High-precision and wide-range real-time neutron flux monitor system through multipoint linear calibration

The neutron flux monitor(NFM)system is an important diagnostic subsystem introduced by large nuclear fusion devices such as international thermonuclear experimental reactor(ITER),Japan torus-60,tokamak fusion test reactor,and HL-2 A.Neutron fluxes can provide real-time parameters for nuclear fusion,including neutron source intensity and fusion power.Corresponding to different nuclear reaction periods,neutron fluxes span over seven decades,thereby requiring electronic devices to operate in counting and Campbelling modes simultaneously.Therefore,it is crucial to design a real-time NFM system to encompass such a wide dynamic range.In this study,a high-precision NFM system with a wide measurement range of neutron flux is implemented using realtime multipoint linear calibration.It can automatically switch between counting and Campbelling modes with variations in the neutron flux.We established a testing platform to verify the feasibility of the NFM system,which can output the simulated neutron signal using an arbitrary waveform generator.Meanwhile,the accurate calibration interval of the Campbelling mode is defined well.Based on the above-mentioned design,the system satisfies the requirements,offering a dynamic range of 10~8 cps,temporal resolution of 1 ms,and maximal relative error of 4%measured at the signal-to-noise ratio of 15.8 dB.Additionally,the NFM system is verified in a field experiment involving HL-2 A,and the measured neutron flux is consistent with the results.

Development of readout electronics for bunch arrival-time monitor system at SXFEL

A bunch arrival-time monitor(BAM) system,based on electro-optical intensity modulation scheme, is under study at Shanghai Soft X-ray Free Electron Laser.The aim of the study is to achieve high-precision time measurement for minimizing bunch fluctuations. A readout electronics is developed to fulfill the requirements of the BAM system. The readout electronics is mainly composed of a signal conditioning circuit, field-programmable gate array(FPGA), mezzanine card(FMC150), and powerful FPGA carrier board. The signal conditioning circuit converts the laser pulses into electrical pulse signals using a photodiode. Thereafter, it performs splitting and low-noise amplification to achieve the best voltage sampling performance of the dual-channel analog-to-digital converter(ADC) in FMC150. The FMC150 ADC daughter card includes a 14-bit 250 Msps dual-channel high-speed ADC,a clock configuration, and a management module. The powerful FPGA carrier board is a commercial high-performance Xilinx Kintex-7 FPGA evaluation board. To achieve clock and data alignment for ADC data capture at a high sampling rate, we used ISERDES, IDELAY, and dedicated carry-in resources in the Kintex-7 FPGA. This paper presents a detailed development of the readout electronics in the BAM system and its performance.

Monitor System for Protection Device Based on Embedded RTOS

For the purpose of the monitor system in digital protection, the embedded real-time operating system (RTOS) and the embedded GUI (Graphical User Interface) is introduced to design the monitor system. Combining the necessity and the application value of the operation system, the choice of embedded Linux and Qt/Embedded is completely viable for the monitor system in digital protection for generator-transformer sets. The design with embedded Linux and embedded GUI enriches system information, increases developing efficiency and improve the generality.

Smart Meter Development for Cloud-Based Home Electricity Monitor System

Αcloud-based home electricity data-monitoring system,which is based on an Arduino Mega controller,is proposed for monitoring the electricity consumption(electrical power)and power quality(PQ)in home.This system is also capable of monitoring the fundamental frequency and supply-voltage transients to ensure that the appliances operate in a safe operation range.The measured data(voltage and current)are transmitted through a Wi Fi device between the Arduino controller and server.The transmission control protocol(TCP)server is set up to acquire the high-data transmission rate.The server system immediately displays the calculated parameters and the waveform of the acquired signal.A comparison with a standard measurement device shows that the proposed system,which can be built at a low cost,exhibits the same functions as a factory product.

The control and monitor system for the BESⅢ ETOF/MRPC beam test

A test system is developed for the BESIII ETOF/MRPC beam tests of data acquisition, environment monitoring and automatic control. The software framework is based on the CAMAC bus, VME bus and Serial Port,which are responsible for communications with the detectors. The monitor system works well in the beam test.

ADAPTIVE ERROR-LIMITING METHOD SUITABLE FOR THE WALSH CODE SHUTTING MULTIPLEXING IN THE MINE MONITOR SYSTEM

Through the analysis for the process of Walsh modulation and demodula tion,the adaptive error-limiting method suitable for the Walsh code shutting multiplex ing in the mine monitor system is advanced in this article. It is proved by theoretical analysis and circuit experiments that this method is easy to carry out and can not only improve the quality of information transmission but also meet the requirement of the system patrol test time without the increasement of system investment.

