The pressure drop during production in the near-wellbore zone of gas condensate reservoirs causes condensate formation in this area.Condensate blockage in this area causes an additional pressure drop that weakens the ...The pressure drop during production in the near-wellbore zone of gas condensate reservoirs causes condensate formation in this area.Condensate blockage in this area causes an additional pressure drop that weakens the effective parameters of production,such as permeability.Reservoir rock wettability alteration to gas-wet through chemical treatment is one of the solutions to produce these condensates and eliminate condensate blockage in the area.In this study,an anionic fluorinated surfactant was synthesized and used for chemical treatment and carbonate rock wettability alteration.The synthesized surfactant was characterized by Fourier transform infrared spectroscopy and thermogravimetric analysis.Then,using surface tension tests,its critical micelle concentration(CMC)was determined.Contact angle experiments on chemically treated sections with surfactant solutions and spontaneous imbibition were performed to investigate the wettability alteration.Surfactant adsorption on porous media was calculated using flooding.Finally,the surfactant foamability was investigated using a Ross-Miles foam generator.According to the results,the synthesized surfactant has suitable thermal stability for use in gas condensate reservoirs.A CMC of 3500 ppm was obtained for the surfactant based on the surface tension experiments.Contact angle experiments show the ability of the surfactant to chemical treatment and wettability alteration of carbonate rocks to gas-wet so that at the constant concentration of CMC and at 373 K,the contact angles at treatment times of 30,60,120 and 240 min were obtained 87.94°,93.50°,99.79°and 106.03°,respectively.However,this ability varies at different surfactant concentrations and temperatures.The foamability test also shows the suitable stability of the foam generated by the surfactant,and a foam half-life time of 13 min was obtained for the surfactant at CMC.展开更多
Effect of Ti(iso-C3H7O)4 treatment on the photoinduced charge carrier kinetics of nanocrystalline porous TiO2 films is studied by time-resolved microwave conductivity measurements. Analysis of the transient photocond...Effect of Ti(iso-C3H7O)4 treatment on the photoinduced charge carrier kinetics of nanocrystalline porous TiO2 films is studied by time-resolved microwave conductivity measurements. Analysis of the transient photoconductivity decays indicates that Ti(iso-C3H7O)4 treatment leads to an increased concentration of photogenerated charge carriers and a fast interfacial transfer rate of holes via the surface modification of the freshly growing TiO2 nanocrystallites.展开更多
AFM has been utilized to study the surface topography and the local conductivity of nanocrystalline TiO2 films. Improving the local conductivity by Ti(iso-C3H7O)4 treatment is characterized by quantitative analysis o...AFM has been utilized to study the surface topography and the local conductivity of nanocrystalline TiO2 films. Improving the local conductivity by Ti(iso-C3H7O)4 treatment is characterized by quantitative analysis of the simultaneous current image. The mechanism of Ti(iso C3H7O)4 treatment is discussed.展开更多
Multi-walled carbon nanombes with homogeneous diameters (40 - 60 nm), produced by chemical vapor deposition of hydrocarbon gas, are purified by nitric acids. Infrared and Raman studies indicate that oxygen containin...Multi-walled carbon nanombes with homogeneous diameters (40 - 60 nm), produced by chemical vapor deposition of hydrocarbon gas, are purified by nitric acids. Infrared and Raman studies indicate that oxygen containing surface groups, which are predominately carboxylic, phenolic and lactonic groups, are introduced into purified carbon nanotubes. Then three kinds of block-form porous tablets of carbon nanotubes are fabricated as electrodes in electrochemical double-layer capacitors. Using mounded mixture comprising carbon nanotubes and binder powders provides these tablets. Comparison of the effect of different processing on the structural performance of the capacitors is specifically investigated. Using chemically treated electrodes, electrochemical double-layer capacitors with a specific capacitance of about 33 F/g are obtained with 38 wt % H2SO4 as the electrolyte.展开更多
