Sludge granulation and efficiency of phase separator in UASB reactor treating combined industrial effluent

Sludge granulation and the effect of gas-liquid-solid separator （GLSS） design on the efficiency of upflow anaerobic sludge blanket （UASB） and upflow anaerobic sludge filter （UASF） reactors, operating at HRTs ranging from 3 to 12 h was investigated. VSS/TS ratio gradually increased in both the reactors with increasing sludge age （from 0.5 to more than 0.7 for UASB reactor and 0.012 to 0.043 for UASF reactor）. X-Ray diffraction analysis of the UASF sludge showed the presence of expanding clays revealing its additional absorption capability. Fuoraphyllite and albite precipitation related to excellular polymers of the microbial shell structure, showed the extended growth of microorganisms during sludge granulation. A gradual decrease （82%-69%） in COD removal with decreasing HRT was apparent in UASF reactor. In case of UASB reactor, this decrease was marginal because addition of GLSS device significantly improved （14%-20%） the overall efficiency of the UASB reactor. GLSS enhanced the efficiency of the UASB reactor by increasing the settleability of suspended particles and accelerating the coagulation of colloidal particles due to the velocity gradient.

Flow Rate of He II Liquid-Vapor Phase Separator

Experimental results are presented for superfluid (He II) flow through porous plug liquid-vapor phase separators. Tests have been performed on seven porous plugs with different thicknesses or different permeabilities. The temperature was measured from 1.5K to 1.9K. Two flow regions were observed in small and large pressure and temperature differences regions respectively. The experimental data are compared with theoretical predictions. The performance and applicability of the basic theory are discussed. Hysteresis of the flow rate is also observed and discussed.

Phase separation and transcriptional regulation in cancer development

Liquid-liquid phase separation,a novel biochemical phenomenon,has been increasingly studied for its medical applications.It underlies the formation of membrane-less organelles and is involved in many cellular and biological processes.During transcriptional regulation,dynamic condensates are formed through interactions between transcriptional elements,such as transcription factors,coactivators,and mediators.Cancer is a disease characterized by uncontrolled cell proliferation,but the precise mechanisms underlying tumorigenesis often remain to be elucidated.Emerging evidence has linked abnormal transcriptional condensates to several diseases,especially cancer,implying that phase separation plays an important role in tumorigenesis.Condensates formed by phase separation may have an effect on gene transcription in tumors.In the present review,we focus on the correlation between phase separation and transcriptional regulation,as well as how this phenomenon contributes to cancer development.

Enhancement of vertical phase separation in sequentially deposited organic photovoltaics through the independent processing of additives

Herein,the impact of the independent control of processing additives on vertical phase separation in sequentially deposited (SD) organic photovoltaics (OPVs) and its subsequent effects on charge carrier kinetics at the electron donor-acceptor interface are investigated.The film morphology exhibits notable variations,significantly depending on the layer to which 1,8-diiodooctane (DIO) was applied.Grazing incidence wide-angle X-ray scattering analysis reveals distinctly separated donor/acceptor phases and vertical crystallinity details in SD films.Time-of-flight secondary ion mass spectrometry analysis is employed to obtain component distributions in diverse vertical phase structures of SD films depending on additive control.In addition,nanosecond transient absorption spectroscopy shows that DIO control significantly affects the dynamics of separated charges in SD films.In SD OPVs,DIO appears to act through distinct mechanisms with minimal restriction,depending on the applied layer.This study emphasizes the significance of morphological optimization in improving device performance and underscores the importance of independent additive control in the advancement of OPV technology.

