Development and prospect on fully mechanized mining in Chinese coal mines

Fully mechanized mining(FMM)technology has been applied in Chinese coal mines for more than 40 years.At present,the output of a FMM face has reached 10-million tons with Chinese-made equipment.In this study,the new developments in FMM technology and equipment in Chinese coal mines during past decades are introduced.The automatic FMM technology for thin seams,complete sets of FMM technology with ultra large shear height of 7 m for thick seams,complete sets of fully mechanized top coal caving technology with large shear height for ultra-thick seams of 20 m,complete sets of FMM technology for complex and difficult seams,including steeply inclined seams,soft coal seams with large inclination angle,and the mechanized filling mining technology and equipment are presented.Some typical case studies are also introduced.Finally,the existing problems with the FMM technology are discussed,and prospect of FMM technology and equipment applied in Chinese coal mines is put forward.

Field application of non-blasting mechanized mining using high-frequency impact hammer in deep hard rock mine

A non-blasting mechanized mining experiment was carried out with a high-frequency impact hammer,and the daily mining performance was recorded to explore the applicability of the high-frequency impact hammer in deep hard rock mines.Before the field application,the scope of the excavation damage zone was monitored,and rock samples were obtained from the ore body to be mined to carry out a series of laboratory experiments.Field application results show that the overall excavation efficiency reaches 50.6 t/h,and the efficiency of pillar excavation after excavating stress relief slot reaches 158.2 t/h.The results indicate that the non-blasting mechanized mining using high-frequency impact hammer has a good application in deep hard rock mines,and the stress relief slot is conducive to mechanical excavation.In addition,the high-frequency impact hammer also exhibits the advantages of high utilization rate of labor hours,small lumpiness of spalling ore,little dust,and little excavation damage.Finally,according to the field application and laboratory experiment results,a non-blasting mechanized mining method for hard rock mines based on high-frequency impact hammer is proposed.

Effect of suppressing dust by multi-direction whirling air curtain on fully mechanized mining face

A combined method of numerical simulation and field testing was adopted in this study in the interest of solving the problem of hard to control high concentrate dusts on a fully mechanized mining face. In addi- tion, the dust suppression effect of a multi-direction whirling air curtain was studied in this paper. Under the influence of the wall attachment effect, the compressed air which blows out from the two-phase or three-phase radial outlets on the generator of the air curtain can form a multi-direction whirling air curtain, which can cover the whole roadway section of a fully mechanized mining face. The traditional method of controlling dust is a forcing system with exhaust overlap which has the major disadvantage of lacking a jet effect and consequently results in poor dust control. It is difficult to form the air flow field within the range of Lp ≤ 5√S. However, due to the effect of this novel system, the radial airflow can be turned into axial airflow allowing fresh air to flow through the length of the heading. The air flow field which is good at controlling dust diffusion can be formed 12.8 m from the heading face. Furthermore, the field measurement results show that before the application of a multi-direction whirling air curtain, the dust concentration is 348.6 mg/m^3 and 271.4 mg/m^3 respectively at the roadway cross-section measurement points which are 5 m and 10 m from the heading face. However, after the application of the multi-direction whirling air curtain, the dust concentration is only 61.2 mg/m3 and 14.8 mg/m^3, respectively. Therefore, the dust control effect of a multi-direction whirling air curtain is obvious.

Mining pressure monitoring and analysis in fully mechanized backfilling coal mining face-A case study in Zhai Zhen Coal Mine

Fully mechanized solid backfill mining(FMSBM) technology adopts dense backfill body to support the roof. Based on the distinguishing characteristics and mine pressure control principle in this technology, the basic principles and methods for mining pressure monitoring were analyzed and established. And the characteristics of overburden strata movement were analyzed by monitoring the support resistance of hydraulic support, the dynamic subsidence of immediate roof, the stress of backfill body, the front abutment pressure, and the mass ratio of cut coal to backfilled materials. On-site strata behavior measurements of 7403 W solid backfilling working face in Zhai Zhen Coal Mine show that the backfill body can effectively support the overburden load, obviously control the overburden strata movement, and weaken the strata behaviors distinctly. Specific performances are as follows. The support resistance decreases obviously; the dynamic subsidence of immediate roof keeps consistent to the variation of backfill body stress, and tends to be stable after the face retreating to 120-150 m away from the cut. The peak value of front abutment pressure arises at 5-12 m before the operating face, and mass ratio is greater than the designed value of 1.15, which effectively ensures the control of strata movement. The research results are bases for intensively studying basic theories of solid backfill mining strata behaviors and its control, and provide theoretical guidance for engineering design in FMSBM.