Polypropylene (PP) matrix composites reinforced with chemically treated Almond Shell (AS) particles with and without compatibilizer (PP-g-MA) was prepared by a twin-screw extrusion at loading of 20 wt.% AS parti...Polypropylene (PP) matrix composites reinforced with chemically treated Almond Shell (AS) particles with and without compatibilizer (PP-g-MA) was prepared by a twin-screw extrusion at loading of 20 wt.% AS particles. Two types of chemical treatments (alkali treatment with sodium hydroxide and etherification with dodecane bromide) of the particles were carried out to improve the interface adhesion between particles and PP matrix. Results show that chemical modifications of AS particles affect the mechanical and viscoelastic properties of AS/PP composites. The composites reinforced with alkali treated particles and the compatibilized matrix lead to a notable increase in the Young's modulus (14%) compared to the composites with untreated AS particles. The ductility of composite was also evaluated by the yield strain, and results show a notable increase (31%) compared to that of composites with untreated particles. The thermal stability increased with the use of etherification (385 ℃), with gains in the temperature up to 23 ℃ compared to neat PP (362 ℃). The achieved results show that the AS/PP composites can be used in several applications. A thermoplastic matrix compsite mixed with treated AS particles appears to be a good alternative to obtain environmentally friendly products.展开更多
Background Silicon gel is unfavourable for cell attachment and growth. This study was to study if pretreating the surface of silicon gel with chemical agents affects the proliferation of epithelial cells Methods Si...Background Silicon gel is unfavourable for cell attachment and growth. This study was to study if pretreating the surface of silicon gel with chemical agents affects the proliferation of epithelial cells Methods Silicon gel was made and treated with either mixed acid solution (containing 232 g/dm 3 of H 2SO 4 and 8 g/dm 3 of K 2Cr 2O 7) or 300 cm 3/dm 3 peroxide for 5, 10, and 15 minutes or 10, 15, and 20 minutes, respectively The cultured corneal epithelial cells were seeded onto those silicon gels and kept for 13 days Immunohistochemical investigations were then carried out for integrin (alpha 6 or beta 4) and actin KH*2/5DResults Growth of the epithelial cells in silicon gels treated with mixed acid solution for 10 minutes and 15 minutes was much significant than that in the untreated gels After a 12-hour culture, a small number of corneal epithelial cells were proliferated on the surface of the silicon gels that had been treated with peroxide for 15 minutes After a 3-day culture, those cells were further proliferated and fused together The corneal epithelial cells did not grow well in the silicon gels treated with peroxide for 10 or 20 minutes Immunostaining revealed the expression of actin and integrin alpha 6 or beta 4 on the silicon gels that were treated with mixed acid solution for 10 minutes or peroxide for 15 minutes Conclusion Silicon gels treated either with mixed acid solution for 10 or 15 minutes or with peroxide for 15 minutes improves cell proliferation展开更多
With the progress of ULSI technology, materials with low dielectric constant are required to replace SiO2 film as the interlayer to scale down the interconnection delay. Fluorinated Si oxide thin films (SiOF) are a pr...With the progress of ULSI technology, materials with low dielectric constant are required to replace SiO2 film as the interlayer to scale down the interconnection delay. Fluorinated Si oxide thin films (SiOF) are a promising material for the low dielectric constant and the process compatibility in existing technology. However, SiOF films are liable to absorb moisture when exposed to air. By treating the SiOF films with O-2 plasma, it was found that the moisture resistibility of SiOF films was remarkably improved. The mechanism of the improvement in stability of dielectric constant was investigated. The results show that: 1) F atoms dissociated from the films and the bond angle of Si-O-Si decreased. 2) The plasma treatment enhanced the strength of Si-F bonds by removing unstable =SiF2 structures in the films. Resistibility of SiOF films in moisture was improved.展开更多
This paper is aimed to show the influence of initial chemical pretreatment prior to subsequent plasma activation of aluminum surfaces.The results of our study showed that the state of the topmost surface layer(i.e.th...This paper is aimed to show the influence of initial chemical pretreatment prior to subsequent plasma activation of aluminum surfaces.The results of our study showed that the state of the topmost surface layer(i.e.the surface morphology and chemical groups)of plasma modified aluminum significantly depends on the chemical precleaning.Commonly used chemicals(isopropanol,trichlorethane,solution of Na OH in deionized water)were used as precleaning agents.The plasma treatments were done using a radio frequency driven atmospheric pressure plasma pencil developed at Masaryk University,which operates in Ar,Ar/O_2 gas mixtures.The effectiveness of the plasma treatment was estimated by the wettability measurements,showing high wettability improvement already after 0.3 s treatment.The effects of surface cleaning(hydrocarbon removal),surface oxidation and activation(generation of OH groups)were estimated using infrared spectroscopy.The changes in the surface morphology were measured using scanning electron microscopy.Optical emission spectroscopy measurements in the near-to-surface region with temperature calculations showed that plasma itself depends on the sample precleaning procedure.展开更多
