Effects of acid-rock reaction on physical properties during CO_(2)-rich industrial waste gas(CO_(2)-rich IWG)injection in shale reservoirs

"Carbon peaking and carbon neutrality"is an essential national strategy,and the geological storage and utilization of CO_(2)is a hot issue today.However,due to the scarcity of pure CO_(2)gas sources in China and the high cost of CO_(2)capture,CO_(2)-rich industrial waste gas(CO_(2)-rich IWG)is gradually emerging into the public's gaze.CO_(2)has good adsorption properties on shale surfaces,but acidic gases can react with shale,so the mechanism of the CO_(2)-rich IWG-water-shale reaction and the change in reservoir properties will determine the stability of geological storage.Therefore,based on the mineral composition of the Longmaxi Formation shale,this study constructs a thermodynamic equilibrium model of water-rock reactions and simulates the regularity of reactions between CO_(2)-rich IWG and shale minerals.The results indicate that CO_(2)consumed 12%after reaction,and impurity gases in the CO_(2)-rich IWG can be dissolved entirely,thus demonstrating the feasibility of treating IWG through water-rock reactions.Since IWG inhibits the dissolution of CO_(2),the optimal composition of CO_(2)-rich IWG is 95%CO_(2)and 5%IWG when CO_(2)geological storage is the main goal.In contrast,when the main goal is the geological storage of total CO_(2)-rich IWG or impurity gas,the optimal CO_(2)-rich IWG composition is 50%CO_(2)and 50%IWG.In the CO_(2)-rich IWG-water-shale reaction,temperature has less influence on the water-rock reaction,while pressure is the most important parameter.SO2 has the greatest impact on water-rock reaction in gas.For minerals,clay minerals such as illite and montmorillonite had a significant effect on water-rock reaction.The overall reaction is dominated by precipitation and the volume of the rock skeleton has increased by 0.74 cm3,resulting in a decrease in shale porosity,which enhances the stability of CO_(2)geological storage to some extent.During the reaction between CO_(2)-rich IWG-water-shale at simulated temperatures and pressures,precipitation is the main reaction,and shale porosity decreases.However,as the reservoir water content increases,the reaction will first dissolve and then precipitate before dissolving again.When the water content is less than 0.0005 kg or greater than 0.4 kg,it will lead to an increase in reservoir porosity,which ultimately reduces the long-term geological storage stability of CO_(2)-rich IWG.

A Comparative Investigation of the Biodegradation Behaviour of Linseed Oil-Based Cross-Linked Composites Filled with Industrial Waste Materials in Two Different Soils

The biodegradation of polymeric biocomposites formed from epoxidized linseed oil and various types of fillers(pine needles,pine bark,grain mill waste,rapeseed cake)and a control sample without filler was studied during 180 days of exposure to two types of forest soil:deciduous and coniferous.The weight loss,morphological,and structural changes of polymer composites were noticed after 180 days of the soil burial test.The greatest weight loss of all tested samples was observed in coniferous forest soil(41.8%–63.2%),while in deciduous forest soil,it ranged between 37.7%and 42.3%.The most significant changes in the intensities of the signals evaluated by attenuated total reflectance infrared spectroscopy,as well as morphological changes determined by scanning electron microscopy,were assessed for polymer composite with rapeseed cake and specimen without filler in coniferous forest soil and are in a good agreement with weight loss results.Whereas significantly lower changes in weight loss,morphology,and structure of polymeric film with pine bark were noticed in both soils.It was suggested that fungi of Trichoderma,Penicillium,Talaromyces and Clonostachys genera are the possible soil microorganisms that degrade linseed oil-based cross-linked polymer composites.Moreover,the novel polymer composites have the potential to be an environmentally friendly alternative to petroleum-based mulching films.

