Ash removal from inferior coal via ammonium fluoride roasting and simultaneous yield of white carbon black

The quality upgrading and deashing of inferior coal by chemical method still faces great challenges.The dangers of strong acid,strong alkali,waste water and exhaust gas as well as high cost limit its industrial production.This paper systematically investigates the ash reduction and desilicification of two typical inferior coal utilizing ammonium fluoride roasting method.Under the optimal conditions,for fat coal and gas coal,the deashing rates are 69.02%and 54.13%,and the desilicification rates are 92.64%and 90.27%,respectively.The molar dosage of ammonium fluoride remains consistent for both coals;however,the gas coal,characterized by a lower ash and silica content(less than half that of the fat coal),achieves optimum deashing effect at a reduced time and temperature.The majority of silicon in coal transforms into gaseous ammonium fluorosilicate,subsequently preparing nanoscale amorphous silica with a purity of 99.90%through ammonia precipitation.Most of the fluorine in deashed coal are assigned in inorganic minerals,suggesting the possibility of further fluorine and ash removal via flotation.This research provides a green and facile route to deash inferior coal and produce nano-scale white carbon black simultaneously.

Optimization of mixing speed and time to disperse the composite conductive agent composed of carbon black and graphene in lithium-ion battery slurry

This paper proposed an optimal approach to disperse the composite conductive agent which is composed of carbon black(CB)and graphene(Gr)within lithium-ion battery(LIB)slurry with different mixing speeds and mixing times.The internal structures of LIB slurry are characterized by Electrochemical Impedance Spectroscopy,Scanning Electron Microscopy,and Raman experiment.Initially,a composite conductive solution is prepared by mixing the composite conductive agent with NMP solvent under the conditions of five different mixing speeds n_(1)(n_(1)=1000,1100,1200,1300,1400 rpm)in the case of mixing time t_(1)=10 min.Subsequently,LIB slurry is prepared by blending the composite conductive solution,LiCoO_(2)and PVDF-NMP solution under the conditions of five different mixing speeds n_(2)(n_(2)=1000±280,1100±280,1200±280,1300±280,1400±280 rpm)in the case of mixing time t_(2)=6 min.By analyzing the internal structure of different LIB slurries,it shows that in the case of n_(1)=n_(2)=1200 rpm,a conductive network structure is well formed within LIB slurry.Additionally,in order to determine the optimal time to prepare the composite conductive solution for LIB slurry,nine different t_(1)(t_(1)=0,10,20,30,40,50,60,70,80 min)are selected.By analyzing the internal structure of different LIB slurries,a well-formed conductive network structure and a uniformly distributed composite conductive agent are deduced in LIB slurry when t_(1)=50 min.Therefore,it can be concluded that the composite conductive agent composed of CB and Gr is able to be uniformly dispersed in LIB slurry by establishing a well-formed conductive network structure under the optimal mixing speed n_(1)=n_(2)=1200 rpm and the optimal mixing time t_(1)=50 min,t_(2)=6 min.This kind of the internal structure has the potential to be used to further analyze the dispersion characterizations of LIB slurry under different composite conductive agent and CB/Gr ratios with the aim of improving the final performance of LIB.

A progress review of black carbon deposition on Arctic snow and ice and its impact on climate change

The rapid warming of the Arctic,accompanied by glacier and sea ice melt,has significant consequences for the Earth’s climate,ecosystems,and economy.Black carbon(BC)deposition on snow and ice can trigger a significant reduction in snow albedo and accelerate melting of snow and ice in the Arctic.By reviewing the published literatures over the past decades,this work provides an overview of the progress in both the measurement and modeling of BC deposition and its impact on Arctic climate change.In summary,the maximum value of BC deposition appears in the western Russian Arctic(26 ng·g^(–1)),and the minimum value appears in Greenland(3 ng·g^(–1)).BC records in the Arctic ice core already peaked in 1920s and 1970s,and shows a regional difference between Greenland and Canadian Arctic.The different temporal variations of Arctic BC ice core records in different regions are closely related to the large variability of BC emissions and transportation processes across the Arctic region.Model simulations usually underestimate the concentration of BC in snow and ice by 2–3 times,and cannot accurately reflect the seasonal and regional changes in BC deposition.Wet deposition is the main removal mechanism of BC in the Arctic,and observations show different seasonal variations in BC wet deposition in Ny-Ålesund and Barrow.This discrepancy may result from varying contributions of anthropogenic and biomass burning(BB)emissions,given the strong influence by BC from BB emissions at Barrow.Arctic BC deposition significantly influences regional climate change in the Arctic,increasing fire activities in the Arctic have made BB source of Arctic BC more crucial.On average,BC in Arctic snow and ice causes an increase of+0.17 W·m^(–2)in radiative forcing and 8 Gt·a^(–1)in runoff in Greenland.As stressed in the latest Arctic Monitoring and Assessment Programme report,reliable source information and long-term and high-resolution observations on Arctic BC deposition will be crucial for a more comprehensive understanding and a better mitigation strategy of Arctic BC.In the future,it is necessary to collect more observations on BC deposition and the corresponding physical processes(e.g.,snow/ice melting,surface energy balance)in the Arctic to provide reliable data for understanding and clarifying the mechanism of the climatic impacts of BC deposition on Arctic snow and ice.