Experiments were carried out to study the removal of heavy metals from municipal sewage sludge by proper method for land application. The sequential extractions for metal fractionation showed that the non digested slu...Experiments were carried out to study the removal of heavy metals from municipal sewage sludge by proper method for land application. The sequential extractions for metal fractionation showed that the non digested sludge from Guangzhou contained Cu and Zn principally bound to carbonate and oxides and the metal sulfides were low. Among H 2SO 4, EDTA and NH 4HCO 3 extractant agents, H 2SO 4 was the most efficient and economic in removing the heavy metals, especially with the addition of the concentrated acid. Plant experiment in pots with Chinese cabbage ( Brassica Chinensis ) showed that the acidified sludges neutralized with alkaline amendments such as phosphate rock could increase significantly the plant yield and decreased the soil and plant contamination by heavy metals originated from sewage sludge.展开更多
In order to clarify the effect of drying on structural changes of DMSO swell treated and DEA-SO2-DMSO decrystallization treated Chinese fir (Cunninghamia lanceolate) wood, the stress relaxation of treated oven-dry s...In order to clarify the effect of drying on structural changes of DMSO swell treated and DEA-SO2-DMSO decrystallization treated Chinese fir (Cunninghamia lanceolate) wood, the stress relaxation of treated oven-dry specimens during the processes of temperature elevation and reduction and that of treated wet specimens at constant temperature were determined. A stress decrease process and a stress increase process were observed in all stress ratio curves of wood during the processes of decreasing temperature. Untreated wood, during the process of temperature reduction under higher initial temperature conditions and during the process of temperature elevation, has a larger stress decrease than treated woods. In a wet state this trend is reversed. It indicated that the drying set made treated woods have a smaller increase in fluidity of wood constituents with increasing temperature. Some bonding between decrystallization reagents and wood molecules may occur.展开更多
The objective of this work is to carry out the chemical treatment for the hemp fabrics in a closed vacuum system and to prepare bio-based composites using treated hemp fabrics.The change in surface tension of the trea...The objective of this work is to carry out the chemical treatment for the hemp fabrics in a closed vacuum system and to prepare bio-based composites using treated hemp fabrics.The change in surface tension of the treated fabrics was measured using contact angle measurement and the wetting behavior using a tensiometer.Bio-based composites were fabricated using bio-based epoxy resin and different chemically treated fabrics.The flexural strength and dynamic water absorption behavior of the composites were characterized.The acetylated fabrics showed very good wetting behavior,and the contact angle values were marginally low compared to other treatment techniques.The bio-based composites fabricated using maleic anhydride treated fabrics achieved the flexural strength of 148 MPa and the dynamic water absorption values were less than 6%.The acetylated and maleic anhydride treatment methods were effective chemical treatments for the hemp fabrics and they enhanced both the wettability and fiber-matrix interaction.The chemical treatment methods that are carried out in the sealed environment can be utilized for all other natural fabrics that help overcome the moisture absorption behavior.展开更多
The particle characterization from the influent and effluent of a chemical-biological flocculation (CBF) process was studied with a laser diffraction device. Water samples from a chemically enhanced primary treatme...The particle characterization from the influent and effluent of a chemical-biological flocculation (CBF) process was studied with a laser diffraction device. Water samples from a chemically enhanced primary treatment (CEPT) process and a primary sediment tank process were also analyzed for comparison. The results showed that CBF process was not only effective for both the big size particles and small size particles removal, but also the best particle removal process in the three processes. The results also indicated that CBF process was superior to CEPT process in the heavy metals removal. The high and non-selective removal for heavy metals might be closely related to its strong ability to eliminate small particles. Samples from different locations in CBF reactors showed that small particles were easier to aggregate into big ones and those disrupted flocs could properly flocculate again along CBF reactor because of the biological flocculation.展开更多
