Edge effect during microwave plasma chemical vapor deposition diamond-film:Multiphysics simulation and experimental verification

This study focused on the investigation of the edge effect of diamond films deposited by microwave plasma chemical vapor de-position.Substrate bulge height△h is a factor that affects the edge effect,and it was used to simulate plasma and guide the diamond-film deposition experiments.Finite-element software COMSOL Multiphysics was used to construct a multiphysics(electromagnetic,plasma,and fluid heat transfer fields)coupling model based on electron collision reaction.Raman spectroscopy and scanning electron microscopy were performed to characterize the experimental growth and validate the model.The simulation results reflected the experimental trends observed.Plasma discharge at the edge of the substrate accelerated due to the increase in△h(△h=0-3 mm),and the values of electron density(n_(c)),molar concentration of H(C_(H)),and molar concentration of CH_(3)(C_(CH_(3)))doubled at the edge(for the special concave sample with△h=−1 mm,the active chemical groups exhibited a decreased molar concentration at the edge of the substrate).At=0-3 mm,a high diamond growth rate and a large diamond grain size were observed at the edge of the substrate,and their values increased with.The uniformity of film thickness decreased with.The Raman spectra of all samples revealed the first-order characteristic peak of dia-mond near 1332 cm^(−1).When△h=−1 mm,tensile stress occurred in all regions of the film.When△h=1-3 mm,all areas in the film ex-hibited compressive stress.

Fabrication of Graphene/Cu Composite by Chemical Vapor Deposition and Effects of Graphene Layers on Resultant Electrical Conductivity

Graphene(Gr)has unique properties including high electrical conductivity;Thus,graphene/copper(Gr/Cu)composites have attracted increasing attention to replace traditional Cu for electrical applications. However,the problem of how to control graphene to form desired Gr/Cu composite is not well solved. This paper aims at exploring the best parameters for preparing graphene with different layers on Cu foil by chemical vapor deposition(CVD)method and studying the effects of different layers graphene on Gr/Cu composite’s electrical conductivity. Graphene grown on single-sided and double-sided copper was prepared for Gr/Cu and Gr/Cu/Gr composites. The resultant electrical conductivity of Gr/Cu composites increased with decreasing graphene layers and increasing graphene volume fraction. The Gr/Cu/Gr composite with monolayer graphene owns volume fraction of less than 0.002%,producing the best electrical conductivity up to59.8 ×10^(6)S/m,equivalent to 104.5% IACS and 105.3% pure Cu foil.

Modification of ACFs by chemical vapor deposition and its application for removal of methyl orange from aqueous solution

Viscose activated carbon fibers （ACFs） were characterized using specific surface area, scanning electron modified with chemical vapor deposition （CVD）. The samples were microscopy （SEM）, pore size distribution and Fourier transform infrared spectroscopy （FTIR）. Batch adsorption experiments were carried out to investigate the adsorption behavior of modified ACFs for methyl orange（MO） from its aqueous solutions. The results show that the adsorption isotherms of MO onto modified ACFs well follows the Langmuir isotherm equation. The adsorption kinetics of MO can be well described by the pseudo second-order kinetic model. The adsorption process involves the intra-particle diffusion, but is not the only rate-controlling step. Thermodynamic parameters including AG, AH and AS were calculated, suggesting that the adsorption of MO onto modified ACFs is a spontaneous, exothermic and physisorption process. FTIR result indicates that the major adsorption mechanism of modified ACFs for MO is hydrogen bond.

Si-doped diamond films prepared by chemical vapour deposition

The effects of Si doping on morphology, components and structure characteristics of CVD diamond films were studied. Si-doped CVD diamond films were deposited on Si substrate by adding tetraethoxysilane （TEOS） into acetone as source of reactant gas. The morphology and microstructure of diamond films were characterized by scanning electron microcopy （SEM）. The crystalline quality of diamond films was studied by Raman spectroscopy and X-ray diffractometry （XRD）. The surface roughness of the films was evaluated with surface profilometer. The results suggest that Si doping tends to reduce the crystallite size, enhance grain refinement and inhibit the appearance of （11 I） facets. Raman spectra indicate that Si doping can enhance the formation of sp2 phase in diamond films. Moreover, Raman signal of SiC was detected, which suggests the existence of Si in the diamond films. Smooth fine-grained diamond （SFGD） film was synthesized at Si to C ratio of 1%.

