Zinc phosphating of 6061-Al alloy using REN as additive

Zinc phosphate coating formed on 6061-A1 alloy was studied with the help of electrochemical measurements, Fourier Transform Infrared （FTIR）, and Scanning Electron Microscopy （SEM）, after dipping it in phosphating solutions containing different concentrations of Rare Earth Nitrate （REN）. REN, which acted as an accelerator in the phosphating solution, could catalyze the surface reaction and accelerate the phosphating process. REN mainly enabled the P in the phosphate coating to exist in the form of PO4^3- and promoted the hydrolysis of phosphatic acid in a liquid layer at the cathodes. This resulted in the evolution of H2 at the cathodes, which increased the local pH value and in turn drove the precipitation of the phosphate coating. Additionally, REN was adsorbed on the surface of the aluminum substrates to form a gel during the phosphating process. These gel particles were good crystal seeds, which helped to form phosphate crystal nuclei and possess the function of a nucleation agent that could decrease the phosphate crystal size. The corrosion resistance of the formed zinc phosphate coatings was improved.

Composition and Performance of the Composite Coatings Obtained by Phosphating and Cerium Nitrate Post-Sealing on Galvanized Steel

To improve the corrosion resistance of phosphate coatings, the phosphated hot-dip galvanized (HDG) steel was post-sealed with cerium nitrate solution. The morphology, composition, corrosion resistance of the coatings was investigated by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and neutral salt spray (NSS) tests. The results show that after post-sealing the phosphated HDG samples with cerium nitrate solution, the pores among the zinc phosphate crystals are sealed by the compounds containing phosphorus, oxygen and cerium; the zinc phosphate crystals are covered by the flocculent cerium compounds; and the continuous composite coatings are formed on HDG steel. The corrosion resistance of the composite coatings, which increases with the increase in phosphating time and cerium nitrate post-sealing time, is far higher than that of the single phosphate coatings. The composite coatings with the optimal corrosion resistance are obtained for phosphating 300 s and post-sealing 300 s; and the corrosion resistance is more outstanding than that of the chromate coatings.

Self-healing Performance of Composite Coatings Prepared by Phosphating and Cerium Nitrate Post-sealing

The phosphated and cerium nitrate post-sealed galvanized steel was firstly scratched to expose zinc layer and then placed in neutral salt spray （NSS） chamber for different durations. The microstructure and compositions of the scratches were investigated using SEM and EDS. The phases of the corrosion products were examined through XRD. The self-healing mechanism of the composite coatings was discussed. The experimental results show that the composite coatings have an excellent corrosion resistance. The corrosion products increase with corrosion time and finally cover the whole scratch. They contain phosphorous, cerium, oxygen, chloride and zinc, and are fine needle and exceedingly compact. The composite coatings are favorable self-healing. During corrosion, the self-healing ions such as Ce3＋, Ce4＋, PO43-, Zn2＋ in the composite coatings were dissolved, migrated, recombined, and covered the exposed zinc, impeding zinc corrosion. The self-healing process of the scratches on the composite coatings can be divided into three stages, about 2 h, 4 h, and 24 h, respectively.

Study on phosphating treatment of aluminum alloy:role of yttrium oxide

Zinc phosphate coatings formed on 6061-Al alloy, after dipping in phosphating solutions containing different amounts of Y2O3（yttrium oxide）, were studied by scanning electron microscopy （SEM）, X-ray diffraction （XRD） and electrochemical measurements. Significant variations in the morphology and corrosion resistance afforded by zinc phosphate coating were especially observed as Y2O3 in phosphating solution varied from 0 to 40 mg/L. The addition of Y2O3 changed the initial potential of the interface between aluminum alloy substrate and phosphating solution and increased the number of nucleation sites. The phosphate coating thereby was less porous structure and covered the surface of aluminum alloy completely within short phosphating time. Phosphate coating was mainly composed of Zn3（PO4）2·4H2O （hopeite） and AlPO4（aluminum phosphate）. Y2O3, as an additive of phosphatization, accelerated precipitation and refined the gain size of phosphate coating. The corrosion resistance of zinc phosphate coating in 3% NaCl solution was improved as shown by polarization measurement. In the present research, the optimal amount of Y2O3 was 10-20 mg/L, and the optimal phosphating time was 600 s.