A novel nanofluid of modified carbon black nanoparticles for enhanced oil recovery in low permeability reservoirs

A novel nanofluid of modified carbon black(MCB)nanoparticles was initially developed for enhanced oil recovery(EOR)in low permeability reservoirs.The MCB nanoparticles were obtained via a three-step reaction involving modification by oxidation,acyl chlorination,and activated grafting.MCB nano-particles were spherically dispersed,with an average size of 72.3 nm.Compared with carbon black(CB)nanoparticles,dispersed MCB nanoparticles can effectively reduce the oil-water interfacial tension(IFT)to 10^(-2)mN/m and change the surface wettability of sand particles.Based on the results of core flooding experiments,the MCB nanoparticles exhibited a better EOR capacity than surfactants and CB nano-particles,and the final oil recovery was significantly increased by 27.27%.The core scanning test showed that the MCB nanoparticles could plug high permeability channels by adsorbing onto the surfaces of sand particles and forming larger aggregates that bridge across pores or throats,resulting in a higher swept volume.The synergistic effects of improved swept volume and oil displacement efficiency were the EOR mechanisms of the MCB nanoparticles.The studies indicate that these MCB nanoparticles have excellent potential for EOR in low permeability reservoirs.

Effects of Conductive Carbon Black on Thermal and Electrical Properties of Barium Titanate/Polyvinylidene Fluoride Composites for Road Application

In the field of roads,due to the effect of vehicle loads,piezoelectric materials under the road surface can convert mechanical vibration into electrical energy,which can be further used in road facilities such as traffic signals and street lamps.The barium titanate/polyvinylidene fluoride(BaTiO_(3)/PVDF)composite,the most common hybrid ceramic-polymer system,was widely used in various fields because the composite combines the good dielectric property of ceramic materials with the good flexibility of PVDF material.Previous studies have found that conductive particles can further improve the dielectric and piezoelectric properties of other composites.However,few studies have investigated the effect of conductive carbon black on the dielectric and piezoelectric properties of BaTiO_(3)/PVDF composites.In this study,BaTiO_(3)/PVDF/conductive carbon black composites were prepared with various conductive carbon black contents based on the optimum ratio of BaTiO_(3)to PVDF.The effects of conductive carbon black content on the morphologies,thermal performance,conductivities,dielectric properties,and piezoelectric properties of the BaTiO_(3)/PVDF/conductive carbon black composites were then investigated.The addition of conductive carbon black greatly enhances the conductivities,dielectric properties,and piezoelectric properties of the BaTiO_(3)/PVDF/conductive carbon black composites,especially when the carbon black content is 0.8%by weight of PVDF.Additionally,the conductive carbon black does not have an obvious effect on the morphologies and thermal stabilities of BaTiO_(3)/PVDF/conductive carbon black composites.

Highly Sensitive Electrochemical Detection of Nitrite Based on Cationic Surfactant Modification of Conductive Carbon Black

Nitrite is a commonly used additive in cured foods and its sensitive detection is important to human health.In this work,a simple but sensitive electrochemical sensor for nitrite was developed.Conductive carbon black(VXC-72R)functionalized with a cationic surfactant cetyltrimethylammonium bromide(CTAB)was used as an electrode material,and was coated on a glassy carbon electrode(GCE)to fabricate the electrochemical sensor(CTAB/VXC-72R/GCE)for nitrite.Zeta potential characterization and a series of electrochemical tests were carried out on several materials.It was found that the present sensor showed an enhanced sensitivity towards nitrite detection due to the enhanced surface positive charge revealed by the Zeta potential.Under optimal conditions,the ranges of good linear relationship between the peak current and the nitrite concentration were obtained to be 0.5-5.0μmol/L and 5.0-1087.0μmol/L with a lower detection limit of 0.30μmol/L.It was also successfully used for the determination of nitrite in cured food samples with excellent reproducibility,stability and selectivity.

