Investigation of the effect of diethylene triamine pentaacetic acid chelating agent as an enhanced oil recovery fluid on wettability alteration of sandstone rocks

This study used the diethylene triamine pentaacetic acid(DTPA)-seawater(SW)system to modify the sandstone rock wettability and enhance oil recovery.The investigation involved conducting wettability measurement,Zeta potential measurement,and spontaneous imbibition experiment.The introduction of 5%DTPA-sW solution resulted in a significant decrease in the rock-oil contact angle from 143°to 23,along with a reduction in the Zeta potential from-2.29 mV to-13.06 mV,thereby altering the rock surface charge and shifting its wettability from an oil-wet state to a strongly water-wet state.The presence or absence of potential determining ions(Ca^(2+),Mg^(2+),SO_(4)^(2-))in the solution did not impact the effectiveness of DTPA in changing the rock wettability.However,by tripling the concentration of these ions in the solution,the performance of 5%DTPA-SW solution in changing wettability was impaired.Additionally,spontaneous imbibition tests demonstrated that the 5%DTPA-SW solution led to an increase in oil recovery up to 39.6%.Thus,the optimum mass fraction of DTPA for changing sandstone wettability was determined to be5%.

Effect of Combined Treatments of Phytohormones and Chelating Agents on the Accumulation Capacity of Amaranth

[Objective] To explore a high efficient phytoremediation technology for soil pollution. [Method] Foliage application and root irrigation were carried out to study the influence on amaranth repair efficiency by using combined treatments of phytohor- mones （IAA, GA3 SA） and chelating agents （EDTA）. [Result] The combined treatment increased the biomass of amaranth under 133Cs, 88Sr, Cr stress The 133Cs, 88Sr, Cr enrich- ment in amaranth by root irrigation were obviously higher than that by foliage appli- cation. The phytoextraction efficiency of phytohormones and chelating agents from best to poor was as following： 100 mg/L SA＋1.5 mg/kg EDTA, 500 mg/L GA3＋1.5 mg/kg EDTA, 100 mg/L IAA＋1.5 mg/kg EDTA. [Conclusion] The most appropriate treatment was the combined treatment of 100 mg/L SA＋l.5mg/kg EDTA by soil irri- gation, which could make the total absorption doses of 133Cs, 88Sr, Cr per plant achieve the maximum.

The effect of chelating agent on hydrodesulfurization reaction of ordered mesoporous alumina supported Ni Mo catalysts

In this paper,ordered mesoporous alumina(OMA)support with the high surface area(328 m^(2)g^(-1))and the large pore volume 0.74(cm^(3)·g^(-1))was synthesized by homogeneous precipitation method.And the influence of EDTA on the physical and chemical properties of the modified catalysts was also studied.The characteristic results showed that the addition of EDTA could adjust the metal-support interaction and improved the acidity of the corresponding catalyst.Combined with the catalytic performance results,the EDTA-modified Ni Mo E(1.0)/OMA catalyst displays the highest DBT hydrodesulfurization conversion(97.7%).

Effect of chelating agent on oxidation rate of aniline in ferrous ion activated persulfate system at neutral pH

In the interest of accelerating aniline degradation, Fe2+ and chelated Fe2+ activated persulfate oxidations were investigated in neutral pH condition. Three kinds of chelating agents were selected including citric acid, oxalic acid and ethylenediamine tetraaceatate(EDTA) to maintain available Fe2+. The results indicate that the concentration of chelating agent and ferrous ion didn't follow a linear relationship with the degradation rate of aniline. A 1/1 ratio of chelating agent/Fe2+ results in a higher degradation rate compared to the results by other ratios. The oxidation enhancement factor using oxalic acid was found to be relatively low. In contrast, citric acid is more suitable chelating agent in the ferrous iron activated persulfate system and aniline exhibits a highest degradation with a persulfate/Fe2+/citric acid/aniline molar ratio of 50/25/25/1 compared to other molar ratios.

