A Hybrid Compensation Scheme for the Input Rate-Dependent Hysteresis of the Piezoelectric Ceramic Actuators

A hybrid compensation scheme for piezoelectric ceramic actuators(PEAs)is proposed.In the hybrid compensation scheme,the input rate-dependent hysteresis characteristics of the PEAs are compensated.The feedforward controller is a novel input rate-dependent neural network hysteresis inverse model,while the feedback controller is a proportion integration differentiation(PID)controller.In the proposed inverse model,an input ratedependent auxiliary inverse operator(RAIO)and output of the hysteresis construct the expanded input space(EIS)of the inverse model which transforms the hysteresis inverse with multi-valued mapping into single-valued mapping,and the wiping-out,rate-dependent and continuous properties of the RAIO are analyzed in theories.Based on the EIS method,a hysteresis neural network inverse model,namely the dynamic back propagation neural network(DBPNN)model,is established.Moreover,a hybrid compensation scheme for the PEAs is designed to compensate for the hysteresis.Finally,the proposed method,the conventional PID controller and the hybrid controller with the modified input rate-dependent Prandtl-Ishlinskii(MRPI)model are all applied in the experimental platform.Experimental results show that the proposed method has obvious superiorities in the performance of the system.

Importance of Three-Dimensional Piezoelectric Coupling Modeling in Quantitative Analysis of Piezoelectric Actuators

This paper demonstrates the importance of three-dimensional(3-D)piezoelectric coupling in the electromechanical behavior of piezoelectric devices using three-dimensional finite element analyses based on weak and strong coupling models for a thin cantilevered piezoelectric bimorph actuator.It is found that there is a significant difference between the strong and weak coupling solutions given by coupling direct and inverse piezoelectric effects(i.e.,piezoelectric coupling effect).In addition,there is significant longitudinal bending caused by the constraint of the inverse piezoelectric effect in the width direction at the fixed end(i.e.,3-D effect).Hence,modeling of these effects or 3-D piezoelectric coupling modeling is an electromechanical basis for the piezoelectric devices,which contributes to the accurate prediction of their behavior.

Enhancing Stress Intensity Factor Reduction in Cracks Originating from a Circular Hole in a Rectangular Plate under Uniaxial Stress through Piezoelectric Actuation

Circular holes are commonly employed in engineering designs;however, they often serve as locations where cracks initiate and propagate. This paper explores a novel approach to structural repair by utilizing piezoelectric actuators. The primary focus of this study is to investigate the influence of an adhesively bonded piezoelectric actuator patch placed above a circular hole on the stress intensity factor (SIF) in an aluminium plate. The plate is subjected to uniaxial tensile stress, while the piezoelectric actuator is excited with varying voltage levels. The analysis is conducted using the finite element method (FEM), a powerful numerical technique for simulating complex structures. The study assesses the stress distribution and employs the SIF as an adequate criterion for evaluating the impact of different patch configurations. The results indicate a strong correlation between the applied voltage and the SIF. Whether the SIF increases or decreases depends on the polarization of the piezoelectric actuator. Particularly noteworthy is the finding that rectangular patches in a horizontal orientation significantly reduce the SIF compared to other patch geometries. Moreover, double-sided patches exhibit a pronounced decrease in the SIF compared to single-sided patches. In summary, this research underscores the potential of piezoelectric actuators in mitigating stress intensity in structures with circular hole with crack initiation. It offers valuable insights into the influence of applied voltage, patch geometry, and patch placement on the SIF, thereby contributing to developing effective strategies for enhancing structural integrity.

Micro-displacement amplifying mechanism driven by piezoelectric actuator

Piezoelectric actuator has high stiffness, high frequency and infinite control precision, but a short output displacement which is often 1/1 000 of its length. In order to meet the requirements that tools feeding should be long-travel, high-frequency and high-precision in non-circular precision turning, a new one-freedom flexure hinge structure is put forward to amplify the output displacement of piezoelectric actuator. Theoretical analysis is done on the static and dynamic characteristics of the structure, differential equations are presented, and it is also verified by the finite element method. It's proved by experiments that the output displacement of the structure is 293 μm and its resonant frequency is 312 Hz.

