Previous studies done elsewhere have shown that Eucalyptus poles treated with chromated copper arsenate (CCA) can last over 30 years. Kenya is exceptional because in some eco-regions, the Eucalyptus poles’ life span ...Previous studies done elsewhere have shown that Eucalyptus poles treated with chromated copper arsenate (CCA) can last over 30 years. Kenya is exceptional because in some eco-regions, the Eucalyptus poles’ life span has greatly reduced to 5 years. The current study was designed to evaluate wood deteriorating agents of CCA-treated Eucalyptus poles and variability in four eco-regions of Kenya, namely, dryland, coastal, highland and humid lake. A total of 360 Eucalyptus pole samples were used for this experiment. Three CCA treatments were used to treat transmission poles at 20 kg/cm3 fencing posts samples at 6 kg/cm3, and a control group. Results indicated that termites and wood-decay fungi attacks caused wood deterioration in the four eco-regions. The proportion of power transmission pole degradation by wood deteriorating agents varied across eco-regions, between treatments and control and between time after treatments. Dryland eco-regions had the highest termite-related degradation (41.82%) while wood-decay fungi attack was highest in the highland eco-regions (9.20%). Samples treated with 6 kg/cm3 recorded the lowest level of wood deterioration, manifested by minimal superficial termite and wood-decay fungi attack. Samples treated with 20 kg/cm3 were characterized by moderate termite and wood-decay fungi attacks observed around the heartwood region, unlike sapwood. This study concluded that the deterioration of Eucalyptus CCA-treated poles is a question of climatic variability and hence, to increase the poles’ lifespan, CCA treatment should be tailored according to the characteristics of the ecoregion of use. Further investigations will inform the diversity of termites and decay-fungi across different eco-regions.展开更多
Permanent magnet claw pole machine(PMCPM) is a special kind of transverse flux permanent magnet machine. Compared with other electrical machines, it has the advantages of high torque density and high efficiency for hi...Permanent magnet claw pole machine(PMCPM) is a special kind of transverse flux permanent magnet machine. Compared with other electrical machines, it has the advantages of high torque density and high efficiency for high speed operation. However, because of its complex irregular structure, the manufacturing process using silicon sheets is complicated. Soft magnetic composite material(SMC) is manufactured by powder metallurgy technology, which can produce various shapes of stator core structures, so it is easier to produce various irregular shapes of the stator core. However, the raw SMC material is relatively expensive, and the mechanical strength of SMC is weak. In this paper, a PMCPM with hybrid cores is proposed. With the adoption of hybrid silicon sheet-SMC cores and amorphous alloy-SMC cores, the torque ability of PMCPM can be improved greatly and it can have higher efficiency for more wide operation frequency. Meanwhile, its mechanical strength has been improved and it can be designed for high torque direct drive applications as it is a modular machine. Furthermore, three methods are proposed to reduce the additional eddy current loss which resulted from the employment of hybrid cores in PMCPM.展开更多
Objective:To evaluate the long-term stone-free rate(SFR)of retrograde intrarenal surgery(RIRS)in the treatment of lower pole renal calculi using only basket relocation and identify independent predictors of stone-free...Objective:To evaluate the long-term stone-free rate(SFR)of retrograde intrarenal surgery(RIRS)in the treatment of lower pole renal calculi using only basket relocation and identify independent predictors of stone-free status.Methods:All consecutive patients undergoing RIRS lower pole renal calculi at a single highvolume tertiary center were analyzed retrospectively.Lower pole stones were relocated to the upper pole,where laser lithotripsy was performed.All patients were followed up in the clinic following the surgery and yearly thereafter.The stone-free status was assessed with a combination of an abdominal ultrasound and abdominal X-ray,or an abdominal non-contrast computed tomography if the stones were known to be radiolucent.Results:A total of 480 consecutive patients who underwent RIRS for treatment of lower pole renal calculi,between January 2012 and December 2018,were analyzed from a prospectively maintained database of 3000 ureteroscopies.With a median follow-up time of 18.6 months,the mean SFR was 94.8%.The procedures were unsuccessful in 26(5.4%)patients due to unreachable stones.The median stone size of the unreachable stones was 12 mm(range 10e30 mm).Multivariable logistic regression analysis revealed two predictors of SFR for lower pole stones:a small cumulative stone burden(odds ratio[OR]:0.903,95%confidence interval[CI]:0.867e0.941,p<0.0001)and preoperative ureteral stent insertion(OR:0.515,95%CI:0.318e0.835,pZ0.007).Conclusion:The long-term SFR of RIRS for the treatment of lower pole stones with basket displacement with appropriate patient selection is high.展开更多