Effect of the chelating agents on bio-sorption of hexavalent chromium using Agave sisalana fibers

The current work is focused on the study of the bio-sorption of hexavalent chromium from aqueous solution using sisal natural fiber(Agave sisalana) treated by various chelating agents(ligands) such as urea(UR),thiocarbamide(TC), ethylenediaminetetraacetic acid(EDTA), and diphenyl carbazide(DCZ). The fiber treatments were investigated using Fourier Transform Infrared Spectroscopy(FTIR) and Scanning electron microscope(SEM). The kinetics of chromium bio-sorption was studied in batch presses under the effect of some physicochemical factors such as the nature of chelating agent(F@UR, F@TC, F@DCZ, and F@EDTA),adsorbent dose(2–10 g·L^(-1)), chromium initial concentration(100–500 mg·L^(-1)), solution pH(1–6), and batch temperature(20 ℃–50 ℃). This study resulted in an optimum adsorption at a chromium initial concentration of 100 mg·L^(-1), at pH 2, and at 20 ℃. The obtained results showed clearly that the treatment with chelating agent boosts the adsorptive capacity of A. sisalana fibers Cr(VI) 10.9 mg·g^(-1) to 58.6 mg·g^(-1). The modeling study showed that the adsorption kinetics obey the pseudo-second-order model, with an R2 in the range of 0.991 and 0.999. The bio-sorption isotherms followed the Langmuir model; the maximum uptake capacity of(F@N, F@UR,F@TC, F@DCZ, and F@EDTA) was found to be respectively, 12.3 mg·g^(-1), 25.33 mg·g^(-1), 28.73 mg·g^(-1),42.54 mg·g^(-1), and 61.45 mg·g^(-1). The determined adsorption thermodynamics parameters such as enthalpy,free energy, and entropy showed that the adsorption process is exothermic, spontaneous, and has a stable configuration.

Influence of Different Chelating Agents on Corrosion Performance of Microstructured Hydroxyapatite Coatings on AZ91D Magnesium Alloy

To improve the bioactivity and corrosion resistance of AZ91 D magnesium alloy,hydroxyapatite（HAp） coatings with novel microstructured morphologies were prepared successfully on AZ91 D substrates via a facile hydrothermal method.Different chelating agents including polyaspartic acid（PASP） and ethylenediaminetetraacetic acid（EDTA） were introduced to investigate their effects on the morphology and corrosion resistance of the coated magnesium alloys.The results revealed that the coating prepared with PASP was composed of many uniform urchin-like microspheres,while the coating prepared with EDTA consisted of many flower-like particles.Moreover,the crystallinity of the coating prepared with EDTA was much higher than that of the coating prepared with PASP.Electrochemical tests revealed that the corrosion resistance of the substrate was significantly improved after being coated with each coating.Immersion test of the coated samples in simulated body fluid（SBF） demonstrated that the coatings could be biodegraded gradually and induce the formation of calcium phosphate particles.

Removal of As and Heavy Metals （Cd, Cu and Pb） in Fine Soil from Soil Washing Process Using Chelating Agent

Fine soil generated from the soil washing process can be the second problem, as contaminants are concentrated in the fine soil, and also took the difficult forms to treat because soluble and exchangeable fractions are already removed by soil washing process; therefore, the fine soil is indicated to hazardous waste, and discarded in hazardous waste landfill. Thus, this research would be performed that arsenic and heavy metals formed difficult to remove in the fine soil were converted to more treatable fractions with chelating agents. Moreover, feasibility study to apply the second remediation targeted to the fine soil inquired. As a result, the chelating agent was decided 50 mM Na2EDTA, and it could develop the complex. In addition, the result of sequential extraction showed that Mn/Fe-oxide fraction, comprised about 28% of amount at first, was decreased about 16%, and organic fraction, consisted approximately 20%, was also decreased about 11%, while exchangeable fraction and carbonate fraction were increased. This result means that the difficult fractions removed could change fractions） by chelating agent. This research can provide the possibility hazardous waste because of difficulty to remediate. the more treatable fractions （exchangeable and carbonate to treat the fine soil, although the fine soil was regarded to

Influence of Chelating Agents on Chromium Fate in Sediment

A laboratory investigation on reaction between chelating agents and chromium was conducted to evaluate the effect of chelating agents on the adsorption and desorption of chromium in sediment. The amount of adsorbed chromium(VI) in sediment decreased slightly by 5%-10% because of addition of chelating agents.Chelating agents inhibited the remodel of Cr(Ⅲ) by sediment from solutions and the inhibiting effect was in the order:citric acid > tartaric acid > EDTA, salicylic acid.No effect of chelating agents on desorption of chromium in sediment was observed.

