Computational fluid dynamics modeling of rapid pyrolysis of solid waste magnesium nitrate hydrate under different injection methods

This study developed a numerical model to efficiently treat solid waste magnesium nitrate hydrate through multi-step chemical reactions.The model simulates two-phase flow,heat,and mass transfer processes in a pyrolysis furnace to improve the decomposition rate of magnesium nitrate.The performance of multi-nozzle and single-nozzle injection methods was evaluated,and the effects of primary and secondary nozzle flow ratios,velocity ratios,and secondary nozzle inclination angles on the decomposition rate were investigated.Results indicate that multi-nozzle injection has a higher conversion efficiency and decomposition rate than single-nozzle injection,with a 10.3%higher conversion rate under the design parameters.The decomposition rate is primarily dependent on the average residence time of particles,which can be increased by decreasing flow rate and velocity ratios and increasing the inclination angle of secondary nozzles.The optimal parameters are injection flow ratio of 40%,injection velocity ratio of 0.6,and secondary nozzle inclination of 30°,corresponding to a maximum decomposition rate of 99.33%.

Computational fluid dynamics-discrete element method simulation of stirred tank reactor for graphene production

Liquid phase exfoliation(LPE)process for graphene production is usually carried out in stirred tank reactor and the interactions between the solvent and the graphite particles are important as to improve the production efficiency.In this paper,these interactions were revealed by computational fluid dynamics–discrete element method(CFD-DEM)method.Based on simulation results,both liquid phase flow hydrodynamics and particle motion behavior have been analyzed,which gave the general information of the multiphase flow behavior inside the stirred tank reactor as to graphene production.By calculating the threshold at the beginning of graphite exfoliation process,the shear force from the slip velocity was determined as the active force.These results can support the optimization of the graphene production process.

A simplified approach to modelling blasts in computational fluid dynamics (CFD)

This paper presents a time-efficient numerical approach to modelling high explosive(HE)blastwave propagation using Computational Fluid Dynamics(CFD).One of the main issues of using conventional CFD modelling in high explosive simulations is the ability to accurately define the initial blastwave properties that arise from the ignition and consequent explosion.Specialised codes often employ Jones-Wilkins-Lee(JWL)or similar equation of state(EOS)to simulate blasts.However,most available CFD codes are limited in terms of EOS modelling.They are restrictive to the Ideal Gas Law(IGL)for compressible flows,which is generally unsuitable for blast simulations.To this end,this paper presents a numerical approach to simulate blastwave propagation for any generic CFD code using the IGL EOS.A new method known as the Input Cavity Method(ICM)is defined where input conditions of the high explosives are given in the form of pressure,velocity and temperature time-history curves.These time history curves are input at a certain distance from the centre of the charge.It is shown that the ICM numerical method can accurately predict over-pressure and impulse time history at measured locations for the incident,reflective and complex multiple reflection scenarios with high numerical accuracy compared to experimental measurements.The ICM is compared to the Pressure Bubble Method(PBM),a common approach to replicating initial conditions for a high explosive in Finite Volume modelling.It is shown that the ICM outperforms the PBM on multiple fronts,such as peak values and overall overpressure curve shape.Finally,the paper also presents the importance of choosing an appropriate solver between the Pressure Based Solver(PBS)and Density-Based Solver(DBS)and provides the advantages and disadvantages of either choice.In general,it is shown that the PBS can resolve and capture the interactions of blastwaves to a higher degree of resolution than the DBS.This is achieved at a much higher computational cost,showing that the DBS is much preferred for quick turnarounds.

Preliminary Evaluation of Hemodynamic Effects of Fontan Palliation on Renal Artery Using Computational Fluid Dynamics