Low-Temperature Growth of ZnO Films on GaAs by Metal Organic Chemical Vapor Deposition

ZnO thin films were grown on GaAs （001） substrates by metal-organic chemical vapor deposition （MOCVD） at low temperatures ranging from 100 to 400℃. DEZn and 1-12 O were used as the zinc precursor and oxygen precursor, respectively. The effects of the growth temperatures on the growth characteristics and optical properties of ZnO films were investigated. The X-ray diffraction measurement （XRD） results indicated that all the thin films were grown with highly c- axis orientation. The surface morphologies and crystal properties of the films were critically dependent on the growth temperatures. Although there was no evidence of epitaxial growth, the scanning electron microscopy （SEM） image of ZnO film grown at 400℃ revealed the presence of ZnO microcrystallines with closed packed hexagon structure. The photoluminescence spectrum at room temperature showed only bright band-edge （3. 33eV） emissions with little or no deep-level e- mission related to defects.

Disproportionation of Toluene by Modified ZSM-5 Zeolite Catalysts with High Shape-selectivity Prepared Using Chemical Liquid Deposition with Tetraethyl Orthosilicate

Shape-selective catalysts for the disproportionation of toluene were prepared by the modification of the cylinder-shaped ZSM-5 zeolite extrudates with chemical liquid deposition with TEOS （tetraethyl orthosilicate）.Various parameters for preparing catalysts were changed to investigate the suitable conditions.The resulting cata-lysts were tested in a pressured fixed bed reactor and characterized by SEM （scanning electron microscopy）.The conversion of toluene and para-xylene selectivity were influenced remarkably by the n（SiO2）/n（Al2O3） ratio of ZSM-5 zeolite,the type and amount of deposition agent,acid and solvent used,and the time and cycle of deposition treatment.TEOS was proved to be a more efficient agent than the conventional polysiloxanes when the deposition amount was low.The catalyst prepared at the suitable conditions exhibited a high para-xylene selectivity of 91.1% with considerable high conversion of 25.6%.SEM analyses confirmed the formation of a layer of amorphous silica on the external surface of ZSM-5 zeolie crystals,which was responsible for the highly enhanced shape-selectivity.

Two Step Chemical Vapor Deposition of In2Se3/MoSe2 van der Waals Heterostructures

Two-dimensional transition metal dichalcogenides heterostructures have stimulated wide in- terest not only for the fundamental research, but also for the application of next generation electronic and optoelectronic devices. Herein, we report a successful two-step chemical vapor deposition strategy to construct vertically stacked van der Waals epitaxial In2Se3/MoSe2 heterostructures. Transmission electron microscopy characterization reveals clearly that the In2Se3 has well-aligned lattice orientation with the substrate of monolayer MoSe2. Due to the interaction between the In2Se3 and MoSe2 layers, the heterostructure shows the quench- ing and red-shift of photoluminescence. Moreover, the current rectification behavior and photovoltaic effect can be observed from the heterostructure, which is attributed to the unique band structure alignment of the heterostructure, and is further confirmed by Kevin probe force microscopy measurement. The synthesis approach via van der Waals epitaxy in this work can expand the way to fabricate a variety of two-dimensional heterostructures for potential applications in electronic and optoelectronic devices.

Technical Challenges and Progress in Fluidized Bed Chemical Vapor Deposition of Polysilicon

Various methods for production of polysilicon have been proposed for lowering the production cost andenergy consumption, and enhancing productivity, which are critical for industrial applications. The fluidized bed chemical vapor deposition （FBCVD） method is a most promising alternative to conventional ones, but the homogeneous reaction of silane in FBCVD results in unwanted formation of fines, which will affect the product qualityand output. There are some other problems, such as heating degeneration due to undesired polysilicon deposition on the walls of the reactor and the heater. This article mainly reviews the technological development on FBCVD of polycrystalline silicon and the research status for solving the above problems. It also identifies a number of challenges to tackle and principles should be followed in the design ofa FBCVD reactor.

GROWTH MECHANISM OF TiC WHISKERS PREMRED BY A MODIFIED CHEMICAL VAPOR DEPOSITION METHOD

High quality TiC whiskers have been prepared by a modified chemical vapor deposition (CVD) method using TiCl4 and CH4 as reactant gases and Ni as substrate. The deposition temperature and gas flow mies have ampreciable effect on the whisker growth.The whisker orientations and morphology are determined by X-my diffraction (XRD),scanning electron micmpmph (SEM) and transmission electron microgmph (TEM).In addition to the spherical tips, spiral growth microsteps and obvious terraces are observed at the tips and side faces of whiskers in the present eoperiment. The whiskers grow mostly along (100) direction. The whisker growth mechanism is discussed in detail.