Novel interface engineering of LDH-based materials on Mg alloy for efficient photocatalytic systems considering the geometrical linearity of condensed phosphates

This study presents a facile and rapid method for synthesizing novel Layered Double Hydroxide(LDH)nanoflakes,exploring their application as a photocatalyst,and investigating the influence of condensed phosphates'geometric linearity on their photocatalytic properties.Herein,the Mg O film,obtained by plasma electrolysis of AZ31 Mg alloys,was modified by growing an LDH film,which was further functionalized using cyclic sodium hexametaphosphate(CP)and linear sodium tripolyphosphate(LP).CP acted as an enhancer for flake spacing within the LDH structure,while LP changed flake dispersion and orientation.Consequently,CP@LDH demonstrated exceptional efficiency in heterogeneous photocatalysis,effectively degrading organic dyes like Methylene blue(MB),Congo red(CR),and Methyl orange(MO).The unique cyclic structure of CP likely enhances surface reactions and improves the catalyst's interaction with dye molecules.Furthermore,the condensed phosphate structure contributes to a higher surface area and reactivity in CP@LDH,leading to its superior photocatalytic performance compared to LP@LDH.Specifically,LP@LDH demonstrated notable degradation efficiencies of 93.02%,92.89%,and 88.81%for MB,MO,and CR respectively,over a 40 min duration.The highest degradation efficiencies were observed in the case of the CP@LDH sample,reporting 99.99%for MB,98.88%for CR,and 99.70%for MO.This underscores the potential of CP@LDH as a highly effective photocatalyst for organic dye degradation,offering promising prospects for environmental remediation and water detoxification applications.

Study on Phosphating by Ultrasonic Wave at Room Temperature for Sintered NdFeB Magnet

The corrosion behavior of a NdFeB magnet obtained at room temperature,with and without ultrasonic were investigated.The corrosion resistance was investigated by corrosion immersion tests in 3 wt%neutral NaCl solutions,potentiodynamic polarization tests and electrochemical impedance spectroscopy(EIS).The morphology of the conversion coatings on NdFeB surface were analyzed by scanning electron microscopy(SEM).And the forming mechanism of coatings was studied by potential-time curves.The tests of corrosion resistances show that the combination of phosphating treatment with ultrasonic will further improve the corrosion resistance of the NdFeB.The SEM also confirms that phosphating coating under ultrasonic is more homogeneous and compact.

Phosphating-induced charge transfer on CoO/CoP interface for alkaline H_(2)evolution

Designing non-noble metal electrocatalysts toward alkaline hydrogen evolution reaction(HER)with high performance at a large current density is urgent.Herein,a CoO/CoP heterostructure catalyst(termed POZ)was designed by a phosphating strategy.The strong electron transfer on the interface of CoO/CoP was experimentally and theoretically proven.POZ showed a low overpotential of 236 mV at 400 mA/cm^(2),which was 249 mV lower than non-phosphated sample.It also exhibited a remarkable solar-to-hydrogen conversion efficiency of 10.5%.In this work,the construction of CoO/CoP interface realized by a simple phosphating strategy could provide an important reference to boost the HER performance on those materials not merely metal oxides.

Efficient Removal of Phosphate from Aqueous Solutions Using Corundum-hollow-spheres Supported Caclined Hydrotalcite Porous Thin Films

Phosphate was removed from aqueous environment by corundum-hollow-spheres supported caclined hydrotalcite (cHT) thin films. Mg-Al-CO3 hydrotalcite (HT) thin films were deposited on corundumhollow-sphere substrates by hydrothermal homogeneous precipitation at 120℃for 30-240 min and cHT thin films were obtained by annealing of the HT thin films at 500℃for 180 min. Their crystal phase, morphology and microstructure were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM).The results show that homogeneous, well-crystallized and hierarchical flower-like thin films were deposited firmly on the surface of the corundum. The mechanism of nucleation and growth of the HT thin films was fitted well with the anion coordination polyhedron growth unit model. To determine the absorption of phosphate by this adsorbent, different bed depth (10-30 cm) and flow rate (1.0-3.0 m L/min) were examined by column experiments. The highest removal efficiency of phosphate amounted to 98.5%under optimum condition (pH=7.2). The adsorption capacity increased as the bed depth increased and decreased as the flow rate increased.

