The Impact of Model Based Offset Scaling Technique on the Amplitude Variation with Offset Responses from 3D Seismic Data Acquired from the Tano Basin, Offshore Ghana

Amplitudes have been found to be a function of incident angle and offset. Hence data required to test for amplitude variation with angle or offset needs to have its amplitudes for all offsets preserved and not stacked. Amplitude Variation with Offset (AVO)/Amplitude Variation with Angle (AVA) is necessary to account for information in the offset/angle parameter (mode converted S-wave and P-wave velocities). Since amplitudes are a function of the converted S- and P-waves, it is important to investigate the dependence of amplitudes on the elastic (P- and S-waves) parameters from the seismic data. By modelling these effects for different reservoir fluids via fluid substitution, various AVO geobody classes present along the well and in the entire seismic cube can be observed. AVO analysis was performed on one test well (Well_1) and 3D pre-stack angle gathers from the Tano Basin. The analysis involves creating a synthetic model to infer the effect of offset scaling techniques on amplitude responses in the Tano basin as compared to the effect of unscaled seismic data. The spectral balance process was performed to match the amplitude spectra of all angle stacks to that of the mid (26°) stack on the test lines. The process had an effect primarily on the far (34° - 40°) stacks. The frequency content of these stacks slightly increased to match that of the near and mid stacks. In offset scaling process, the root mean square (RMS) amplitude comparison between the synthetic and seismic suggests that the amplitude of the far traces should be reduced relative to the nears by up to 16%. However, the exact scaler values depend on the time window considered. This suggests that the amplitude scaling with offset delivered from seismic processing is only approximately correct and needs to be checked with well synthetics and adjusted accordingly prior to use for AVO studies. The AVO attribute volumes generated were better at resolving anomalies on spectrally balanced and offset scaled data than data delivered from conventional processing. A typical class II AVO anomaly is seen along the test well from the cross-plot analysis and AVO attribute cube which indicates an oil filled reservoir.

Model based SOC estimation for high-power Li-ion battery packs used on FCHVs

A model based method which recruited the extended Kalman filter （EKF） to estimate the full state of charge （SOC） of Li-ion battery was proposed. The underlying dynamic behavior of the cell pack was described based on an equivalent circuit comprising of two capacitors and three resistors. Measurements in two tests were applied to compare the SOC estimated by model based EKF estimation with the SOC calculated by coulomb counting. Results have shown that the proposed method is able to perform a good estimation of the SOC of battery packs. Moreover, a corresponding battery management systems （BMS） including software and hardware based on this method was designed.

Auxiliary Model Based Multi-innovation Stochastic Gradient Identification Methods for Hammerstein Output-Error System

Special input signals identification method based on the auxiliary model based multi-innovation stochastic gradient algorithm for Hammerstein output-error system was proposed.The special input signals were used to realize the identification and separation of the Hammerstein model.As a result,the identification of the dynamic linear part can be separated from the static nonlinear elements without any redundant adjustable parameters.The auxiliary model based multi-innovation stochastic gradient algorithm was applied to identifying the serial link parameters of the Hammerstein model.The auxiliary model based multi-innovation stochastic gradient algorithm can avoid the influence of noise and improve the identification accuracy by changing the innovation length.The simulation results show the efficiency of the proposed method.

3DV quality model based depth maps for view synthesis in FTV system

Depth maps are used for synthesis virtual view in free-viewpoint television （FTV） systems. When depth maps are derived using existing depth estimation methods, the depth distortions will cause undesirable artifacts in the synthesized views. To solve this problem, a 3D video quality model base depth maps （D-3DV） for virtual view synthesis and depth map coding in the FTV applications is proposed. First, the relationships between distortions in coded depth map and rendered view are derived. Then, a precisely 3DV quality model based depth characteristics is develop for the synthesized virtual views. Finally, based on D-3DV model, a multilateral filtering is applied as a pre-processed filter to reduce rendering artifacts. The experimental results evaluated by objective and subjective methods indicate that the proposed D-3DV model can reduce bit-rate of depth coding and achieve better rendering quality.