Black Carbon Size in Snow of Chinese Altai Mountain in Central Asia

Black carbon(BC)in snow plays an important role to accelerate snow melting.However,current studies mostly focused on BC concentrations,few on their size distributions in snow which affected BC’s effect on albedo changes.Here we presented refractory BC(rBC)concentrations and size distributions in snow collected from Chinese Altai Mountains in Central Asia from November 2016 to April 2017.The results revealed that the average rBC concentrations were 5.77 and2.82 ng g-1for the surface snow and sub-surface snow,which were relatively higher in the melting season(April)than that in winter(November-January).The mass median volume-equivalent diameter of rBC size in surface snow was approximately at 120-150 nm,which was typically smaller than that in the atmosphere(about 200 nm for urban atmosphere).However,there existed no specific mass median volume-equivalent diameter of BC size for sub-surface snow in winter.While during the melting season,the median mass size of rBC in sub-surface snow was similar to that in surface snow.Backward trajectories indicated that anthropogenic sourced BC dominated rBC in snow(70%-85%).This study will promote our understanding on BC size distributions in snow,and highlight the possible impact of BC size on climate effect.

Correcting Black Carbon Absorption Measurements with Micro-aethalometer Model 200: Insights from Comparative Analysis

Black carbon(BC)is the strongest visible-light-absorbing aerosol component in the atmosphere,with a sig-nificant impact on Earth’s radiative budget.Accurate measurement of BC light absorption is crucial for estimating its radiative effect.The micro-aethalometer model 200(MA200)by AethLabs,USA,offers high-time-resolution measurement of the multi-wavelength absorption coefficient(σ_(ab))within 1 s,making it widely used in aerial measurement due to its compact size and light weight.However,the reliability of the measuredσ_(ab) has not been extensively studied in previous research.In this study,we evaluate the performance of MA200 by comparingσ_(ab) measurements obtained from MA200 with those from the aethalometer model 33(AE33)by Magee,USA.Our results revealed a significant variation in the determinant coefficient(R 2)betweenσ_(ab) measurements from MA200 and AE33,depending on the time resolution.The R 2 increases from 0.1 to 0.5 and further to 0.97 as the time resolution of σ_(ab) increases from 1 s to 30 s and 60 s,respectively.We recommend a minimum time resolution of 30 s for stableσ_(ab) measurements using MA200.Moreover,we determineσ_(ab) from attenuation coefficient(σ_(ATN))measured by MA200 asσ_(ab)=(σ_(ATN)-σ_(0))/C_( MA),whereσ_(0 )ranges from-15.3 Mm-1 to-6.4 Mm-1 and C MA ranges from 2.65 to 3.21.Correcting the measuredσ_(ab) based on the findings of this study can provide reliable results for estimating the radiative effects of BC.

Simulation of the Radiative Effect of Black Carbon Aerosols and the Regional Climate Responses over China

As part of the development work of the Chinese new regional climate model (RIEMS), the radiative process of black carbon (BC) aerosols has been introduced into the original radiative procedures of RIEMS, and the transport model of BC aerosols has also been established and combined with the RIEMS model. Using the new model system, the distribution of black carbon aerosols and their radiative effect over the China region are investigated. The influences of BC aerosole on the atmospheric radiative transfer and on the air temperature, land surface temperature, and total rainfall are analyzed. It is found that BC aerosols induce a positive radiative forcing at the top of the atmosphere (TOA), which is dominated by shortwave radiative forcing. The maximum radiative forcing occurs in North China in July and in South China in April. At the same time, negative radiative forcing is observed on the surface. Based on the radiative forcing comparison between clear sky and cloudy sky, it is found that cloud can enforce the TOA positive radiative forcing and decrease the negative surface radiative forcing. The responses of the climate system in July to the radiative forcing due to BC aerosols are the decrease in the air temperature in the middle and lower reaches of the Changjiang River and Huaihe area and most areas of South China, and the weak increase or decrease in air temperature over North China. The total rainfall in the middle and lower reaches of the Changjiang River area is increased, but it decreased in North China in July.