Effect of Fluoride on the Ion-association of Calcium Phosphate and Crystallization of Hydroxyapatite

Using a titration setup to accurately control the reaction conditions and in situ monitor the reaction,we showed that fluoride exhibited negligible effects on the ion association process of calcium and phosphate and the formation of ACP nanospheres in a buffer solution with constant ionic strength.However,the stability of ACP increased with increasing fluoride concentration,which was ascribed to the inhibitory effect of fluoride on the aggregation of ACP nanospheres and the nucleation of nanocrystals on the surface of ACP nanospheres.Furthermore,fluoride could inhibit the lateral growth of HAP nanosheets and promote the formation of rod-like crystals.These results further improve our understanding of the crystallization pathway of HAP crystals and the regulatory effects of fluoride.

Enhancing sustainability in phosphate ore processing:Performance of frying oil as alternative flotation collector for carbonate removal

Recycling waste frying oils for the synthesis of flotation reagents presents a promising avenue for sustainable waste management.Moreover,it offers a cost-effective solution for crafting a specialized collector designed to efficiently remove carbonates and enhance phosphate enrichment in froth flotation processes.This study focuses on the synthesis of an anionic collector using the saponification reaction of a frying oil sample,subsequently applied to the flotation of calcite and dolomite.To elucidate the adsorption mechanisms of the frying oil collector(FrOC)and sodium oleate,a reference collector,on fluorapatite,calcite,dolomite,and quartz surfaces,comprehensive experiments were conducted,including zeta potential measurements and Fourier transform infrared spectroscopy.Results revealed diverse adsorption affinities of the molecules towards these minerals.To assess the practical performance of the collector,flotation tests were conducted using a natural phosphate ore mixture,employing a BoxBehnken experimental design.Notably,under optimized conditions(pH 9,1000 g/t of FrOC,3.5 min of conditioning,and 6 min of flotation),FrOC exhibited excellent performance,with calcite and dolomite recoveries exceeding 80%,while apatite recovery in the concentrate fraction remained below 10%.This work exemplifies both circular economy practices and the distinctive approach to sustainable mineral processing.

In-situ construction of abundant active centers on hierarchically porous carbon electrode toward high-performance phosphate electrosorption: Synergistic effect of electric field and capture sites

Phosphate removal is crucial for eutrophication control and water quality improvement.Electro-assisted adsorption,an eco-friendly elec-trosorption process,exhibited a promising potential for wastewater treatment.However,there are few works focused on phosphate electro-sorption,and reported electrodes cannot attach satisfactory removal capacities and rates.Herein,electro-assisted adsorption of phosphate via in-situ construction of La active centers on hierarchically porous carbon(LaPC)has been originally demonstrated.The resulted LaPC composite not only possessed a hierarchically porous structure with uniformly dispersed La active sites,but also provided good conductivity for interfacial electron transfer.The LaPC electrode achieved an ultrahigh phosphate electrosorption capability of 462.01 mg g^(-1) at 1 V,outperforming most existing electrodes.The superior phosphate removal performance originates from abundant active centers formed by the coupling of electricfield and capture sites.Besides,the stability and selectivity toward phosphate capture were maintained well even under comprehensive conditions.Moreover,a series of kinetics and isotherms models were employed to validate the electrosorption process.This work demonstrates a deep understanding and promotes a new level of phosphate electrosorption.

Upcycling the spent graphite/LiCoO_(2) batteries for high-voltage graphite/LiCoPO_(4)-co-workable dual-ion batteries

The worldwide proliferation of portable electronics has resulted in a dramatic increase in the number of spent lithium-ion batteries(LIBs).However,traditional recycling methods still have limitations because of such huge amounts of spent LIBs.Therefore,we proposed an ecofriendly and sustainable double recycling strategy to concurrently reuse the cathode(LiCoO_(2))and anode(graphite)materials of spent LIBs and recycled LiCoPO_(4)/graphite(RLCPG)in Li^(+)/PF^(-)_(6) co-de/intercalation dual-ion batteries.The recycle-derived dualion batteries of Li/RLCPG show impressive electrochemical performance,with an appropriate discharge capacity of 86.2 mAh·g^(-1) at25 mA·g^(-1) and 69%capacity retention after 400 cycles.Dual recycling of the cathode and anode from spent LIBs avoids wastage of resources and yields cathode materials with excellent performance,thereby offering an ecofriendly and sustainable way to design novel secondary batteries.