Industrial wastes applications for alkalinity regulation in bauxite residue: A comprehensive review

Bauxite residue is a highly alkaline material generated from the production of alumina in which bauxite is dissolved in caustic soda.Approximately 4.4 billion tons of bauxite residues are either stockpiled or landfilled,creating environmental risks either from the generation of dust or migration of filtrates.High alkalinity is the critical factor restricting complete utilization of bauxite residues,whilst the application of alkaline regulation agents is costly and difficult to apply widely.For now,current industrial wastes,such as waste acid,ammonia nitrogen wastewater,waste gypsum and biomass,have become major problems restricting the development of the social economy.Regulation of bauxite residues alkalinity by industrial waste was proposed to achieve‘waste control by waste’with good economic and ecological benefits.This review will focus on the origin and transformation of alkalinity in bauxite residues using typical industrial waste.It will propose key research directions with an emphasis on alkaline regulation by industrial waste,whilst also providing a scientific reference point for their potential use as amendments to enhance soil formation and establish vegetation on bauxite residue disposal areas(BRDAs)following large-scale disposal.

Effect of quarry dust addition on the performance of controlled low-strength material made from industrial waste incineration bottom ash

The performance of industrial waste incineration bottom ash in controlled low-strength material （CLSM） was investigated in this paper, as the quarry dust was added. CLSM mixtures were made from the industrial waste incineration bottom ash, quarry dust, and cement. Tests for fresh density, bleeding, compressive strength, shear strength, hydraulic conductivity, and excavatability were carried out. The com- pressive strength ranges from 60 kPa to 6790 kPa, the friction angle varies from 5°to 19°, and the cohesion is from 4 to 604 kPa. Most of the mixtures are found to be non-excavatable. It is indicated that the quarry dust addition increases the compressive strength and shear parame- ters, decreases bleeding, and increases the removability modulus.

Reaction Process of Chromium Slag Reduced by Industrial Waste in Solid Phase

M, a particular industrial waste, was selected to detoxify chromium slag at a high temperature. The carbon remaining in M reduced Cr （ Ⅳ ） of Na2 CrO4 borne in the chromium slag to Cr （ Ⅲ ） in the solid phase reaction, and its thermodynamics and kinetics were studied. The reduction process of Na2CrO4 by carbon produced CO, whiCh＇was endothermic. Under the experimental condition, the apparent activation energy was 4. 41 kJ·mol^-1 , the＇apparent order of reaction for Na2 CrO4 was equal to one, and the partial pressure of CO was only 0.22 Pa at 1 330℃.

Preparation of Super Composite Cement with a Lower Clinker Content and a Larger Amount of Industrial Wastes

The effects of the grinding mode,fineness,gypsum kinds and dosage,mix proportions on properties of the composite cements consisting of slag,fly ash,limestone and a lower content clinker were investigated,respectively.The results show that when the proportions among slag,fly ash and limestone are appropriate,the grinding technology and system are reasonable,the optimized gypsums and additives are effective,the 52.5R grade cement (52.5R grade cement means a higher strength than 52.5 at early age) can be prepared by clinker dosage of 50% in weight,the 42.5R or 42.5,32.5 grade composite cement containing 40% and 30% clinker also may be made, respectively.Moreover,the high performance concrete prepared from the above composite cements was studied experimentally.

Plant Test of Industrial Waste Disposal in a Cement Kiln

Destruction of industrial waste in cement rotary kilns (CRKs) is an alternative technology for the treatment of certain types of industrial waste (IW). In this paper, three typical types of industrial wastes were co-incinerated in the CRK at Beijing Cement Plant to determine the effects of waste disposal (especially solid waste disposal) on the quality of clinker and the concentration of pollutants in air emission. Experimental results show that (1) waste disposal does not affect the quality of clinker and fly ash, and fly ash after the IW disposal can still be used in the cement production, (2) heavy metals from IW are immobilized and stabilized in the clinker and cement, and (3) concentration of pollutants in air emission is far below than the permitted values in the China National Standard-Air Pollutants Emission Standard (GB 16297-1996).

