Hole cleaning evaluation and installation spacing optimization of cuttings bed remover in extended-reach drilling

In extended-reach or long-horizontal drilling,cuttings usually deposit at the bottom of the annulus.Once cuttings accumulate to a certain thickness,complex problems such as excessive torque and drag,tubing buckling,and pipe stuck probably occur,which results in a lot of non-productive time and remedial operations.Cuttings bed remover can efficiently destroy deposited cuttings in time through hydraulic and mechanical stirring effects.This paper aims to build a method for hole cleaning evaluation and installation spacing optimization of cuttings bed remover to improve the wellbore cleaning effect.Firstly,a Computational Fluid Dynamics approach with Eulerian—Eulerian multiphase model was utilized to investigate the mechanism of cuttings transportation,and a new type of cuttings bed remover was designed.Next,an evaluation method of hole cleaning effect of remover was established.After that,the effects of several drilling parameters on hole cleaning including flow rate of drilling fluid,rotational speed of drillpipe,rate of penetration,wellbore size,rheological property of drilling fluid,and remover eccentricity on the performance of cuttings bed remover were investigated.The results demonstrate that the new type of remover with streamline blade performs better than conventional removers.The efficiency of hole cleaning is greatly improved by increasing the rotational speed of drillpipe,flow rate of drilling fluid,remover eccentricity,and 6 rpm Fann dial reading for drilling fluid.While higher rate of penetration and large wellbore size result in worse hole cleaning.These findings can serve as an important guide for the structure optimization design of cuttings bed remover and installation spacing of removers.

Surface activity and cleaning performance of rosin-based quaternary ammonium salt type asymmetric Gemini surfactants

Rosin,a renewable and abundant resource,has been extensively processed and chemically modified to endow it with special properties,especially in the surfactant industry.In this study,four rosin-based quaternary ammonium asymmetric gemini surfactants(RGS-2-n)with different alkyl chain lengths(n=12,14,16,18)were synthesized using a simple two-step method based on dehydroabietylamine as the raw material.The feasibility of these surfactants for cleaning purposes was comprehensively evaluated,suggesting that the surfactants own high surface activity and good cleaning performance.Furthermore,by successfully introducing the amine group of dehydroabietylamine into the hydrophilic group of the surfactants,we avoided its potential harm to the environment and water pollution.Density functional theory proves rosin-based gemini surfactants with asymmetric structure can further improve cleaning efficiency.Overall,our findings suggests that RGS-2-n surfactants are promising and sustainable candidates for cleaning electric plates,and provide new opportunities for rosin application in the electric industry.

Cleaning of two mirrors in the first mirror unit using radiofrequency capacitively coupled plasma

First mirror(FM)cleaning,using radio frequency(RF)plasma,has been proposed to recover FM reflectivity in nuclear fusion reactors such as the International Thermonuclear Experimental Reactor(ITER).To investigate the influence of simultaneous cleaning of two mirrors on mirror cleaning efficiency and uniformity,experiments involving single-mirror cleaning and dual-mirror cleaning were conducted using RF capacitively coupled plasma in the laboratory.For the test and simultaneous cleaning of two mirrors,the FM and second mirror(SM),both measuring 110 mm×80 mm,were placed inside the first mirror unit(FMU).They were composed of 16 mirror samples,each with a dimension of 27.5 mm×20 mm.These mirror samples consist of a titanium-zirconium-molybdenum alloy substrate,a 500 nm Mo intermediate layer and a 30 nm Al_(2)O_(3) surface coating as a proxy for Be impurities.The cleaning of a single first mirror(SFM)and the simultaneous cleaning of the FM and SM(DFM and DSM)lasted for 9 h using Ar plasma at a pressure of 1 Pa.The total reflectivity of mirror samples on the DSM did not fully recover and varied with location,with a self-bias of−140 V.With a self-bias of−300 V,the total reflectivity of mirror samples on the SFM and DFM was fully recovered.The energy dispersive spectrometer results demonstrated that the Al_(2)O_(3) coating had been completely removed from these mirror samples.However,the mass loss of each mirror sample on the SFM and DFM before and after cleaning varied depending on its location,with higher mass loss observed for mirror samples located in the corners and lower loss for those in the center.Compared with SM cleaning,the simultaneous cleaning of two mirrors reduced the difference between the highest and lowest mass loss.Furthermore,this mass loss for the mirror samples of the DFM facing the DSM was increased.This indicated that mirror samples cleaned face to face in the FMU simultaneously could influence each other,highlighting the need for special attention in future studies.