Differential roles of C-3 and C-6 phosphate monoesters in affecting potato starch properties

The effects of starch phosphate monoester content(SPC),namely C-3(C3P)and C-6 phosphate monoesters(C6P),on the starch properties were investigated using four potato starches with varied SPC/C3P/C6P and two nonphosphorylated maize starches with a similar range of amylose content(AC)as controls.The starch property results showed that a higher SPC is associated with lower turbidity,storage and loss modulus after storage,and water solubility,but higher swelling power(SP)and pasting viscosities.These findings suggested that SPC inhibited molecular rearrangement during storage and starch leaching during heating,and enhanced swelling and viscosities due to increased hydration and water uptake caused by the repulsion effect of phosphate groups and a less ordered crystalline structure.Increased SPC also resulted in lower resistant starch(RS)content in a native granular state but higher RS after retrogradation.Pearson correlations further indicated that SPC/C3P/C6P were positively correlated with peak(r^(2)=0.925,0.873 and 0.930,respectively),trough(r^(2)=0.994,0.968 and 0.988,respectively),and final viscosities(r^(2)=0.981,0.968 and 0.971,respectively).Notably,SPC,mainly C3P,exhibited a significantly positive correlation with SP(r^(2)=0.859)and setback viscosity(r^(2)=0.867),whereas SPC,mainly C6P,showed a weak positive correlation with RS after retrogradation(r^(2)=0.746).However,SPC had no significant correlations with water solubility,turbidity and rheology properties,which were more correlated with AC.These findings are helpful for the food industry to select potato starches with desired properties based on their contents of SPC,C3P,or C6P.

Solid-state impedance spectroscopy studies of dielectric properties and relaxation processes in Na_(2)O–V_(2)O_(5)–Nb_(2)O_(5)–P_(2)O_(5) glass

Solid-state impedance spectroscopy(SS-IS)was used to investigate the influence of structural modifications resulting from the addition of Nb2O5 on the dielectric properties and relaxation processes in the quaternary mixed glass former(MGF)system 35Na_(2)O–10V_(2)O_(5)–(55-x)P_(2)O_(5)–xNb_(2)O_(5)(x=0–40,mol%).The dielectric parameters,including the dielectric strength and dielectric loss,are determined from the frequency and temperature-dependent complex permittivity data,revealing a significant dependence on the Nb2O5 content.The transition from a predominantly phosphate glass network(x<10,region I)to a mixed niobate–phosphate glass net-work(10≤x≤20,region II)leads to an increase in the dielectric parameters,which correlates with the observed trend in the direct-cur-rent(DC)conductivity.In the predominantly niobate network(x≥25,region III),the highly polarizable nature of Nb5+ions leads to a fur-ther increase in the dielectric permittivity and dielectric strength.This is particularly evident in Nb-40 glass-ceramic,which contains Na_(13)Nb_(35)O_(94) crystalline phase with a tungsten bronze structure and exhibits the highest dielectric permittivity of 61.81 and the lowest loss factor of 0.032 at 303 K and 10 kHz.The relaxation studies,analyzed through modulus formalism and complex impedance data,show that DC conductivity and relaxation processes are governed by the same mechanism,attributed to ionic conductivity.In contrast to glasses with a single peak in frequency dependence of imaginary part of electrical modulus,M″(ω),Nb-40 glass-ceramic exhibits two distinct contributions with similar relaxation times.The high-frequency peak indicates bulk ionic conductivity,while the additional low-fre-quency peak is associated with the grain boundary effect,confirmed by the electrical equivalent circuit(EEC)modelling.The scaling characteristics of permittivity and conductivity spectra,along with the electrical modulus,validate time-temperature superposition and demonstrate a strong correlation with composition and modification of the glass structure upon Nb_(2)O_(5) incorporation.

Preparation and Reinforcement Adaptability of Jute Fiber Reinforced Magnesium Phosphate Cement Based Composite Materials

To improve the brittleness characteristics of magnesium phosphate cement-based materials(MPC)and to promote its promotion and application in the field of structural reinforcement and repair,this study aimed to increase the toughness of MPC by adding jute fiber,explore the effects of different amounts of jute fiber on the working and mechanical properties of MPC,and prepare jute fiber reinforced magnesium phosphate cement-based materials(JFRMPC)to reinforce damaged beams.The improvement effect of beam performance before and after reinforcement was compared,and the strengthening and toughening mechanisms of jute fiber on MPC were explored through microscopic analysis.The experimental results show that,as the content of jute fiber(JF)increases,the fluidity and setting time of MPC decrease continuously;When the content of jute fiber is 0.8%,the compressive strength,flexural strength,and bonding strength of MPC at 28 days reach their maximum values,which are increased by 18.0%,20.5%,and 22.6%compared to those of M0,respectively.The beam strengthened with JFRMPC can withstand greater deformation,with a deflection of 2.3 times that of the unreinforced beam at failure.The strain of the steel bar is greatly reduced,and the initial crack and failure loads of the reinforced beam are increased by 192.1%and 16.1%,respectively,compared to those of the unreinforced beam.The JF added to the MPC matrix dissipates energy through tensile fracture and debonding pull-out,slowing down stress concentration and inhibiting the free development of cracks in the matrix,enabling JFRMPC to exhibit higher strength and better toughness.The JF does not cause the hydration of MPC to generate new compounds but reduces the amount of hydration products generated.