Similar material simulation research on movement law of roof over-lying strata in stope of fully mechanized caving face with large mining height

Similar material simulation test W9-15 101 fully mechanized caving face with was carried out in a geological model of large mining height in the Liuhuanggou Colliery, in Xinjiang Uigur Autonomous Region. The roof overlying strata movement law in the stope of a fully mechanized caving face with large mining height was studied and show that the roof overlying strata in the stope of a fully mechanized caving face with large mining height can be formed into a stable arch structure; the fracture rock beam is formed resembling a ＂bond beam＂, but it has essentially the structure of ＂multi-span beams＂ under the big structure of the stable arch. The roof overlying strata movement law in the stope of a fully mechanized caving face with large mining height is similar to that of the common, fully mechanized caving stope, which is determined by the deformation and instability of the structure of ＂multi-span beams＂. But because of the differences between the mining heights, the peak pressure in the stope of a fully mechanized caving face with large mining height is smaller while the affected area of abutment pressure is wider in the front of the working face; this is the obvious difference in abutment pressure between the stope of a fully mechanized caving face with large mining height and that of the common.

Study on dangers of methane in the gob of fully mechanized caving mining

Divided the gob gas in different types according to falling structure and spatial patterns of gob of the fully mechanized caving mining and analyzed its main form of harm. This passage preliminarily studied the law of unusual gush of gob gas of the fully mechanized caving mining. According to the basic condition for the gas explosion, made comprehensive analysis and appraisal about the oxygen condition, gas concentration distribute and fire source conditions. And find that there is the dangerous district of gas explosion in a certain area of the producing gob and give the three zone theory of gob gas explosion.

STUDY ON PRODUCTION SYSTEM OPERATION REGULARITY OF FULLY MECHANIZED SUBLEVEL CAVING MINING AND SEQUENTIAL OPERATION

According to a lot of practical data in Liujialiang Mine and reliability theory and result of computer simulation, operation regularity of fully mechanized sublevel caving mining production system in the condition of gently inclined complicated geological structure and production shortcomings are found out and reliability of system and output of the working face are predicted finally.

Field test of high-power microwave-assisted mechanical excavation for deep hard iron ore

Microwave-assisted mechanical excavation has great application prospects in mines and tunnels,but there are few field experiments on microwave-assisted rock breaking.This paper takes the Sishanling iron mine as the research object and adopts the self-developed high-power microwave-induced fracturing test system for hard rock to conduct field experiments of microwave-induced fracturing of iron ore.The heating and reflection evolution characteristics of ore under different microwave parameters(antenna type,power,and working distance)were studied,and the optimal microwave parameters were obtained.Subsequently,the ore was irradiated with the optimal microwave parameters,and the cracking effect of the ore under the action of the high-power open microwave was analyzed.The results show that the reflection coefficient(standing wave ratio)can be rapidly(<5 s)and automatically adjusted below the preset threshold value(1.6)as microwave irradiation is performed.When using a right-angle horn antenna with a working distance of 5 cm,the effect of automatic reflection adjustment reaches the best among other antenna types and working distances.When the working distance is the same,the average temperature of the irradiation surface and the area of the high-temperature area under the action of the two antennas(right-angled and equal-angled horn antenna)are basically the same and decrease with the increase of working distance.The optimal microwave parameters are:a right-angle horn antenna with a working distance of 5 cm.Subsequently,in further experiments,the optimal parameters were used to irradiate for 20 s and 40 s at a microwave power of 60 kW,respectively.The surface damage extended 38 cm×30 cm and 53 cm×30 cm,respectively,and the damage extended to a depth of about 50 cm.The drilling speed was increased by 56.2%and 66.5%,respectively,compared to the case when microwaves were not used.