A Cu-Pd alloy catalyst with partial phase separation for the electrochemical CO_(2) reduction reaction

Cu catalysts can convert CO_(2) through an electrochemical reduction reaction into a variety of useful carbon-based products.However,this capability provides an obstacle to increasing the selectivity for a single product.Herein,we report a simple fabrication method for a Cu-Pd alloy catalyst for use in a membrane electrode assembly(MEA)-based CO_(2) electrolyzer for the electrochemical CO_(2) reduction reaction(ECRR)with high selectivity for CO production.When the composition of the Cu-Pd alloy catalyst was fabricated at 6:4,the selectivity for CO increased and the production of multi-carbon compounds and hydrogen is suppressed.Introducing a Cu-Pd alloy catalyst with 6:4 ratio as the cathode of the MEAbased CO_(2) electrolyzer showed a CO faradaic efficiency of 92.8%at 2.4 V_(cell).We assumed that these results contributed from the crystal planes on the surface of the Cu-Pd alloy.The phases of the Cu-Pd alloy catalyst were partially separated through annealing to fabricate a catalyst with high selectivity for CO at low voltage and C_(2)H_4 at high voltage.The results of CO-stripping testing confirmed that when Cu partially separates from the lattice of the Cu-Pd alloy,the desorption of~*CO is suppressed,suggesting that C-C coupling reaction is favored.

Fluorinated semi-interpenetrating polymer networks for enhancing the mechanical performance and storage stability of polymer-bonded explosives by controlling curing and phase separation rates

Herein, the effect of fluoropolymer binders on the properties of polymer-bonded explosives(PBXs) was comprehensively investigated. To this end, fluorinated semi-interpenetrating polymer networks(semiIPNs) were prepared using different catalyst amounts(denoted as F23-CLF-30-D). The involved curing and phase separation processes were monitored using Fourier-transform infrared spectroscopy, differential scanning calorimetry, a haze meter and a rheometer. Curing rate constant and activation energy were calculated using a theoretical model and numerical method, respectively. Results revealed that owing to its co-continuous micro-phase separation structure, the F23-CLF-30-D3 semi-IPN exhibited considerably higher tensile strength and elongation at break than pure fluororubber F2314 and the F23-CLF-30-D0 semi-IPN because the phase separation and curing rates matched in the initial stage of curing.An arc Brazilian test revealed that F23-CLF-30-D-based composites used as mock materials for PBXs exhibited excellent mechanical performance and storage stability. Thus, the matched curing and phase separation rates play a crucial role during the fabrication of high-performance semi-IPNs;these factors can be feasibly controlled using an appropriate catalyst amount.

Physical information-enhanced graph neural network for predicting phase separation

Although phase separation is a ubiquitous phenomenon, the interactions between multiple components make it difficult to accurately model and predict. In recent years, machine learning has been widely used in physics simulations. Here,we present a physical information-enhanced graph neural network(PIENet) to simulate and predict the evolution of phase separation. The accuracy of our model in predicting particle positions is improved by 40.3% and 51.77% compared with CNN and SVM respectively. Moreover, we design an order parameter based on local density to measure the evolution of phase separation and analyze the systematic changes with different repulsion coefficients and different Schmidt numbers.The results demonstrate that our model can achieve long-term accurate predictions of order parameters without requiring complex handcrafted features. These results prove that graph neural networks can become new tools and methods for predicting the structure and properties of complex physical systems.

Solid-state NMR studies of proteins in condensed phases

Some proteins perform their biological functions by changing their material states through liquid-liquid phase separation.Upon phase separation,the protein condenses into a concentrated liquid phase and sometimes into a gel phase,changing its dynamic properties and intermolecular interactions,thereby regulating cellular functions.Although the biological significance of this phenomenon has been widely recognized by researchers,there is still a lack of a comprehensive understanding of the structural and dynamic properties of the protein in the condensed phase.In this phase,molecules usually contain domains with varied dynamic properties and undergo intermediate exchanges.Magic angle spinning(MAS)solid-state NMR(SSNMR)experiments are very powerful in studying rigid protein polymers such as amyloid.The incorporation of solution-like experiments into SSNMR and the development of J-coupling based MAS SSNMR techniques extend its ability to study partially mobile segments of proteins in a condensed liquid or gel phase which are not visible by solution NMR or dipolar-coupling based SSNMR.Therefore,it has been applied in studying protein condensation and has provided very important information that is hard to obtain by other techniques.