The influences of chromium-free chemical conversion treatment and anodizing treatment on bonding strength of AZ31 magnesium alloy were studied by lap-shear test, SEM and electrochemical methods. Both chemical conversi...The influences of chromium-free chemical conversion treatment and anodizing treatment on bonding strength of AZ31 magnesium alloy were studied by lap-shear test, SEM and electrochemical methods. Both chemical conversion treatment and anodizing can increase the bonding strength. The anodizing treatment gives higher bonding strength and better corrosion resistance than chemical conversion treatment. The increase of bonding strength by the treatmetlts may be attributed to the uneven surface structures with micro-pores, resulting in increased bonding areas and the embedding effect.展开更多
This paper studies a compound treatment. i. e. liquid S , N,C co-diffusing with rare earth (RE) and then oxidization , for hot-working die steels , and the effect of RE on thermal fatigue behavior of the diffused laye...This paper studies a compound treatment. i. e. liquid S , N,C co-diffusing with rare earth (RE) and then oxidization , for hot-working die steels , and the effect of RE on thermal fatigue behavior of the diffused layer. XRD and SEM energy spectrum prove that trace RE element actually penetrates into the surface layer of steels. The result shows that RE can reduce the gradient of change of hardness in diffused layer, improve the morphology and distribution of compounds , and reduce the degree of surface alligator crack for thermal fatigue. The behavior of thermal fatigue of hot-working die steels is raised by 70% or so after the application of RE. The effect of RE is analysed according to the theory.展开更多
Sodium beta alumina(Na-β-alumina) films were synthesized by heat treatment of NaAl6O(9.5)and γ-NaA1O2 films at temperatures of 1 373-1 573 K.Single-phase γ-NaA1O2 and NaAl6O(9.5) films were prepared by laser ...Sodium beta alumina(Na-β-alumina) films were synthesized by heat treatment of NaAl6O(9.5)and γ-NaA1O2 films at temperatures of 1 373-1 573 K.Single-phase γ-NaA1O2 and NaAl6O(9.5) films were prepared by laser chemical vapor deposition at the deposition temperatures of 976 and 1 100 K,respectively.Subsequent heat treatment of the films resulted in the formation of Na-β-alumina with α-Al2O3 at temperatures above 1 373 K for NaAl6O(9.5) and 1 473 K for γ-NaA1O2.On heat treatment at temperatures of 1 473-1 573 K,the faceted morphology with terraces of the as-deposited(110)-oriented γ-NaAlO2 films transformed to a porous morphology with platelet grains comprising Na-β-alumina and α-Al2O3.On heat treatment at temperatures of1 373-1 473 K,the pyramidal,faceted grains of as-deposited NaAl6O(9.5) films transformed to planer,shapeanisotropic morphology in the film of mixed Na-β-alumina and α-Al2O3.A dense morphology was observed in both the as-deposited and heat-treated NaAl6O(9.5) films.展开更多
TiO_2 films were coated on the surface of diamond particles using a sol-gel method. The effects of heat treatment temperature on the morphology, phase composition and chemical bond of diamond particles coated with TiO...TiO_2 films were coated on the surface of diamond particles using a sol-gel method. The effects of heat treatment temperature on the morphology, phase composition and chemical bond of diamond particles coated with TiO2 films were investigated through SEM, TEM, X-ray diffraction analysis, Raman spectroscopy, FTIR, and XPS. The results showed that when being heat-treated at 600 ℃, the amorphous TiO_2 film transfered to the anatase film which bonded well with diamond substrate. Meanwhile, the Ti-O-C bond formed between TiO2 film and diamond substrate. When being heat-treated at 800 ℃, TiO2 film was still anatase, and partial diamond began to graphitize. The graphitizated carbon could also form the Ti-O-C bond with TiO_2 film, although TiO_2 film would tend to crack in this case.展开更多
The impregnation of a special grade PAN precursor,fibers wus carried out in a 8 wt% KMnO4 aqueous solution to obtain modified PAN precursor fibers. The effects of modification on the chemical stncture and the mechani...The impregnation of a special grade PAN precursor,fibers wus carried out in a 8 wt% KMnO4 aqueous solution to obtain modified PAN precursor fibers. The effects of modification on the chemical stncture and the mechanical properties of precursor fibers thermally stabilized and their resulting carbon fibers u'ere characterized by the combiination use of densities, wide-angle X-ray diffraction (WAXD), X-ray photoelectron speetroscopy (XPS), elemental analysis ( EA ), Fourier traasform infrared spectroscopy (FT-IR) and scanning electron microscope (SEM), etc.KMnO4 as a strong oxidizer can swell, oxidize and corrode the skin of a precursor.fiber, and transform C≡N groups to C≡N ones, meamchile , it can decreuse the crystal .size increuse the orientation index and the costallinity index, furthermore it can increuse the densities of modified PAN precursors and resuhing thermally stabilized fibers. As a result, the carbon fibers developed from modified PAN fibers show an improvement in tensile strength of 31.25 % and an improvement in elongation of 77.78 % , but a decrease of 16. 52% in Young's modulus.展开更多