Background:The assessment of renal function is important to the prognosis of patients needing Fontan palliation due to the reconstructed compromised circulation.To know the relationship between the kidney perfusion and hemodynamic characteristics during surgical design could reduce the risk of acute kidney injury(AKI)and the postoperative complications.However,the issue is still unsolved because the current clinical evaluation methods are unable to predict the hemodynamic changes in renal artery(RA).Methods:We reconstructed a three-dimensional(3D)vascular model of a patient requiring Fontan palliation.The technique of computational fluid dynamics(CFD)was utilized to explore the changes of RA hemodynamics under different possible blood flow rates.The relationship between the kidney perfusion and hemodynamic characteristics was investigated.Results:The calculated results indicated the declined tendency of the pressure and pressure drop as the flow rate decreased.When the flow rate decreased to two-thirds of its baseline,both the pressure of left renal artery(LRA)and the pressure of right renal artery(RRA)dipped below 50%,and the pressure of RRA fell more quickly than that of LRA.Uneven distribution of WSS was observed on the trunk of RA,and the lowest WSS was found at the distal of RA.The average WSS in RA dropped to around 50%as the flow rate reached one-third of its baseline.Conclusions:As a promising approach,CFD can be utilized to quantitatively evaluate the hemodynamic characteristics of RA and contribute to offsetting the drawbacks of clinical assessments of renal function,to help realize better prognosis for the patients with Fontan palliation.

Application of computational fluid dynamics in design of viscous dampers-CFD modeling and full-scale dynamic testing

Computational fluid dynamics(CFD)provides a powerful tool for investigating complicated fluid flows.This paper aims to study the applicability of CFD in the preliminary design of linear and nonlinear fluid viscous dampers.Two fluid viscous dampers were designed based on CFD models.The first device was a linear viscous damper with straight orifices.The second was a nonlinear viscous damper containing a one-way pressure-responsive valve inside its orifices.Both dampers were detailed based on CFD simulations,and their internal fluid flows were investigated.Full-scale specimens of both dampers were manufactured and tested under dynamic loads.According to the tests results,both dampers demonstrate stable cyclic behaviors,and as expected,the nonlinear damper generally tends to dissipate more energy compared to its linear counterpart.Good compatibility was achieved between the experimentally measured damper force-velocity curves and those estimated from CFD analyses.Using a thermography camera,a rise in temperature of the dampers was measured during the tests.It was found that output force of the manufactured devices was virtually independent of temperature even during long duration loadings.Accordingly,temperature dependence can be ignored in CFD models,because a reliable temperature compensator mechanism was used(or intended to be used)by the damper manufacturer.

Application of Computational Fluid Dynamics and Fluid Structure Interaction Techniques for Calculating the 3D Transient Flow of Journal Bearings Coupled with Rotor Systems

Journal bearings are important parts to keep the high dynamic performance of rotor machinery. Some methods have already been proposed to analysis the flow field of journal bearings, and in most of these methods simplified physical model and classic Reynolds equation are always applied. While the application of the general computational fluid dynamics （CFD）-fluid structure interaction （FSI） techniques is more beneficial for analysis of the fluid field in a journal bearing when more detailed solutions are needed. This paper deals with the quasi-coupling calculation of transient fluid dynamics of oil film in journal bearings and rotor dynamics with CFD-FSI techniques. The fluid dynamics of oil film is calculated by applying the so-called ＂dynamic mesh＂ technique. A new mesh movement approacb is presented while the dynamic mesh models provided by FLUENT are not suitable for the transient oil flow in journal bearings. The proposed mesh movement approach is based on the structured mesh. When the joumal moves, the movement distance of every grid in the flow field of bearing can be calculated, and then the update of the volume mesh can be handled automatically by user defined function （UDF）. The journal displacement at each time step is obtained by solving the moving equations of the rotor-bearing system under the known oil film force condition. A case study is carried out to calculate the locus of the journal center and pressure distribution of the journal in order to prove the feasibility of this method. The calculating results indicate that the proposed method can predict the transient flow field of a journal bearing in a rotor-bearing system where more realistic models are involved. The presented calculation method provides a basis for studying the nonlinear dynamic behavior of a general rotor-bearing system.

A Computational Fluid Dynamics (CFD) Analysis of an Undulatory Mechanical Fin Driven by Shape Memory Alloy

Many fishes use undulatory fin to propel themselves in the underwater environment. These locomotor mechanisms have a popular interest to many researchers. In the present study, we perform a three-dimensional unsteady computation of an undulatory mechanical fin that is driven by Shape Memory Alloy （SMA）. The objective of the computation is to investigate the fluid dynamics of force production associated with the undulatory mechanical fin. An unstructured, grid-based, unsteady Navier-Stokes solver with automatic adaptive remeshing is used to compute the unsteady flow around the fin through five complete cycles. The pressure distribution on fin surface is computed and integrated to provide fin forces which are decomposed into lift and thrust. The velocity field is also computed throughout the swimming cycle. Finally, a comparison is conducted to reveal the dynamics of force generation according to the kinematic parameters of the undulatory fin （amplitude, frequency and wavelength）.