Design and Construction of Automatic Monitoring System for Open-pit Coal Mine Slopes

[Objectives]To monitor the stability of open-pit coal mine slopes in real time and ensure the safety of coal mine production.[Methods]The automatic monitoring system of coal mine slope was explored in depth,and the core functions of the system were designed comprehensively.According to the design function of the automatic monitoring system,the slope automatic monitoring system was constructed.Besides,in accordance with the actual situation of the slope,the monitoring frequency of slopes was set scientifically,and the key indicators such as rainfall,deep displacement and surface displacement of the slopes were monitored in an all-round and multi-angle way.[Results]During the monitoring period,the overall condition of the slope remained good,and no landslides or other geological disasters occurred.At the same time,the overall rainfall in the slope area remained low.In terms of monitoring data,the horizontal displacement and settlement of the slopes increased first and then tended to be stable.Specifically,the maximum horizontal displacement during the monitoring period was 22.74 mm,while the maximum settlement was 18.65 mm.[Conclusions]The automatic slope monitoring system has obtained remarkable achievements in practical application.It not only improves the accuracy and efficiency of slope stability monitoring,but also provides valuable reference experience for similar projects.

Development of Spectral Features for Monitoring Rice Bacterial Leaf Blight Disease Using Broad-Band Remote Sensing Systems

As an important rice disease, rice bacterial leaf blight (RBLB, caused by the bacterium Xanthomonas oryzae pv.oryzae), has become widespread in east China in recent years. Significant losses in rice yield occurred as a result ofthe disease’s epidemic, making it imperative to monitor RBLB at a large scale. With the development of remotesensing technology, the broad-band sensors equipped with red-edge channels over multiple spatial resolutionsoffer numerous available data for large-scale monitoring of rice diseases. However, RBLB is characterized by rapiddispersal under suitable conditions, making it difficult to track the disease at a regional scale with a single sensorin practice. Therefore, it is necessary to identify or construct features that are effective across different sensors formonitoring RBLB. To achieve this goal, the spectral response of RBLB was first analyzed based on the canopyhyperspectral data. Using the relative spectral response (RSR) functions of four representative satellite or UAVsensors (i.e., Sentinel-2, GF-6, Planet, and Rededge-M) and the hyperspectral data, the corresponding broad-bandspectral data was simulated. According to a thorough band combination and sensitivity analysis, two novel spectralindices for monitoring RBLB that can be effective across multiple sensors (i.e., RBBRI and RBBDI) weredeveloped. An optimal feature set that includes the two novel indices and a classical vegetation index was formed.The capability of such a feature set in monitoring RBLB was assessed via FLDA and SVM algorithms. The resultdemonstrated that both constructed novel indices exhibited high sensitivity to the disease across multiple sensors.Meanwhile, the feature set yielded an overall accuracy above 90% for all sensors, which indicates its cross-sensorgenerality in monitoring RBLB. The outcome of this research permits disease monitoring with different remotesensing data over a large scale.

Long-term trends in the abundance and breeding performance in Adélie penguins:the Argentine Ecosystem Monitoring Program

In this work,we report long-term trends in the abundance and breeding performance of Adélie penguins(Pygoscelis adeliae)nesting in three Antarctic colonies(i.e.,at Martin Point,South Orkneys Islands;Stranger Point/Cabo Funes,South Shetland Islands;and Esperanza/Hope Bay in the Antarctic Peninsula)from 1995/96 to 2022/23.Using yearly count data of breeding groups selected,we observed a decline in the number of breeding pairs and chicks in crèche at all colonies studied.However,the magnitude of change was higher at Stranger Point than that in the remaining colonies.Moreover,the index of breeding success,which was calculated as the ratio of chicks in crèche to breeding pairs,exhibited no apparent trend throughout the study period.However,it displayed greater variability at Martin Point compared to the other two colonies under investigation.Although the number of chicks in crèche of Adélie penguins showed a declining pattern,the average breeding performance was similar to that reported in gentoo penguin colonies,specifically,those undergoing a population increase(even in sympatric colonies facing similar local conditions).Consequently,it is plausible to assume a reduction of the over-winter survival as a likely cause of the declining trend observed,at least in the Stranger Point and Esperanza colonies.However,we cannot rule out local effects during the breeding season affecting the Adélie population of Martin Point.