Carbon nanotube (CNT)/maleic acid anhydride (MAH)-grafted polypropylene (PP) composites were prepared by in situ grafting method. Infrared spectroscopy showed that the CNTs were linked to PP by MAH grafting. The...Carbon nanotube (CNT)/maleic acid anhydride (MAH)-grafted polypropylene (PP) composites were prepared by in situ grafting method. Infrared spectroscopy showed that the CNTs were linked to PP by MAH grafting. The microstructures and calorimetry analysis indicated that the crystallization behaviors of the filled and unfilled PP were quite different. The addition of CNTs dramatically reduced the spherulite size, increased crystallization rate and improved the thermal stability of PP. These results confirmed the expected nucleant effect of CNT on the crystallization of PP. Scanning and transmission electron microscopy showed that the CNTs were dispersed homogeneously, indicating that the original CNT bundles were separated into individual tubes by the grafting.展开更多
文摘The pressure drop during production in the near-wellbore zone of gas condensate reservoirs causes condensate formation in this area.Condensate blockage in this area causes an additional pressure drop that weakens the effective parameters of production,such as permeability.Reservoir rock wettability alteration to gas-wet through chemical treatment is one of the solutions to produce these condensates and eliminate condensate blockage in the area.In this study,an anionic fluorinated surfactant was synthesized and used for chemical treatment and carbonate rock wettability alteration.The synthesized surfactant was characterized by Fourier transform infrared spectroscopy and thermogravimetric analysis.Then,using surface tension tests,its critical micelle concentration(CMC)was determined.Contact angle experiments on chemically treated sections with surfactant solutions and spontaneous imbibition were performed to investigate the wettability alteration.Surfactant adsorption on porous media was calculated using flooding.Finally,the surfactant foamability was investigated using a Ross-Miles foam generator.According to the results,the synthesized surfactant has suitable thermal stability for use in gas condensate reservoirs.A CMC of 3500 ppm was obtained for the surfactant based on the surface tension experiments.Contact angle experiments show the ability of the surfactant to chemical treatment and wettability alteration of carbonate rocks to gas-wet so that at the constant concentration of CMC and at 373 K,the contact angles at treatment times of 30,60,120 and 240 min were obtained 87.94°,93.50°,99.79°and 106.03°,respectively.However,this ability varies at different surfactant concentrations and temperatures.The foamability test also shows the suitable stability of the foam generated by the surfactant,and a foam half-life time of 13 min was obtained for the surfactant at CMC.
基金Supported by the National Natural Science Foundation of China (Grant No.30070606) and Graduate Cultivation Foundation of Beijing Forestry University (Grant No.304)
基金This work was supported by National Research Fund for Fundamental Key Project(G2000028205)Innovative Foundation of Chinese Academy of Sciences(KGCX2-303-02)the Project of the National Natural Science Foundation of China(29873057).
文摘Effect of Ti(iso-C3H7O)4 treatment on the photoinduced charge carrier kinetics of nanocrystalline porous TiO2 films is studied by time-resolved microwave conductivity measurements. Analysis of the transient photoconductivity decays indicates that Ti(iso-C3H7O)4 treatment leads to an increased concentration of photogenerated charge carriers and a fast interfacial transfer rate of holes via the surface modification of the freshly growing TiO2 nanocrystallites.
基金This work was supported by National Research Fund for Fundamental Key Project (G2000028205) Innovative Foundation of Chinese Academy of Sciences and the Project of the National Natural Science Foundation of China (29873057). We thank Dr. D.S. Zhang for
文摘AFM has been utilized to study the surface topography and the local conductivity of nanocrystalline TiO2 films. Improving the local conductivity by Ti(iso-C3H7O)4 treatment is characterized by quantitative analysis of the simultaneous current image. The mechanism of Ti(iso C3H7O)4 treatment is discussed.
基金Project supported by National High-Technology Research and De-velopment Program(Grant No .863 -2002AA302302)
文摘Multi-walled carbon nanombes with homogeneous diameters (40 - 60 nm), produced by chemical vapor deposition of hydrocarbon gas, are purified by nitric acids. Infrared and Raman studies indicate that oxygen containing surface groups, which are predominately carboxylic, phenolic and lactonic groups, are introduced into purified carbon nanotubes. Then three kinds of block-form porous tablets of carbon nanotubes are fabricated as electrodes in electrochemical double-layer capacitors. Using mounded mixture comprising carbon nanotubes and binder powders provides these tablets. Comparison of the effect of different processing on the structural performance of the capacitors is specifically investigated. Using chemically treated electrodes, electrochemical double-layer capacitors with a specific capacitance of about 33 F/g are obtained with 38 wt % H2SO4 as the electrolyte.