Voltage property analysis of piezoelectric floating mass actuator used in middle ear implant

Aiming at a kind of middle ear implant（MEI）, the driving voltage of a piezoelectric floating mass actuator is analyzed using a 0. 7Pb （Mg1/3Nb2/3） O3-0. 3PbTiO3 （ PMN- 30% PT）stack as a new type of vibrator. For the purpose of facilitating the analysis, a simplified coupling model of the ossicular chain and the piezoelectric actuator is constructed. First, a finite element model of a human middle ear is constructed by reverse engineering technology, and the validity of this model is confirmed by comparing the simulated motion of the stapes footplate obtained by this model with experimental measurements. Then the displacement impedance of the incus long process is analyzed, and a single mass-spring-damper equivalent model of the ossicular chain attached with the clamp is derived. Finally, a simplified coupling model of the ossicular chain and the piezoelectric actuator is established and used to analyze the driving voltage property of the actuator. The results show that the required driving voltage decreases with the increase in the frequency, and the maximum required driving voltage is 20. 9 V in the voice frequencies. However, in the mid-high frequencies where most sensorineural hearing loss occurs, the maximum required driving voltage is 3.8 V, which meets the low-voltage and low-power requirements of the MEI.

Nonlinear static characteristics of piezoelectric unimorph bending micro actuators

The nonlinear static characteristic of a piezoelectric unimorph cantilever micro actuator driven by a strong applied electric field is studied based on the couple stress theory.The cantilever actuator consists of a piezoelectric layer,a passive（elastic）layer and two electrode layers.First,the nonlinear static characteristic of the actuator caused by the electrostriction of the piezoelectric layer under a strong applied electric field is analyzed using the Rayleigh-Ritz method.Secondly,since the thickness of the cantilever beam is in micro scale and there exists a size effect,the size dependence of the deformation behavior is evaluated using the couple stress theory.The results show that the nonlinearities of the beam deflection increase along with the increase of the applied electric field which means that softening of the micro beam rigidity exists when a strong external electric field is applied.Meanwhile,the optimal value of the thickness ratio for the passive layer and the piezoelectric layer is not around 1.0 which is usually adopted by some previous researchers.Since there exists a size effect of the micro beam deflection,the optimal value of this thickness ratio should be greater than 1.0 in micro scale.

Design of Floating Mass Type Piezoelectric Actuator for Implantable Middle Ear Hearing Devices

To overcome some of the problems inherent in conventional heating aids such as low gain at high fi＇equencies due to acoustic feedback, discomfort in occlusion of the extemal ear canal and so on, implantable middle ear hearing devices （IMEHDs） have been developed over the past two decades. For such kinds of IMEHDs, this paper presents the design of a floating mass piezoelectric actuator using a PMN-30%PT stack as a new type of vibrator. The proposed piezoelectric actuator consists of only three components of a piezoelectric stack, a metal case and a clamp. For the purpose of aiding the design of this actuator, a coupling biomechanics model of human middle ear and the piezoelectric actuator was constructed. This model was built based on a complete set of computerized tomography section images of a healthy volunteer＇s left ear by reverse engineering technology. The validity of this model was confirmed by comparing the motion of the tympanic membrane and stapes footplate obtained by this model with published experimental measurements on human temporal bones. It is shown that the designed actuator can be implanted on the incus long process by a simple surgical operation, and the stapes footplate displacement by its excitation at 10.5 V root-mean-square（RMS） voltage was equivalent to that from acoustic stimulation at 100 dB sound pressure level（SPL）, which is adequate stimulation to the ossicular chain. The corresponding power consumption is 0.04 mW per volt of excitation at 1 kHz, which is low enough for the transducer to be used in an implantable middle ear device.

Improvement of Aircraft Rolling Power by Use of Piezoelectric Actuators

Piezoelectric actuators are distributed on both side of a rectangular wing model,and the possibility of improvement of aircraft rolling power is investigated. The difference between the model with aileron deflection and the model without aileron (fictitious control surface, FCS) is studied. The analytical results show that these two cases are substantial different. In aileron deflection case, the aeroelastic effect is disadvantageous, so the structural stiffness should be high until the electrical voltage is not necessary. But in the case of FCS,the aeroelastic effect is advantageous and it means that lower structural stiffness can lead to lower voltage. Compared with aileron project, the FCS project can save structure weight.

Modeling and Tracking Control for Piezoelectric Actuator Based on a New Asymmetric Hysteresis Model

This paper presents a new asymmetric hysteresis model and its application in the tracking control of piezoelectric actuators. The proposed model is based on a coupled-play operator which can avoid the conventional Prandtl-Ishlinskii(CPI)model's defects, i.e., the symmetric property. The high accuracy for modeling asymmetric hysteresis is validated by comparing simulation results with experimental measurements. In order to further evaluate the performance of the proposed model in closed-loop tracking application, two different hybrid control methods which experimentally demonstrate their performance under the same operating conditions, are compared to validate that the hybrid control strategy with proposed hysteresis model can mitigate the hysteresis more effectively and achieve better tracking precision. The experimental results demonstrate that the proposed modeling and tracking control strategy can realize efficient control of piezoelectric actuator.