A Photonuclear Reaction Model Based on IQMD in Intermediate-Energy Region

A photonuclear reaction transport model based on an isospin-dependent quantum molecular dynamics model （IQMD） is presented in the intermediate energy region, which is named as GiQMD in this study. Methodology to simulate the course of the photonuclear reaction within the IQMD frame is described to study the photo- absorption cross section and π meson production, and the simulation results are compared with some available experimental data as well as the Giessen Boltzmann-Uehling-Uhlenbeck model.

A VISCOPLASTIC MODEL BASED ON NO-YIELD-SURFACE CONCEPT

The elasticjviscoplastic constitutive equation which describes deformation law of metal materials was suggested based on no-yield-surface concept and thermal activation theory of dislocation. The equation which takes account of effects of strain-rate, strain history, strain-rate history, hardening and temperature has stronger physical basis.Comparison of the theoretical prediction with experimental results of mechanical behaviours of Ti under conditions of uniaxial stress and room temperature shows good consistency.

Reduced Model Based Control of Two Link Flexible Space Robot

Model based control schemes use the inverse dynamics of the robot arm to produce the main torque component necessary for trajectory tracking. For model-based controller one is required to know the model parameters accurately. This is a very difficult task especially if the manipulator is flexible. So a reduced model based controller has been developed, which requires only the information of space robot base velocity and link parameters. The flexible link is modeled as Euler Bernoulli beam. To simplify the analysis we have considered Jacobian of rigid manipulator. Bond graph modeling is used to model the dynamics of the system and to devise the control strategy. The scheme has been verified using simulation for two links flexible space manipulator.

Application of the Improved Generalized Autoregressive Conditional Heteroskedast Model Based on the Autoregressive Integrated Moving Average Model in Data Analysis

This study firstly improved the Generalized Autoregressive Conditional Heteroskedast model for the issue that financial product sales data have singular information when applying this model, and the improved outlier detection method was used to detect the location of outliers, which were processed by the iterative method. Secondly, in order to describe the peak and fat tail of the financial time series, as well as the leverage effect, this work used the skewed-t Asymmetric Power Autoregressive Conditional Heteroskedasticity model based on the Autoregressive Integrated Moving Average Model to analyze the sales data. Empirical analysis showed that the model considering the skewed distribution is effective.

Evaluation of the Performance of Financial Support for Agriculture in Guizhou Province Using Secondary Relative Benefit Model Based on DEA

We use the secondary relative benefit model based on DEA to evaluate the performance of agricultural financial expenditure in Guizhou Province, which can give due consideration to the production effectiveness determined by objective natural conditions, and management effectiveness of all regions (as decision-making body) in the use of financial fund for supporting agriculture. In general, there is north-south gradient difference in the performance of financial support for agriculture between regions in Guizhou Province. The drought in 2010 has significant impact on the technical efficiency in the whole province; the performance score of each item in Liupanshui City and Southwest Guizhou is very low; the technical efficiency and management efficiency in most regions need to be improved. In order to improve the performance of financial support for agriculture, we need to ensure the scale of input; at the same time, provide appropriate preferential financial policies for agricultural infrastructure, especially the construction of rural water conservancy, development and promotion of agricultural science and technology, and other fields; adopt the way of special check and acceptance of supporting projects to strengthen the use management of the fund for agriculture.

A New Approach to Intelligent Model Based Predictive Control Scheme

This paper describes a new approach to intelligent model based predictive control scheme for deriving a complex system. In the control scheme presented, the main problem of the linear model based predictive control theory in dealing with severe nonlinear and time variant systems is thoroughly solved. In fact, this theory could appropriately be improved to a perfect approach for handling all complex systems, provided that they are firstly taken into consideration in line with the outcomes presented. This control scheme is organized based on a multi-fuzzy-based predictive control approach as well as a multi-fuzzy-based predictive model approach, while an intelligent decision mechanism system (IDMS) is used to identify the best fuzzy-based predictive model approach and the corresponding fuzzy-based predictive control approach, at each instant of time. In order to demonstrate the validity of the proposed control scheme, the single linear model based generalized predictive control scheme is used as a benchmark approach. At last, the appropriate tracking performance of the proposed control scheme is easily outperformed in comparison with previous one.