A method for cleaning wind power anomaly data by combining image processing with community detection algorithms

Current methodologies for cleaning wind power anomaly data exhibit limited capabilities in identifying abnormal data within extensive datasets and struggle to accommodate the considerable variability and intricacy of wind farm data.Consequently,a method for cleaning wind power anomaly data by combining image processing with community detection algorithms(CWPAD-IPCDA)is proposed.To precisely identify and initially clean anomalous data,wind power curve(WPC)images are converted into graph structures,which employ the Louvain community recognition algorithm and graph-theoretic methods for community detection and segmentation.Furthermore,the mathematical morphology operation(MMO)determines the main part of the initially cleaned wind power curve images and maps them back to the normal wind power points to complete the final cleaning.The CWPAD-IPCDA method was applied to clean datasets from 25 wind turbines(WTs)in two wind farms in northwest China to validate its feasibility.A comparison was conducted using density-based spatial clustering of applications with noise(DBSCAN)algorithm,an improved isolation forest algorithm,and an image-based(IB)algorithm.The experimental results demonstrate that the CWPAD-IPCDA method surpasses the other three algorithms,achieving an approximately 7.23%higher average data cleaning rate.The mean value of the sum of the squared errors(SSE)of the dataset after cleaning is approximately 6.887 lower than that of the other algorithms.Moreover,the mean of overall accuracy,as measured by the F1-score,exceeds that of the other methods by approximately 10.49%;this indicates that the CWPAD-IPCDA method is more conducive to improving the accuracy and reliability of wind power curve modeling and wind farm power forecasting.

Investigation of an electrode-driven hydrogen plasma method for in situ cleaning of tin-based contamination

To prolong the service life of optics,the feasibility of in situ cleaning of the multilayer mirror(MLM)of tin and its oxidized contamination was investigated using hydrogen plasma at different power levels.Granular tin-based contamination consisting of micro-and macroparticles was deposited on silicon via physical vapor deposition(PVD).The electrodedriven hydrogen plasma at different power levels was systematically diagnosed using a Langmuir probe and a retarding field ion energy analyzer(RFEA).Moreover,the magnitude of the self-biasing voltage was measured at different power levels,and the peak ion energy was corrected for the difference between the RFEA measurements and the self-biasing voltage(E_(RFEA)-eV_(self)).XPS analysis of O 1s and Sn 3d peaks demonstrated the chemical reduction process after 1 W cleaning.Analysis of surface and cross-section morphology revealed that holes emerged on the upper part of the macroparticles while its bottom remained smooth.Hills and folds appeared on the upper part of the microparticles,confirming the top-down cleaning mode with hydrogen plasma.This study provides an in situ electrode-driven hydrogen plasma etching process for tin-based contamination and will provide meaningful guidance for understanding the chemical mechanism of reduction and etching.