Time-resolved photoluminescence of anatase/rutile TiO_2 phase junction revealing charge separation dynamics

Junctions are an important structure that allows charge separation in solar cells and photocatalysts. Here, we studied the charge transfer at an anatase/rutile TiO2 phase junction using time-resolved photoluminescence spectroscopy. Visible （-S00 nm） and near-infrared （NIR, -830 nm） emissions were monitored to give insight into the photoinduced charges of anatase and rutile in the junction, respectively, New fast photoluminescence decay components appeared in the visible emission of futile-phase dominated TiO2 and in the NIR emission of many mixed phase TiO2samples. The fast decays confirmed that the charge separation occurred at the phase junction. The visible emission intensity from the mixed phase TiO2 increased, revealing that charge transfer from rutile to anatase was the main pathway. The charge separation slowed the microsecond time scale photolumines- cence decay rate for charge carriers in both anatase and rutile. However, the millisecond decay of the charge carriers in anatase TiO2 was accelerated, while there was almost no change in the charge carrier dynamics of rutile TiO2. Thus, charge separation at the anatase/rutile phase junction caused an increase in the charge carrier concentration on a microsecond time scale, because of slower electron-hole recombination. The enhanced photocatalytic activity previously observed at ana- tase/rutile phase junctions is likely caused by the improved charge carrier dynamics we report here. These findings may contribute to the development of improved photocatalytic materials.

Construction of Renewable Superhydrophobic Surfaces via Thermally Induced Phase Separation and Mechanical Peeling

We report a simple preparation method of a renewable superhydrophobic surface by thermally induced phase separation （TIPS） and mechanical peeling. Porous polyvinylidene fluoride （PVDF） membranes with hierarchical structures were prepared by a TIPS process under different cooling conditions, which were confirmed by scanning electron microscopy and mercury intrusion porosimetry. After peeling off the top layer, rough structures with hundreds of nanometers to several microns were obtained. A digital microscopy determines that the surface roughness of peeled PVDF membranes is much higher than that of the original PVDF membrane, which is important to obtain the superhydrophobicity. Water contact angle and sliding angle measurements demonstrate that the peeled membrane surfaces display super- hydrophobicity with a high contact angle （152°） and a low sliding angle （7.2°）. Moreover, the superhydrophobicity can be easily recovered for many times by a simple mechanical peeling, identical to the original superhydrophobicity. This simple preparation method is low cost, and suitable for large-scale industrialization, which may offer more opportunities for practical applications.

Exchange Bias Effect in Phase Separated La0.33Pr0.34Ca0.33MnO3 Thin Films

Exchange bias effect is observed in the phase separated La0.33Pr0.34Ca0.33MnO3 thin films. High exchange bias field of about 1 kOe is achieved at 4 K. The exchange bias effect in La0.33Pr0.34Ca0.33MnO3 thin films might originate from the intrinsic phase separation of the La0.33Pr0.34Ca0.33MnO3 or surface effect. The dependence of exchange bias effect on temperature, cooling field, and thickness is also investigated. This work would open an avenue to the application in the magnetic memory devices based on the phase separated manganites.

Effect of Diluent on the Morphology and Performance of IPP Hollow Fiber Microporous Membrane via Thermally Induced Phase Separation

Isotactic polypropylene （iPP） hollow fiber microporous membranes were prepared using thermally induced phase separation （TIPS） method. Di-n-butyl phthalate （DBP）, dioctyl phthalate （DOP）, and the mixed solvent were used as diluents. The effect of α （DOP mass fraction in diluent） on the morphology and performance of the hollow fiber was investigated. With increasing α, the morphology of the resulting hollow fiber changes from typical cellular structure to mixed structure, and then to typical particulate structure. As a result, the permeability of the hollow fiber increases sharply, and the mechanical properties of the hollow fiber decrease obviously. It is suggested that the morphology and performances of iPP hollow fiber microporous membrane can be controlled via adjusting the compatibility between iPP and diluent.

