Deterioration of dynamic mechanical property of concrete with mineral admixtures under fatigue loading

The dynamic mechanical property of concrete is one of the key parameters,which greatly influences durability of infrastructures subjected to continuous heavy loading,such as girder and track slab of high-speed railway foundation structure.This paper reports serials of experiments designed to investigate the deterioration of dynamic mechanical properties of different concretes under fatigue loading condition.Four parameters including relative dynamic elastic modulus(RDEM),relative dynamic shear modulus(RDSM),relative compressive strength(RCS)and water absorption(WA)of concrete were evaluated to assess the dynamic properties and microstructures of concretes.Results show that the fatigue stress levels and fatigue cycle durations significantly influence the dynamic mechanical properties of concrete including dynamic elastic modulus and dynamic shear modulus.Addition of proper mineral admixture can improve the dynamic mechanical characteristics of concrete and increase its resistance against the fatigue loading effect.Keeping the amount of mineral admixture in concrete constant,its dynamic mechanical property with fly ash is lower than that with fly ash and silica fume.The water absorption in concrete,which is an indirect parameter reflecting capillary porosity,increases evidently after bearing fatigue-loading.There is a close correlation between the deterioration of dynamic mechanical property and the increasing of water absorption of concrete.This indicates that the damage of microstructure of concrete subjected to fatigue loading is the indispensable reason for the decay of its dynamic mechanical performance.

Experimental study of the dynamic mechanical responses and failure characteristics of coal under true triaxial confinements

Investigations on the dynamic mechanical properties and failure mechanisms of coal under in-situ stress is essential for the prevention of dynamic disasters in deep coal mines.Thus,a modified true triaxial Hopkinson bar was employed to explore the dynamic mechanical behaviors of coal at different confining pressures(0–20 MPa)and strain rates(40–220 s^(-1)).The results show that the dynamic peak stress is positively correlated with lateral static pre-stressσy andσz,but negatively correlated with axial static prestressσx.At approximate strain rates,increasing the lateral static pre-stress facilitates increasing the dynamic peak stress,but the minimum lateral static pre-stress is the primary factor limiting a significant increase in dynamic peak stress of coal.Furthermore,the dynamic differential stress is linearly related to the logarithm of strain rate,and the peak strain varies linearly with strain rate.However,there is no significant correlation between confining pressure and peak strain.Moreover,X-ray CT images and photographic fracture observations of coal samples show the failure patterns under uniaxial and triaxial conditions are splitting failure and shear failure,respectively.The device provides a viable approach for fully comprehending the dynamic mechanical behaviors of rock-like material in complex stress conditions.

Dynamic mechanical characteristics of frozen subgrade soil subjected to freeze-thaw cycles

As a widely-applied engineering material in cold regions, the frozen subgrade soils are usually subjected to seismic loading, which are also dramatically influenced by the freeze-thaw(F-T)cycles due to the varying temperature. A series of dynamic cyclic triaxial experiments were conducted through a cryogenic triaxial apparatus for exploring the influences of F-T cycles on the dynamic mechanical properties of frozen subgrade clay.According to the experimental results of frozen clay at the temperature of-10℃, the dynamic responses and microstructure variation at different times of F-T cycles(0, 1, 5, and 20 cycles) were explored in detail.It is experimentally demonstrated that the dynamic stress-strain curves and dynamic volumetric strain curves of frozen clay are significantly sparse after 20F-T cycles. Meanwhile, the cyclic number at failure(Nf) of the frozen specimen reduces by 89% after 20freeze-thaw cycles at a low ratio of the dynamic stress amplitude. In addition, with the increasing F-T cycles,the axial accumulative strain, residual deformation,and the value of damage variable of frozen clay increase, while the dynamic resilient modulus and dynamic strength decrease. Finally, the influence of the F-T cycles on the failure mechanisms of frozen clay was discussed in terms of the microstructure variation. These studies contribute to a better understanding of the fundamental changes in the dynamic mechanical of frozen soils exposed to F-T cycles in cold and seismic regions.