Wellbore Cleaning Degree and Hydraulic Extension in Shale Oil Horizontal Wells

The efficient development and exploitation of shale oil depends on long-distance horizontal wells. As the degreeof cleaning of the wellbore plays a key role in these processes, in this study, this problem is investigated experimentallyby focusing on the dimensionless cuttings bed height. A method is proposed to calculate the horizontalwellhydraulic extension taking into account the influence of the wellbore cleaning degree on the wellborepressure distribution and assess the effect of a variety of factors such as the bottom hole pressure, the circulatingpressure drop, the drilling pump performance and the formation properties. The analysis shows that the hydraulicextension of horizontal wells decreases with an increase in the cuttings bed height, and the higher the displacementof drilling fluid, the faster the hydraulic extension declines. The annular pressure drop of the horizontalsection increases with the increase of the cuttings bed height, resulting in a higher bottom-hole pressure. Severalarguments are provided to guide the safe drilling of shale oil horizontal wells and overcome the limits of currenttechnological approaches.

A Diamond Electrochemical Cleaning Technique for Organic Contaminants on Silicon Wafer Surfaces

Peroxodiphosphate anion （a powerful oxidant） can be formed in a special water-based cleaning agent through an electrochemical reaction on boron-doped diamond electrodes. This electrochemical reaction was applied during the oxidation,decomposition, and removal of organic contaminations on a silicon wafer surface, and it was used as the first step in the diamond electrochemical cleaning technique （DECT）. The cleaning effects of DECT were compared with the RCA cleaning technique, including the silicon surface chemical composition that was observed with X-ray photoelectron spectroscopy and the morphology observed with atomic force microscopy. The measurement results show that the silicon surface cleaned by DECT has slightly less organic residue and lower micro-roughness,so the new technique is more effective than the RCA cleaning technique.

Overview of Factors Affecting Dust Deposition on Photovoltaic Cells and Cleaning Methods

Dust deposition on the surface of photovoltaic (PV) cells poses a significant challenge to their efficiency, especially in arid regions characterized by desert and semi-desert conditions. Despite the pronounced impact of dust accumulation, these regions offer optimal solar radiation and minimal cloud cover, making them ideal candidates for widespread PV cell deployment. Various surface cleaning methods exist, each employing distinct approaches. Choosing an appropriate cleaning method requires a comprehensive understanding of the mechanisms involved in both dust deposition on module surfaces and dust adhesion to PV cell surfaces. The mechanisms governing dust deposition and adhesion are complex and multifaceted, influenced by factors such as the nature and properties of the dust particles, environmental climatic conditions, characteristics of protective coatings, and the specific location of the PV installation. These factors exhibit regional variations, necessitating the implementation of diverse cleaning approaches tailored to the unique conditions of each location. The first part of this article explores the factors influencing dust deposition on PV cell surfaces, delving into the intricate interplay of environmental variables and particle characteristics. Subsequently, the second part addresses various cleaning methods, offering an analysis of their respective advantages and disadvantages. By comprehensively examining the factors influencing dust accumulation and evaluating the effectiveness of different cleaning strategies, this article aims to contribute valuable insights to the ongoing efforts to optimize the performance and longevity of photovoltaic systems in diverse geographical contexts.

Review of Underwater Ship Hull Cleaning Technologies

This paper presents a comprehensive review and analysis of ship hull cleaning technologies.Various cleaning methods and devices applied to dry-dock cleaning and underwater cleaning are introduced in detail,including rotary brushes,high-pressure and cavitation water jet technology,ultrasonic technology,and laser cleaning technology.The application of underwater robot technology in ship cleaning not only frees divers from engaging in heavy work but also creates safe and efficient industrial products.Damage to the underlying coating of the ship caused by the underwater cleaning operation can be minimized by optimizing the working process of the underwater cleaning robot.With regard to the adhesion technology mainly used in underwater robots,an overview of recent developments in permanent magnet and electromagnetic adhesion,negative pressure force adhesion,thrust force adhesion,and biologically inspired adhesion is provided.Through the analysis and comparison of current underwater robot products,this paper predicts that major changes in the application of artificial intelligence and multirobot cooperation,as well as optimization and combination of various technologies in underwater cleaning robots,could be expected to further lead to breakthroughs in developing next-generation robots for underwater cleaning.