Soft magnetic composite(SMC)material is an ideal soft magnetic material employed for developing 3D magnetic flux electromagnetic equipment,due to its advantages of 3D magnetic isotropy characteristic,low eddy current ...Soft magnetic composite(SMC)material is an ideal soft magnetic material employed for developing 3D magnetic flux electromagnetic equipment,due to its advantages of 3D magnetic isotropy characteristic,low eddy current loss,and simple manufacturing process.The permanent magnet claw pole machine(PMCPM)with SMC cores is a good case that the SMC to be adopted for developing 3D flux electrical machines.In this paper,a novel axial-radial flux permanent magnet claw pole machine(ARPMCPM)with SMC cores and ferrite magnets is proposed.Compared with the traditional PMCPM,the proposed ARPMCPM is designed with only one spoke PM rotor and its whole structure is quite compact.For the performance prediction,the 3D finite element method(FEM)is used.Meanwhile,for the performance evaluation,a previously developed axial flux claw pole permanent magnet machine(AFCPM)is employed as the benchmark machine and all these machines are optimized by using the combined multilevel robust Taguchi method.It can be seen that the proposed ARPMCPM is with higher torque/weight density and operation efficiency.展开更多
The idea of research started with a crazy imaginary theory in the field of astrogeography, saying: We often taught ourselves and then convinced the students that the planet Earth moves despite not feeling the vibratio...The idea of research started with a crazy imaginary theory in the field of astrogeography, saying: We often taught ourselves and then convinced the students that the planet Earth moves despite not feeling the vibrations of traffic, and we listed successive scientific confirmations to indicate the rotation of the planet in a regular movement around its axis once every 24 hours, and it is running in another second movement around the sun once every 365¼ days, so are they only two movements, no more?! Is it possible for him to run at a regular speed in an additional direction?展开更多
The present work deals with reducing greenhouse gas emissions through improving the life span of wooden power electric poles of Eucalyptus saligna. Indeed, in Sub-Saharan African countries, Cameroon in particular, mos...The present work deals with reducing greenhouse gas emissions through improving the life span of wooden power electric poles of Eucalyptus saligna. Indeed, in Sub-Saharan African countries, Cameroon in particular, most of the power line networks are made of wooden supports and according to the Cameroon energy distribution company, wooden poles represent 32% of the causes of death linked to the state of the network. The company’s 2019 annual report indicates that 40,000 wooden poles were in critical condition and should be replaced. A significant number of mechanical failures affecting these supports have been observed. For example, on the HVA/LV power line “D17 Nko- abang” in Yaoundé in Cameroon, less than three years old, 10 (ten) cases of poles falling and/or breaking, due to their mechanical loading, were observed over a period of fewer than nine months, causing an average service stoppage for more than 11 hours and affecting an average of 3280 customers. These incidents lead to questions about how the supports are dimensioned and what load capacities they are designed to support. The aim of this work is, therefore, to suggest a method of dimensioning wooden poles hence reducing green- house gas emissions due to the deforestation by reducing the number of woo- den poles at risk to be replaced on Cameroon’s electricity distribution network. And more specifically, to reduce the number of mechanical failures affecting the wooden supports observed by analyzing the current wooden supports with their loads and to make proposals for improving the actual dimensioning me- thods. From the study carried out, it appears that 449 out of 845 supports, i.e., 53% needed to be replaced or monitored because they support the nominal forces ranging from 85% to 150% of their admissible limit and proposals have been made to improve their dimensioning.展开更多