Model-Based Systems Engineering Approach to Design a Human Settlement to Better Serve Displaced People

The challenge of transitioning from temporary humanitarian settlements to more sustainable human settlements is due to a significant increase in the number of forcibly displaced people over recent decades, difficulties in providing social services that meet the required standards, and the prolongation of emergencies. Despite this challenging context, short-term considerations continue to guide their planning and management rather than more integrated, longer-term perspectives, thus preventing viable, sustainable development. Over the years, the design of humanitarian settlements has not been adapted to local contexts and perspectives, nor to the dynamics of urbanization and population growth and data. In addition, the current approach to temporary settlement harms the environment and can strain limited resources. Inefficient land use and ad hoc development models have compounded difficulties and generated new challenges. As a result, living conditions in settlements have deteriorated over the last few decades and continue to pose new challenges. The stakes are such that major shortcomings have emerged along the way, leading to disruption, budget overruns in a context marked by a steady decline in funding. However, some attempts have been made to shift towards more sustainable approaches, but these have mainly focused on vague, sector-oriented themes, failing to consider systematic and integration views. This study is a contribution in addressing these shortcomings by designing a model-driving solution, emphasizing an integrated system conceptualized as a system of systems. This paper proposes a new methodology for designing an integrated and sustainable human settlement model, based on Model-Based Systems Engineering and a Systems Modeling Language to provide valuable insights toward sustainable solutions for displaced populations aligning with the United Nations 2030 agenda for sustainable development.

A Custom Manipulator for Dental Implantation Through Model-Based Design

This paper presents a Model-Based Design(MBD)approach for the design and control of a customized manipulator intended for drilling and position-ing of dental implants accurately with minimal human intervention.While performing an intra-oral surgery for a prolonged duration within a limited oral cavity,the tremor of dentist's hand is inevitable.As a result,wielding the drilling tool and inserting the dental implants safely in accurate position and orientation is highly challenging even for experienced dentists.Therefore,we introduce a customized manipulator that is designed ergonomically by taking in to account the dental chair specifications and anthropomorphic data such that it can be readily mounted onto the existing dental chair.The manipulator can be used to drill holes for dental inserts and position them with improved accuracy and safety.Further-more,a thorough multi-body motion analysis of the manipulator was carried out by creating a virtual prototype of the manipulator and simulating its controlled movements in various scenarios.The overall design was prepared and validated in simulation using Solid works,MATLAB and Simulink through Model Based Design(MBD)approach.The motion simulation results indicate that the manipulator could be built as a prototype readily.

DiagDO: an efficient model based diagnosis approach with multiple observations

Model-based diagnosis(MBD)with multiple observations shows its significance in identifying fault location.The existing approaches for MBD with multiple observations use observations which is inconsistent with the prediction of the system.In this paper,we proposed a novel diagnosis approach,namely,the Diagnosis with Different Observations(DiagDO),to exploit the diagnosis when given a set of pseudo normal observations and a set of abnormal observations.Three ideas are proposed in this paper.First,for each pseudo normal observation,we propagate the value of system inputs and gain fanin-free edges to shrink the size of possible faulty components.Second,for each abnormal observation,we utilize filtered nodes to seek surely normal components.Finally,we encode all the surely normal components and parts of dominated components into hard clauses and compute diagnosis using the MaxSAT solver and MCS algorithm.Extensive tests on the ISCAS'85 and ITC'99 benchmarks show that our approach performs better than the state-of-the-art algorithms.