文摘Polypropylene (PP) matrix composites reinforced with chemically treated Almond Shell (AS) particles with and without compatibilizer (PP-g-MA) was prepared by a twin-screw extrusion at loading of 20 wt.% AS particles. Two types of chemical treatments (alkali treatment with sodium hydroxide and etherification with dodecane bromide) of the particles were carried out to improve the interface adhesion between particles and PP matrix. Results show that chemical modifications of AS particles affect the mechanical and viscoelastic properties of AS/PP composites. The composites reinforced with alkali treated particles and the compatibilized matrix lead to a notable increase in the Young's modulus (14%) compared to the composites with untreated AS particles. The ductility of composite was also evaluated by the yield strain, and results show a notable increase (31%) compared to that of composites with untreated particles. The thermal stability increased with the use of etherification (385 ℃), with gains in the temperature up to 23 ℃ compared to neat PP (362 ℃). The achieved results show that the AS/PP composites can be used in several applications. A thermoplastic matrix compsite mixed with treated AS particles appears to be a good alternative to obtain environmentally friendly products.
文摘Background Silicon gel is unfavourable for cell attachment and growth. This study was to study if pretreating the surface of silicon gel with chemical agents affects the proliferation of epithelial cells Methods Silicon gel was made and treated with either mixed acid solution (containing 232 g/dm 3 of H 2SO 4 and 8 g/dm 3 of K 2Cr 2O 7) or 300 cm 3/dm 3 peroxide for 5, 10, and 15 minutes or 10, 15, and 20 minutes, respectively The cultured corneal epithelial cells were seeded onto those silicon gels and kept for 13 days Immunohistochemical investigations were then carried out for integrin (alpha 6 or beta 4) and actin KH*2/5DResults Growth of the epithelial cells in silicon gels treated with mixed acid solution for 10 minutes and 15 minutes was much significant than that in the untreated gels After a 12-hour culture, a small number of corneal epithelial cells were proliferated on the surface of the silicon gels that had been treated with peroxide for 15 minutes After a 3-day culture, those cells were further proliferated and fused together The corneal epithelial cells did not grow well in the silicon gels treated with peroxide for 10 or 20 minutes Immunostaining revealed the expression of actin and integrin alpha 6 or beta 4 on the silicon gels that were treated with mixed acid solution for 10 minutes or peroxide for 15 minutes Conclusion Silicon gels treated either with mixed acid solution for 10 or 15 minutes or with peroxide for 15 minutes improves cell proliferation
基金The work was supported by the National Natural Science Foundation of China(No.69776026)the Foundation for University Key Teacher by the Ministry of Education.
文摘With the progress of ULSI technology, materials with low dielectric constant are required to replace SiO2 film as the interlayer to scale down the interconnection delay. Fluorinated Si oxide thin films (SiOF) are a promising material for the low dielectric constant and the process compatibility in existing technology. However, SiOF films are liable to absorb moisture when exposed to air. By treating the SiOF films with O-2 plasma, it was found that the moisture resistibility of SiOF films was remarkably improved. The mechanism of the improvement in stability of dielectric constant was investigated. The results show that: 1) F atoms dissociated from the films and the bond angle of Si-O-Si decreased. 2) The plasma treatment enhanced the strength of Si-F bonds by removing unstable =SiF2 structures in the films. Resistibility of SiOF films in moisture was improved.
基金the Czech Science Foundation(Project No.104/08/02290)the Czech Ministry of Industry and Trade(Project CZ.1.03/5.1.00/12.00010)the Czech Ministry of Education(Project MSM0021622411)
文摘This paper is aimed to show the influence of initial chemical pretreatment prior to subsequent plasma activation of aluminum surfaces.The results of our study showed that the state of the topmost surface layer(i.e.the surface morphology and chemical groups)of plasma modified aluminum significantly depends on the chemical precleaning.Commonly used chemicals(isopropanol,trichlorethane,solution of Na OH in deionized water)were used as precleaning agents.The plasma treatments were done using a radio frequency driven atmospheric pressure plasma pencil developed at Masaryk University,which operates in Ar,Ar/O_2 gas mixtures.The effectiveness of the plasma treatment was estimated by the wettability measurements,showing high wettability improvement already after 0.3 s treatment.The effects of surface cleaning(hydrocarbon removal),surface oxidation and activation(generation of OH groups)were estimated using infrared spectroscopy.The changes in the surface morphology were measured using scanning electron microscopy.Optical emission spectroscopy measurements in the near-to-surface region with temperature calculations showed that plasma itself depends on the sample precleaning procedure.