SYNERGISTIC ACTIVATION OF CHELATING AGENT ON XANTHATE DURING THE FLOTATION OF REFRACTORY COPPER OXIDIZED ORES

For realizing the effective flotation of refractory copper ox-idized ores and developing the activation-flotation theory , the influences of nine different organic chelating agents on xanthate collection pcnver and its adsorption characteristics ivere studied in the flotation of malachite and chrysocolla representatively selected by means of XPS,IR, absorbed quanti-ty measurements and flotation tests.For easily-dissolved malachite flotation , a small amount of chelating agent can obviously enhance xanthate collecting power and make malachite floated easily , and so reduces the consumption of xanthate. For hard-dis-晄olved chrysocolla, chelating agent is able to increase its recovery to 90% , but the chelating agent consumption is high. Chelating agent and xanthate can produce synergistic adsorptions, which follmv Freundlich's adsorption equation on malachite and Chrysocolla surfaces. The high chemical activity of chelating agent and its synergistic activation on xanthate are the key to improving xanthate collection poiver. The synergistic activation of chelat-ing agent on xanthate on melachite surfaces is clearly stronger than on chrysocolla surfaces. According to experimental results, it can be thought that the synergistic activation results from the synergistic complexation of chelating agent and xanthate with copper ions to form biligand-tribasic co-ordination complex.

IMPROVEMENT OF BLEACHING OF KAOLIN USING CHELATING AGENTS

Bleaching of the kaolin ore from Shaziling Kaolin Mine in Jiangxi Province of China was studied with the aim of enhancing the quality and value of the ore to meet the requirements from the ceramics manufacturers. Factors affecting the reductive bleaching of kaolin ore with sodium dithionite as the bleaching agent were studied and optimized to increase the whiteness of the kaolin ore from 38. 5% to about 65%. However, it was found that in the conventional bleaching process, a washing step to remove the ferrous ions from the bleached kaolin suspension was indispensable, which made the process complicated and restricted the capacity of the production. In addition, the whiteness of the bleached kaolin products was unstable. To solve the above problems, a new technique with the application of chelating agents in the bleaching process was developed to remove ferrous ions and get rid of the washing step. The bleaching process of kaolin was simplified. The whiteness of the bleached kaolin products was stabilized as well as increased to about 70%. The mechanism of the bleaching process and the action of the chelating agents were discussed.

A feasibility study on cleaning Pb-contaminated soil with chelating agents

In this paper, the complexing abilities of EDTA, TTHA and Cit. with lead in the Pb(2.59 mg/g) contaminated soil were compared in the laboratory. Possibilities for lead and the threeagents to develop stable complexes increased proportionally to the growth of lead complexible formwhen the PH values ranged between 4 and 6. Under acid conditions, logB_(Pb-TTHA)) valued as 28.1 wasmuch higher than logB_(Pb-EDTA), as 18.0 depending on producing Pb_2-TTHA (logK_(Pb_2-TTHA= 11 0) andPb-HTTHA (logK(Pb-HTTTHA)=8.2)). Conclusively, the complexing ability of TTHA with Pb still ex-aseded that of EDTA by about 10% even when the amount of TTHA added was only equal to onefourth of that of EDTA. Due to the lower cost and less harzn to crops, Cit. can still be taken as abetter chelating agent in acid soil although its coordinative capability with Pb was weaker thanEDTA and TTHA.