Zeolite Synthesis under Insertion of Silica Rich Filtration Residues from Industrial Wastewater Reconditioning

Zeolite synthesis was studied using two silica rich filtration residues (FR 1 and FR 2) as Si-source and sodium aluminate in a direct synthesis at 60°C at strong alkaline conditions (8 M - 16 M NaOH). In addition to these one-pot syntheses, a two-step process was investigated. Here, an alkaline digestion of FR at 60°C was followed by gel precipitation with sodium aluminate and gel crystallization under usual conditions of 80°C - 90°C. The results show that the substitution of chemical reagent sodium silicate by a waste material like FR as Si-source is possible but requires fine tuning of the reaction conditions as zeolite crystallization is a process under kinetic control. The solubility behaviour and impurities of the inserted filtration residues strongly influenced the course of reaction. Thus zeolites like hydrosodalite or intermediate zeolite between cancrinite and sodalite, or zeolite NaA or Z-21 in cocrystallization with hydrosodalite could be observed in the one pot syntheses already in a short time interval between 1 - 4 h depending on the alkalinity. The two step process yield to zeolites NaA and NaX in very good quality. The reaction process of FR in both reaction methods was characterized by chemical analyses, X-ray powder diffraction, Fourier transform infrared spectroscopy as well as scanning electron microscopy. Surface area and water content of selected products were further characterized by the BET-method and by thermogravimetry. Summing up the results, we can show that zeolite formation from filtration residues is possible by several reaction procedures as model cases for a re-use of industrial waste materials. Beside the importance for environmental protection, the reactions are of interest for zeolite chemistry as the re-use of FR is possible under economically conditions of low energy consumption at 60°C and short reaction periods.

An overview on industrial waste management in China

The article is a summary of the industrial waste management in China during the recent years.An overall description of industrial waste was given from generation; treatment, disposal and emission and comprehensive utilization. In spite of the serious situation of industrial waste,China has realized it and made great progress in establishing corresponding legislation system, taking a series of administrative measures and developing effective treatment and disposal technologies.However, there still exist many problems , and it is of great urgency to take countermeasures in industrial waste management.

Application of Fe-Based Amorphous Alloy in Industrial Wastewater Treatment:A Review

Amorphous alloy(MGs)is a solid alloy with disordered atomic accumulation obtained by ultra-rapid solidification of alloy melt.The atom deviates from the equilibrium position and is in metastable state.Up to now,a large number of MGs have been applied to the treatment of dye and heavy metal contaminated wastewater and ideal experimental results have been obtained.However,there is no literature to systematically summarize the chemical reaction and degradation mechanism in the process of degradation.On the basis of reviewing the classification,application,and synthesis of MGs,this paper introduces in detail the chemical reactions such as decolorization,mineralization,and ion leaching of Fe-based amorphous alloy(Fe-MGs)in the degradation of organic and inorganic salt wastewater through direct reduction or advanced oxidation mechanism.Compared with crystalline materials,the higher reaction rate of Fe-MGs can be attributed to lower activation energy,negative redox potential,loose product layer,and band structure with downward shift of valence band top.Finally,some suggestions and prospects are put forward for the limitations and research prospects of MGs in the environmental field,which provides a new idea for the synthesis of new environmental functional materials.

Long-Term Effect of Industrial Waste Water Irrigation on Soil Chemical Properties

A laboratory experiment was conducted in Soil Science Division of BRRI during 2011 aimed to determine the vertical distribution of soil chemical properties under long-term industrial waste water irrigated rice field. Waste water irrigated rice field seemed to create some differences in soil pH profile. The pHW and pHKCl in all soil depth was higher with waste water irrigated rice field. The surface charge of both the soils was considerably negative. Waste water irrigated rice field developed more negative charges in soils. Irrigation with waste water increased Electrical Conductivity （EC） in rice soils profile. The organic carbon content （%） started to decrease sharply with the increase in soil depth. Organic carbon content was higher with waste water irrigated rice soils Total nitrogen （%） was high with underground water irrigated rice soils in surface but at deeper, total N was similar in both soils. Olsen P （mg/kg） was higher with underground water irrigated soil at 0-5 cm depth but at 5-100 cm soils profile, it was higher with waste water irrigated rice soils. Micronutrients （Zn, Fe, Cu and Mn） and heavy metals （Pb, Cd, Ni and Cr） in soils were increased significantly through irrigation with waste water in rice-rice cropping pattern.