Microscopic damage and dynamic mechanical properties of rock under freeze-thaw environment

For understanding the rock microscopic damage and dynamic mechanical properties subjected to recurrent freeze-thaw cycles, experiments for five groups of homogeneous sandstone under different freeze-thaw cycles were conducted. After freezethaw, nuclear magnetic resonance(NMR) tests and impact loading tests were carried out, from which microscopic damage characteristics of sandstone and dynamic mechanical parameters were obtained. The results indicate that the porosity increases with the increase of cycle number, the rate of porosity growth descends at the beginning of freeze-thaw, yet accelerates after a certain number of cycles. The proportion of pores with different sizes changes dynamically and the multi-scale distribution of pores tends to develop on pore structure with the continuing impact of freeze-thaw and thawing. Dynamic compressive stress-strain curve of sandstone undergoing freeze-thaw can be divided into four phases, and the phase of compaction is inconspicuous compared with the static curve. Elastic modulus and dynamic peak intensity of sandstone gradually decrease with freeze-thaw cycles, while peak strain increases. The higher the porosity is, the more serious the degradation of dynamic intensity is. The porosity is of a polynomial relationship with the dynamic peak intensity.

Dynamic mechanical properties and constitutive equations of 2519A aluminum alloy

To analyze the effects of strain rate and temperature on the flow stress of 2519A aluminum alloy, the dynamic mechanical properties of 2519A aluminum alloy were measured by dynamic impact tests and quasi-static tensile tests. The effects of strain rate and temperature on the microstructure evolution were investigated by optical microscopy （OM） and transmission electron microscopy （TEM）. The experimental results indicate that 2519A aluminum alloy exhibits strain-rate dependence and temperature susceptibility under dynamic impact. The constitutive constants for Johnson--Cook material model were determined by the quasi-static tests and Hopkinson bar experiments using the methods of variable separation and nonlinear fitting. The constitutive equation seems to be consistent with the experimental results, which provides reference for mechanical characteristics and numerical simulation of ballistic performance.

Temperature Dependency of Dynamic Mechanical Properties of Cement Asphalt Paste by DMTA Method

We investigated the temperature dependency of the dynamic mechanical properties of cement asphalt paste by the dynamic mechanical thermal analysis（DMTA） method. The experimental results show that the dynamic mechanical properties of cement asphalt pastes are sensitive to temperature due to the inclusion of asphalt, and may go through different states within a temperature range of-40 ℃ to 60 ℃, which is different from that of pure cement and asphalt. As the temperature of the cement asphalt paste increases, a considerable change of dynamic mechanical properties, including storage modulus（E＇）, loss modulus（E＇＇） and loss factor（tand） is observed. Moreover, the influence of asphalt to cement（A/C） ratio on the temperature sensitivity of the dynamic mechanical properties of cement asphalt composites was investigated. The temperature dependency of cement asphalt composites is ascribed to the temperature dependency of the asphalt and its interaction with cement paste. A simple fractional model is proposed to describe the viscoelastic behavior of cement asphalt composites.

DynamicMechanical and Chemorheology Analysis for the Blended Epoxy System with Polyurethane Modified Resin

As the important matrix material,epoxy resin has been widely used in the composites for various fields.On account of the poor toughness of epoxy resin limiting their suitability for advanced applications,considerable interests have been conducted to modify the epoxy resin to meet the engineering requirements.In this study,the bio-based polyurethane(PU)modified resin was adopted to modify the pure bisphenol-A epoxy by blending method with various proportions.Aiming to illuminate the curing behavior,mechanical and thermal properties,the blended epoxy systems were characterized by viscosity-time analysis,dynamic mechanical analysis(DMA)at different frequencies and temperatures,mechanical tensile test,thermogravimetric analysis(TGA)and Fourier transform infrared(FT-IR)spectroscopy.The results indicated that the introduction of PU modified epoxy was found to significantly inhibit the viscosity growth rates especially when the content of PU modified epoxy resin is higher than 60%.Notwithstanding the dynamic modulus and T_(g)reduced with the increment of PU modified epoxy,remarkable increment on the elongation at break was found and the flexibility was greatly promoted with the introduction of PU modified epoxy.The proportion of PU modified epoxy in the blends should be put balance considerations to obtain optimal mechanical properties.TGA results and FTIR spectrum demonstrated that the addition of PU modified epoxy did not change the thermal decomposition mechanism and chemical reaction mechanism,but the addition of PU modified epoxy inhibits the curing reaction of epoxy resin by measured and calculated the damping temperature domain
T from 35.7℃ to 48.9℃.

