In order to improve the performance degradation prediction accuracy of proton exchange membrane fuel cell(PEMFC),a fusion prediction method(CKDG)based on adaptive noise complete ensemble empirical mode decomposition(C...In order to improve the performance degradation prediction accuracy of proton exchange membrane fuel cell(PEMFC),a fusion prediction method(CKDG)based on adaptive noise complete ensemble empirical mode decomposition(CEEMDAN),kernel principal component analysis(KPCA)and dual attention mechanism gated recurrent unit neural network(DA-GRU)was proposed.CEEMDAN and KPCA were used to extract the input feature data sequence,reduce the influence of random factors,and capture essential feature components to reduce the model complexity.The DA-GRU network helps to learn the feature mapping relationship of data in long time series and predict the changing trend of performance degradation data more accurately.The actual aging experimental data verify the performance of the CKDG method.The results show that under the steady-state condition of 20%training data prediction,the CKDA method can reduce the root mean square error(RMSE)by 52.7%and 34.6%,respectively,compared with the traditional LSTM and GRU neural networks.Compared with the simple DA-GRU network,RMSE is reduced by 15%,and the degree of over-fitting is reduced,which has higher accuracy.It also shows excellent prediction performance under the dynamic condition data set and has good universality.展开更多
High-temperature proton exchange membrane fuel cells(HT-PEMFC) possess distinct technical advantages of high output power, simplified water/heat management, increased tolerance to fuel impurities and diverse fuel sour...High-temperature proton exchange membrane fuel cells(HT-PEMFC) possess distinct technical advantages of high output power, simplified water/heat management, increased tolerance to fuel impurities and diverse fuel sources, within the temperature range of 120–200 ℃. However, for practical automobile applications, it was crucial to broaden their low-temperature operating window and enable cold start-up capability. Herein, gel-state phosphoric acid(PA) doped sulfonated polybenzimidazole(PBI) proton exchange membranes(PEMs) were designed and synthesized via PPA sol-gel process and in-situ sultone ring-opening reactions with various proton transport pathways based on absorbed PA, flexible alkyl chain connected sulfonic acid groups and imidazole sites. The effects of flexible alkyl sulfonic acid side chain length and content on PA doping level, proton conductivity, and membrane stability under different temperature and relative humidity(RH) were thoroughly investigated. The prepared gel-state membranes contained a self-assembled lamellar and porous structure that facilitated the absorption of a large amount of PA with rapid proton transporting mechanisms. At room temperature, the optimized membrane exhibited a proton conductivity of 0.069 S cm^(-1), which was further increased to 0.162 and 0.358 S cm^(-1)at 80 and 200 ℃, respectively, without additional humidification. The most significant contribution of this work was demonstrating the feasibility of gel-state sulfonated PBI membranes in expanding HT-PEMFC application opportunities over a wider operating range of 25 to 240 ℃.展开更多
A three-dimensional multicomponent multiphase lattice Boltzmann model(LBM)is established to model the coupled two-phase and reactive transport phenomena in the cathode electrode of proton exchange membrane fuel cells....A three-dimensional multicomponent multiphase lattice Boltzmann model(LBM)is established to model the coupled two-phase and reactive transport phenomena in the cathode electrode of proton exchange membrane fuel cells.The gas diff usion layer(GDL)and microporous layer(MPL)are stochastically reconstructed with the inside dynamic distribution of oxygen and liquid water resolved,and the catalyst layer is simplifi ed as a superthin layer to address the electrochemical reaction,which provides a clear description of the fl ooding eff ect on mass transport and performance.Diff erent kinds of electrodes are reconstructed to determine the optimum porosity and structure design of the GDL and MPL by comparing the transport resistance and per-formance under the fl ooding condition.The simulation results show that gradient porosity GDL helps to increase the reactive area and average concentration under fl ooding.The presence of the MPL ensures the oxygen transport space and reaction area because liquid water cannot transport through micropores.Moreover,the MPL helps in the uniform distribution of oxygen for an effi cient in-plane transport capacity.Crack and perforation structures can accelerate the water transport in the assembly.The systematic perforation design yields the best performance under fl ooding by separating the transport of liquid water and oxygen.展开更多