文摘Experiments were carried out to study the removal of heavy metals from municipal sewage sludge by proper method for land application. The sequential extractions for metal fractionation showed that the non digested sludge from Guangzhou contained Cu and Zn principally bound to carbonate and oxides and the metal sulfides were low. Among H 2SO 4, EDTA and NH 4HCO 3 extractant agents, H 2SO 4 was the most efficient and economic in removing the heavy metals, especially with the addition of the concentrated acid. Plant experiment in pots with Chinese cabbage ( Brassica Chinensis ) showed that the acidified sludges neutralized with alkaline amendments such as phosphate rock could increase significantly the plant yield and decreased the soil and plant contamination by heavy metals originated from sewage sludge.
基金the National Natural Science Foundation of China (Grant No.30070606) and Graduate Cultivation Foundation of Beijing Forestry University(Grant No.304)
基金Supported by the National Natural Science Foundation of China (Grant No. 30070606)Graduate Cultivation Foundation of Beijing Forestry University(Grant No. 304)
文摘In order to clarify the effect of drying on structural changes of DMSO swell treated and DEA-SO2-DMSO decrystallization treated Chinese fir (Cunninghamia lanceolate) wood, the stress relaxation of treated oven-dry specimens during the processes of temperature elevation and reduction and that of treated wet specimens at constant temperature were determined. A stress decrease process and a stress increase process were observed in all stress ratio curves of wood during the processes of decreasing temperature. Untreated wood, during the process of temperature reduction under higher initial temperature conditions and during the process of temperature elevation, has a larger stress decrease than treated woods. In a wet state this trend is reversed. It indicated that the drying set made treated woods have a smaller increase in fluidity of wood constituents with increasing temperature. Some bonding between decrystallization reagents and wood molecules may occur.
基金This research was supported by the Austrian Research Promotion Agency(FFG).
文摘The objective of this work is to carry out the chemical treatment for the hemp fabrics in a closed vacuum system and to prepare bio-based composites using treated hemp fabrics.The change in surface tension of the treated fabrics was measured using contact angle measurement and the wetting behavior using a tensiometer.Bio-based composites were fabricated using bio-based epoxy resin and different chemically treated fabrics.The flexural strength and dynamic water absorption behavior of the composites were characterized.The acetylated fabrics showed very good wetting behavior,and the contact angle values were marginally low compared to other treatment techniques.The bio-based composites fabricated using maleic anhydride treated fabrics achieved the flexural strength of 148 MPa and the dynamic water absorption values were less than 6%.The acetylated and maleic anhydride treatment methods were effective chemical treatments for the hemp fabrics and they enhanced both the wettability and fiber-matrix interaction.The chemical treatment methods that are carried out in the sealed environment can be utilized for all other natural fabrics that help overcome the moisture absorption behavior.
基金Project supported by the Hi-Tech Research and Development Program (863) of China (No. 2002AA601320) the Shandong Environment Protection Bureau Program (No. 2006032, 2006043)the Ph.D Fund of Shandong Jianzhu University (No. 624006, 2006043).
文摘The particle characterization from the influent and effluent of a chemical-biological flocculation (CBF) process was studied with a laser diffraction device. Water samples from a chemically enhanced primary treatment (CEPT) process and a primary sediment tank process were also analyzed for comparison. The results showed that CBF process was not only effective for both the big size particles and small size particles removal, but also the best particle removal process in the three processes. The results also indicated that CBF process was superior to CEPT process in the heavy metals removal. The high and non-selective removal for heavy metals might be closely related to its strong ability to eliminate small particles. Samples from different locations in CBF reactors showed that small particles were easier to aggregate into big ones and those disrupted flocs could properly flocculate again along CBF reactor because of the biological flocculation.
基金Funded by the Key Project of Science and Technology of Ministry of Education of China(No.108129)
文摘The influences of chromium-free chemical conversion treatment and anodizing treatment on bonding strength of AZ31 magnesium alloy were studied by lap-shear test, SEM and electrochemical methods. Both chemical conversion treatment and anodizing can increase the bonding strength. The anodizing treatment gives higher bonding strength and better corrosion resistance than chemical conversion treatment. The increase of bonding strength by the treatmetlts may be attributed to the uneven surface structures with micro-pores, resulting in increased bonding areas and the embedding effect.
文摘This paper studies a compound treatment. i. e. liquid S , N,C co-diffusing with rare earth (RE) and then oxidization , for hot-working die steels , and the effect of RE on thermal fatigue behavior of the diffused layer. XRD and SEM energy spectrum prove that trace RE element actually penetrates into the surface layer of steels. The result shows that RE can reduce the gradient of change of hardness in diffused layer, improve the morphology and distribution of compounds , and reduce the degree of surface alligator crack for thermal fatigue. The behavior of thermal fatigue of hot-working die steels is raised by 70% or so after the application of RE. The effect of RE is analysed according to the theory.