The design, field quality optimization, multipole field analysis, and field measurement of a dipole for a newly developed superconducting proton cyclotron(SC200) beamline are presented in this paper. The maximum magne...The design, field quality optimization, multipole field analysis, and field measurement of a dipole for a newly developed superconducting proton cyclotron(SC200) beamline are presented in this paper. The maximum magnetic field of the dipole is 1.35 T; the bending radius is 1.6 m with a proton beam energy in the range of70–200 Me V. The magnetic field was calculated with 2 D and 3 D simulations, and measured with a Hall mapping system. The pole shim and end chamfer were optimized to improve the field quality. Based on the simulated results,the multipole field components in the good-field region were studied to evaluate the field quality. The results showed that the field quality is better than ± 5 × 10^(-4) at1.35 T with shimming and chamfering. For the transverse field homogeneity, the third-order(B3) and fifth-order(B5)components should be controlled with symmetrical shims.The second-order(B2) component was the main disturbance for the integral field homogeneity; it could be improved with an end chamfer. The magnet manufacturing and field measurement were performed in this project. The measurement results demonstrated that the magnetic design and field quality optimization of the 45° dipole magnet can achieve the desired high field quality and satisfy the physical requirements.展开更多
The soft switching operation principle and operation performance of rugged resonant pole (RRP) is given. The applications of RRP in soft switching DC DC converter and soft switching inverter are discussed in detail. R...The soft switching operation principle and operation performance of rugged resonant pole (RRP) is given. The applications of RRP in soft switching DC DC converter and soft switching inverter are discussed in detail. RRP can constitute buck boost soft switching DC DC converter and isolated soft switching DC DC converter with the automatic limitation performance of output power. Partial series resonant DC DC converter with RRP can realize the zero voltage/zero current switching of power devices. RR...展开更多
A Mach-Zehnder(MZ) electro-optic(EO) modulator are real iz ed,with three optical layers as polymer materials.The functional layer is the co rona poled crosslinkable polyurethane.The ridge waveguide is fabricated by us...A Mach-Zehnder(MZ) electro-optic(EO) modulator are real iz ed,with three optical layers as polymer materials.The functional layer is the co rona poled crosslinkable polyurethane.The ridge waveguide is fabricated by using the spin-coating,poling,photolithography and oxygen reactive ion etching(RIE) techniques.The mode and the modulation properties of these devices are demonstra ted in a micron control system,while the light source works at the wavelength of 1 31 or 1 55 micron.展开更多
Electrochemical machining (ECM) is one of the best al ternatives for producing complex shapes in advanced materials used in aircraft a nd aerospace industries. However, the reduction of the stray material removal co n...Electrochemical machining (ECM) is one of the best al ternatives for producing complex shapes in advanced materials used in aircraft a nd aerospace industries. However, the reduction of the stray material removal co ntinues to be major challenges for industries in addressing accuracy improvement . This study presents a method of improving machining accuracy in ECM by using a dual pole tool with a metallic bush outside the insulated coating of a cathode tool. The bush is connected with anode and so the electric field at the side gap area is substantially weakened. The modeling and simulation indicate that the p ositive bush brings down the current density at the side gap area of the machine d hole and hence reduces the stray material removal there. It has been experimen tally observed that the machining accuracy and the process stability are signifi cantly improved.展开更多