Proton exchange membrane fuel cells(PEMFCs)are largely used in various applications because of their pollution-free products and high energy conversion efficiency.In order to improve the related design,in the present ...Proton exchange membrane fuel cells(PEMFCs)are largely used in various applications because of their pollution-free products and high energy conversion efficiency.In order to improve the related design,in the present work a new spiral flow field with a bypass is proposed.The reaction gas enters the flow field in the central path and diffuses in two directions through the flow channel and the bypass.The bypasses are arranged incrementally.The number of bypasses and the cross-section size of the bypasses are varied parametrically while a single-cell model of the PEMFC is used.The influence of the concentration of liquid water and oxygen in the cell on the performance of different flow fields is determined by means of Computational fluid dynamics(COMSOL Multiphysics software).Results show that when the bypass number is 48 and its cross-sectional area is 0.5 mm^(2),the cell exhibits the best performances.展开更多
Arc ion plating (AIP) is applied to form Ti/(Ti,Cr)N/CrN multilayer coating on the surface of 316L stainless steel (SS316L) as bipolar plates for proton exchange membrane fuel cells (PEMFCs). The characterizations of ...Arc ion plating (AIP) is applied to form Ti/(Ti,Cr)N/CrN multilayer coating on the surface of 316L stainless steel (SS316L) as bipolar plates for proton exchange membrane fuel cells (PEMFCs). The characterizations of the coating are analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Interfacial contact resistance (ICR) between the coated sample and carbon paper is 4.9 m Omega cm(2) under 150 N/cm(2), which is much lower than that of the SS316L substrate. Potentiodynamic and potentiostatic tests are performed in the simulated PEMFC working conditions to investigate the corrosion behaviors of the coated sample. Superior anticorrosion performance is observed for the coated sample, whose corrosion current density is 0.12 mu A/cm(2). Surface morphology results after corrosion tests indicate that the substrate is well protected by the multilayer coating. Performances of the single cell with the multilayer coated SS316L bipolar plate are improved significantly compared with that of the cell with the uncoated SS316L bipolar plate, presenting a great potential for PEMFC application. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.展开更多
Proton exchange membrane fuel cell(PEMFC)powered automobiles have been recognized to be the ultimate solution to replace traditional fuel automobiles because of their advantages of PEMFCs such as no pollution,low temp...Proton exchange membrane fuel cell(PEMFC)powered automobiles have been recognized to be the ultimate solution to replace traditional fuel automobiles because of their advantages of PEMFCs such as no pollution,low temperature start-up,high energy density,and low noise.As one of the core components,the bipolar plates(BPs)play an important role in the PEMFC stack.Traditional graphite BPs and composite BPs have been criticized for their shortcomings such as low strength,high brittleness,and high processing cost.In contrast,stainless steel BPs(SSBPs)have recently attracted much attention of domestic and foreign researchers because of their excellent comprehensive performance,low cost,and diverse options for automobile applications.However,the SSBPs are prone to corrosion and passivation in the PEMFC working environment,which lead to reduced output power or premature failure.This review is aimed to summarize the corrosion and passivation mechanisms,characterizations and evaluation,and the surface modification technologies in the current SSBPs research.The non-coating and coating technical routes of SSBPs are demonstrated,such as substrate component regulation,thermal nitriding,electroplating,ion plating,chemical vapor deposition,and physical vapor deposition,etc.Alternative coating materials for SSBPs are metal coatings,metal nitride coatings,conductive polymer coatings,and polymer/carbon coatings,etc.Both the surface modification technologies can solve the corrosion resistance problem of stainless steel without affecting the contact resistance,however still facing restraints such as long-time stability,feasibility of low-cost,and mass production process.This paper is believed to enrich the knowledge of high-performance and long-life BPs applied for PEMFC automobiles.