COMPUTATIONAL FLUID DYNAMICS(CFD) SIMULATIONS OF DRAG REDUCTION WITH PERIODIC MICRO-STRUCTURED WALL

Computational fluid dynamics（CFD） simulations are adopted to investigate rectangular microchannel flows with various periodic micro-structured wall by introducing velocity slip boundary condition at low Reynolds number. The purpose of the current study is to numerically find out the effects of periodic micro-structured wall on the flow resistance in rectangular microchannel with the different spacings between microridges ranging from 15 to 60 pm. The simulative results indicate that pressure drop with different spacing between microridges increases linearly with flow velocity and decreases monotonically with slip velocity; Pressure drop reduction also increases with the spacing between microridges at the same condition of slip velocity and flow velocity. The results of numerical simulation are compared with theoretical predictions and experimental results in the literatures. It is found that there is qualitative agreement between them.

Computational fluid dynamics evaluation of the effect of different city designs on the wind environment of a downwind natural heritage site

Disturbance in wind regime and sand erosion deposition balance may lead to burial and eventual vanishing of a site.This study conducted 3D computational fluid dynamics(CFD)simulations to evaluate the effect of a proposed city design on the wind environment of the Crescent Spring,a downwind natural heritage site located in Dunhuang,Northwestern China.Satellite terrain data from the Advanced Spaceborne Thermal Emission and Reflection Radiometer(ASTER)Digital Elevation Model(DEM)were used to construct the solid surface model.Steady-state Reynolds Averaged Navier-Stokes equations(RANS)with shear stress transport(SST)k-ωturbulence model were then applied to solve the flow field problems.Land-use changes were modeled implicitly by dividing the underlying surface into different areas and by applying corresponding aerodynamic roughness lengths.Simulations were performed by using cases with different city areas and building heights.Results show that the selected model could capture the surface roughness changes and could adjust wind profile over a large area.Wind profiles varied over the greenfield to the north and over the Gobi land to the east of the spring.Therefore,different wind speed reduction effects were observed from various city construction scenarios.The current city design would lead to about 2 m/s of wind speed reduction at the downwind city edge and about 1 m/s of wind speed reduction at the north of the spring at 35-m height.Reducing the city height in the north greenfield area could efficiently eliminate the negative effects of wind spee.By contrast,restricting the city area worked better in the eastern Gobi area compared with other parts of the study area.Wind speed reduction in areas near the spring could be limited to 0.1 m/s by combining these two abatement strategies.The CFD method could be applied to simulate the wind environment affected by other land-use changes over a large terrain.

Characterization of the Engineering Flow in a Miniaturised Bioreactor by Computational Fluid Dynamics

Three approaches based on computational fluid dynamics(CFD) techniques have been assessed for their ability to describe the engineering flow environment in a miniaturized mechanically agitated bioreactor. The three approaches tested were the source-sink(SS), the multiple reference frames(MRF) and the sliding grids(SG). In all the cases, the predictions of the velocity components agree with reported experimental data. However, the analysis of the results of the turbulent intensities predicted by the three approaches indicates the MRF and the SG techniques under predicted turbulent intensities are comparable to both experimental measurements and the SS method. The predicted power number and pumping number based on the SS approach are closer to typical reported experimental values compared to those obtained from the MRF and SG methods.

Application of computational fluid dynamics simulation for submarine oil spill

Computational fluid dynamics （CFD） codes are being increasingly used in the simulation of submarine oil spills. This study focuses on the process of oil spills, from damaged submarine pipes, to the sea surface, using numerical models. The underwater oil spill model is developed, and a description of the governing equations is proposed, along with modifications required for the particalization of the control volume. Available experimental data were introduced to evaluate the validity of the CFD predictions, the results of which proved to be in good agreement with the experimental data. The effects of oil leak rate, leak diameter, current velocity, and oil density are investigated, by the validated CFD model, to estimate the undersea leakage time, the lateral migration distance, and surface diffusion range when the oil reaches the sea surface. Results indicate that the leakage time and lateral migration distance increase with decreasing leak rates and leak diameter, and increase with increasing current velocity and oil density. On the other hand, a large leak diameter, high density, high leak rate, or fast currents result in a greater surface diffusion range. The findings and analysis presented here will provide practical predictions of oil spills, and guidance for emergency rescues.