STUDIES ON THE COMPETITION FOR CADMIUM ION BETWEEN CHELATING AGENTS AND BOVINE SERUM ALBUMIN

Eleven chelating agents were studied for their capabilities to mobilize the cadmium bound tp bovine serum albumin(BSA).The parameter F,which is defined as the ratio between the percentages of cadmium bound to BSA in the presence and absence of chelating agents,can be used as the criterion to evaluate the mobilizing capability of chelating agent.The F values determined experimentally lead to a mobilizing capability order:DTPA>EDTA>EGTA>NTA>TR1EN>PEN>CYS>HIS>SAThe polyaminopolycarboxylate type chelators mobilize cadmium effectively.A linear relationship was found between 1gF and lg k'CdL (conditional stability constant of the cadmium chelate).

Catechol-Bisphosphonate Conjugates: New Potential Chelating Agents for Metal Intoxication Therapy

In a quest for better chelating therapy drugs for the treatment of intoxication by Fe, Al, oractinides, two new series of mixed catechol-bisphosphonate through amide linkage were synthesized.Benzyl group was used as protecting group to avoid the breakage of amide by acid hydrolysis orimcomplete reaction in silylation-dealkylation using bromotrimethylsilane.

A NEW BIFUNCTIONAL CHELATING AGENT α,ε-N,N'-BIS(L-CYSTEINYL)-L-LYSINE FOR RADIOLABELLING OF MONOCLONAL ANTIBODIES WITH TECHNETIUM-99M

α,ε-N,N'-bis(L-cysteinyl)-L-lysine was synthesized and char- acterized for the first time.It was then employed as a bifunctional chelating agent to chelate technetium-99m and subsequently conjugated to fragment F(ab')_2 of anti-gastric tumor monoclonal antibody 3G9.The radiolabelled antibody was satisfactorily stable and immunoreactive.

Study on Treatment of Heavy Metals in Fly Ash by a Chelating Agent

The fly ash from two municipal solid waste incineration plants in Shanghai was treated by the self-developed organic composite chelating agent. The results indicated that the stabilization effect of Pb in the fly ash by the composite chelating agent was the best,and the proportions of its easily leaching form in the two kinds of fly ash decreased from 29. 60% and 27. 49% to 3. 05% and 0. 29% respectively. The leaching toxicity of stabilized fly ash was lower than the limits of Standard for Pollution Control on the Landfill Site of Municipal Solid Waste（ GB 16889- 2008）,so it can be landfilled separately in the landfill site of municipal solid waste.

Pore-scale study of the effects of DTPA chelating agent flooding on oil recovery utilizing a clay-coated micromodel

The use of diethylenetriaminepentaacetic acid(DTPA)chelating agent has shown promising results for enhanced oil recovery(EOR)in prior research.Several mechanisms,mainly resulting from rock-fluid interaction,have been proposed for chelating agent flooding;however,little attention has been paid to fluid-fluid interaction thus far.The assessment of these mechanisms has primarily relied on macroscopic techniques such as core flooding.This paper aims to investigate the injection of DTPA brine and its dominant mechanisms at the pore scale using a clay-coated micromodel.The micromodel tests were performed under oil-wet and water-wet states.For a more precise examination of fluid/fluid interactions,the dynamic interfacial tension(IFT)and Zeta potential were measured.It was observed that the injection of DTPA brine in water-wet state changed the saturation distribution and increased oil recovery.Based on visual inspections,this change in saturation distribution could potentially be linked to the formation of micro-dispersions and viscoelastic interfacial phenomena.Micro-dispersions facilitate flow to unswept areas,and viscoelastic interface formation reshapes the interface between oil and brine,causing disconnected oil droplets to coalesce and thus increase recovery.Under the oil-wet state,the micro-dispersion formation and wettability alteration can be the dominant mechanisms,and the amount of recovered oil was higher than that observed in the water-wet state.Furthermore,Zeta potential measurements at the interface between brine and oil showed a more negative value for DTPA brine,which is effective in wettability alteration and micro-dispersions stability.The results indicate that IFT reduction was not significant enough to be considered the dominant mechanism,although it assists in DTPA brine penetration into the crude oil and subsequent micro-dispersion formation.