Nicotinamide adenine dinucleotide phosphate oxidase in pancreatic diseases:Mechanisms and future perspectives

Pancreatitis and pancreatic cancer(PC)stand as the most worrisome ailments affecting the pancreas.Researchers have dedicated efforts to unraveling the mechanisms underlying these diseases,yet their true nature continues to elude their grasp.Within this realm,oxidative stress is often believed to play a causal and contributory role in the development of pancreatitis and PC.Excessive accumulation of reactive oxygen species(ROS)can cause oxidative stress,and the key enzyme responsible for inducing ROS production in cells is nicotinamide adenine dinucleotide phosphate hydrogen oxides(NOX).NOX contribute to pancreatic fibrosis and inflammation by generating ROS that injure acinar cells,activate pancreatic stellate cells,and mediate macrophage polarization.Excessive ROS production occurs during malignant transformation and pancreatic carcinogenesis,creating an oxidative microenvironment that can cause abnormal apoptosis,epithelial to mesenchymal transition and genomic instability.Therefore,understanding the role of NOX in pancreatic diseases contributes to a more in-depth exploration of the exact pathogenesis of these diseases.In this review,we aim to summarize the potential roles of NOX and its mechanism in pancreatic disorders,aiming to provide novel insights into understanding the mechanisms underlying these diseases.

Effect of safety valve types on the gas venting behavior and thermal runaway hazard severity of large-format prismatic lithium iron phosphate batteries

The safety valve is an important component to ensure the safe operation of lithium-ion batteries(LIBs).However,the effect of safety valve type on the thermal runaway(TR)and gas venting behavior of LIBs,as well as the TR hazard severity of LIBs,are not known.In this paper,the TR and gas venting behavior of three 100 A h lithium iron phosphate(LFP)batteries with different safety valves are investigated under overheating.Compared to previous studies,the main contribution of this work is in studying and evaluating the effect of gas venting behavior and TR hazard severity of LFP batteries with three safety valve types.Two significant results are obtained:(Ⅰ)the safety valve type dominates over gas venting pressure of battery during safety venting,the maximum gas venting pressure of LFP batteries with a round safety valve is 3320 Pa,which is one order of magnitude higher than other batteries with oval or cavity safety valve;(Ⅱ)the LFP battery with oval safety valve has the lowest TR hazard as shown by the TR hazard assessment model based on gray-fuzzy analytic hierarchy process.This study reveals the effect of safety valve type on TR and gas venting,providing a clear direction for the safety valve design.

Investigating Load Regulation Characteristics of a Wind-PV-Coal Storage Multi-Power Generation System

There is a growing need to explore the potential of coal-fired power plants(CFPPs)to enhance the utilization rate of wind power(wind)and photovoltaic power(PV)in the green energy field.This study developed a load regulation model for a multi-power generation system comprising wind,PV,and coal energy storage using realworld data.The power supply process was divided into eight fundamental load regulation scenarios,elucidating the influence of each scenario on load regulation.Within the framework of the multi-power generation system with the wind(50 MW)and PV(50 MW)alongside a CFPP(330 MW),a lithium-iron phosphate energy storage system(LIPBESS)was integrated to improve the system’s load regulation flexibility.The energy storage operation strategy was formulated based on the charging and discharging priority of the LIPBESS for each basic scenario and the charging and discharging load calculation method of LIPBESS auxiliary regulation.Through optimization using the particle swarm algorithm,the optimal capacity of LIPBESS was determined to be within the 5.24-4.88 MWh range.From an economic perspective,the LIPBESS operating with CFPP as the regulating power source was 49.1% lower in capacity compared to the renewable energy-based storage mode.