Application of deep borehole blasting on fully mechanized hard top-coal pre-splitting and gas extraction in the special thick seam

In order to solve the problems of top-coal inadequate destruction and large amounts of gas emission in mining extra thick and hard coal seam,this study investigated the pre-splitting for deep borehole blasting and gas pre-draining technologies on top coal.The mechanism of the technologies was systematically expounded based on hard top-coal cracks development obtained by numerical simulation and theoretical analysis.The results show that explosive blasting in the hard rock results in a large number of cracks and large displacement in the rock mass due to the effect of explosion stress.Meanwhile,the thick top-coal caves,and desorbing gas flows along the cracks improve gas extraction.Finally,the pre-splitting for deep borehole blasting and gas pre-draining technologies was applied in No.3802 working face of Shui Liandong Coal Mine,which increases monthly output in the face to 67.34 kt and the drained gas concentration to 86.2%.The drained gas average concentration from each borehole reaches 40%,and the effect is remarkable.

The Recent Technological Development of Intelligent Mining in China

In the last five years, China has seen the technological development of intelligent mining and the application of the longwall automation technology developed by the Longwall Automation Steering Committee. This paper summarizes this great achievement, which occurred during the 12th Five-Year Plan （2011-2015）, and which included the development of a set of intelligent equipment for hydraulic-powered supports, information transfers, dynamic decision-making, performance coordination, and the achievement of a high level of reliability despite difficult conditions. Within China, the intelligent system of a set of hydraulic-powered supports was completed, with our own intellectual property rights. An intelligent mining model was developed that permitted unmanned operation and single-person inspection on the work face. With these technologies, the number of miners on the work face can now be significantly reduced. Miners are only required to monitor mining machines on the roadway or at the surface control center, since intelligent mining can be applied to extract middle-thick or thick coal seams. As a result, miners＇ safety has been improved. Finally, this Darter discusses theprospects and challenges of intelligent mining over the next ten years.

CHINA'S RECENT DEVELOPMENT IN COAL MINING,PROCESSING AND UTILIZATION

This paper describes the state-of-the-art and Outlook of coal mining and clean coal technology in China. As the major mining method,underground mining accounts for 96% of the total production. Among the state own mines, the percentage of mechanized mining reached 71 %. A rapid development of high-productive and high-profitable mines,especially those with longwall sublevel caving method, is described. The issues of heavy duty equipment, roof bolting,mine safety are also addressed. The Chinese government is paying more and more attention on the environmental problems inducing from coal mining,processing and utilization. A basic framework of clean coal technology is being formed and a wide range of technology is included.

Innovation and future of mining rock mechanics

The 121 mining method of longwall mining first proposed in England has been widely used around the world.This method requires excavation of two mining roadways and reservation of one coal pillar to mine one working face.Due to considerable excavation of roadway,the mining roadway is generally destroyed during coal mining.The stress concentration in the coal pillar can cause large deformation of surrounding rocks,rockbursts and other disasters,and subsequently a large volume of coal pillar resources will be wasted.To improve the coal recovery rate and reduce excavation of the mining roadway,the 111 mining method of longwall mining was proposed in the former Soviet Union based on the 121 mining method.The 111 mining method requires excavation of one mining roadway and setting one filling body to replace the coal pillar while maintaining another mining roadway to mine one working face.However,because the stress transfer structure of roadway and working face roof has not changed,the problem of stress concentration in the surrounding rocks of roadway has not been well solved.To solve the above problems,the conventional concept utilizing high-strength support to resist the mining pressure for the 121 and 111 mining methods should be updated.The idea is to utilize mining pressure and expansion characteristics of the collapsed rock mass in the goaf to automatically form roadways,avoiding roadway excavation and waste of coal pillar.Based on the basic principles of mining rock mechanics,the“equilibrium mining”theory and the“short cantilever beam”mechanical model are proposed.Key technologies,such as roof directional presplitting technology,negative Poisson’s ratio(NPR)high-prestress constant-resistance support technology,and gangue blocking support technology,are developed following the“equilibrium mining”theory.Accordingly,the 110 and N00 mining methods of an automatically formed roadway(AFR)by roof cutting and pressure releasing without pillars are proposed.The mining methods have been applied to a large number of coal mines with different overburdens,coal seam thicknesses,roof types and gases in China,realizing the integrated mode of coal mining and roadway retaining.On this basis,in view of the complex geological conditions and intelligent mining demand of coal mines,an intelligent and unmanned development direction of the“equilibrium mining”method is prospected.