COMPUTATIONAL FLUID DYNAMICS RESEARCH ON PRESSURE LOSS OF CROSS-FLOW PERFORATED MUFFLER

The pressure loss of cross-flow perforated of physical modeling, simulation and data processing. muffler has been computed with the procedure Three-dimensional computational fluid dynamics （CFD） has been used to investigate the relations of porosities, flow velocity and diameter of the holes with the pressure loss. Accordingly, some preliminary results have been obtained that pressure loss increases with porosity descent as nearly a hyperbolic trend, rising flow velocity of the input makes the pressure loss increasing with parabola trend, diameter of holes affects little about pressure loss of the muffler. Otherwise, the holes on the perforated pipes make the air flow gently and meanly, which decreases the air impact to the wall and pipes in the muffler. A practical perforated muffler is used to illustrate the available of this method for pressure loss computation, and the comparison shows that the computation results with the method of CFD has reference value for muffler design.

Simplifi ed dynamic analysis to evaluate liquefaction-inducedlateral deformation of earth slopes: a computational fluid dynamics approach

Lateral deformation of liquefiable soil is a cause of much damage during earthquakes, reportedly more than other forms of liquefaction-induced ground failures. Researchers have presented studies in which the liquefied soil is considered as viscous fluid. In this manner, the liquefied soil behaves as non-Newtonian fluid, whose viscosity decreases as the shear strain rate increases. The current study incorporates computational fluid dynamics to propose a simplified dynamic analysis for the liquefaction-induced lateral deformation of earth slopes. The numerical procedure involves a quasi-linear elastic model for small to moderate strains and a Bingham fluid model for large strain states during liquefaction. An iterative procedure is considered to estimate the strain-compatible shear stiffness of soil. The post-liquefaction residual strength of soil is considered as the initial Bingham viscosity. Performance of the numerical procedure is examined by using the results of centrifuge model and shaking table tests together with some field observations of lateral ground deformation. The results demonstrate that the proposed procedure predicts the time history of lateral ground deformation with a reasonable degree of precision.

Optimization of the Internal Circulating Fluidized Bed Using Computational Fluid Dynamics Technology

The computational fluid dynamics(CFD)technology is analyzed and calculated utilizing the turbulence model and multiphase flow model to explore the performance of internal circulating fluidized beds(ICFB)based on CFD.The three-dimensional simulation method can study the hydrodynamic properties of the ICFB,and the performance of the fluidized bed is optimized.The fluidization performance of the ICFB is improved through the experimental study of the cross-shaped baffle.Then,through the cross-shaped baffle and funnel-shaped baffle placement,the fluidized bed reaches a coupled optimization.The results show that CFD simulation technology can effectively improve the mass transfer efficiency and performance of sewage treatment.The base gap crossshaped baffle can improve the hydraulic conditions of the fluidized bed and reduce the system energy consumption.The cross-shaped baffle and funnel-shaped baffle can perfect the performance of the reactor and effectively strengthen the treatment in the intense aerobic process of industrial sewage.

Computational Fluid Dynamics Simulation of the Upper Airway of Obstructive Sleep Apnea Syndrome by Muller Maneuver

This study aimed to use computer simulation to describe the fluid dynamic characteristics in patients with obstructive sleep apnea syndrome（OSAS） and to evaluate the difference between during quiet respiration and the Muller maneuver（MM）. Seven patients with OSAS were involved to perform computed tomographic（CT） scanning during quiet respiration and the MM. CT data in DICOM format were transformed into an anatomically three-dimensional computational fluid dynamics（CFD） model of the upper airway. The velocity magnitude, relative pressure, and flow distribution were obtained. Numerical simulation of airflow was performed to discuss how the MM affected airflow in the upper airway. To measure the discrepancy, the SPSS19.0 software package was utilized for statistic analysis. The results showed that the shape of the upper airway became narrower, and the pressure decreased during the MM. The minimal cross-sectional area（MCSA） of velopharynx was significantly decreased（P〈0.05） and the airflow velocity in MCSAs of velopharynx and glossopharynx significantly accelerated（P〈0.05） during the MM. This study demonstrated the possibility of CFD model combined with the MM for understanding pharyngeal aerodynamics in the pathophysiology of OSAS.