An Experimental and Numerical Study on the Cleaning of Pleated Bag Filters Using Low-Pressure Pulsed-Jets

Pulsed-jet cleaning is recognized as the most efficient method to regenerate bag dust collectors traditionally used in industrial processes to control the emission of particulates.In this study,non-woven needle felt filter bags with and without a film coating material have been analyzed considering different geometries(different number N of pairs of pleated filter bag sides)in the frame of dedicated low-pressure pulsed-jet cleaning experiments.The flow structure inside the bag and the response characteristics of its wall have also been analyzed numerically through a computational fluid-dynamics/structural-dynamics(CFD-CSD)unidirectional fluid-solid coupling method.As shown by the experiments,the peak pressure(P_(0))on the wall of the filter bag with N=8 and 12 is higher,which indicates dust can be removed more effectively in these cases.The peak pressure on the wall increases first and then decreases along the direction of the bag length,while the peak pressure of the pleated filter bag with nonwoven needled felt film coating is greater than that without film coating.A comprehensive analysis of the time variation of acceleration,deformation,strain,stress and other factors,has led to the conclusion that the pleated filter bag with N=12 would be the optimal choice.

Technical Regulations on Cleaning Processing of Feeding Millet Seeds in Hebei Province

According to many years of experimental summary, the technical demands, process control, seed test, seed quality and work record （ledger management） of cleaning processing of feeding millet seeds in Hebei Province were studied, and specific measures and technical indicators of the technical regulations were analyzed to provide normalized, standardized, industrial and marketization technical support for the cleaning processing of feeding millet seeds.

Closer Approximation to Optimize Solar Panels Performance with Cleaning Cycle: A Follow-Up

The performance of solar panels significantly degrades due to dust accumulation but cleaning too frequently will severely impact the financial benefits of the installation of solar panels. This paper assumes a realistic linear model for accumulation of dust on the solar panels and the resulting hourly average of absolute loss of efficiency in solar panels. This model accurately depicts the fact that energy production by solar panels occurs during sunshine hours only and also accounts for the degradation in the efficiency of solar panels due to dust accumulation throughout the entire day. Based on this, the optimal number of days for maximum financial profit and the critical number of days (above which there is no profit in installing solar panels) have been estimated. Furthermore, we have suggested a formalism to help estimate the finances for self-cleaning technology for PV system and also for calculating the minimum payback period for installing solar panels with the financial cost of the cleaning cycles properly considered. This research could be motivation for companies in developing self-cleaning mechanism for PV system.

Effect of a disposable endoscope precleaning kit in the cleaning procedure of gastrointestinal endoscope:A multi-center observational study

BACKGROUND Precleaning is a key step in endoscopic reprocessing.AIM To develop an effective and economic endoscope cleaning method by using a disposable endoscope bedside precleaning kit.METHODS Altogether,228 used gastrointestinal endoscopes were selected from five high-volume endoscopy units and precleaned by a traditional precleaning bucket(group T)or a disposable endoscope bedside precleaning kit(group D).Each group was further subdivided based on the replacement frequency of the cleaning solution,which was replaced every time in subgroups T1 and D1 and every several times in subgroups Ts and Ds.The adenosine triphosphate(ATP)level and residual proteins were measured three times:Before and after precleaning and after manual cleaning.RESULTS After precleaning,the precleaning kit significantly reduced the ATP levels(P=0.034)and has a more stable ATP clearance rate than the traditional precleaning bucket.The precleaning kit also saved a quarter of the cost of enzymatic detergent used during the precleaning process.After manual cleaning,the ATP levels were also significantly lower in the precleaning kit group than in the traditional precleaning bucket group(P<0.05).Meanwhile,the number of uses of the cleaning solution(up to four times)has no significant impact on the cleaning effect(P>0.05).CONCLUSION Considering its economic cost and cleaning effect,the use of a disposable endoscope bedside precleaning kit can be an optimal option in the precleaning stage with the cleaning solution being replaced several times in the manual cleaning stage.