Personalized Health Monitoring Systems: Integrating Wearable and AI

The integration of wearable technologies and artificial intelligence (AI) has revolutionized healthcare, enabling advanced personal health monitoring systems. This article explores the transformative impact of wearable technologies and AI on healthcare, highlighting the development and theoretical application of the Integrated Personal Health Monitoring System (IPHMS). By integrating data from various wearable devices, such as smartphones, Apple Watches, and Oura Rings, the IPHMS framework aims to revolutionize personal health monitoring through real-time alerts, comprehensive tracking, and personalized insights. Despite its potential, the practical implementation faces challenges, including data privacy, system interoperability, and scalability. The evolution of healthcare technology from traditional methods to AI-enhanced wearables underscores a significant advancement towards personalized care, necessitating further research and innovation to address existing limitations and fully realize the benefits of such integrated health monitoring systems.

Research on Smart Energy Monitoring and Management System Based on Digital Twin Technology

Smart energy monitoring and management system lays a foundation for the application and development of smart energy. However, in recent years, the work efficiency of smart energy development enterprises has generally been low, and there is an urgent need to improve the application efficiency, resilience and sustainability of smart energy monitoring and management system. Digital twin technology provides a data-centric solution to improve smart energy monitoring and management system, bringing an opportunity to transform passive infrastructure assets into data-centric systems. This paper expounds on the concept and key technologies of digital twin, and designs a smart energy monitoring and management system based on digital twin technology, which has dual significance for promoting the development of smart energy field and promoting the application of digital twin.

Research on a Comprehensive Monitoring System for Tunnel Operation based on the Internet of Things and Artificial Intelligence Identification Technology

This article proposes a comprehensive monitoring system for tunnel operation to address the risks associated with tunnel operations.These risks include safety control risks,increased traffic flow,extreme weather events,and movement of tectonic plates.The proposed system is based on the Internet of Things and artificial intelligence identification technology.The monitoring system will cover various aspects of tunnel operations,such as the slope of the entrance,the structural safety of the cave body,toxic and harmful gases that may appear during operation,excessively high and low-temperature humidity,poor illumination,water leakage or road water accumulation caused by extreme weather,combustion and smoke caused by fires,and more.The system will enable comprehensive monitoring and early warning of fire protection systems,accident vehicles,and overheating vehicles.This will effectively improve safety during tunnel operation.

Design of IoT-based Volatile Organic Compounds Monitoring System

Volatile organic compounds(VOC)gas detection devices based on semiconductor sensors have become a common method due to their low cost,simple principle,and small size.However,with the continuous development of materials science,various new materials have been applied in the fabrication of gas sensors,but these new materials have more stringent requirements for operating temperature,which cannot be met by existing sensor modules on the market.Therefore,this paper proposes a temperature-adjustable sensor module and designs an environmental monitoring system based on the STM32F103RET6 microprocessor.This system primarily utilizes multiple semiconductor gas sensors to monitor and record the concentrations of various harmful gases in different environments.It can also monitor real-time temperature,humidity,and latitude and longitude in the current environment,and upload the data to the Internet of Things via 4G communication.This system has the advantages of small size,portability,and low cost.Experimental results show that the sensor module can achieve precise control of operating temperature to a certain extent,with an average temperature error of approximately 3%.The monitoring system demonstrates a certain level of accuracy in detecting target gases and can promptly upload the data to a cloud platform for storage and processing.A comparison with professional testing equipment shows that the sensitivity curves of each sensor exhibit similarity.This study provides engineering and technical references for the application of VOC gas sensors.