Dynamic mechanical properties of PTFE-based composites filled with multi-component

To improve performance of PTFE-based damping material,composites with several fillers were prepared by compressing and sintering. The dynamic mechanical properties of the composites were investigated by means of viscoanalyser. Temperature-dependent loss factors,storage modulus and loss modulus were obtained. And SEM was employed to study the compatibility between PTFE and fillers. The results show that,when blending PPS and PEEK at proper content,the loss factor curve appears double peaks,which can widen the high-damping temperature region of the composites. Blending graphite or alumina can increase the storage modulus obviously,but decrease the value of loss factor. And because graphite or alumina combines with matrix poorly,glide would happen at interface when bearing external load. The interface friction can dissipate vibration energy,which increases the loss modulus of the composites. Blending PPS,PEEK and graphite or alumina at right content,PTFE-based composites can meet demands as damping material in practical engineering.

Dynamic Mechanical Characteristics and Damage Evolution Model of Granite

By using the technique of the split Hopkinson pressure bar（ SHPB）,impact tests at different stress wavelengths（ 0. 8-2. 0 m） and strain rates（ 20-120 s^（-1）） were conducted to study the dynamic mechanical properties and damage accumulation evolution lawof granite. Test results showthat the dynamic compressive strength and strain rate of granite have a significantly exponential correlation;the relationship between peak strain and strain rate is approximately linear,and the increase of wavelengths generally makes the level of peak strain uplift. The multiple-impacts test at a lowstrain rate indicates that at the same wavelength,the cumulative damage of granite shows an exponential increasing form with the increase of strain rate; when keeping the increase of strain rate constant and increasing the stress wavelength,the damage accumulation effect of granite is intensified and still shows an exponential increasing form; under the effect of multiple impacts,the damage development trend of granite is similar overall,but the increase rate is accelerating. Therefore the damage evolution model was established on the basis of the exponential function while the physical meaning of parameters in the model was determined. The model can reflect the effect of the wave parameters and multiple impacts. The validity of the model and the physical meaning of the parameters were verified by the test,which further offer a reference for correlational research and engineering application for the granite.

Dynamic mechanical properties and instability behavior of layered backfill under intermediate strain rates

To obtain dynamic mechanical properties and failure rule of layered backfill under strain rates from10to80s-1,impactloading test on layered backfill specimens(LBS)was conducted by using split Hopkinson pressure bar system.The results indicatethat positive correlation can be found between dynamic compressive strength and strain rate,as well as between strength increasefactor and strain rate.Dynamic compressive strength of LBS gets higher as the arithmetic average cement-sand ratio increases.Compared with static compressive strength,dynamic compressive strength of LBS is enhanced by11%to163%.In addition,theenergy dissipating rate of LBS lies between that of corresponding single specimens,and it decreases as the average cement contentincreases.Deformation of LBS shows obvious discontinuity,deformation degree of lower strength part of LBS is generally higherthan that of higher strength part.A revised brittle fracture criterion based on the Stenerding-Lehnigk criterion is applied to analyzingthe fracture status of LBS,and the average relevant errors of the3groups between the test results and calculation results are4.80%,3.89%and4.66%,respectively.

Investigating the dynamic mechanical behaviors of polyurea through experimentation and modeling

Polyurea is widely employed as a protective coating in many fields because of its superior ability to improve the anti-blast and anti-impact capability of structures.In this study,the mechanical properties of polyurea XS-350 were investigated via systematic experimentation over a wide range of strain rates(0.001-7000 s^-1)by using an MTS,Instron VHS,and split-Hopkinson bars.The stress-strain behavior of polyurea was obtained for various strain rates,and the effects of strain rate on the primary mechanical properties were analyzed.Additionally,a modified rate-dependent constitutive model is proposed based on the nine-parameter Mooney-Rivlin model.The results show that the stress-strain curves can be divided into three distinct regions:the linear-elastic stage,the highly elastic stage,and an approximate linear region terminating in fracture.The mechanical properties of the polyurea material were found to be highly dependent on the strain rate.Furthermore,a comparison between model predictions and the experimental stress-strain curves demonstrated that the proposed model can characterize the mechanical properties of polyurea over a wide range of strain rates.