Numerical modeling of SiC by low-pressure chemical vapor deposition from methyltrichlorosilane

The development of functional relationships between the observed deposition rate and the experimental conditions is an important step toward understanding and optimizing low-pressure chemical vapor deposition(LPCVD)or low-pressure chemical vapor infiltration(LPCVI).In the field of ceramic matrix composites(CMCs),methyltrichlorosilane(CH3 SiCl3,MTS)is the most widely used source gas system for SiC,because stoichiometric SiC deposit can be facilitated at 900°C–1300°C.However,the reliability and accuracy of existing numerical models for these processing conditions are rarely reported.In this study,a comprehensive transport model was coupled with gas-phase and surface kinetics.The resulting gas-phase kinetics was confirmed via the measured concentration of gaseous species.The relationship between deposition rate and 24 gaseous species has been effectively evaluated by combining the special superiority of the novel extreme machine learning method and the conventional sticking coefficient method.Surface kinetics were then proposed and shown to reproduce the experimental results.The proposed simulation strategy can be used for different material systems.

Science Letters:Development of supported boron-doping TiO_2 catalysts by chemical vapor deposition

In this study, supported nonmetal (boron) doping TiO2 coating photocatalysts were prepared by chemical vapor deposition (CVD) to enhance the activity under visible light irradiation and avoid the recovering of TiO2. Boron atoms were successfully doped into the lattice of TiO2 through CVD, as evidenced from XPS analysis. B-doped TiO2 coating catalysts showed drastic and strong absorption in the visible light range with a red shift in the band gap transition. This novel B-TiO2 coating photocatalyst showed higher photocatalytic activity in methyl orange degradation under visible light irradiation than that of the pure TiO2 photocatalyst.

Morphological evolution of CdS films prepared by chemical bath deposition

In this article, the growth process of chemical bath deposited CdS films was systematically investigated. The structural, optical, and morphological properties were investigated by X-ray diffraction （XRD）, transmission electron microscope （TEM）, UV-Vis spectrophotometer, scanning electron microscope （SEM）, respectively. CdS nanocubes with size of less than 500 nm and nanocrystal-lites with diameter of less than 5 nm forming in reaction solution are observed. According to the TEM results and the SEM morphological evolution of CdS films, a crystal-lite-by-crystallite growth mechanism is proposed to eluci-date the growth process of chemical bath deposited CdS films based on the present growth mechanism.

Texture Evolutions in Fe-6.5%Si Produced by Rapid Solidification and Chemical Vapor Deposition

Fe-Si ribbons and thin sheets with 6.5%Si content were prepared by means of the single roller rapid solidification and chemical vapor deposition (CVD), respectively. The initial textures of rapidly solidified Fe-6.5%Si ribbons were characteristic of the {100} fiber-type, which became weakened during primary recrystallization in various atmospheres. At the stage of secondary recrystallization, the {100} texture formed in Ar and the {110} texture in hydrogen, while there occurred a texture transformation from the {100} type to the {110} type in vacuum with the increase of annealing temperature. For Fe-6.5%Si sheets prepared by Si deposition in cold-rolled Fe-3%Si matrix sheets, their textures were dominated by the η-fiber (<001>//RD) with the maximum density at the {120}<001> orientations. After homogenization annealing, the η-fiber could evolve into the {130}<001> type or become more concentrated on the {120}<001> orientations, depending on the cold rolling modes of Fe-3%Si matrix sheets.

Continuous-wave operation of InAs/InP quantum dot tunable external-cavity laser grown by metal-organic chemical vapor deposition

We demonstrate high-performance broadband tunable external-cavity lasers(ECLs) with the metal-organic chemical vapor deposition(MOCVD) grown In As/In P quantum dots(QDs) structures. Without cavity facet coatings, the 3-d B spectral bandwidth of the Fabry–Perot(FP) laser is approximately 10.8 nm, while the tuning bandwidth of ECLs is 45 nm.Combined with the anti-reflection(AR)/high-reflection(HR) facet coating, a 92 nm bandwidth tuning range has been obtained with the wavelength covering from 1414 nm to 1506 nm. In most of the tuning range, the threshold current density is lower than 1.5 k A/cm2. The maximum output power of 6.5 m W was achieved under a 500 m A injection current.All achievements mentioned above were obtained under continuous-wave(CW) mode at room temperature(RT).

Mg-doped ZnO radial spherical structures via chemical vapor deposition

Mg-doped ZnO radial spherical structures with nanorods grown on both sides of the spherical shell were successfully prepared via chemical vapor deposition （CVD） of Zn and Mg powders in the absence of a catalyst. The structures associated with different growth temperatures （700, 800, and 850°C） were monitored by scanning electron microscopy （SEM）, and the result shows that the length of the nanorods increase progressively with the growth temperature increasing. X-ray diffraction （XRD） shows that the as-obtained samples can be indexed to high crystallinity with wurtzite structure. The growth of the nanostructures mainly depends on the formation of sphere-like Mg-doped Zn droplets before adding oxygen. Photoluminescence （PL） spectra that show a 39 meV blue shift indicates that the band gap becomes large, because Mg substitutes Zn in the lattice.