Fuzzy prediction and experimental verification of road surface cleaning rate by pure waterjets

The cleaning parameters affecting cleaning rate using pure waterjets to clean road surface was researched. A mathematical model for predicting cleaning rate was established using fuzzy mathematical method. A fuzzy rule base character-izing the relationship between input and output parameters was built through experiments. The prediction of cleaning rate was achieved under the condition of given input parameters by rule-based fuzzy reasoning. The prediction results were analyzed through experimental verification.

Study of Oil-Bearing Drill Cuttings Cleaning and De-Oiling Treatment Method for Shale Gas Reservoirs

Due to its extensive use in shale gas exploration and development,oil-based drilling fluids generate large amounts of oil-bearing drill cuttings during the drilling process.The large amount of oil-bearing drill cuttings generated during the drilling process can lead to serious secondary contamination.In this study,a wetting agent FSC-6 with good hydrophobic and oleophobic properties was synthesized to construct an efficient oil removal system.For the first time,the mechanism of this system was analyzed by using the theory of adhesion function,interfacial tension and wettability.At the same time,a combined acoustic-chemical treatment process was applied to the wastewater and slag generated after the cleaning of the oil-bearing drill cuttings.The experimental results show that the application of this pollution-free technology can effectively solve the environmental pollution and resource recovery problems of oil-bearing drill cuttings.It meets the standard of drilling chips with oil content less than 2%in SY/T7422-2018“Oil-based drilling fluid drilling chips treatment system for oil and gas drilling equipment”.

A Giant of China's Cleaning Industry——The Blue Star Chemical Cleaning Group Corporation

First business: to clean a tea pot. Income: RMB 0.20 (less than 10 US cents at the time). Second business: to clean a boiler. Income: RMB 1, 200. Three months later, incomereached RMB 240, 000. Ten years later, the company had 350 subsidiaries across China and four joint ventures abroad, with an annual output value of more than RMB 300 million. The data are simple but intriguing, recording the history of the Blue

Deep cleaning of a metallurgical zinc leaching residue and recovery of valuable metals

Huge quantities of zinc leaching residues(ZLRs) generated from zinc production are dumped continuously around the world and pose a potential environmental threat because of their considerable amounts of entrained heavy metals(mainly lead). Most ZLRs have not been properly treated and the valuable metals in them have not yet been effectively recovered. Herein, the deep cleaning of a ZLR and recovery of valuable metals via a hydrometallurgical route were investigated. The cleaning process consists of two essential stages: acid leaching followed by calcium chloride leaching. The optimum conditions for extracting zinc, copper, and indium by acid leaching were a sulfuric acid concentration of 200 g·L^(-1), a liquid/solid ratio of 4:1(m L/g), a leaching time of 2 h, and a temperature of 90°C. For lead and silver extractions, the optimum conditions were a calcium chloride concentration of 400 g·L^(-1), a pH value of 1.0, a leaching time of 1 h, and a temperature of 30°C. After calcium chloride leaching, silver and lead were extracted out and the lead was finally recovered as electrolytic lead by electrowinning. The anglesite phase, which poses the greatest potential environmental hazard, was removed from the ZLR after deep cleaning, thus reducing the cost of environmental management of ZLRs. The treatment of chlorine and spent electrolyte generated in the process was discussed.