Fracture mechanics model of fully mechanized top coal caving of shallow coal seams and its application

Based on break characteristics of roofs in fully mechanized top-coal mining of thick shallow coal seams, a fracture mechanics model was built, and the criterion of crack propagation in the main roof was derived using the fracture mechanics theory. The relationships between the fracture length of the roof and the working resistance of the supports were discovered, and the correlations between the load on the overlying strata and the ratio of the crack's length to the thickness of the roof were obtained. Using a working face of Jindi Coal Mine, Xing county Shanxi province as an example, the relationships between the fracture length of the roof and the working resistance of the supports were analysed in detail. The results give a design basis in hydraulic top coal caving supports, which could provide useful references in the practical application. On-site experiment proves that the periodic weighting step interval of the caving face is 15–16 m, which is basically consistent with the theoretical analysis results, and indicates that the mechanized caving hydraulic support is capable of meeting the support requirements in the mining of a super-thick but shallowly buried coal seam.

Opportunities and Challenges in Deep Mining： A Brief Review

Mineral consumption is increasing rapidly as more consumers enter the market for minerals and as the global standard of living increases. As a result, underground mining continues to progress to deeper levels in order to tackle the mineral supply crisis in the 21 st century. However, deep mining occurs in a very technical and challenging environment, in which significant innovative solutions and best practice are required and additional safety standards must be implemented in order to overcome the challenges and reap huge eco- nomic gains. These challenges include the catastrophic events that are often met in deep mining engineering： rockbursts, gas outbursts, high in situ and redistributed stresses, large deformation, squeezing and creeping rocks, and high temperature. This review paper presents the current global status of deep mining and high-lights some of the newest technological achievements and opportunities associated with rock mechanics and geotechnical engineering in deep mining. Of the various technical achievements, unmanned workingfaces and unmanned mines based on fully automated mining and mineral extraction processes have become important fields in the 21 st century.

Vertical transportation system of solid material for backfilling coal mining technology

For transportation of solid backfill material such as waste and fly ash from the surface to the bottom of the shaft in a fully mechanized backfilling coal backfilling coal mining technology, we developed a new vertical transportation system to transport this type of solid backfill material. Given the demands imposed on safely in feeding this material, we also investigated the structure and basic parameter of this system. For a mine in the Xingtai mining area the results show that: (1) a vertical transportation system should include three main parts, i.e., a feeding borehole, a maintenance chamber and a storage silo; (2) we determined that 486 mm is a suitable diameter for bore holes, the diameter of the storage silo is 6 m and its height 30 m in this vertical transportation system; (3) a conical buffer was developed to absorb the impact during the feeding process. To ensure normal implementation of fully mechanized backfilling coal mining technology and the safety of underground personnel, we propose a series of security technologies for anti-blockage, storage silo cleaning, high pressure air release and aspiration. This vertical transporting system has been applied in one this particular mine, which has fed about 4 million tons solid material with a feeding depth of 350 m and safely exploited 3 million tons of coal.

Ground pressure and overlying strata structure for a repeated mining face of residual coal after room and pillar mining

To investigate the abnormal ground pressures and roof control problem in fully mechanized repeated mining of residual coal after room and pillar mining, the roof fracture structural model and mechanical model were developed using numerical simulation and theoretical analysis. The roof fracture characteristics of a repeated mining face were revealed and the ground pressure law and roof supporting condi- tions of the repeated mining face were obtained. The results indicate that when the repeated mining face passes the residual pillars, the sudden instability causes fracturing in the main roof above the old goal and forms an extra-large rock block above the mining face. A relatively stable ＂Voussoir beam＂ structure is formed after the advance fracturing of the main roof. When the repeated mining face passes the old goaf, as the large rock block revolves and touches gangue, the rock block will break secondarily under overburden rock loads. An example calculation was performed involving an integrated mine in Shanxi province, results showed that minimum working resistance values of support determined to be reason- able were respectively 11,412 kN and 10,743 kN when repeated mining face passed through residual pillar and goaf. On-site ground pressure monitoring results indicated that the mechanical model and support resistance calculation were reasonable.