展开更多
The novel sulfonated polybenzimidazole(sPBI)/amine functionalized titanium dioxide(AFT) composite membrane is devised and studied for its capability of the application of high temperature proton exchange membrane fuel...The novel sulfonated polybenzimidazole(sPBI)/amine functionalized titanium dioxide(AFT) composite membrane is devised and studied for its capability of the application of high temperature proton exchange membrane fuel cells(HT-PEMFCs),unlike the prior low temperature AFT endeavors.The high temperature compatibility was actualized because of the filling of free volumes in the rigid aromatic matrix of the composite with AFT nanoparticles which inhibited segmental motions of the chains and improved its thermal stability.Besides,amine functionalization of TiO2 enhanced their dispersion character in the sPBI matrix and shortened the interparticle separation gap which finally improved the proton transfer after establishing interconnected pathways and breeding more phosphoric acid(PA) doping.In addition,the appeared assembled clusters of AFT flourished a superior mechanical stability.Thus,the optimized sPBI/AFT(10 wt%) showed 65.3 MPa tensile strength;0.084 S·cm^-1 proton conductivity(at 160℃;in anhydrous conditions),28.6% water uptake and PA doping level of 23 mol per sPBI repeat unit.The maximum power density peak for sPBI/AFT-10 met the figure of0.42 W·cm^-2 at 160℃(in dry conditions) under atmospheric pressure with 1.5 and 2.5 stoichiometric flow rates of H2/air.These results affirmed the probable fitting of sPBI/AFT composite for HT-PEMFC applications.展开更多
Pt/WO3/C nanocomposites with parallel WO3 nanorods were synthesized and applied as the cathode catalyst for proton exchange membrane fuel cells (PEMFCs). Electrochemical results and single cell tests show that an en...Pt/WO3/C nanocomposites with parallel WO3 nanorods were synthesized and applied as the cathode catalyst for proton exchange membrane fuel cells (PEMFCs). Electrochemical results and single cell tests show that an enhanced activity for the oxygen reduction reaction (ORR) is obtained for the Pt/WO3/C catalyst compared with Pt/C. The higher catalytic activity might be ascribed to the improved Pt dispersion with smaller particle sizes. The Pt/WO3/C catalyst also exhibits a good electrochemical stability under potential cycling. Thus, the Pt/WO3/C catalyst can be used as a potential PEMFC cathode catalyst.展开更多
316L stainless steel(SS 316L) is quite attractive as bipolar plates in proton exchange membrane fuel cells(PEMFC).In this study,graphite-polypyrrole was coated on SS 316L by the method of cyclic voltammetry.The su...316L stainless steel(SS 316L) is quite attractive as bipolar plates in proton exchange membrane fuel cells(PEMFC).In this study,graphite-polypyrrole was coated on SS 316L by the method of cyclic voltammetry.The surface morphology and chemical composition of the graphite-polypyrrole composite coating were investigated by scanning electron microscopy(SEM) and X-ray photoelectron spectroscopy(XPS).A simulated working environment of PEMFC was applied for testing the corrosion properties of graphite-polypyrrole coated SS 316L.The current densities in the simulated PEMFC anode and cathode conditions are around 3×10-9 and 9×10-5 A·cm-2,respectively.In addition,the interfacial contact resistance(ICR) was also investigated.The ICR value of graphite-polypyrrole coated SS 316L is much lower than that of bare SS 316L.Therefore,graphite-polypyrrole coated SS 316L indicates a great potential for the application in PEMFC.展开更多