AIM To compare the outcomes of retrograde intrarenal surgery(RIRS) and miniaturized percutaneous nephrolithotomy(mini-PCNL) in treating lower pole(LP) renal stones with a diameter of 1.5-2.5 cm.METHODS A total of 216 ...AIM To compare the outcomes of retrograde intrarenal surgery(RIRS) and miniaturized percutaneous nephrolithotomy(mini-PCNL) in treating lower pole(LP) renal stones with a diameter of 1.5-2.5 cm.METHODS A total of 216 patients who underwent mini-PCNL(n = 103) or RIRS n = 113) for LP stones with a diameter of 1.5-2.5 cm were enrolled between December 2015 and April 2017 at the Urology Department of Ningbo Urology and Nephrology Hospital.RESULTS Significant differences were found in the hospital stay(9.39 ± 4.01 vs 14.08 ± 5.26, P < 0.0001) and hospitalization costs(2624.5 ± 513.36 vs 3255.2 ± 976.5, P < 0.0001) between the RIRS and mini-PCNL groups. The mean operation time was not significantly different between the RIRS group(56.48 ± 24.77) and the mini-PCNL group(60.04 ± 30.38, P = 0.345). The stone-free rates at the first postoperative day(RIRS vs mini-PCNL: 90.2% vs 93.2%, P = 0.822) and the second month postoperatively(RIRS vs mini-PCNL: 93.8% vs 95.1%, P = 0.986) were not significantly different.CONCLUSION RIRS and mini-PCNL are both safe and effective methods for treating LP stones with a diameter of 1.5-2.5 cm. RIRS can be considered as an alternative to PCNL for the treatment for LP stones of 1.5-2.5 cm.展开更多
This paper reports a continuous-wave (CW) mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate (PPLN) pumped by a diode-end-pumped CW Nd:YVO4 laser. C...This paper reports a continuous-wave (CW) mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate (PPLN) pumped by a diode-end-pumped CW Nd:YVO4 laser. Considering the thermal lens effects, it adopted an optical ballast lens and the near-concentric cavity for better operation. At the PPLN's grating period of 28.5 μm and the temperature of 140℃, the maximum idler output power of 155 mW at 3.86 μm has been achieved when the 808 nm pump power is 8.5 W, leading to an optical-to-optical conversion efficiency of 1.82%.展开更多
In this paper we report on a continuous-wave (CW) intracavity singly resonant optical parametric oscillator (ICSRO) based on periodically poled LiNbO3 (PPLN) pumped by a diode-end-pumped CW Nd:YVO4 laser. Consi...In this paper we report on a continuous-wave (CW) intracavity singly resonant optical parametric oscillator (ICSRO) based on periodically poled LiNbO3 (PPLN) pumped by a diode-end-pumped CW Nd:YVO4 laser. Considering the thermal lens effects and diffraction loss, an optical ballast lens and a near-concentric cavity are adopted for better operation. Through varying the grating period and the temperature, the tunable signal output from 1406 nm to 1513 nm is obtained. At a PPLN grating period of 29 pm and a temperature of 413 K, a maximum signal output power of 820 mW at 1500 nm is achieved when the 808 nm pump power is 10.9 W, leading to an optical-to-optical conversion efficiency of 7.51%.展开更多
文摘Previous studies done elsewhere have shown that Eucalyptus poles treated with chromated copper arsenate (CCA) can last over 30 years. Kenya is exceptional because in some eco-regions, the Eucalyptus poles’ life span has greatly reduced to 5 years. The current study was designed to evaluate wood deteriorating agents of CCA-treated Eucalyptus poles and variability in four eco-regions of Kenya, namely, dryland, coastal, highland and humid lake. A total of 360 Eucalyptus pole samples were used for this experiment. Three CCA treatments were used to treat transmission poles at 20 kg/cm3 fencing posts samples at 6 kg/cm3, and a control group. Results indicated that termites and wood-decay fungi attacks caused wood deterioration in the four eco-regions. The proportion of power transmission pole degradation by wood deteriorating agents varied across eco-regions, between treatments and control and between time after treatments. Dryland eco-regions had the highest termite-related degradation (41.82%) while wood-decay fungi attack was highest in the highland eco-regions (9.20%). Samples treated with 6 kg/cm3 recorded the lowest level of wood deterioration, manifested by minimal superficial termite and wood-decay fungi attack. Samples treated with 20 kg/cm3 were characterized by moderate termite and wood-decay fungi attacks observed around the heartwood region, unlike sapwood. This study concluded that the deterioration of Eucalyptus CCA-treated poles is a question of climatic variability and hence, to increase the poles’ lifespan, CCA treatment should be tailored according to the characteristics of the ecoregion of use. Further investigations will inform the diversity of termites and decay-fungi across different eco-regions.