NOX4 promotes tumor progression through the MAPK-MEK1/2-ERK1/2 axis in colorectal cancer

BACKGROUND Metabolic reprogramming plays a key role in cancer progression and clinical outcomes;however,the patterns and primary regulators of metabolic reprogramming in colorectal cancer(CRC)are not well understood.AIM To explore the role of nicotinamide adenine dinucleotide phosphate oxidase 4(NOX4)in promoting progression of CRC.METHODS We evaluated the expression and function of dysregulated and survival-related metabolic genes using Gene Ontology and Kyoto Encyclopedia of Genes and Genomes.Consensus clustering was used to cluster CRC based on dysregulated metabolic genes.A prediction model was constructed based on survival-related metabolic genes.Sphere formation,migration,invasion,proliferation,apoptosis and clone formation was used to evaluate the biological function of NOX4 in CRC.mRNA sequencing was utilized to explore the alterations of gene expression NOX4 over-expression tumor cells.In vivo subcutaneous and lung metastasis mouse tumor model was used to explore the effect of NOX4 on tumor growth.RESULTS We comprehensively analyzed 3341 metabolic genes in CRC and identified three clusters based on dysregulated metabolic genes.Among these genes,NOX4 was highly expressed in tumor tissues and correlated with worse survival.In vitro,NOX4 overexpression induced clone formation,migration,invasion,and stemness in CRC cells.Furthermore,RNA-sequencing analysis revealed that NOX4 overexpression activated the mitogen-activated protein kinase-MEK1/2-ERK1/2 signaling pathway.Trametinib,a MEK1/2 inhibitor,abolished the NOX4-mediated tumor progression.In vivo,NOX4 overexpression promoted subcutaneous tumor growth and lung metastasis,whereas trametinib treatment can reversed the metastasis.CONCLUSION Our study comprehensively analyzed metabolic gene expression and highlighted the importance of NOX4 in promoting CRC metastasis,suggesting that trametinib could be a potential therapeutic drugs of CRC clinical therapy targeting NOX4.

Effects of Inoculation with Phosphate Solubilizing Bacteria on the Physiology,Biochemistry,and Expression of Genes Related to the Protective Enzyme System of Fritillaria taipaiensis P.Y.Li

Fritillaria taipaiensis P.Y.Li is a widely used medicinal herb in treating pulmonary diseases.In recent years,its wild resources have become scarce,and the demand for efficient artificial cultivation has significantly increased.This article is the first to apply phosphate solubilizing bacteria isolated from the rhizosphere soil of F.taipaiensis P.Y.Li to the cultivation process of F.taipaiensis P.Y.Li.The aim is to identify suitable reference strains for the artificial cultivation and industrial development of F.taipaiensis P.Y.Li by examining the effects of various phosphate solubilizing bacteria and their combinations on photosynthesis,physiological and biochemical properties,and gene expression related to the protective enzyme system in F.taipaiensis P.Y.Li.The experiment,conducted in pots at room temperature,included a control group(CK)and groups inoculated with inorganic phosphorussolubilizing bacteria:W1(Bacillus cereus),W2(Serratia plymuthica),W12(Bacillus cereus and Serratia plymuthica),and groups inoculated with organophosphorus-solubilizing bacteria:Y1(Bacillus cereus),Y2(Bacillus cereus),Y12(Bacillus cereus and Bacillus cereus),totaling seven groups.Compared to CK,most growth indices in the bacterial addition groups showed significant differences,with W12 achieving the highest values in all indices except the leaf area index.The content of photosynthetic pigments,photosynthetic parameters,and osmoregulatory substances increased variably in each bacterial treatment group.W12 exhibited the highest content of chlorophyll a and soluble protein,while W1 had the highest free proline content.The activities of peroxidase(POD),superoxide dismutase(SOD),and catalase(CAT)in all inoculated groups were higher than in CK,with significant changes in SOD and CAT activities.The malondialdehyde(MDA)content in all inoculated groups was lower than in CK,with Y12 being the lowest,at approximately 30%of CK.Gene expression corresponding to these three enzymes also increased variably,with POD expression in Y2 being the highest at 2.73 times that of CK.SOD and CAT expression in Y12 were the highest,at 1.84 and 4.39 times that of CK,respectively.These results indicate that inoculating phosphate solubilizing bacteria can enhance the growth of F.taipaiensis P.Y.Li,with the mixed inoculation groups W12 and Y12 demonstrating superior effects.This lays a theoretical foundation for selecting bacterial fertilizers in the cultivation process of F.taipaiensis P.Y.Li.