained austenite content is lower than 10 percent, whichstems from both the in situ transformation of (Fe, Cr)_(23)C_6 to M_3C carbides and the formation ofpearlitic matrix.

Abrasion Resistance of Cement Paste with Granulated Blast Furnace Slag and Its Relations to Microhardness and Microstructure

The abrasion resistance of cement pastes with 30 wt%,40 wt%and 50 wt%granulated blast furnace slag(GBFS),and its relations to microhardness and microstructure like hydration products and pore structure were studied.Results indicated that GBFS decreased the abrasion resistance of paste,and among the pastes with GBFS,the paste with 40 wt%GBFS showed the highest abrasion resistance.The microhardness of GBFS was lower than that of the cement,and the microhardness of the hydration products in paste with GBFS was also lower than that of the hydration products in paste without GBFS,so that the abrasion resistance of paste decreased when GBFS was incorporated.The reason for the decrease of microhardness of pastes with GBFS was that the contents of Ca(OH)_(2)in pastes with GBFS was significantly lower than that in the paste without GBFS,while large amounts of calcium aluminate hydrates and hydrotalcite-like phases(HT)in pastes with GBFS were generated.Furthermore,among the pastes with GBFS,the paste with 40 wt%GBFS showed the lowest porosity which was the main reason for its highest abrasion resistance.

Mechanism of C_(4)AF Content and Heat-curing Process on the Abrasion Resistance of High Ferrite Cement

Cement used in severe maritime environments must be attached with exceptional properties such as high sulfate resistance and abrasion strength.A sulfate resistant material typically used in marine engineering is high ferrite cement,which has been utilized in sulfate-rich environments.This study aims at exploring the effect of C_(4)AF and heat-curing on the abrasion resistance of high ferrite cement(HFC,C_(4)AF:14%-22%)in order to have a comprehensive understanding of this mechanism and promote the application of HFC in marine engineering.A new invention was designed for the abrasion resistance device by considering the sea-wave abrasion and seawater erosion in laboratory.The compressive strength and abrasion resistance of HFC were measured.Additionally,advanced analytical methods were used to explore the abrasion resistance mechanism of HFC,including X-ray fluorescence(XRF),X-ray diffraction(XRD),and thermogravimetric(TG)analyses,as well as mercury intrusion porosimetry(MIP).The results showed that HFC had the best abrasion resistance under appropriate heat-curing system that the curing temperature was 50℃and the hosting time was 4 hours,compared with PI(Portland cement)and LHC(low heat cement),meanwhile the abrasion resistance of HFC had a 62.4%increase when C_(4)AF content is increased from 14%to 22%.It can be ascribed that the content of portlandite is decreased due to the increase of C_(4)AF,which can reduce the portlandite assembled in ITZ(interfacial transition zone).It can also be ascribed that the DEF(delayed ettringite formation)is successfully avoided in HFC and the hydration degree of HFC can continue to be boosted under appropriate heat-curing system.

A New Test Method for Hot Abrasion Resistance on Refractories

Test methods for hot abrasion resistance of refractories in China and overseas were briefly introduced. A new test method for hot abrasion resistance was researched. The new method inherits test principle of cold abrasion resistance in Chinese standard totally, adopts compressed air pre-heating and electricity heating sam- ples, and is featured with complete structure, good con- trollability, simple operation, and small size. The characteristics and operating procedure of HAT-14A tester were introduced. The hot abrasion resistance of various refractories at different temperatures was tested.

Effect of the CaF_2-fraction in the glass-ceramic with abrasion resistance on crystallization

Investigated the effect of an addition of CaF2 on the crystallization of a glass-ceramic with abrasion resistance. X-ray diffraction, differential thermal analysis and scanning electron microscopy were used to determine the effect. The results showed that a suitable addition of CaF2 promoted crystallization by forming an interme- diate crystalline phase. CaF2 can decrease the temperature and active energy of the base-glass for crystallization. When 4 mass-% of CaF2-fraction is added in the glass, the crystallization temperature and active energy is 936 ℃and 172.75 kJ/mol respectively. When CaF2 is increased to 6 mass-%, the temperature and active energy decrease to 890 ℃ and 88.81 kJ/mol. CaF2 is an efficient nucleating agent for the glass-ceramics with abrasion resistant, the optimal content of CaF2 is about 6 mass-%.

Research of Test Method on Abrasion Resistance at Elevated Temperatures of Refractories

In this work,the factors and parameters of a test method on abrasion resistance at elevated temperatures were discussed and researched.First of all,the precision tests of the test method on abrasion resistance at elevated temperatures were conducted in 8 laboratories.The results such as the standard deviation and reproducibility show good repeatability and reliability.The relationship between the stability of refractory performance and the standard deviation of their wear value was analyzed.Then the impact of the heat treatment condition of unshaped refractories and oxidation of SiC sand as abrasive on the lost volume of the tested specimens was researched.