Precise robust motion control of cell puncture mechanism driven by piezoelectric actuators with fractional-order nonsingular terminal slidingmode control

A novel robust controller is proposed in this study to realize the precise motion control of a cell puncture mechanism(CPM)driven by piezoelectric ceramics(PEAs).The entire dynamic model of CPM is constructed based on the Bouc–Wen model,and the nonlinear part of the dynamic model is optimized locally to facilitate the construction of a robust controller.A model-based,nonlinear robust controller is constructed using time-delay estimation(TDE)and fractional-order nonsingular terminal sliding mode(FONTSM).The proposed controller does not require prior knowledge of unknown disturbances due to its real-time online estimation and compensation of unknown terms by using the TDE technology.The controller also has finite-time convergence and high-precision trajectory tracking capabilities due to FONTSM manifold and fast terminal sliding mode-type reaching law.The stability of the closed-loop system is proved by Lyapunov stability theory.Computer simulation and hardware-in-loop simulation experiments of CPM verify that the proposed controller outperforms traditional terminal sliding mode controllers,such as the integer-order or model-free controller.The proposed controller can also continuously output without chattering and has high control accuracy.Zebrafish embryo is used as a verification target to complete the cell puncture experiment.From the engineering application perspective,the proposed control strategy can be effectively applied in a PEA-driven CPM.

Modeling and Design of H-Infinity Controller for Piezoelectric Actuator LIPCA

We proposed a dynamic model identification and design of an H-Infinity （i.e.H） controller using a LightweightPiezo-Composite Actuator （LIPCA）.A second-order dynamic model was obtained by using input and output data, and applyingan identification algorithm.The identified model coincides well with the real LIPCA.To reduce the resonating mode that istypical of piezoelectric actuators, a notch filter was used.A feedback controller using the Hcontrol scheme was designed basedon the identified dynamic model; thus, the LIPCA can be easily used as an actuator for biomemetic applications such as artificialmuscles or macro/micro positioning in bioengineering.The control algorithm was implemented using a microprocessor, analogfilters, and power amplifying drivers.Our simulation and experimental results demonstrate that the proposed control algorithmworks well in real environment, providing robust performance and stability with uncertain disturbances.

FLUTTER SUPPRESSION USING DISTRIBUTED PIEZOELECTRIC ACTUATORS

The Flutter suppression using distributed piezoelectric actuators has been analyzed and tested. In constructing the finite element equation, effects of piezoelectric matrices are investigated. LQG method is used in designing the control law. In reducing the order of the control law, both balance realization and LK methods are used. For the rational approximation of the unsteady aerodynamic forces LS method is improved. In determining the piezoelectric constants d31 a new dynamic response method is developed. Laser vibrameter is used to pick up the model response and in ground resonance test the model is excited by piezoelectric actuators. Reasonable agreement of the wind tunnel flutter suppression test with calculated results is obtained.

Compensation of hysteresis in piezoelectric actuator with iterative learning control

This paper presents the application of iterative learning control (ILC) to compensate hysteresis in a piezoelectric actuator. The proposed controller is a hybrid of proportional-integral-differential (PID) control, whose main function is for trajectory tracking, and a chatter-based ILC, whose main function is for hysteresis compensation. Stability analysis of the proposed ILC is presented, with the PID included in the dynamic of the piezoelectric actuator. The performance of the proposed controller is analysed through simulation and verified with experiment with a piezoelectric actuator.

Finite Element Analysis of Smart Structures with Piezoelectric Sensors/Actuators Including Debonding

In vibration active control of composite structures, piezoelectricsensors/actuators are usually bonded to the surface of a host structure. Debonding of piezoelectricsensors/actuators can result in significant changes to the static and dynamic response. In thepresent paper, an novel Enhanced Assumed Strain(EAS) piezoelectric solid element formulation isdeveloped for vibration active control of laminated structures bonded with piezoelectric sensors andactuators. Unlike the conventional brick elements, the present formulation is very reliable, moreaccurate, and computationally efficient and can be used to model the response of shell structuresbesides thin plates. Delaminations are modeled by pairs of nodes with the same coordinates butdifferent node numbers, and numerical results demonstrate the performance of the element and theglobal and local effects of debonding sensors/actuators on the dynamics of the adaptive laminates.