Flow Field and Temperature Field in GaN-MOCVD Reactor Based on Computational Fluid Dynamics Modeling

Metal organic chenlical vapor deposition （AIOCVD） growth systems arc one of the. main types of equipment used for growing single crystal materials, such as GaN. To obtain fihn epitaxial materials with uniform performanee, the flow field and ternperature field in a GaN-MOCVD reactor are investigated by modeling and simulating. To make the simulation results more consistent with the actual situation, the gases in the reactor are considered to be compressible, making it possible to investigate the distributions of gas density and pressure in the reactor. The computational fluid dynamics method is used to stud,v the effects of inlet gas flow velocity, pressure in the reactor, rotational speed of graphite susceptor, and gases used in the growth, which has great guiding~ significance for the growth of GaN fihn materials.

Review:Recent Development of High⁃Order⁃Spectral Method Combined with Computational Fluid Dynamics Method for Wave⁃Structure Interactions

The present paper reviews the recent developments of a high⁃order⁃spectral method(HOS)and the combination with computational fluid dynamics(CFD)method for wave⁃structure interactions.As the numerical simulations of wave⁃structure interaction require efficiency and accuracy,as well as the ability in calculating in open sea states,the HOS method has its strength in both generating extreme waves in open seas and fast convergence in simulations,while computational fluid dynamics(CFD)method has its advantages in simulating violent wave⁃structure interactions.This paper provides the new thoughts for fast and accurate simulations,as well as the future work on innovations in fine fluid field of numerical simulations.

NUMERICAL SIMULATION BY COMPUTATIONAL FLUID DYNAMICS AND EXPERIMENTAL STUDY ON STIRRED BIOREACTOR WITH PUNCHED IMPELLER

Instantaneous flow field and temperature field of the two-phase fluid are measured by particle image velocimetry （PIV） and steady state method during the state of onflow. A turbulent two-phase fluid model of stirred bioreactor with punched impeller is established by the computational fluid dynamics （CFD）, using a rotating coordinate system and sliding mesh to describe the relative motion between impeller and baffles. The simulation and experiment results of flow and temperature field prove their warps are less than 10% and the mathematic model can well simulate the fields, which will also provide the study on optimized-design and scale-up of bioreactors with reference value.

Design and Computational Fluid Dynamics Modeling for a Municipal Solid Waste Incineration Process

Municipal Solid Waste (MSW) incineration is among the important opportunities to control the pollutions caused by improper dumping and flue gas emissions so as to meet the environmental guidelines. The objective of this study was to design and develop a model for the MSW incineration process. The paper explains the design and development of MSW incinerator involving details of the Computational Fluid Dynamics (CFD) procedures through model design to the post process. CFD model was developed to reveal these features of the incineration process in the MSW incinerator. The model predicts the temperature in combustion chambers as well as at stack outlet of the incinerator. The solid waste characterization was done, and the laboratory analysis shows that, the Higher Heating Value (HHV) of the MSW is 11.65 MJ/kg on dry basis. The elemental composition MSW consists of 54.8%, 5.27%, 34.61%, 2.37% and 0.3% for Carbon, Hydrogen, Oxygen, Nitrogen and Sulphur respectively which are the input parameters for the CFD. The model simulation was positively achieved during combustion process and temperature in combustion chambers ranged between 930 K and 1700 K.

A computational fluid dynamics investigation of a novel flooded-bed dust scrubber with vibrating mesh

This work proposes a vibrating mesh screen as an alternative to the static mesh screen currently used in conventional flooded-bed dust scrubbers for removing airborne coal mine dust in the continuous mining environment.Fundamental assessments suggest that a vibrating screen may improve the dust collection efficiency of scrubber systems and mitigate the clogging issues associated with the conventional design.To evaluate this hypothesis,computational fluid dynamics(CFD)simulations were carried out to assess the effects of vibration conditions(i.e.,frequency and amplitude)on the dust particle-mesh interaction and mesh wetting conditions,which are the two decisive factors in determining the dust collection efficiency.The results suggest that the vibrating mesh screen can enhance dust particle collision opportunities on the mesh and increase mesh wetted area as compared to the static mesh screen.The effects of mesh screen aperture,coal dust concentration,and spray nozzle flow rate on the performance of the vibrating mesh are also evaluated.Finally,a simplified three-phase flow simulation including airflow,dust particles,and water droplet spray is performed,and the results reflect a significant improvement of dust collection efficiency in the liquid-coated vibrating mesh screen.