Polluter Pays Principle： Who Pays for Industrial Waste in Ho Chi Minh City, Vietnam

Rapid industrialization in Vietnam has resulted in the difficult task of finding means to properly manage the generation of industrial waste. In an attempt to deal with this problem, the Vietnamese government revised the Law on Environmental Protection of 2005, with which it imposed strict regulations on industrial waste generators and the waste they discharge. However, questions remain about the current industrial solid waste management system because of the discrepancy between the ideals embodied in the Law and the actual practices occurring in industry. We report here on the effectiveness of governmental policies, focusing on environmental performance in industrial zones in Ho Chi Minh City （HCMC）, Vietnam. We examined government records, and reports from waste generators, as well as waste treatment methods at sites. In addition, on-site surveys were carried out at 44 companies in HCMC in 2009 and 2010 to obtain a better understanding of the companies＇ handling of and attitude toward the industrial waste they produced. Our results show that the incoherence of the revised Law and regulations in industrial waste management has caused a serious pressure on domestic landfills. We conclude that there is a strong need for change in the current regulatory and management system in order to increase the effectiveness of environmental management for future sustainable development.

Development of Lightweight Concrete Using Industrial Waste Palm Oil Clinker

Concrete is a major material used in the construction of buildings and structures in the world.Gravel and sand are the major ingredients of concrete but are non-renewable natural materials.Therefore,the utilisation of palm oil clinker(POC),a solid waste generated from palm oil industry is proposed to replace natural aggregate in this research to reduce the demand for natural aggregates.One mix of ordinary concrete as control concrete;while four mix proportions of oil palm clinker concrete were obtained by replacing 25%,50%,75%,and 100%of gravel and sand of control concrete with coarse and fine oil palm clinker respectively by volume,with same cement content and water cement ratio.Compressive strength test was carried out of concretes with different percentages of oil palm clinker;whereas water absorption tests according to respective standard,were carried out to determine the durability properties of various mixes.Based on the results obtained,the study on the effect of percentage of clinker on strength and durability properties was drawn.According to ACI classification of light weight concrete only the 100 percentage replacement can achieve the definition of light weight concrete since its density is less than 1,900 kg/m3 and strength larger than 17 MPa.Eventually the 25%replacement of the normal aggregate by the OPC will improve the strength and durability of the concrete.

Semi-flowable self-consolidating concrete using industrial wastes for construction of rigid pavements in India:An overview

The construction of rigid pavements using conventionally vibrated concrete consumes a significant amount of energy as it requires rigorous vibrations.This also requires a high number of laborers and creates noise during construction.Thus,a new kind of concrete called semi-flowable self-consolidating concrete(SFSCC)for pavement construction using slip-form paving technology is reviewed in this article.The SFSCC requires no energy for compaction as it gets compacted under its self weight.It also renders shape stability in the fresh state which is critical to expedite the construction in slip form concreting.The review focuses on the need,evolution,and requirement of the ingredient materials,mix design,and methods for testing the properties of SFSCC.Further,the utilization of industrial wastes in the construction industry and the production of self-consolidating concrete are discussed.The literature on the effect of different materials on the properties of such concrete and field studies in this context are discussed.Lastly,its suitability as pavement construction material either in normal rural roads or in low-volume village roads is discussed in the Indian context.The review reveals that relatively less amount of study on SFSCC in general and as a pavement material in particular is available in the literature and pursuant to this,creates a wide scope of research.