Some Challenges of Deep Mining

An increased global supply of minerals is essential to meet the needs and expectations of a rapidly rising world population. This implies extraction from greater depths. Autonomous mining systems, developed through sustained R＆D by equipment suppliers, reduce miner exposure to hostile work environments and increase safety. This places increased focus on ＂ground control＂ and on rock mechanics to define the depth to which minerals may be extracted economically. Although significant efforts have been made since the end of World War II to apply mechanics to mine design, there have been both technological and organizational obstacles. Rock in situ is a more complex engineering material than is typically encountered in most other engineering disciplines. Mining engineering has relied heavily on empirical procedures in design for thousands of years. These are no longer adequate to address the challenges of the 21st century, as mines venture to increasingly greater depths. The development of the synthetic rock mass （SRM） in 2008 provides researchers with the ability to analyze the deformational behavior of rock masses that are anisotropic and discontinuous-attributes that were described as the defining characteristics of in situ rock by Leopold Mfiller, the president and founder of the International Society for Rock Mechanics （ISRM）, in 1966. Recent developments in the numerical modeling of large-scale mining operations （e.g., caving） using the SRM reveal unanticipated deformational behavior of the rock. The application of massive parallelization and cloud computational techniques offers major opportunities： for example, to assess uncertainties in numerical predictions： to establish the mechanics basis for the empirical rules now used in rock engineering and their validity for the prediction of rock mass behavior beyond current experience： and to use the discrete element method （DEM） in the optimization of deep mine design. For the first time, mining-and rock engineering-will have its own mechanics-based Ulaboratory.＂ This promises to be a major tool in future planning for effective mining at depth. The paper concludes with a discussion of an opportunity to demonstrate the application of DEM and SRM procedures as a laboratory, by back-analysis of mining methods used over the 80-year history of the Mount Lvell Copper Mine in Tasmania.

Rock roadway complementary support technology in Fengfeng mining district

This paper takes No.52 return uphill roadway of Yangquhe coal mine as a research project. Based on the research, especially its geological condition, indoor experiments, numerical simulation and theoretical analysis were employed to determine the difficult coefficients of Yangquhe project. By using these means,the difficult coefficients of the deep rock engineering were determined. From a study of the effects of crustal stress and the roof mechanism on roadway stability, the transformation mechanism in Yangquhe coal mine has been determined. As a result of this research, the interactive support technology of prestressed cable mesh was developed and the technology tested in mining engineering, which proved to be feasible.

Analysis of drug use law and mechanism of prostate cancer based on data mining and network pharmacology

Objective: Excavate the medication rule of traditional Chinese medicine in the treatment of prostate cancer, and predicting the biomolecular level mechanism of high-frequency drug compatibility. Methods: Relevant documents in CNKI, Wanfang Medical Network and VIP Chinese Biomedical Periodical Database Pubmed, EMbase were collected and collated systematically. Frequency statistics, association rule analysis and new party mining were carried out using TCMISSV2.5. BATMAN-TCM was used to analyze the interaction relationship and related pathways between high-frequency drug targets. Results: Huangqi (Astragalus membranaceus) was the single drug most used of the 102prescriptions included in the standard. There are 6 pairs of combinations with high confidence in association rule analysis. System entropy cluster analysis resulted in 20 core drug combinations and 9 new prescriptions. Through KEGG pathway analysis of Huangqi, Fuling (Poria cocos), Gancao (Glycyrrhiza uralensis) and Dihuang (Rehmannia glutinosa), it was found that the number of potential targets of the neural active ligand receptor rented pathway and purine metabolism pathway was the largest. Conclusions: Prostate cancer is mainly treated with deficiency-tonifying drugs, which are combined with drugs for promoting blood circulation, removing blood stasis, clearing heat, promoting diuresis, detoxifying and resolving hard mass. The mechanism of action of high-frequency traditional Chinese medicine may be realized by interfering with the neuroactive ligand receptor interaction pathway and purine metabolism pathway.

The research of the evaluation system for the sealability of hydraulic supports and jacks＇ seals

In order to enhance the sealing quality and assemble efficiency of hydraulic supports, the evaluation system for the sealability of the hydraulic support and jack＇s seals was established through the testing and experimenting technology in respects, such as seals＇ dimensions, reasonable amounts of compression, sealability, life, resistance to pressure, etc. Through life detecting test of the seal, found the longest life seal ring under the same conditions, and through the reciprocating test of the hydraulic support, found the most appropriate amount of interference between the groove and the seal ring, thus, to decrease the leakage and extend the life span of the hydraulic support.