High-temperature proton exchange membrane fuel cells(HT-PEMFCs)are pursued worldwide as efficient energy conversion devices.Great efforts have been made in the area of designing and developing phosphoric acid(PA)-base...High-temperature proton exchange membrane fuel cells(HT-PEMFCs)are pursued worldwide as efficient energy conversion devices.Great efforts have been made in the area of designing and developing phosphoric acid(PA)-based proton exchange membrane(PEM)of HT-PEMFCs.This review focuses on recent advances in the limitations of acid-based PEM(acid leaching,oxidative degradation,and mechanical degradation)and the approaches mitigating the membrane degradation.Preparing multilayer or polymers with continuous network,adding hygroscopic inorganic materials,and introducing PA doping sites or covalent interactions with PA can effectively reduce acid leaching.Membrane oxidative degradation can be alleviated by synthesizing crosslinked or branched polymers,and introducing antioxidative groups or highly oxidative stable materials.Crosslinking to get a compact structure,blending with stable polymers and inorganic materials,preparing polymer with high molecular weight,and fabricating the polymer with PA doping sites away from backbones,are recommended to improve the membrane mechanical strength.Also,by comparing the running hours and decay rate,three current approaches,1.crosslinking via thermally curing or polymeric crosslinker,2.incorporating hygroscopic inorganic materials,3.increasing membrane layers or introducing strong basic groups and electron-withdrawing groups,have been concluded to be promising approaches to improve the durability of HT-PEMFCs.The overall aim of this review is to explore the existing degradation challenges and opportunities to serve as a solid basis for the deployment in the fuel cell market.展开更多
An extensive study has been conducted on the proton exchange membrane fuel cells (PEMFCs) with reducing Pt loading. This is commonly achieved by developing methods to increase the utilization of the platinum in the ...An extensive study has been conducted on the proton exchange membrane fuel cells (PEMFCs) with reducing Pt loading. This is commonly achieved by developing methods to increase the utilization of the platinum in the catalyst layer of the electrodes. In this paper, a novel process of the catalyst layers was introduced and investigated. A mixture of carbon powder and Nafion solution was sprayed on the glassy carbon electrode (GCE) to form a thin carbon layer. Then Pt particles were deposited on the surface by reducing hexachloroplatinic (IV) acid hexahydrate with methanoic acid. SEM images showed a continuous Pt gradient profile among the thickness direction of the catalytic layer by the novel method. The Pt nanowires grown are in the size of 3 nm (diameter) x l0 nm (length) by high solution TEM image. The novel catalyst layer was characterized by cyclic voltammetry (CV) and scanning electron microscope (SEM) as compared with commercial Pt/C black and Pt catalyst layer obtained from sputtering. The results showed that the platinum nanoparticles deposited on the carbon powder were highly utilized as they directly faced the gas diffusion layer and offered easy access to reactants (oxygen or hydrogen).展开更多
Proton exchange membranes (PEMs) are a key material for proton exchange membrane fuel cells (PEM-FCs), Non-fluorinated hydrocarbon PEMs are low-cost alternatives to Nation, but limited by the low pro-ton conductiv...Proton exchange membranes (PEMs) are a key material for proton exchange membrane fuel cells (PEM-FCs), Non-fluorinated hydrocarbon PEMs are low-cost alternatives to Nation, but limited by the low pro-ton conductivity, because of the weak phase segregation structure and narrow ion-transport channels.Various efforts have been taken to improve the performance of hydrocarbon PEMs, but mostly with com-plex methodologies. Here we demonstrate a simple, yet very efficient method to create phase segrega-tion structure inside a typical hydrocarbon PEM, sulfonated poly(ether ether ketone) (SPEEK). By sim-ply adding appropriate amounts of water into the DMF solvent, the resulting SPEEK membrane exhibitswidened ion-transport channels, with the phase size of 2.7 nm, as indicated by both molecular dynamic(MD) simulations and transmission electron microscope (TEM) observations, and the proton conductivityis thus improved by 200%. These findings not only further our fundamental understanding of hydrocarbonPEMs, but are also valuable to the development of low-cost and practical fuel cell technologies.展开更多