Black Carbon Particles in the Urban Atmosphere in Beijing

A study of the concentration of black carbon particles and its variation in the urban atmosphere has been carried out since 1996 in the Beijing area. The measurements were done in the late autumn and early winter each year, the period before and after domestic heating activities begin. The results show the presence of black carbon particles at the high level that vary over a large range in the urban atmosphere in Beijing. The mean value of daily average concentration for the whole observation period of 1996-2004 is 20.0 μgm^-3. An evident decrease of black carbon particle concentration in the Beijing area is observed after 2000, and the daily average concentration of black carbon particles is estimated to be 16.0 μgm^-3 with a variation range of 2.10-50.50 μgm^-3 for the period of 2000-2004. The observation method and main variation behavior characteristics of black carbon particles in the urban atmosphere in the Beijing area are given and discussed.

Soil Organic Carbon, Black Carbon, and Enzyme Activity Under Long-Term Fertilization

The present study aims to understand the effects of long-term fertilization on soil organic carbon （SOC）, black carbon （BC）, enzyme activity, and the relationships among these parameters. Paddy field was continuously fertilized over 30 yr with nine different fertilizer treatments including N, P, K, NP, NK, NPK, 2NPK （two-fold NPK）, NPK＋manure （NPKM）, and CK （no fertilization）, N, 90 kg urea-N ha^-1 yr^-1; P, 45 kg triple superphosphate-P205 ha^-1 yr^-1; K, 75 kg potassium chloride-K20 ha^-1 yr^-1; and pig manure, 22 500 kg ha^-1 yr^-1. Soil samples were collected and determined for SOC, BC content, and enzyme activity. The results showed that the SOC in the NPKM treatment was significantly higher than those in the K, P, and CK treatments. The lowest SOC content was found in the CK treatment. SOC content was similar in the N, NP, NK, NPK, 2NPK, and NPKM treatments. There was no significant difference in BC content among different treatments. The BC-to-SOC ratios （BC/SOC） ranged from 0.50 to 0.63, suggesting that BC might originate from the same source. Regarding enzyme activity, NPK treatment had higher urease activity than NPKM treatment. The urease activity of NPKM treatment was significantly higher than that of 2NPK, NP, N, P, K, CK, and NPKM treatment which produced higher activities of acid phosphatase, catalase, and invertase than all other treatments. Our results indicated that long-term fertilization did not significantly affect BC content. Concurrent application of manure and mineral fertilizers increased SOC content and significantly enhanced soil enzyme activities. Correlation analysis showed that catalase activity was significantly associated with invertase activity, but SOC, BC, and enzyme activity levels were not significantly correlated with one another. No significant correlations were observed between BC and soil enzymes. It is unknown whether soil enzymes play a role in the decomposition of BC.

Silver Supported on White Carbon Black Containing Rare Earths as Antibacterial Material

The antimicrobial effect of the Ag-White Carbon Black containing rare earth was investigated. Inorganic antibiotic materials consist of the antibacterial ion, the additive and the carrier. The sol-gel method was used to prepare the white carbon black carrier. Ag+ was selected to be the antibacterial ion, and cerous nitrate was selected to be the additive. They were synthesized on the white carbon black carrier. The structures and properties of antibacterial material were characterized by inductively coupled plasma, particle size measurement instrument, fourier transform infrared and enumeration tests (Escherichia coli as experimental bacterium). Results showed that the amount of antibacterial ions and bacteriostasis rate of this new material are higher than those for the general Ag-antibacterial white carbon black (without containing rare earth). Ag+ was bound to white carbon black by ion exchange process and adsorption process. Bacteriostasis rate is over 99%, and the particle size can be extended down to 7 μm with a narrow size distribution. Other advantages of this material are good thermal and light stability. Furthermore, from the antibacterial experiment in rubber and the coating surface of metal, this new material showed promising results. The possible antibacterial mechanism was also proposed through all the experimental data in this study.