Toxicological and Life-Cycle Perspectives on Waste-Derived Nanoparticles

Many nanoparticles have been created over the last few decades using a variety of techniques and used to develop environmental technology, including water treatment, the detection of persistent contaminants, and soil and water remediation. The studies of alternative inputs for nanoparticle production as well as the use of green synthesis techniques are driven by the field of materials science and engineering’s growing interest in increasing the sustainability of the processes involved in their production. In this paper, we begin by providing an overview of the fundamental principles of producing nanoparticles from different sources, such as plastic, electronic, metal, and industrial waste. We elaborate on key facts of waste identification as a workable input for the treatment and recovery of metal and carbon-based nanoparticles. We next go over several controlling factors that play a role in creating nanoparticles, pointing out probable conclusions as we go. Then, we show some instances of waste-derived nanoparticles used in a proof-of-concept experiment of technology for applications in water quality and safety. Before scaling up production and implementing waste-derived nanoparticles, there are several present problems from the toxicological and life-cycle perspectives that must be taken into account.

Bird’s-eye view of recycled solid wastes in road engineering

Recent trends in road engineering have explored the potential of incorporating recycled solid wastes into infrastructures that including pavements,bridges,tunnels,and accessory structures.The utilization of solid wastes is expected to offer sustainable solutions to waste recycling while enhancing the performance of roads.This review provides an extensive analysis of the recycling of three main types of solid wastes for road engineering purposes:industrial solid waste,infrastructure solid waste,and municipal life solid waste.Industrial solid wastes suitable for road engineering generally include coal gangue,fly ash,blast furnace slag,silica fume,and steel slag,etc.Infrastructure solid wastes recycled in road engineering primarily consist of construction&demolition waste,reclaimed asphalt pavements,and recycled cement concrete.Furthermore,recent exploration has extended to the utilization of municipal life solid wastes,such as incinerated bottom ash,glass waste,electronics waste,plastic waste,and rubber waste in road engineering applications.These recycled solid wastes are categorized into solid waste aggregates,solid waste cements,and solid waste fillers,each playing distinct roles in road infrastructure.Roles of solid waste acting aggregates,cements,and fillers in road infrastructures were fully investigated,including their pozzolanic properties,integration effects to virgin materials,modification or enhancement solutions,engineering performances.Utilization of these materials not only addresses the challenge of waste management but also offers environmental benefits aiming carbon neutral and contributes to sustainable infrastructure development.However,challenges such as variability in material properties,environmental impact mitigation,secondary pollution to environment by leaching,and concerns regarding long-term performance need to be further addressed.Despite these challenges,the recycled solid wastes hold immense potential in revolutionizing road construction practices and fostering environmental stewardship.This review delves into a bird’seye view of the utilization of recycled solid wastes in road engineering,highlighting advances,benefits,challenges,and future prospects.

Potential use of magnesium industrial waste for synthesis of Li and Mg co-doped LiMn_(2)O_(4)nanoparticles as cathode material for Li-ion batteries:Effect of sintering temperature

Potential advantages of active electrode nanomaterials have led to development of high energy and power density lithium-ion(Li-ion)batteries.However,under increasing demand for critical resources such as lithium and cobalt,it is necessary to use abundant raw materials,which can be obtained from industrial waste.In this work,purified Mg(OH)_(2)from waste generated in the production of Li2CO3 with natural brines from the Salar de Atacama(Chile)is used as a doping agent for synthesis of LiMn_(2)O_(4)(LMO)spinel octahedral nanoparticles co-doped with excess Li and Mg.Crystallization of a pure cubic spinel phase(Fd3m)takes place at 500℃and sintering temperature effect at 580 and 750℃,thus the elemental composition and the structural,morphological,and electrochemical properties are studied in detail.Optimum electrochemical performance at room temperature is obtained for Li_(1.03)Mg_(0.05)Mn_(1.92)O_(4)spinel sintered at 750℃with an initial discharge capacity of 121.3 mAh·g^(-1)and capacity retention of 94.0%after 100 cycles at C/3.A locally ordered spinel structure is obtained at 750℃,and doping with Mg^(2+)improves structural rigidity.Synergy between both effects resulted in a high Li^(+)diffusion rate(1.29×10^(-9)cm^(2)·s^(-1))significantly improving cycling performance at elevated C-rates in 50℃.