Silica nanosheets(SN)derived from natural vermiculite(Verm)were successfully incorporated into polyethersulfone-polyvinylpyrrolidone(PES-PVP)polymer to fabricate high-temperature proton exchange membranes(HT-PEMs).The...Silica nanosheets(SN)derived from natural vermiculite(Verm)were successfully incorporated into polyethersulfone-polyvinylpyrrolidone(PES-PVP)polymer to fabricate high-temperature proton exchange membranes(HT-PEMs).The content of SN filler was varied(0.1-0.75 wt%)to study its influence on proton conductivity,power density and durability.Benefiting from the hydroxyl groups of SN that enable the formation of additional proton-transferring pathways,the inorganic-organic membrane displayed enhanced proton conductivity of 48.2 mS/cm and power density of 495 mW/cm^(2) at 150℃ without humidification when the content of SN is 0.25 wt%.Furthermore,exfoliated SN(E-SN)and sulfonated SN(S-SN),which were fabricated by a liquid-phase exfoliation method and silane condensation,respectively,were embedded in PES-PVP polymer matrix by a simple blending method.Due to the significant contribution from sulfonic groups in S-SN,the membrane with 0.25 wt%S-SN reached the highest proton conductivity of51.5 mS/cm and peak power density of 546 mW/cm^(2) at150℃,48%higher than the pristine PES-PVP membranes.Compared to unaltered PES-PVP membrane,SN added hybrid composite membrane demonstrated excellent durability for the fuel cell at 150℃.Using a facile method to prepare 2D SN from natural clay minerals,the strategy of exfoliation and functionalization of SN can be potentially used in the production of HT-PEMs.展开更多
Distribution expressions of total gas pressure and partial water vapor pressure along the channel direction were established based on lumped model by analyzing pressure loss in the channel and gas diffusion in the lay...Distribution expressions of total gas pressure and partial water vapor pressure along the channel direction were established based on lumped model by analyzing pressure loss in the channel and gas diffusion in the layer. The mechanism of droplet formation in the flow channel was also analyzed. Effects of the relative humidity, working temperature and stoichiometry on liquid water formation were discussed in detail. Moreover, the force equilibrium equation of the droplet in the flow channel was deduced, and the critical flow velocity for the water droplet removal was also addressed. The experimental results show that the threshold position of the liquid droplet is far from the inlet with the increase of temperature, and it decreases with the increase of the inlet total pressure. The critical flow velocity decreases with the increase of the radius and the working pressure.展开更多
Novel SPPESK/PAA composite proton exchange membranes with semi-interpenetrating polymer network (sIPN) structure have been synthesized through the in-situ polymerization of acrylic acid (AA) in the presence of sul...Novel SPPESK/PAA composite proton exchange membranes with semi-interpenetrating polymer network (sIPN) structure have been synthesized through the in-situ polymerization of acrylic acid (AA) in the presence of sulfonated poly (phthalazinone ether sulfone ketone) (SPPESK). The composite membranes were identified by FT-IR analysis. Water uptake of the composite membranes was as high as 89.7% at 90℃, nearly one time higher than that of the corresponding SPPESK membrane.展开更多
To prevent the oxygen starvation and improve the system output performance, an adaptive inverse control (AIC) strategy is developed to regulate the air supply flow of a proton exchange membrane fuel cell (PEMFC) s...To prevent the oxygen starvation and improve the system output performance, an adaptive inverse control (AIC) strategy is developed to regulate the air supply flow of a proton exchange membrane fuel cell (PEMFC) system in this paper. The PEMFC stack and the air supply system including a compressor and a supply manifold are modeled for the purpose of performance analysis and controller design. A recurrent fuzzy neural network (RFNN) is utilized to identify the inverse model of the controlled system and generates a suitable control input during the abrupt step change of external disturbances. Compared with the PI controller, numerical simulations are performed to validate the effectiveness and advantages of the proposed AIC strategy.展开更多