基金supported by the National Natural Science Foundation of China under project 52007047the Outstanding Youth Innovation Project funded by State Key Laboratory of Reliability and Intelligence of Electrical Equipment EERI_OY2021005。
文摘Permanent magnet claw pole machine(PMCPM) is a special kind of transverse flux permanent magnet machine. Compared with other electrical machines, it has the advantages of high torque density and high efficiency for high speed operation. However, because of its complex irregular structure, the manufacturing process using silicon sheets is complicated. Soft magnetic composite material(SMC) is manufactured by powder metallurgy technology, which can produce various shapes of stator core structures, so it is easier to produce various irregular shapes of the stator core. However, the raw SMC material is relatively expensive, and the mechanical strength of SMC is weak. In this paper, a PMCPM with hybrid cores is proposed. With the adoption of hybrid silicon sheet-SMC cores and amorphous alloy-SMC cores, the torque ability of PMCPM can be improved greatly and it can have higher efficiency for more wide operation frequency. Meanwhile, its mechanical strength has been improved and it can be designed for high torque direct drive applications as it is a modular machine. Furthermore, three methods are proposed to reduce the additional eddy current loss which resulted from the employment of hybrid cores in PMCPM.
文摘Objective:To evaluate the long-term stone-free rate(SFR)of retrograde intrarenal surgery(RIRS)in the treatment of lower pole renal calculi using only basket relocation and identify independent predictors of stone-free status.Methods:All consecutive patients undergoing RIRS lower pole renal calculi at a single highvolume tertiary center were analyzed retrospectively.Lower pole stones were relocated to the upper pole,where laser lithotripsy was performed.All patients were followed up in the clinic following the surgery and yearly thereafter.The stone-free status was assessed with a combination of an abdominal ultrasound and abdominal X-ray,or an abdominal non-contrast computed tomography if the stones were known to be radiolucent.Results:A total of 480 consecutive patients who underwent RIRS for treatment of lower pole renal calculi,between January 2012 and December 2018,were analyzed from a prospectively maintained database of 3000 ureteroscopies.With a median follow-up time of 18.6 months,the mean SFR was 94.8%.The procedures were unsuccessful in 26(5.4%)patients due to unreachable stones.The median stone size of the unreachable stones was 12 mm(range 10e30 mm).Multivariable logistic regression analysis revealed two predictors of SFR for lower pole stones:a small cumulative stone burden(odds ratio[OR]:0.903,95%confidence interval[CI]:0.867e0.941,p<0.0001)and preoperative ureteral stent insertion(OR:0.515,95%CI:0.318e0.835,pZ0.007).Conclusion:The long-term SFR of RIRS for the treatment of lower pole stones with basket displacement with appropriate patient selection is high.
基金supported by the National Natural Science Foundation of China under project 52007047in part by the Outstanding Youth Innovation Project funded by State Key Laboratory of Reliability and Intelligence of Electrical Equipment EERI_OY2021005,and EERI_KF2021014。
文摘Soft magnetic composite(SMC)material is an ideal soft magnetic material employed for developing 3D magnetic flux electromagnetic equipment,due to its advantages of 3D magnetic isotropy characteristic,low eddy current loss,and simple manufacturing process.The permanent magnet claw pole machine(PMCPM)with SMC cores is a good case that the SMC to be adopted for developing 3D flux electrical machines.In this paper,a novel axial-radial flux permanent magnet claw pole machine(ARPMCPM)with SMC cores and ferrite magnets is proposed.Compared with the traditional PMCPM,the proposed ARPMCPM is designed with only one spoke PM rotor and its whole structure is quite compact.For the performance prediction,the 3D finite element method(FEM)is used.Meanwhile,for the performance evaluation,a previously developed axial flux claw pole permanent magnet machine(AFCPM)is employed as the benchmark machine and all these machines are optimized by using the combined multilevel robust Taguchi method.It can be seen that the proposed ARPMCPM is with higher torque/weight density and operation efficiency.