基金Funded by the Ministry of Education,Culture,Sports,Science and Technology,a Grant-in-Aid for Challenging Exploratory Research(No.26560235)the ARCMG–IMR Cooperative Program(No.14G0402)of Tohoku Universitythe China Scholarship Council and the 111 Project(No.B13035)of China
文摘Sodium beta alumina(Na-β-alumina) films were synthesized by heat treatment of NaAl6O(9.5)and γ-NaA1O2 films at temperatures of 1 373-1 573 K.Single-phase γ-NaA1O2 and NaAl6O(9.5) films were prepared by laser chemical vapor deposition at the deposition temperatures of 976 and 1 100 K,respectively.Subsequent heat treatment of the films resulted in the formation of Na-β-alumina with α-Al2O3 at temperatures above 1 373 K for NaAl6O(9.5) and 1 473 K for γ-NaA1O2.On heat treatment at temperatures of 1 473-1 573 K,the faceted morphology with terraces of the as-deposited(110)-oriented γ-NaAlO2 films transformed to a porous morphology with platelet grains comprising Na-β-alumina and α-Al2O3.On heat treatment at temperatures of1 373-1 473 K,the pyramidal,faceted grains of as-deposited NaAl6O(9.5) films transformed to planer,shapeanisotropic morphology in the film of mixed Na-β-alumina and α-Al2O3.A dense morphology was observed in both the as-deposited and heat-treated NaAl6O(9.5) films.
基金Funded by National Natural Science Foundation of China(No.51375157)Shanghai Aerospace Eighth Research Institute SAST Foundation(No.2015044)+1 种基金the Central University Basic Scientific Research Business Expenses,State Key Laboratory of Silicate Materials for Architectures Program(No.SYSJJ2015-09)the Hunan Province Key Laboratory of Environmental Photocatalysis Application Technology Program(No.CCSU-KF-1504)
文摘TiO_2 films were coated on the surface of diamond particles using a sol-gel method. The effects of heat treatment temperature on the morphology, phase composition and chemical bond of diamond particles coated with TiO2 films were investigated through SEM, TEM, X-ray diffraction analysis, Raman spectroscopy, FTIR, and XPS. The results showed that when being heat-treated at 600 ℃, the amorphous TiO_2 film transfered to the anatase film which bonded well with diamond substrate. Meanwhile, the Ti-O-C bond formed between TiO2 film and diamond substrate. When being heat-treated at 800 ℃, TiO2 film was still anatase, and partial diamond began to graphitize. The graphitizated carbon could also form the Ti-O-C bond with TiO_2 film, although TiO_2 film would tend to crack in this case.
基金Founded by the National Natural Science Foundation of China(No.50333070)
文摘The impregnation of a special grade PAN precursor,fibers wus carried out in a 8 wt% KMnO4 aqueous solution to obtain modified PAN precursor fibers. The effects of modification on the chemical stncture and the mechanical properties of precursor fibers thermally stabilized and their resulting carbon fibers u'ere characterized by the combiination use of densities, wide-angle X-ray diffraction (WAXD), X-ray photoelectron speetroscopy (XPS), elemental analysis ( EA ), Fourier traasform infrared spectroscopy (FT-IR) and scanning electron microscope (SEM), etc.KMnO4 as a strong oxidizer can swell, oxidize and corrode the skin of a precursor.fiber, and transform C≡N groups to C≡N ones, meamchile , it can decreuse the crystal .size increuse the orientation index and the costallinity index, furthermore it can increuse the densities of modified PAN precursors and resuhing thermally stabilized fibers. As a result, the carbon fibers developed from modified PAN fibers show an improvement in tensile strength of 31.25 % and an improvement in elongation of 77.78 % , but a decrease of 16. 52% in Young's modulus.
基金supported by the National Natural Science Foundation of China(Nos.50772033,50372020)the Natural Science Fund in Hunan Province,China(No.2007FJ3003).
文摘Carbon nanotube (CNT)/maleic acid anhydride (MAH)-grafted polypropylene (PP) composites were prepared by in situ grafting method. Infrared spectroscopy showed that the CNTs were linked to PP by MAH grafting. The microstructures and calorimetry analysis indicated that the crystallization behaviors of the filled and unfilled PP were quite different. The addition of CNTs dramatically reduced the spherulite size, increased crystallization rate and improved the thermal stability of PP. These results confirmed the expected nucleant effect of CNT on the crystallization of PP. Scanning and transmission electron microscopy showed that the CNTs were dispersed homogeneously, indicating that the original CNT bundles were separated into individual tubes by the grafting.