Application of GNSS-PPP on Dynamic Deformation Monitoring of Offshore Platforms

The real-time dynamic deformation monitoring of offshore platforms under environmental excitation is crucial to their safe operation.Although Global Navigation Satellite System-Precise Point Positioning(GNSS-PPP)has been considered for this purpose,its monitoring accuracy is relatively low.Moreover,the influence of background noise on the dynamic monitoring accuracy of GNSS-PPP remains unclear.Hence,it is imperative to further validate the feasibility of GNSS-PPP for deformation monitoring of offshore platforms.To address these concerns,vibration table tests with different amplitudes and frequencies are conducted.The results demonstrate that GNSS-PPP can effectively monitor horizontal vibration displacement as low as±30 mm,which is consistent with GNSS-RTK.Furthermore,the spectral characteristic of background noise in GNSS-PPP is similar to that of GNSS-RTK(Real Time Kinematic).Building on this observation,an improved Complete Ensemble Empirical Mode Decomposition with Adaptive Noise(CEEMDAN)has been proposed to de-noise the data and enhance the dynamic monitoring accuracy of GNSS-PPP.Field monitoring application research is also undertaken,successfully extracting and analyzing the dynamic deformation of an offshore platform structure under environmental excitation using GNSS-PPP monitoring in conjunction with improved CEEMDAN de-noising.By comparing the de-noised dynamic deformation trajectories of the offshore platform during different periods,it is observed that the platform exhibits reversible alternating vibration responses under environmental excitation,with more pronounced displacement deformation in the direction of load action.The research results confirm the feasibility and potential of GNSS-PPP for dynamic deformation monitoring of offshore platforms.

An IoT-Based Aquaculture Monitoring System Using Firebase

Indonesia is a producer in the fisheries sector,with production reaching 14.8 million tons in 2022.The production potential of the fisheries sector can be optimally optimized through aquaculture management.One of the most important issues in aquaculture management is how to efficiently control the fish pond water conditions.IoT technology can be applied to support a fish pond aquaculture monitoring system,especially for catfish species(Siluriformes),in real-time and remotely.One of the technologies that can provide this convenience is the IoT.The problem of this study is how to integrate IoT devices with Firebase’s cloud data system to provide reliable and precise data,which makes it easy for fish cultivators to monitor fishpond conditions in real time and remotely.The IoT aquaculture fishpond monitoring use 3 parameters:(1)water temperature;(2)pHwater level;and(3)turbidity level of pond water.IoT devices use temperature sensors,pH sensors,and turbidity sensors,which are integrated with a microcontroller and Wi-Fi module.Data from sensor readings are sent to the Firebase cloud via theWi-Fi module so that it can be accessed in real time by end users with an Androidbased mobile app.The findings are(1)the IoT-based aquaculture monitoring system device has a low error rate in measuring temprature,pH,and turbidity with a percentage of 1.75%,1.94% and 9.78%,respectively.Overall,the total average error of the three components is 4.49%;(2)in cost analysis,IoT-based has a cost-effectiveness of 94.21% compared to labor costs.An IoT-based aquaculture monitoring system using Firebase can be effectively used as a technology for monitoring fish pond conditions in real-time and remotely for fish cultivators that contribute to providing an IoT-based aquaculture monitoring system that produces valid data,is precise,is easy to implement,and is a low-cost system.

PIMS:An Efficient Process Integrity Monitoring System Based on Blockchain and Trusted Computing in Cloud-Native Context

With the advantages of lightweight and high resource utilization,cloud-native technology with containers as the core is gradually becoming themainstreamtechnical architecture for information infrastructure.However,malware attacks such as Doki and Symbiote threaten the container runtime’s security.Malware initiates various types of runtime anomalies based on process form(e.g.,modifying the process of a container,and opening the external ports).Fortunately,dynamic monitoring mechanisms have proven to be a feasible solution for verifying the trusted state of containers at runtime.Nevertheless,the current routine dynamic monitoring mechanisms for baseline data protection are still based on strong security assumptions.As a result,the existing dynamicmonitoringmechanismis still not practical enough.To ensure the trustworthiness of the baseline value data and,simultaneously,to achieve the integrity verification of the monitored process,we combine blockchain and trusted computing to propose a process integrity monitoring system named IPMS.Firstly,the hardware TPM 2.0 module is applied to construct a trusted security foundation for the integrity of the process code segment due to its tamper-proof feature.Then,design a new format for storing measurement logs,easily distinguishing files with the same name in different containers from log information.Meanwhile,the baseline value data is stored on the blockchain to avoidmalicious damage.Finally,trusted computing technology is used to perform fine-grained integrity measurement and remote attestation of processes in a container,detect abnormal containers in time and control them.We have implemented a prototype system and performed extensive simulation experiments to test and analyze the functionality and performance of the PIMS.Experimental results show that PIMS can accurately and efficiently detect tampered processes with only 3.57% performance loss to the container.