Active disturbance rejection control for precise position tracking of piezoelectric actuators

Positioning with high precision piezoelectric actuators is widely used.To overcome positioning inaccuracy caused by hysteresis and creep of actuators,a precise tracking method for piezoelectric actuators using active disturbance rejection control(ADRC) has been proposed in this paper.This method,in real-time,actively estimates and compensates parameter uncertainties,nonlinear factors such as hysteresis,and external disturbances in the tracking system.Precise tracking of the piezoelectric actuator can be achieved without any form of feedforward compensations.The experimental results demonstrate that the active disturbance rejection controller can reduce tracking errors by over90%comparing with those using the PID controller.Those features of the proposed control method are very suitable for applications in adaptive optics.

A refined finite element method for bending analysis of laminated plates integrated with piezoelectric fiber-reinforced composite actuators

This research presents a finite element formulation based on four-variable refined plate theory for bending analysis of cross-ply and angle-ply laminated composite plates integrated with a piezoelectric fiber-reinforced composite actuator under electromechanical loading. The four-variable refined plate theory is a simple and efficient higher-order shear deformation theory, which predicts parabolic variation of transverse shear stresses across the plate thickness and satisfies zero traction conditions on the plate free surfaces. The weak form of governing equations is derived using the principle of minimum potential energy, and a 4-node non-conforming rectangular plate element with 8 degrees of freedom per node is introduced for discretizing the domain. Several benchmark problems are solved by the developed MATLAB code and the obtained results are compared with those from exact and other numerical solutions, showing good agreement.

Active control of structural vibration by piezoelectric stack actuators

This paper presents a general analytical model of flexible isolation system for application to the installation of high-speed machines and lightweight structures. Piezoelectric stack actuators are employed in the model to achieve vibration control of flexible structures, and dynamic characteristics are also investigated. Mobility technique is used to derive the governing equations of the system. The power flow transmitted into the foundation is solved and considered as a cost function to achieve optimal control of vibration isolation. Some numerical simulations revealed that the analytical model is effective as piezoelectric stack actuators can achieve substantial vibration attenuation by selecting proper value of the input voltage.

NEW PRECISION PIEZOELECTRIC STEP ACTUATOR

A new precision piezoelectric actuator is proposed to improve its drive capabilities. The actuator is based on the piezoelectric technology. It adopts the principle of bionics and works with a new method of stator initiative anchoring/loosen and a distortion structure of double-side thin flexible hinge. It solves the problem of anchoring/loosen, frequency, journey, resolution and velocity. The experiment shows that the new linear piezoelectric actuator works with high frequency （100 Hz）, high speed （502 μm/s）, large travel （〉10 mm）, high resolution （0.05 μm） and high load （100 N）. This kind of new piezoelectric actuator will be applied for large travel and high resolution driving device, optics engineering precision positioning and some micromanipulation field.

Experimental Validation of Improving Aircraft Rolling Power Using Piezoelectric Actuators

Piezoelectric actuators are mounted on both sides of a rectangular wing model. Possibility of the improvement of aircraft rolling power is investigated. All experiment proiects, including designing the wind tunnel model, checking the material constants, measuring the natural frequencies and checking the effects of actuators, guarantee the correctness and precision of the finite element model. The wind tunnel experiment results show that the calculations coincide with the experiments. The feasibility of fictitious control surface is validated.

CuO added Pb_(0.92)Sr_(0.06)Ba_(0.02)(Mg_(1/3)Nb_(2/3))_(0.25)(Ti_(0.53)Zr_(0.47))_(0.75)O_3 ceramics sintered with Ag electrodes at 900℃ for multilayer piezoelectric actuator

CuO added Pb0.92Sr0.06Ba0.02（Mg1/3Nb2/3）0.25（Ti0.53Zr0.47）0.75O3 ceramics were studied to prepare high-quality multilayer piezoelectric actuators with pure Ag electrodes at 900 ℃. CuO addition not only reduced the sintering temperature significantly from 1260 ℃ to 900 ℃ but also improved the ceramic density to 7.742 g/cm3. The 0.7 wt.% CuO added ceramic sintered at 900 ℃ shows the remnant polarization （Pr） of 40 μC/cm2, 0.28% strain at 40 kV/cm, and the piezoelectric coefficient （d33） of 630 pC/N. This ceramic shows a strong relaxor characteristic with a Curie temperature of 200 ℃. Furthermore, the 0.7 wt.% CuO added ceramic and pure Ag electrodes were co-fired at 900 ℃ to prepare a high-quality multilayer piezoelectric actuator with a d33 of over 450 pC/N per ceramic layer.