Modes of Occurrence and Cleaning Potential of Trace Elements in Coals from the Northern Ordos Basin and Shanxi Province, China

Based on the analyses of 43 elements in 16 samples of the raw coal and feed coal collected from the northern Ordos basin and Shanxi Province, the modes of occurrence of these elements were studied using the method of cluster analysis and factor analysis, and the cleaning potential of the hazardous elements relatively enriched in the coals was discussed by analyzing six samples of the cleaned coal from the coal-washing plants and coal cleaning simulation experiments. The results shows that the elements Br and Ba show a strong affinity to the organic matter, Cs, Cd, Pb, Zn and Hg partly to the organic matter, and the other trace elements are mainly associated with the mineral matter. Cs, Mo, P, Pb, Zn and S have positive correlations with the two principal factors, reflecting the complexity of their modes of occurrence. Some elements that were thought to show a faint relationship (Be with S and Sb with carbonates) in other rocks are found to have a strong interrelation in the coals. Clay minerals (mainly kaolinite) dominate in the coals, and Ta, Th, Ti, Sc, REE, Hf, U, Se, W, V, Nb, Mo, Al, P, Cr, Pb and Zn are distributed mostly in kaolinite, while K, Rb, Cs, and Na have much to do with illite. Conventional cleaning can reduce the concentrations of most hazardous elements in various degrees. The hazardous elements S, As, Sb, Se, Mo, Pb, Cd and Hg relatively enriched in some coals from the area studied have a relatively high potential of environmental risks. However, by physical coal cleaning processes, more than 60% of As and Hg were removed, showing a high degree of removal, more than 30% of Sb, as well as S, Pb and Cd partly associated with the inorganic matter were removed. Se and Mo showing a relatively low degree of removal could be further removed by deep crushing of the coal during physical cleaning processes, and the concentrations of S, Pb, Cd and Hg with a partial association with the organic matter could be decreased in such ways as the coal blending. Cluster analysis together with factor analysis is a rapid and effective way to deduce the mode of occurrence of an element from bulk samples, and the removability data of most hazardous elements are basically consistent with their modes of occurrence suggested, which indicates that the statistical analysis could predict the cleaning potential of hazardous elements during the physical coal cleaning.

Simultaneous Optimization of Synthesis and Scheduling of Cleaning in Flexible Heat Exchanger Networks

A novel methodology is presented for simultaneously optimizing synthesis and cleaning schedule of flexible heat exchanger network(HEN)by genetic/simulated annealing algorithms(GA/SA).Through taking into account the effect of fouling process on optimal network topology,a preliminary network structure possessing two-fold oversynthesis is obtained by means of pseudo-temperature enthalpy(T-H)diagram approach prior to simultaneous optimization.Thus,the computational complexity of this problem classified as NP(Non-deterministic Polynomial)-complete can be significantly reduced.The promising matches resulting from preliminary synthesis stage are further optimized in parallel with their heat exchange areas and cleaning schedule.In addition,a novel continu- ous time representation is introduced to subdivide the given time horizon into several variable-size intervals according to operating periods of heat exchangers,and then flexible HEN synthesis can be implemented in dynamic manner.A numerical example is provided to demonstrate that the presented strategy is feasible to decrease the total annual cost(TAC)and further improve network flexibility,but even more important,it may be applied to solve large-scale flexible HEN synthesis problems.

Effect of the Ultrasound Generated by Flat Plate Transducer Cleaning on Polluted Polyvinylidenefluoride Hollow Fiber Ultrafiltration Membrane

Polyvinylidenefluoride （PVDF） hollow fiber ultrafiltration membrane is frequently employed in water treatment. However, the fouling of ultrafiltration membranes affects the economic effectiveness of such process significantly. The ultrasound generated by flat plate transducer （UFPT） was used to clean the polluted PVDF ultrafiltration membrane with 2 g·L^-1 of citric acid aqueous solution in our study. The effects of UFPT intensity on the membrane surface were studied. The new membrane was easy to be polluted by the saturated CaCl2 solution. A synergistic effect of UFPT and 2 g·L^-1 citric acid aqueous solution could remove the foul of the membrane, and its flux could be recovered about 81%. The flux recovery of old membrane polluted was increased to 73.2% after 7 h soaking in citric acid aqueous solution, but its flux recovery without soaking was only increased to 56.2%.