Data-Driven Approach for Condition Monitoring and Improving Power Output of Photovoltaic Systems

Increasing renewable energy targets globally has raised the requirement for the efficient and profitable operation of solar photovoltaic(PV)systems.In light of this requirement,this paper provides a path for evaluating the operating condition and improving the power output of the PV system in a grid integrated environment.To achieve this,different types of faults in grid-connected PV systems(GCPVs)and their impact on the energy loss associated with the electrical network are analyzed.A data-driven approach using neural networks(NNs)is proposed to achieve root cause analysis and localize the fault to the component level in the system.The localized fault condition is combined with a parallel operation of adaptive neurofuzzy inference units(ANFIUs)to develop a power mismatch-based control unit(PMCU)for improving the power output of the GCPV.To develop the proposed framework,a 10-kW single-phase GCPV is simulated for training the NN-based anomaly detection approach with 14 deviation signals.Further,the developed algorithm is combined with the PMCU implemented with the experimental setup of GCPV.The results identified 98.2%training accuracy and 43000 observations/sec prediction speed for the trained classifier,and improved power output with reduced voltage and current harmonics for the grid-connected PV operation.

Natural Disaster Risk Monitoring for Immovable Cultural Relics Based on Digital Twin

Natural disaster risk monitoring is an important task for disaster prevention and reduction.In the case of immovable cultural relics,however,the feedback mechanism,risk factors,monitoring logic,and monitoring indicators of natural disaster risk monitoring are complex.How to achieve intelligent perception and monitoring of natural disaster risk for immovable cultural relics has always been a focus and a challenge for researchers.Based on the analysis of the concepts and issues related to the natural disaster risk of immovable cultural relics,this paper proposes a framework for natural disaster risk monitoring for immovable cultural relics based on the digital twin.This framework focuses on risk monitoring,including the physical entities of natural disaster risk for immovable cultural relics,monitoring indicators,and virtual entity construction.A platform for monitoring the natural disaster risk of immovable cultural relics is proposed.Using the Puzhou Ancient City Site as a test bed,the proposed concept can be used for monitoring the natural disaster risk of immovable cultural relics at different scales.

Wearable Smart Sensor System for Medical Monitoring with an Assessment of the Level of Blood Loss and Pain Shock Because of Trauma or Injury

Blood loss in peacetime is mainly due to the normal menstrual cycle in women or diseases with surgical intervention. In wartime, blood loss in military personnel is a characteristic sign of a closed or open injury of the body during internal or external bleeding. Access to clinical care for wounded military personnel injured on the battlefield is limited and has long delays compared to patients in peacetime. Most of the deaths of wounded military personnel on the battlefield occur within the first hour after being wounded. The most common causes are delay in providing medical care, loss of time for diagnosis, delay in stabilization of pain shock and large blood loss. Some help in overcoming these problems is provided by the data in the individual capsule, which each soldier of the modern army possesses;however, data in an individual capsule is not sufficient to provide emergency medical care in field and hospital conditions. This paper considers a project for development of a smart real-time monitoring wearable system for blood loss and level of shock stress in wounded persons on the battlefield, which provides medical staff in field and hospital conditions with the necessary information to give timely medical care. Although the hospital will require additional information, the basic information about the victims will already be known before he enters the hospital. It is important to emphasize that the key term in this approach is monitoring. It is tracking, and not a one-time measurement of indicators, that is crucial in a valid definition of bleeding.

A Deep CNN-LSTM-Based Feature Extraction for Cyber-Physical System Monitoring

A potential concept that could be effective for multiple applications is a“cyber-physical system”(CPS).The Internet of Things(IoT)has evolved as a research area,presenting new challenges in obtaining valuable data through environmental monitoring.The existing work solely focuses on classifying the audio system of CPS without utilizing feature extraction.This study employs a deep learning method,CNN-LSTM,and two-way feature extraction to classify audio systems within CPS.The primary objective of this system,which is built upon a convolutional neural network(CNN)with Long Short Term Memory(LSTM),is to analyze the vocalization patterns of two different species of anurans.It has been demonstrated that CNNs,when combined with mel-spectrograms for sound analysis,are suitable for classifying ambient noises.Initially,the data is augmented and preprocessed.Next,the mel spectrogram features are extracted through two-way feature extraction.First,Principal Component Analysis(PCA)is utilized for dimensionality reduction,followed by Transfer learning for audio feature extraction.Finally,the classification is performed using the CNN-LSTM process.This methodology can potentially be employed for categorizing various biological acoustic objects and analyzing biodiversity indexes in natural environments,resulting in high classification accuracy.The study highlights that this CNNLSTM approach enables cost-effective and resource-efficient monitoring of large natural regions.The dissemination of updated CNN-LSTM models across distant IoT nodes is facilitated flexibly and dynamically through the utilization of CPS.