Carbon nanotubes for supercapacitors:Consideration of cost and chemical vapor deposition techniques

In this topic, we first discussed the requirement and performance of supercapacitors using carbon nanotubes （CNTs） as the electrode, including specific surface area, purity and cost. Then we reviewed the preparation technique of single wailed CNTs （SWNTs） in relatively large scale by chemical vapor deposition method. Its catalysis on the decomposition of methane and other carbon source, the reactor type and the process control strategies were discussed. Special focus was concentrated on how to increase the yield, selectivity, and purity of SWNTs and how to inhibit the formation of impurities, including amorphous carbon, multiwalled CNTs and the carbon encapsulated metal particles, since these impurities seriously influenced the performance of SWNTs in supercapacitors. Wish it be helpful to further decrease its product cost and for the commercial use in supercapacitors.

Microwave Plasma Chemical Vapor Deposition of Diamond Films on Silicon From Ethanol and Hydrogen

Diamond films with very smooth surface and good optical quality have been deposited onto silicon substrate using microwave plasma chemical vapor deposition (MPCVD) from a gas mixture of ethanol and hydrogen at a low substrate temperature of 450 ℃. The effects of the substrate temperature on the diamond nucleation and the morphology of the diamond film have been investigated and observed with scanning electron microscopy (SEM). The microstructure and the phase of the film have been characterized using Raman spectroscopy and X-ray diffraction (XRD). The diamond nucleation density significantly decreases with the increasing of the substrate temperature. There are only sparse nuclei when the substrate temperature is higher than 800 ℃ although the ethanol concentration in hydrogen is very high. That the characteristic diamond peak in the Raman spectrum of a diamond film prepared at a low substrate temperature of 450 ℃ extends into broadband indicates that the film is of nanophase. No graphite peak appeared in the XRD pattern confirms that the film is mainly composed of SP3 carbon. The diamond peak in the XRD pattern also broadens due to the nanocrystalline of the film.

High-Frequency AlGaN/GaN High-Electron-Mobility Transistors with Regrown Ohmic Contacts by Metal-Organic Chemical Vapor Deposition

Nonalloyed ohmic contacts regrown by metal-organic chemical vapor deposition are performed on AlGaN/GaN high-electron-mobility transistors. Low ohmic contact resistance of 0.15Ω.mm is obtained. It is found that the sidewall obliquity near the regrown interface induced by the plasma dry etching has great influence on the total contact resistance. The fabricated device with a 100-nm T-shaped gate demonstrates a maximum drain current density of 0.95 A/mm at Vgs = 1 V and a maximum peak extrinsic transcondutance Gm of 216mS/ram. Moreover, a current gain cut-off frequency fT of 115 GHz and a maximum oscillation frequency fmax of 127 GHz are achieved.

Preparation and characteristics of C/C composite brake disc by multi-cylindrical chemical vapor deposition processes

The C/C composite brake discs were prepared by tri-cylindrical chemical vapor deposition （CVD） process. The optimum processing parameters were as follows： deposition temperature was 830 - 930 ℃, the gas- flow rates of N2 and propylene were 4.8 - 5.2 m^3/h and 5.8 - 6.2 m^3/h, respectively, the furnace pressure was 4.5 - 5.5 kPa and the deposition time was 200 h. The effects of processing parameters on the densified rates, thermal-physical property and mechanical performance of C/C composite brake discs were studied. The results show that density, heat conductivity, bend strength and abrasion ratio of the multi-cylindrica brake discs are 1. 02 - 1. 78 g/cm^3 , 31 W/（m·K）, 114 MPa and 7μm/s, respectively, which are approximately similar to those of the singlecylindrical ones. The gas tlow rate has no relation to the number of the cylinder and furnace loading. The utilization ratio of carbon can be improved by multi-cylinder CVD process without changing the characteristics of brake disc.

Fabrication of 160-nm T-gate metamorphic AlInAs/GaInAs HEMTs on GaAs substrates by metal organic chemical vapour deposition

The fabrication and performance of 160-nm gate-length metamorphic AlInAs/GaInAs high electron mobility transistors （mHEMTs） grown on GaAs substrate by metal organic chemical vapour deposition （MOCVD） are reported. By using a novel combined optical and e-beam photolithography technology, submicron mHEMTs devices have been achieved. The devices exhibit good DC and RF performance. The maximum current density was 817 mA/mm and the maximum transconductance was 828 mS/mm. The non-alloyed Ohmic contact resistance Rc was as low as 0.02 Ω- ram. The unity current gain cut-off frequency （fT） and the maximum oscillation frequency （fmax） were 146 GHz and 189 GHz, respectively. This device has the highest fT yet reported for a 160-nm gate-length HEMTs grown by MOCVD. The output conductance is 28.9 mS/mm, which results in a large voltage gain of 28.6, Also, an input capacitance to gate-drain feedback capacitance ratio, Cgs/Cgd, of 4.3 is obtained in the device.