Research Progress on Porous Ceramics Prepared from Industrial Solid Wastes

The situation of porous ceramics prepared from industrial waste slag(fly ash,red mud,metallurgical slag,tailings,etc.)was summarized.It was pointed out that the preparation of porous ceramics from industrial waste slag can bring long-term economic and social benefits.The development trend of secondary utilization of industrial waste slag was also prospected.

Numerical study of a hybrid absorption-compression high temperature heat pump for industrial waste heat recovery

The present paper aims at exploring a hybrid absorption-compression heat pump （HAC-HP） to upgrade and recover the industrial waste heat in the temperature range of 60℃-120℃. The new HAC-HP system proposed has a condenser, an evaporator, and one more solution pump, compared to the conventional HAC-HP system, to allow flexible utilization of energy sources of electricity and waste heat. In the system proposed, the pressure of ammonia-water vapor desorbed in the generator can be elevated by two routes; one is via the compression of compressor while the other is via the condenser, the solution pump, and the evaporator. The results show that more ammonia-water vapor flowing through the compres- sor leads to a substantial higher energy efficiency due to the higher quality of electricity, however, only a slight change on the system exergy efficiency is noticed. The temperature lift increases with the increasing system recirculation flow ratio, however, the system energy and exergy efficiencies drop towards zero. The suitable operation ranges of HAC-HP are recommended for the waste heat at 60℃, 80℃, 100℃, and 120℃. The recirculation flow ratio should be lower than 9, 6, 5, and 4 respectively for these waste heat, while the temperature lifts are in the range of 9.8℃-27.7 ℃, 14.9℃~4.1 ℃, 24.4℃-64.1 ℃, and 40.7℃-85.7℃, respectively, and the system energy efficiency are 0.35-0.93, 0.32-0.90, 0.25- 0.85, and 0.14-0.76.

A novel method of water remediation of organic pollutants and industrial wastes by solution- route processed CZTS nanocrystals

CZTS(Cu_(2)ZnSnS_(4)),a P-type semiconductor with a direct bandgap(1.2-1.7eV),earth-abundant,non-toxic,and has a large absorption coefficient makes it extremely useful in optoelectronics and light-harvesting applications.In this work,CZTS is prepared by an ingenious,cost-effective colloidal route using the‘hotinjection’method with the usage of different ligands.The XRD and Raman spectroscopy shows the single-phase highly crystalline CZTS nanoparticles with kesterite structure.The TEM results show that the size of CZTS nanoparticles is about 2-5 nm and monodispersity is confirmed by DLS(Dynamic Light Scattering).FTIR confirms the presence of different ligands used in CZTS preparation.The Uv-vis absorption shows the direct bandgap of 1.5-1.7eV.The contact angle study shows the hydrophobic nature of as-synthesized CZTS nanoparticles which were further ligand exchanged with L-cysteine hydrochloride to make it hydrophilic to study the photocatalytic degradation activity of organic pollutants and industrial waste in the water.The photocatalysis experiments were performed under two conditions:(i)under bare sunlight(Intensity~900 W/m^(2))(ii)focussing the sample under the sunlight via converging lens(1800 W/m^(2)).The photocatalytic efficiencies were then compared and the best photocatalytic efficiency achieved under sunlight was 98.4%for organic pollutants and 75%for industrial waste via converging lens while the corresponding efficiencies with bare sunlight were 98.1% and 73% respectively.To the best of the author’s knowledge,a rapid and highly efficient photocatalysis of CZTS NPs employing a converging lens for water-remediation without the usage of noble&transition-metals has been reported for the first time.