Influence of pH value and chelating reagent on performance of Li_3V_2(PO_4)3/C cathode material

The Li3V2（PO4）3/C composite cathode material was synthesized via sol-gel method using three different chelating agents （citric acid, salicylic acid and polyacrylic acid） at pH value of 3 or 7. The crystal structure, morphology, specific surface area and electrochemical performance of the prepared samples were investigated by X-ray diffraction （XRD）, scanning electron microscopy （SEM）, cyclic voltammetry （CV）, electrochemical impedance spectroscopy （EIS） and galvanostatic charge/discharge test. The results show that the effects of pH value on the performance of the prepared materials are greatly related to the chelating agents. With salicylic acid or polyacrylic acid as the chelating reagent, the structure, morphology and electrochemical performance of the samples are greatly influenced by the pH values. However, the structure of the materials with citric acid as the chelating agent does not change as pH value changes, and the materials own uniform particle size distribution and good electrochemical performance. It delivers an initial discharge capacity of 113.58 mA·h/g at 10C, remaining as high as 108.48 mA·h/g after 900 cycles, with a capacity retention of 95.51%.

Application of a macromolecular chelating agent in chemical mechanical polishing of copper film under the condition of low pressure and low abrasive concentration

The mechanism of the FA/O chelating agent in the process of chemical mechanical polishing （CMP） is introduced. CMP is carried on a φ300 mm copper film. The higher polishing rate and lower surface roughness are acquired due to the action of an FA/O chelating agent with an extremely strong chelating ability under the condition of low pressure and low abrasive concentration during the CMP process. According to the results of several kinds of additive interaction curves when the pressure is 13.78 kPa, flow rate is 150 mL/min, and the rotating speed is 55/60 rpm, it can be demonstrated that the FA/O chelating agent plays important role during the CMP process.

Chelating agents role on phase formation and surface morphology of single orthorhombic YMn_2O_5 nanorods via modified polyacrylamide gel route

YMn2O5nanorods were synthesized through a modified polyacrylamide gel route.The synthesis strategy in this work is based on a sol-gel process using a polyacrylamide gel method in which oxalic acid,citric acid or tartaric acid is employed as the chelating agent.In the gel routes,oxalic acid was used as a carboxyl chelating agent,while citric acid or tartaric acid was a carboxyl and hydroxyl chelating agent.The as-prepared samples were characterized by means of techniques such as X-ray powder diffraction(XRD)measurement,thermogravimetric analysis(TG),differential scanning calorimetry analysis(DSC),Fourier transform infrared spectroscopy(FTIR),X-ray photoelectron spectroscopy(XPS),thermal expansion measurement and field-emission scanning electron microscopy(SEM)investigations.It was found that oxalic acid is the best chelating agent with Y(NO3)3·6H2O and Mn(CH3COO)2·4H2O as precursors to prepare a single orthorhombic YMn2O5nanorods at 1000°C.Scanning electron microscope observation shows that the morphology of YMn2O5powders is significantly dependent on the chelating agent.The peaks(single orthorhombic YMn2O5nanorods)at 642,600,573,546,521,493,486,468,448 and 400cm?1were observed from FTIR spectra.The phase,surface morphology and chelation mechanisms of YMn2O5samples have been discussed on the basis of the experimental results.

Synergetic effect of chelating agent and nonionic surfactant for benzotriazole removal on post Cu-CMP cleaning

The cleaning of copper interconnects after chemical mechanical planarization （CMP） process is a crit- ical step in integrated circuits （ICs） fabrication. Benzotriazole （BTA）, which is used as corrosion inhibitor in the copper CMP slurry, is the primary source for the formation of organic contaminants. The presence of BTA can degrade the electrical properties and reliability of ICs which needs to be removed by using an effective cleaning solution. In this paper, an alkaline cleaning solution was proposed. The alkaline cleaning solution studied in this work consists of a chelating agent and a nonionic surfactant. The removal of BTA was characterized by contact angle measurements and potentiodynamic polarization studies. The cleaning properties of the proposed cleaning solution on a 300 mm copper patterned wafer were also quantified, total defect counts after cleaning was studied, scanning electron microscopy （SEM） review was used to identify types of BTA to confirm the ability of cleaning solution for BTA removal. All the results reveal that the chelating agent can effectively remove the BTA residual, nonionic surfactant can further improve the performance.