A Triple Nexus Water-Energy-Housing (WEH) Framework Modelling towards Improved Decision-Making in Humanitarian Operations

Given the challenges facing most humanitarian operations worldwide, a change of approach is needed to ensure greater sustainability of humanitarian settlements right from the planning stage. Some studies attribute unsustainability to inadequate provision of basic resources and highlight the apparent bottlenecks that prevent access to the meaningful data needed to plan and remedy problems. Most operations have relied on an “ad hoc ism” approach, employing parallel and disconnected data processing methods, resulting in a wide range of data being collected without subsequent prioritization to optimize interconnections that could enhance performance. There have been little efforts to study the trade-offs potentially at stake. This work proposes a new framework enabling all subsystems to operate in a single system and focusing on data processing perspective. To achieve this, this paper proposes a Triple Nexus Framework as an attempt to integrate water, energy, and housing sector data derived from a specific sub-system within the overall system in the application of Model-Based Systems Engineering. Understanding the synergies between water, energy, and housing, Systems Engineering characterizes the triple nexus framework and identifies opportunities for improved decision-making in processing operational data from these sectors. Two scenarios illustrate how an integrated platform could be a gateway to access meaningful operational data in the system and a starting point for modeling integrated human settlement systems. Upon execution, the model is tested for nexus megadata processing, and the optimization simulation yielded 67% satisfactory results, demonstrating that an integrated system could improve sustainability, and that capacity building in service delivery is more than beneficial.

A Cautionary Note on the Application of GIS in Spatial Optimization Modeling

Spatial optimization as part of spatial modeling has been facilitated significantly by integration with GIS techniques. However, for certain research topics, applying standard GIS techniques may create problems which require attention. This paper serves as a cautionary note to demonstrate two problems associated with applying GIS in spatial optimization, using a capacitated p-median facility location optimization problem as an example. The first problem involves errors in interpolating spatial variations of travel costs from using kriging, a common set of techniques for raster files. The second problem is inaccuracy in routing performed on a graph directly created from polyline shapefiles, a common vector file type. While revealing these problems, the paper also suggests remedies. Specifically, interpolation errors can be eliminated by using agent-based spatial modeling while the inaccuracy in routing can be improved through altering the graph topology by splitting the long edges of the shapefile. These issues suggest the need for caution in applying GIS in spatial optimization study.

原料性质大幅变化情况下催化重整Delta-Base数据的生成方法

针对催化重整原料性质变化幅度较大的情况,提出采用变步长计算结合分子水平机理模型生成装置Delta-Base数据的方法。该方法通过计算原料性质扰动时产品质量分数变化量绝对值随原料性质变化量绝对值的变化率;并将该变化率的值域分成若干等份,根据每次计算得到变化率值域的范围不同,选择下一步计算时的变量扰动步长;继而在计算过程中取每次变量扰动的中点值产品质量分数进行验证,从而在提高计算效率的同时保证了计算结果的准确性。结果表明:利用该方法计算得到的各产品质量分数相对误差较小,基本不超过2.5%;对计算数据拟合可得到不同产品质量分数数据拟合方程,通过拟合方程可生成芳烃潜含量变化三阶段Delta-Base数据;比较原料芳烃潜含量(w)为42%时的产品预测结果,发现Delta-Base数据预测值和拟合方程计算值的平均偏差均为0.16%,说明该方法具有很好的准确性,利用分子水平机理模型生成的Delta-Base数据更能反映真实的分子反应历程。

Multi-agent Based Hierarchy Simulation Models of Carrier-based Aircraft Catapult Launch