Phase separation in solvent extraction of cobalt from acidic sulfate solution using synergistic mixture containing dinonylnaphthalene sulfonic acid and 2-ethylhexyl 4-pyridinecarboxylate ester

Phase separation rate is a critical character in determining the usefulness of a solvent extraction system in hydrometallurgy. A survey of the synergistic mixture containing dinonylnaphthalene sulfonic acid (HDNNS) and 2-ethylhexly 4-pyridinecarboxylate ester (4PC) for the extraction of cobalt from acidic single metal sulfate solution was carried out to suggest how the physicochemical properties and the morphology of the reverse micelles in the loaded organic phase affect the phase separation. The results show that effective parameters affecting the phase separation are the viscosity and the excess water uptake of the loaded organic phase. It is obvious that the specific settling rate (SSR) decreases with the apparent increase of these two parameters. The measurement of small angle X-ray scattering (SAXS) proves that the morphology of the reversed micelles in the loaded organic phase changes evidently with the change of the specific settling rate (SSR).

Microporous carbon nanofibers prepared by combining electrospinning and phase separation methods for supercapacitor

Microporous carbon nanofibers (MCNFs) derived from polyacrylonitrile nanofibers were fabricated via electrospinning technology and phase separation in the presence of polyvinylpyrrolidone (PVP). PVP together with a mixed solvent of N, N-Dimethylformamide and dimethyl sulfoxide was used as pore forming agent. The influences of PVP content in casting solution on the structure and electrochemical performance of the MCNFs were also investigated. The highest capacitance of 200 F/g was obtained on a three-electrode system at a scan rate of 0.5 A/g. The good performance was owing to the high specific surface area and the large amount of micro-pores, which enhanced the absorption and the transportation efficiency of electrolyte ion during charge/discharge process. This research indicated that the combination of electrospinning and phase separation technology could be used to fabricate microporous carbon nanofibers as electrode materials for supercapacitors with high specific surface area and outstanding electrochemical performance. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.

FRACTAL BEHAVIOR OF DEVELOPMENT OF PHASE SEPARATION AND CRYSTALLIZATION IN BLENDS OF NYLON-6 WITH SODIUM SALT OF ETHYLENE /METHACRYLIC ACID COPOLYMER

Phase separation was studied by the optical microscopy in blends of nylon 6 (PA6) with sodium salt of ethylene/methacrylic acid copolymer (PEMA).The image collecting technology was used to keep track of the development of blends at a certain temperature.The fractal dimension of phase separation was calculated by the image solving technology according to the fractal theory and the self similarity behavior of the process was proved.The relationship of the fractal behavior with composition and experimental temperature was discussed.The fractal behavior of the crystallization development of the crystal phase of PA6 in blends was also discussed and the fractal behavior calculated.

PREPARATION OF MICROPOROUS ULTRA HIGH MOLECULAR WEIGHT POLYETHYLENE (UHMWPE) BY THERMALLY INDUCED PHASE SEPARATION OF A UHMWPE/LIQUID PARAFFIN MIXTURE

Ultra-high molecular weight polyethylene (UHMWPE) with a microporous structure was prepared via thermally induced phase separation (TIPS).Liquid paraffin (LP) was used as a diluent in the preparation of microporous UHMWPE. Small angle laser light scattering (SALLS) and differential scanning calorimetry (DSC) were used to determine the phase separation temperatures,i.e.the cloud points and the dynamic crystallization temperatures,respectively.It was found that the cloudI points were coincident with the cryst...