Investigation of reinforcement of the modified carbon black from wasted tires by nuclear magnetic resonance

Pyrolysis has the potential of transforming waste into recyclable products. Pyrolytic carbon black (PCB) is one of the most important products from the pyrolysis of used tires. Techniques for surface modifications of PCB have been developed. One of the most significant applications for modified PCB is to reinforce the rubber matrix to obtain high added values. The transverse relaxation and the chain dynamics of vulcanized rubber networks with PCB and modified PCB were studied and compared with those of the commercial carbon blacks using selective 1H transverse relaxation (T2) experiments and dipolar correlation effect (DCE) experiments on the stimulated echo. Demineralization and coupling agent modification not only intensified the interactions between the modified PCB and the neighboring polyisoprene chains, but also increased the chemical cross-link density of the vulcanized rubber with modified PCB. The mechanical testing of the rubbers with different kinds of carbon blacks showed that the maximum strain of the rubber with modified PCB was improved greatly. The mechanical testing results confirmed the conclusion obtained by nuclear magnetic resonance (NMR). PCB modified by the demineralization and NDZ-105 titanate coupling agent could be used to replace the commercial semi-reinforcing carbon black.

INFLUENCES OF MODIFIERS ON SURFACE PROPERTIES OF WHITE CARBON BLACK AND MECHANICAL PROPERTIES OF SILICONE RUBBER

Various of modifiers were used to modify the surface activity of white carbon black. The oil absorption, viscosity, hydrophobic rate and burning loss of white carbon black and the mechanical propertiess of silicone rubber were measured. The influences of the modifiers on the properties of white carbon black and the mechanical properties of silicone rubber were discussed.

Influence of Water Content on Conductivity and Piezoresistivity of Cement-based Material with both Carbon Fiber and Carbon Black

The influence of water content on the conductivity and piezoresistivity of cement-based material with carbon fiber （CF） and carbon black （CB） was investigated. The piezoresistivity of cement-based material with both CF and CB was compared with that of cement-based material with CF only, and the changes in electrical resistivity of cement-based material with both CF and CB under static and loading conditions in different drying and soaking time were studied. It is found that the piezoresistivity of cement-based material with both CF and CB has better repeatability and linearity than that of cement-based material with CF only. The conductivity and the sensitivity of piezoresistive cement-based material with both CF and CB are enhanced as the water content in piezoresistive cement-based material increases.

Preparation and Properties of Rare Earth Modified Carbon Black/Natural Rubber Composites

The oxides Eu, Ho, Er and Dy were used to prepare the hydroxides of rare earth modified carbon black. Then natural rubber latex （NRL） was added into the reactor. The system reacted at 85 ℃ with stirring for 1 h to prepare powdered HAF-Ln（OH）3/NR composites. The effects of the kind and content of Ln on the particle size distribution of P [ NR/HAF-Ln （OH）3 ] and mechanical properties of its vulcanizate were studied respectively. It is found that rare earth can help to get the powder of the composite, the product particle with a diameter less than 0.9mm will be get when the composites containing the compound of Ho, Er and Dy with dosage of 1.0, 1.0, O. 5 percent, respectively. The adding of Ln can improve the tensile strength and tear strength of the vulcanizate effectively, what＇s more, Er and Dy can decrease the permanent set of vulcanizate significantly. The SEM studies shows that P[ NR/HAF-Dy （OH）3 ] vulcanizate shows superior mechanical properties that depend primarily on the absence of free carbon black, the fine dispersion of carbon black in the rubber matrix and better polymer-filler interaction.

Radiative Forcing and Climate Response Due to Black Carbon in Snow and Ice

The radiative forcing and climate response due to black carbon（BC） in snow and/or ice were investigated by integrating observed effects of BC on snow/ice albedo into an atmospheric general circulation model（BCC AGCM2.0.1） developed by the National Climate Center（NCC） of the China Meteorological Administration（CMA）.The results show that the global annual mean surface radiative forcing due to BC in snow/ice is ＋0.042 W m 2,with maximum forcing found over the Tibetan Plateau and regional mean forcing exceeding ＋2.8 W m 2.The global annual mean surface temperature increased 0.071 C due to BC in snow/ice.Positive surface radiative forcing was clearly shown in winter and spring and increased the surface temperature of snow/ice in the Northern Hemisphere.The surface temperatures of snow-covered areas of Eurasia and North America in winter（spring） increased by 0.83 C（0.6 C） and 0.83 C（0.46 C）,respectively.Snowmelt rates also increased greatly,leading to earlier snowmelt and peak runoff times.With the rise of surface temperatures in the Arctic,more water vapor could be released into the atmosphere,allowing easier cloud formation,which could lead to higher thermal emittance in the Arctic.However,the total cloud forcing could decrease due to increasing cloud cover,which will offset some of the positive feedback mechanism of the clouds.