文摘The idea of research started with a crazy imaginary theory in the field of astrogeography, saying: We often taught ourselves and then convinced the students that the planet Earth moves despite not feeling the vibrations of traffic, and we listed successive scientific confirmations to indicate the rotation of the planet in a regular movement around its axis once every 24 hours, and it is running in another second movement around the sun once every 365¼ days, so are they only two movements, no more?! Is it possible for him to run at a regular speed in an additional direction?
文摘The present work deals with reducing greenhouse gas emissions through improving the life span of wooden power electric poles of Eucalyptus saligna. Indeed, in Sub-Saharan African countries, Cameroon in particular, most of the power line networks are made of wooden supports and according to the Cameroon energy distribution company, wooden poles represent 32% of the causes of death linked to the state of the network. The company’s 2019 annual report indicates that 40,000 wooden poles were in critical condition and should be replaced. A significant number of mechanical failures affecting these supports have been observed. For example, on the HVA/LV power line “D17 Nko- abang” in Yaoundé in Cameroon, less than three years old, 10 (ten) cases of poles falling and/or breaking, due to their mechanical loading, were observed over a period of fewer than nine months, causing an average service stoppage for more than 11 hours and affecting an average of 3280 customers. These incidents lead to questions about how the supports are dimensioned and what load capacities they are designed to support. The aim of this work is, therefore, to suggest a method of dimensioning wooden poles hence reducing green- house gas emissions due to the deforestation by reducing the number of woo- den poles at risk to be replaced on Cameroon’s electricity distribution network. And more specifically, to reduce the number of mechanical failures affecting the wooden supports observed by analyzing the current wooden supports with their loads and to make proposals for improving the actual dimensioning me- thods. From the study carried out, it appears that 449 out of 845 supports, i.e., 53% needed to be replaced or monitored because they support the nominal forces ranging from 85% to 150% of their admissible limit and proposals have been made to improve their dimensioning.
基金Hefei CAS Ion Medical and Technical Devices Co., Ltd. for their financial support of our research
文摘The design, field quality optimization, multipole field analysis, and field measurement of a dipole for a newly developed superconducting proton cyclotron(SC200) beamline are presented in this paper. The maximum magnetic field of the dipole is 1.35 T; the bending radius is 1.6 m with a proton beam energy in the range of70–200 Me V. The magnetic field was calculated with 2 D and 3 D simulations, and measured with a Hall mapping system. The pole shim and end chamfer were optimized to improve the field quality. Based on the simulated results,the multipole field components in the good-field region were studied to evaluate the field quality. The results showed that the field quality is better than ± 5 × 10^(-4) at1.35 T with shimming and chamfering. For the transverse field homogeneity, the third-order(B3) and fifth-order(B5)components should be controlled with symmetrical shims.The second-order(B2) component was the main disturbance for the integral field homogeneity; it could be improved with an end chamfer. The magnet manufacturing and field measurement were performed in this project. The measurement results demonstrated that the magnetic design and field quality optimization of the 45° dipole magnet can achieve the desired high field quality and satisfy the physical requirements.
文摘The soft switching operation principle and operation performance of rugged resonant pole (RRP) is given. The applications of RRP in soft switching DC DC converter and soft switching inverter are discussed in detail. RRP can constitute buck boost soft switching DC DC converter and isolated soft switching DC DC converter with the automatic limitation performance of output power. Partial series resonant DC DC converter with RRP can realize the zero voltage/zero current switching of power devices. RR...
文摘A Mach-Zehnder(MZ) electro-optic(EO) modulator are real iz ed,with three optical layers as polymer materials.The functional layer is the co rona poled crosslinkable polyurethane.The ridge waveguide is fabricated by using the spin-coating,poling,photolithography and oxygen reactive ion etching(RIE) techniques.The mode and the modulation properties of these devices are demonstra ted in a micron control system,while the light source works at the wavelength of 1 31 or 1 55 micron.