Dynamic scaling behaviour of late-stage phase separation in Ni75AlxV25-x alloys

The dynamic scaling behaviour of late-stage phase separation and coarsening mechanisms of L12 and D022 in Ni75AlxV25-x （3 ≤ x ≤ 10, at.%） alloys are studied using the microscopic phase-field dynamic model. The microelaso ticity field is incorporated into the diffusion dynamic model. The results show the morphology and coarsening dynamics being greatly changed by the elastic interactions among different precipitates, the particles aligning along the dominant directions, the average domain size （ADS） of L12 and D022 deviating from the exponent of temporal power-law, and the growth slowing down due to the increasing of elastic interactions. The dynamic scaling regime of late-stage coarsening of the precipitates is attained. Thus the scaling behaviour of structure function is also applicable for elastic interaction systems. It is also found that the variations of ADS and scaling function depend on the volume fraction of precipitates.

METASTABLE PHASE SEPARATION OF Fe_(50)Cu_(50) HYPOPERITECTIC ALLOY UNDER SPACE SIMULATION CONDITIONS

A 3m drop-tube was used to investigate the solidification of Fe50Cu50 hypoperitectic alloy. The falling droplets solidified as spheres and splats. The obtained particles range from 1000μm to 80μm in diameter. It was found that the phase separation occurred if the Fe-Cu liquid was undercooled to a certain extent before solidification.In the big particles macroscopic separation of Fe-rich phase always appeared in the cented of the particles, and in the small ones the Fe-rich phase usually solidified as little spheres. In the flakes the Fe-rich and Cu-rich layers alternatively displayed from top to bottom.

Effects of F127 on Properties of PVB/F127 Blend Hollow Fiber Membrane via Thermally Induced Phase Separation

Hydrophilic poly(vinyl butyral)(PVB) /Pluronic F127(F127) blend hollow fiber membranes were prepared via thermally induced phase separation(TIPS) ,and the effects of blend composition on the performance of hydrophilic PVB/F127 blend hollow fiber membrane were investigated.The addition of F127 to PVB/polyethylene glycol(PEG) system decreases the cloud point temperature,while the cloud point temperature increases slightly with the addition of F127 to 20%(by mass) PVB/F127/PEG200 system when the concentration of F127 is not higher than 5%(by mass) .Light scattering results show that the initial inter-phase periodic distance formed from the phase separation of 20%(by mass) PVB/F127/PEG200 system decreases with the addition of F127,so does the growth rate during cooling process.The blend hollow fiber membrane prepared at air-gap 5mm,of which the water permeability increases and the rejection changes little with the increase of F127 concentration.For the membrane prepared at zero air-gap,both water permeability and rejection of the PVB/F127 blend membrane are greater than those of PVB membrane,while the tensile strength changes little.Elementary analysis shows that most F127 in the polymer solution can firmly exist in the polymer matrix,increasing the hydrophilicity of the blend membrane prepared at air-gap of 5mm.

Liquid phase separation and subsequent dendritic solidification of ternary Fe_(35)Cu_(35)Si_(30) alloy

Liquid Fe35Cu35Si30alloy has achievedthemaximum undercooling of 328 K （0.24TL） with glass fluxing method, and it displayed triple solidification mechanisms. A critical undercooling of 24 K was determined for metastable liquid phase separation. At lower undercoolings,α-Fe phase was the primary phase and the solidification microstructure appeared as homogeneous well-defined dendrites. When the undercooling exceeded 24 K, the sample segregated into Fe-rich and Cu-rich zones. In the Fe-rich zone, FeSi intermetallic compound was the primary phase within the undercooling regime below 230 K, while Fe5Si3intermetallic compound replaced FeSi phase as the primary phase at larger undercoolings. The growth velocity of FeSi phase increased whereas that ofFe5Si3 phase decreased with increasing undercooling. For the Cu-rich zone, FeSi intermetallic compound was always the primary phase. Energy-dispersive spectrometry analyses showed that the average compositions of separated zones have deviated substantially from the original alloycomposition.