Chinese Standards on Refractories Refractory Products-Determination of Abrasion Resistance at Ambient Temperature GB/T 18301-2012

This standard specifies the terms and definitions, theory, apparatus, specimens, test procedures, calcu- lation results, apparatus check and test reports, etc. of abrasion resistance at ambient temperature of refractory products.

Enhancing Mar and Abrasion Resistance of Acrylic Hard Coatings with Soft Base Layer

Mar and abrasion resistance were investigated by a progressive load scratch test and steel wool abrasion test, respectively. Two acrylic coating systems including trimethylolpropane triacrylate (TMPTA) and pentaerythritol triacrylate (PETA) were prepared. A soft base layer was introduced as an intermediate layer between two different types of top layer and poly (methyl methacrylate) (PMMA) substrate to demonstrate the effect of soft base layer on mar and abrasion resistance. Abrasion damage on the coating surface was found to be less severe, when the soft base layer was incorporated into the coating systems. The reduction in scratch coefficient of friction (SCOF) and surface roughness was also observed. The results suggested that mar and abrasion resistance was greatly influenced by the presence of soft base layer, although different top layers were used. Moreover, it was found that abrasion resistance was further improved as the thicker soft base layer was applied.

Improving the Abrasion Resistance of ＂Green＂ Tyre Compounds

Since the introduction of＂green tyres＂ in the early 90＇s, the use of silica as a reinforcing filler, along with a silane coupling agent, has spread and grown worldwide. The greatest advantage of using silica over carbon black as reinforcing filler in a tyre tread compound is that a lower rolling resistance is achieved, while maintaining good wet traction. However, a previous study has shown that the wear resistance of a silica filled ENR （epoxidised natural rubber） compound was not as high as those of conventional OESBR （oil extended styrene butadiene rubber） and NR/BR compounds used in passenger car and truck tyre treads. In this work, with the aim of improving abrasion resistance, the effect of blending BR （butadiene rubber） into a silica filled ENR compound was studied. Blends with 0 to 30 phr BR were prepared in a Polylab Haake internal mixer. The rheological properties of the compounds were measured using a Mooney viscometer and oscillating-disc rheometer. The hardness, tensile strength and DIN abrasion resistance were also measured. The results showed that the ENR/silica compound properties such as tensile strength and hardness were as good as those of the conventional compounds. However, the most important finding was that abrasion resistance increased significantly with BR content, exceeding that of the conventional compound at BR： ENR ratios of greater than 20：80.

Microstructure and Wear Resistance Properties of FeCrAl-Cu(Ni,Co)HEA Coatings Synthesized by Laser Remelting

FeCrAlCu,FeCrAlCuNi,FeCrAlCuCo,and FeCrAlCuNiCo high-entropy alloy(HEA)coatings were synthesized on the surface of 45#steel through cold spraying-assisted laser remelting.Results reveal that all four HEA coatings are composed of face-centered cubic+body-centered cubic phases.Additionally,the microstructure of the coatings consists of columnar dendrites.With the simultaneous addition of both Ni and Co elements,the columnar dendritic grains are gradually refined in the coating.Moreover,the FeCrAlCuNiCo HEA coating exhibits excellent friction performance with the coating hardness of 5847.7 MPa,friction factor of 0.45,and wear rate of 3.72×10^(−5) mm^(3)·N^(−1)·m^(−1).The predominant wear mechanism is the adhesive wear and abrasive wear.

Study on the new materials for fiberboard refiner plate of defibrator

Defibrator is a very important machine in the wood industry for producing fiberboard. The refiner plates are the key parts of defibrator that directly act with the wood, and broken easily. The working life of the refiner plates is of significance to the wood industry. It may affect refining quality, production efficiency, and power consumption. In this paper, the abrasion resistance of the refiner plate made of different materials, the stainless steels and high chromium cast irons, were tested and compared. The results showed that abrasion resistance of refiner plate made of high chromium cast irons was better than that of the stainless steel materials. Although the two kinds of materials have the same compositions, their abrasion resistances have ap-parent difference. The main reason is that the material microstructures have very important effects on their performance. The refiner plates made of developed high chromium cast irons don抰 demand the complex heat treatment. This can simplify the producing process, save the cost of production, decrease labor strength, and increase the production efficiency.

Effect of Graphite Content and Granularity on Mechanical and Tribological Properties of Bronze Alloyed Powder Composite

The bronze alloyed powder composite containing nanoparticles was developed by hot pressing.The effects of the content and granularity of graphite on hardness,machinability,bending strength,compression strength,and friction and wear behavior of the composites were studied.The microstructures of the specimens were analyzed by SEM.The results showed that the graphites are distributed in net when nanographites are added,resulting in the decrease of mechanical properties and abrasive resistance.When the content of nanographite is 10%,the composite is brittle.The graphite is distributed in the form of block when micrographite is added,improving the mechanical properties and abrasive resistance.Wear track was studied by SEM.