Effect of Gd content on microstructure and dynamic mechanical properties of solution-treated Mg−xGd−3Y−0.5Zr alloy

The effect of Gd content ranging from 6.5 wt.%to 8.5 wt.%on microstructure evolution and dynamic mechanical behavior of Mg−xGd−3Y−0.5Zr alloys was investigated by optical microscopy,X-ray diffraction,scanning electron microscopy and split Hopkinson pressure bar.The microstructure of as-cast Mg−xGd−3Y−0.5Zr alloys indicates that the addition of Gd can promote grain refinement in the casting.Due to the rapid cooling rate during solidification,a large amount of non-equilibrium eutectic phase Mg_(24)(Gd,Y)_(5) appears at the grain boundary of as-cast Mg−xGd−3Y−0.5Zr alloys.After solution treatment at 520℃ for 6 h,the Mg_(24)(Gd,Y)_(5) phase dissolves into the matrix,and the rare earth hydrides(REH)phase appears.The stress−strain curves validate that the solution-treated Mg−xGd−3Y−0.5Zr alloys with optimal Gd contents maintain excellent dynamic properties at different strain rates.It was concluded that the variation of Gd content and the agglomeration of residual REH particles and dynamically precipitated fine particles are key factors affecting dynamic mechanical properties of Mg−xGd−3Y−0.5Zr alloys.

Combined effects of temperature and axial pressure on dynamic mechanical properties of granite

In order to get the dynamic mechanical properties of deep rock mass suffered both high temperature and high pressure,impact loading experiments on granite subjected to temperature and axial pressure were carried out. Furthermore, the internalstructure characteristics of granite under different temperatures were observed by scanning electron microscopy (SEM). The results show that the longitudinal wave velocity assumes a downward trend which shows a rapid drop before falling slowly as the temperature increases. The uniaxial compressive strength of the specimen decreases significantly at temperatures of 25?100 °C compared to that at temperatures of 100?300 °C. The peak strain rises rapidly before the dividing point of 100 °C, but increases slowly after the dividing point. The internal structure of the rock changes substantially as the temperature increases, such as the extension and transfixion of primary and newborn cracks. In addition, the thermal damage under axial pressure is greater than that described by the longitudinal wave velocity and the phenomenon shows obviously when the temperature increases.

Microstructure Evolution and Dynamic Mechanical Properties of Laser Additive Manufacturing Ti-6Al-4V Under High Strain Rate

The dynamic mechanical properties of the Ti-6Al-4V(TC4)alloy prepared by laser additive manufacturing(LAM-TC4)under the high strain rate(HSR)are proposed.The dynamic compression experiments of LAM-TC4 are conducted with the split Hopkinson pressure bar(SHPB)equipment.The results show that as the strain rate increases,the widths of the adiabatic shear band(ASB),the micro-hardness,the degree of grain refinement near the ASB,and the dislocation density of grains grow gradually.Moreover,the increase of dislocation density of grains is the root factor in enhancing the yield strength of LAM-TC4.Meanwhile,the heat produced from the distortion and dislocations of grains promotes the heat softening effect favorable for the recrystallization of grains,resulting in the grain refinement of ASB.Furthermore,the contrastive analysis between LAM-TC4 and TC4 prepared by forging(F-TC4)indicates that under the HSR,the yield strength of LAM-TC4 is higher than that of F-TC4.

Effect of Thermal Crosslink Conditions on Dynamic Mechanical Behaviors of Flexible Epoxy

The dynamic mechanical behavior of a new kind of flexible epoxy FE-1,which was crosslinked under four different thermal crosslink conditions,was studied.Dynamic mechanical measurement was carried out from 10 ℃ to 120 ℃,and loss factor,tan δ and the storagemodulus as functions of temperature were presented under five different frequencies of 0.1 Hz, 1 Hz,5 Hz,50 Hz and 100 Hz. The experimental results show that temperature has dramatic effects on the dynamic mechanical behavior of flexible epoxy. Compared with other common available epoxy, the flexible epoxy has higher loss factor over broad frequency and common temperature range. Activation energy corresponding to glass transition process of FE-1 was calculated from the temperature corresponding to tan 8 rna~ values, obtained at different measurement frequencies. The maximum value of loss factor is 0.75 and the Tg varies from 6 ℃ to 50 ℃, indicating the flexible epoxy can be used as damping polymer materials at common temperature or frequency range.

The study of measuring technology on the dynamic mechanical properties of welded joint with high strainrate

In this paper, to meet the needs of studying work of dynamic mechanical properties of welded joint, the dynamic mechanical properties of welded joint were measured by means of SHPB(Split Hopkinson Pressure Bar).The dynamic mechanical property's curves of every part of welded joint were obtained. For studying the dynamic behavior of mechanical heterogeneity of welded joint, important data were offered. The method of test creates a new way of studying dynamic mechanical properties of welded joint.