With the aid of multi-agent based modeling approach to complex systems, the hierarchy simulation models of carrier-based aircraft catapult launch are developed. Ocean, carrier, aircraft, and atmosphere are treated as aggregation agents, the detailed components like catapult, landing gears, and disturbances are considered as meta-agents, which belong to their aggregation agent. Thus, the model with two layers is formed i.e. the aggregation agent layer and the meta-agent layer. The information communication among all agents is described. The meta-agents within one aggregation agent communicate with each other directly by information sharing, but the meta-agents, which belong to different aggregation agents exchange their information through the aggregation layer first, and then perceive it from the sharing environment, that is the aggregation agent. Thus, not only the hierarchy model is built, but also the environment perceived by each agent is specified. Meanwhile, the problem of balancing the independency of agent and the resource consumption brought by real-time communication within multi-agent system （MAS） is resolved. Each agent involved in carrier-based aircraft catapult launch is depicted, with considering the interaction within disturbed atmospheric environment and multiple motion bodies including carrier, aircraft, and landing gears. The models of reactive agents among them are derived based on tensors, and the perceived messages and inner frameworks of each agent are characterized. Finally, some results of a simulation instance are given. The simulation and modeling of dynamic system based on multi-agent system is of benefit to express physical concepts and logical hierarchy clearly and precisely. The system model can easily draw in kinds of other agents to achieve a precise simulation of more complex system. This modeling technique makes the complex integral dynamic equations of multibodies decompose into parallel operations of single agent, and it is convenient to expand, maintain, and reuse the program codes.

Exploration of the Impact Mechanism of Government Credibility Based on Variable Screening Method

Government credibility is an important asset of contemporary national governance, an important criterion for evaluating government legitimacy, and a key factor in measuring the effectiveness of government governance. In recent years, researchers’ research on government credibility has mostly focused on exploring theories and mechanisms, with little empirical research on this topic. This article intends to apply variable selection models in the field of social statistics to the issue of government credibility, in order to achieve empirical research on government credibility and explore its core influencing factors from a statistical perspective. Specifically, this article intends to use four regression-analysis-based methods and three random-forest-based methods to study the influencing factors of government credibility in various provinces in China, and compare the performance of these seven variable selection methods in different dimensions. The research results show that there are certain differences in simplicity, accuracy, and variable importance ranking among different variable selection methods, which present different importance in the study of government credibility issues. This study provides a methodological reference for variable selection models in the field of social science research, and also offers a multidimensional comparative perspective for analyzing the influencing factors of government credibility.

IFAM与24Model的对比研究

为完善和推动事故致因理论的发展,提高事故防控水平,在对信息流事故致因模型(IFAM)和事故致因2-4模型(24Model)理论基础、组成要素和分析过程对比研究的基础上,通过实例分析辨识二者之间的异同。研究结果表明:IFAM与24Model都有较强的理论基础,部分组成要素存在对应关系,但原因类别划分存在差异。IFAM以信息流和组织为研究对象,研究过程相对复杂,更适用于分析单起事故;24Model以组织为研究对象,事故原因模块通用性和逻辑性强,适用于分析单起或某类事故。在实际应用中,IFAM与24Model均可用于事故调查分析和事故分级定责,具有一定的理论和实践价值。IFAM通过信息流表征事故致因,直观描述组织外部原因因素,但对个体能力的深入研究欠缺;而24Model认为组织外部因素需要通过组织内部原因模块的欠缺体现,认为个体能力是引发事故的间接原因并进行细致分析,但对组织间相关关系的探究欠缺。研究结果可为事故预防工作提供新视角和理论支撑。

Hierarchy Bayesian model based services awareness of high-speed optical access networks

As the speed of optical access networks soars with ever increasing multiple services, the service-supporting ability of optical access networks suffers greatly from the shortage of service awareness. Aiming to solve this problem, a hierarchy Bayesian model based services awareness mechanism is proposed for high-speed optical access networks. This approach builds a so-called hierarchy Bayesian model, according to the structure of typical optical access networks. Moreover, the proposed scheme is able to conduct simple services awareness operation in each optical network unit(ONU) and to perform complex services awareness from the whole view of system in optical line terminal(OLT). Simulation results show that the proposed scheme is able to achieve better quality of services(Qo S), in terms of packet loss rate and time delay.