文摘Electrochemical machining (ECM) is one of the best al ternatives for producing complex shapes in advanced materials used in aircraft a nd aerospace industries. However, the reduction of the stray material removal co ntinues to be major challenges for industries in addressing accuracy improvement . This study presents a method of improving machining accuracy in ECM by using a dual pole tool with a metallic bush outside the insulated coating of a cathode tool. The bush is connected with anode and so the electric field at the side gap area is substantially weakened. The modeling and simulation indicate that the p ositive bush brings down the current density at the side gap area of the machine d hole and hence reduces the stray material removal there. It has been experimen tally observed that the machining accuracy and the process stability are signifi cantly improved.
基金Supported by the Ningbo Medical Science and Technology Project,No.2014A33
文摘AIM To compare the outcomes of retrograde intrarenal surgery(RIRS) and miniaturized percutaneous nephrolithotomy(mini-PCNL) in treating lower pole(LP) renal stones with a diameter of 1.5-2.5 cm.METHODS A total of 216 patients who underwent mini-PCNL(n = 103) or RIRS n = 113) for LP stones with a diameter of 1.5-2.5 cm were enrolled between December 2015 and April 2017 at the Urology Department of Ningbo Urology and Nephrology Hospital.RESULTS Significant differences were found in the hospital stay(9.39 ± 4.01 vs 14.08 ± 5.26, P < 0.0001) and hospitalization costs(2624.5 ± 513.36 vs 3255.2 ± 976.5, P < 0.0001) between the RIRS and mini-PCNL groups. The mean operation time was not significantly different between the RIRS group(56.48 ± 24.77) and the mini-PCNL group(60.04 ± 30.38, P = 0.345). The stone-free rates at the first postoperative day(RIRS vs mini-PCNL: 90.2% vs 93.2%, P = 0.822) and the second month postoperatively(RIRS vs mini-PCNL: 93.8% vs 95.1%, P = 0.986) were not significantly different.CONCLUSION RIRS and mini-PCNL are both safe and effective methods for treating LP stones with a diameter of 1.5-2.5 cm. RIRS can be considered as an alternative to PCNL for the treatment for LP stones of 1.5-2.5 cm.
基金Project supported in part by the National Natural Science Foundation of China (Grant Nos 10474071, 60637010, 60671036 and60278001)Tianjin Applied Fundamental Research Project, China (07JCZDJC05900)
文摘This paper reports a continuous-wave (CW) mid-infrared intracavity singly resonant optical parametric oscillator based on periodically poled lithium niobate (PPLN) pumped by a diode-end-pumped CW Nd:YVO4 laser. Considering the thermal lens effects, it adopted an optical ballast lens and the near-concentric cavity for better operation. At the PPLN's grating period of 28.5 μm and the temperature of 140℃, the maximum idler output power of 155 mW at 3.86 μm has been achieved when the 808 nm pump power is 8.5 W, leading to an optical-to-optical conversion efficiency of 1.82%.
基金Project supported partly by the National Natural Science Foundation of China (Grant Nos 60637010 and 60671036)the National Basic Research Program of China (Grant No 2007CB310403)the Tianjin Applied Fundamental Research Project, China(Grant No 07JCZDJC05900)
文摘In this paper we report on a continuous-wave (CW) intracavity singly resonant optical parametric oscillator (ICSRO) based on periodically poled LiNbO3 (PPLN) pumped by a diode-end-pumped CW Nd:YVO4 laser. Considering the thermal lens effects and diffraction loss, an optical ballast lens and a near-concentric cavity are adopted for better operation. Through varying the grating period and the temperature, the tunable signal output from 1406 nm to 1513 nm is obtained. At a PPLN grating period of 29 pm and a temperature of 413 K, a maximum signal output power of 820 mW at 1500 nm is achieved when the 808 nm pump power is 10.9 W, leading to an optical-to-optical conversion efficiency of 7.51%.