Dynamic compressive response of porcine muscle measured using a split Hopkinson bar system with a pair of PVDF force transducers

The classic metallic Split Hopkinson Pressure Bar(SHPB)cannot capture the transmitted signal accurately when measuring soft biological tissue,because of the very low wave impedance and strength of this material.So the dynamic compressive response of porcine muscle has been investigated by using a modified SHPB.The forces on both ends of the sample measured using Polyvinylidene fluor(PVDF)transducers were applied to calculate the stress in the specimen instead of the strain gauge signal on the transmitted bar.Moreover,a circular cardboard disk pulse shaper was applied for generating a suitable incident pulse to achieve stress equilibrium and constant strain rates in the specimens.Then,the dynamic mechanical properties of porcine muscle parallel and perpendicular to the fiber directions were measured,and the stress equilibrium process during loading was analyzed,as well as the inertia-induced extra stress being corrected.Furthermore,quasi-static tests were conducted at two different strain rates to investigate the strain rate dependence using a universal material testing machine.The results show that the stress-strain curves are sensitive to strain rate in the two different loading directions.The compressive stress perpendicular to the fiber direction is stiffer than that parallel to the fiber direction.In addition,a strain rate-dependent constitutive model was developed based on the mechanical response of the muscle at different strain rates and fitted to the experimental data.The results show that the overall fit is good,and the constitutive model could describe the muscle's dynamic mechanical properties.

EFFECTS OF MOLECULE AGGREGATION STATE OF HINDERED PHENOL ON DYNAMIC MECHANICAL PROPERTIES OF CHLORINATED POLYETHYLENE

Hindered phenol compound 3,9-bis{1,1-dimethyl-2[β-(3-tert-butyl-4-hydroxy-5-methylphenyl)propionyloxy]ethyl}- 2,4,8,10-tetraoxaspiro[5,5]-undecane (AO-80) is a polymorphous material with different physical structures. The initial AO- 80 is highly crystalline, whereas AO-80 obtained by cooling from its molten state is an amorphous material. Annealing treatment below the melting point of AO-80 results in structural development. The mixture of chlorinated polyethylene (CPE) and vitrified AO-80 particles exhibits a dramatic change in the dynamic mechanical properties during heat treatment at 130'C. This change can be attributed to the decomposition of the vitrified AO-80 particles and the hybridization of two constituents. The vitrified AO-80 particles can crystallize again in a CPE matrix by annealing at 100'C, but this crystal is different from that of the initial AO-80 in its microstructure. In addition, the incorporation of CPE chains caused a dramatic increase in the modulus. As a result, the AO-80 crystal particles that contain some CPE chains act as multifunctional cross- links and the CPE/AO-80 hybrid was found to be a new type of elastomer.

The Effect of Fibre Length on Flexural and Dynamic Mechanical Properties of Pineapple Leaf Fibre Composites

The present paper deals with the effect of loading different pineapple leaf fibre(PALF)length(short,mixed and long fibres)and their reinforcement for the fabrication of vinyl ester(VE)composites.Performance of PALF/VE composites was investigated through three-point bending flexural testing and viscoelastic(dynamic)mechanical properties through dynamic mechanical analysis(DMA).DMA results revealed that the long PALF/VE composites displayed better mechanical,damping factor and dynamic properties as compared to the short and mixed PALF/VE composites.The flexural strength and modulus of long PALF/VE composites were 113.5 MPa and 14.3 GPa,respectively.The storage(E′)and loss(E″)moduli increased to 2000 MPa and 225 MPa respectively for PALF/VE composites.Overall result analysis indicated that increasing the length of the reinforcement fibre results in satisfactory mechanical performance and dynamic properties of composites.

Effects of thermal treatment on physical and mechanical characteristics of coal rock

To study the physical and mechanical properties of coal rock after treatment at different temperatures under impact loading, dynamic compression experiments were conducted by using a split Hopkinson pressure bar(SHPB). The stress–strain curves of specimens under impact loading were obtained, and then four indexes affected by temperature were analyzed in the experiment: the longitudinal wave velocity, elastic modulus, peak stress and peak strain. Among these indexes, the elastic modulus was utilized to express the specimens' damage characteristics. The results show that the stress–strain curves under impact loading lack the stage of micro-fissure closure and the slope of the elastic deformation stage is higher than that under static loading. Due to the dynamic loading effect, the peak stress increases while peak strain decreases. The dynamic mechanical properties of coal rock show obvious temperature effects. The longitudinal wave velocity, elastic modulus and peak stress all decrease to different extents with increasing temperature, while the peak strain increases continuously. During the whole heating process, the thermal damage value continues to increase linearly, which indicates that the internal structure of coal rock is gradually damaged by high temperature.