Enhancement of the formic acid electrooxidation activity of palladium using graphene/carbon black binary carbon supports

Combinations of graphene(Gr)and carbon black(C)were employed as binary carbon supports to fabricate Pd‐based electrocatalysts via one‐pot co‐reduction with Pd2+.The electrocatalytic performance of the resulting Pd/Gr‐C catalysts during the electrooxidation of formic acid was assessed.A Pd/Gr0.3C0.7(Gr oxide:C=3:7,based on the precursor mass ratio)electrocatalyst exhibited better catalytic performance than both Pd/C and Pd/Gr catalysts.The current density generated by the Pd/Gr0.3C0.7catalyst was as high as102.14mA mgPd?1,a value that is approximately3times that obtained from the Pd/C(34.40mA mgPd?1)and2.6times that of the Pd/Gr material(38.50mA mgPd?1).The anodic peak potential of the Pd/Gr0.3C0.7was120mV more negative than that of the Pd/C and70mV more negative than that of the Pd/Gr.Scanning electron microscopy images indicated that the spherical C particles accumulated on the wrinkled graphene surfaces to form C cluster/Gr hybrids having three‐dimensional nanostructures.X‐ray photoelectron spectroscopy data confirmed the interaction between the Pd metal and the binary Gr‐C support.The Pd/Gr0.3C0.7also exhibited high stability,and so is a promising candidate for the fabrication of anodes for direct formic acid fuel cells.This work demonstrates a simple and cost‐effective method for improving the performance of Pd‐based electrocatalysts,which should have potential industrial applications.

Black carbon and polycyclic aromatic hydrocarbons (PAHs) in surface sediments of China’s marginal seas

This study investigates the distribution of black carbon （BC） and its correlation with total polycyclic aromatic hydrocarbons （EPAH） in the surface sediments of China＇s marginal seas. BC content ranges from 〈0.10 to 2.45 mg/g dw （grams dry weight） in the sediments studied, and varied among the different coastal regions. The Bohai Bay sediments had the highest BC contents （average 2.18 mg/g dw）, which comprises a significant fraction （27%-41%） of the total organic carbon （TOC） preserved in the sediments. In comparison, BC in the surface sediments of the North Yellow Sea, Jiaozhou Bay, East China Sea and the South China Sea is less abundant and accounted for an average of 6%, 8%, 14% and 5%, respectively, of the sedimentary organic carbon pool. The concentration of EPAH in the surface sediments ranges from 41 to 3 667 ng/g dw and showed large spatial variations among the sampling sites of different costal regions. The Bohai Bay has the highest ZPAH values, ranging from 79 to 3 667 ng/g dw. This reflects the high anthropogenically contaminated nature of the sediments in the bay. BC is positively correlated to TOC but a strong correlation is not found between BC and ZPAH in the surface sediments studied, suggesting that BC and PAHs preserved in the sediments are derived from different sources and controlled by different biogeochemical processes. Our study suggests that the abundance of BC preserved in the sediments could represent a significant sink pool of carbon cycling in China＇s marginal seas.

Pseudo-capacitance of ruthenium oxide/carbon black composites for electrochemical capacitors

Hydrous ruthenium oxide was formed by a new process. The precursor was obtained by mixing the aqueous solutions of RuCl3xH2O and NaHCO3. The addition of NaHCO3 led to the formation of an oxide with extremely fine RuO2 particles forming a porous network structure in the oxide electrode. Polyethylene glycol was added as a controller to partly inhibit the sol-gel reaction. The rate capacitance of 530 F·g^-1 was measured for the powder formed at an optimal annealing temperature of 210℃. Several details concerning this new material, including crystal structure, particle size as a function of temperature, and electrochemical properties, were also reported. In addition, the rate capacitance of the composite electrode reached 800 F·g^-1 after carbon black was added. By using the modified electrode of a RuO2/carbon black composite electrode, the electrochemical capacitor exhibits high energy density and stable power characteristics. The values of specific energy and maximum specific power of 24 Wh·kg^-1 and 4 kW·kg^-1, respectively, are demonstrated for a cell voltage between 0 and 1 V.