In order to improve the proton conductivity of hollow silica spheres (HSS)/perfluorosulfonic acid ion-exchange (PFSA) composite membranes as proton exchange membrane,sulfonic acid groups were grafted onto the surf...In order to improve the proton conductivity of hollow silica spheres (HSS)/perfluorosulfonic acid ion-exchange (PFSA) composite membranes as proton exchange membrane,sulfonic acid groups were grafted onto the surfaces of HSS via post grafting methods.TEM images and FT-IR spectra of the obtained sulfonic acid groups modified hollow silica spheres (SAMHSS) illustrated that the sulfonic acid groups were successfully grafted onto the surfaces of HSS.Water uptake and swelling degree of SAMHSS/PFSA composite membranes were found much higher than those of HSS/PFSA membranes due to the introduction of hydrophilic sulfonic acid groups.In a range from 50 ℃ to 130 ℃,the highest conductivity of composite membranes was obtained when 5 wt% SAMHSS was loaded.The maximum conductivity reached 7.5×10-2 S·cm-1 at 100 ℃ and 100% relative humidity,even the temperature increased to 130 ℃,the conductivity of composite membranes with 5 wt% SAMHSS could reach 3.7×10-2 S·cm-1 at 100 % relative humidity,while the conductivity of the recast PFSA was only 2.2×10-3 S·cm-1.展开更多
Reducing a Pt loading with improved power output and durability is essential to promote the large-scale application of proton exchange membrane fuel cells(PEMFCs).To achieve this goal,constructing optimized structure ...Reducing a Pt loading with improved power output and durability is essential to promote the large-scale application of proton exchange membrane fuel cells(PEMFCs).To achieve this goal,constructing optimized structure of catalyst layers with efficient mass transportation channels plays a vital role.Herein,PEMFCs with order-structured cathodic electrodes were fabricated by depositing Pt nanoparticles by Ebeam onto vertically aligned carbon nanotubes(VACNTs)growth on Al foil via plasma-enhanced chemical vapor deposition.Results demonstrate that the proportion of hydrophilic Pt-deposited region along VACNTs and residual hydrophobic region of VANCTs without Pt strongly influences the cell performance,in particular at high current densities.When Pt nanoparticles deposit on the top depth of around 600 nm on VACNTs with a length of 4.6μm,the cell shows the highest performance,compared with others with various lengths of VACNTs.It delivers a maximum power output of 1.61 W cm^(-2)(H_(2)/O_(2),150 k Pa)and 0.79 W cm^(-2)(H_(2)/Air,150 k Pa)at Pt loading of 50μg cm^(-2),exceeding most of previously reported PEMFCs with Pt loading of<100μg cm^(-2).Even though the Pt loading is down to 30μg cm^(-2)(1.36 W cm^(-2)),the performance is also better than 100μg cm^(-2)(1.24 W cm^(-2))of commercial Pt/C,and presents better stability.This excellent performance is critical attributed to the ordered hydrophobic region providing sufficient mass passages to facilitate the fast water drainage at high current densities.This work gives a new understanding for oxygen reduction reaction occurred in VACNTs-based ordered electrodes,demonstrating the most possibility to achieve a substantial reduction in Pt loading<100μg cm^(-2) without sacrificing in performance.展开更多
基金funded by Shaanxi Province Key Industrial Chain Project(2023-ZDLGY-24)Industrialization Project of Shaanxi Provincial Education Department(21JC018)+1 种基金Shaanxi Province Key Research and Development Program(2021ZDLGY13-02)the Open Foundation of State Key Laboratory for Advanced Metals and Materials(2022-Z01).
文摘In order to improve the performance degradation prediction accuracy of proton exchange membrane fuel cell(PEMFC),a fusion prediction method(CKDG)based on adaptive noise complete ensemble empirical mode decomposition(CEEMDAN),kernel principal component analysis(KPCA)and dual attention mechanism gated recurrent unit neural network(DA-GRU)was proposed.CEEMDAN and KPCA were used to extract the input feature data sequence,reduce the influence of random factors,and capture essential feature components to reduce the model complexity.The DA-GRU network helps to learn the feature mapping relationship of data in long time series and predict the changing trend of performance degradation data more accurately.The actual aging experimental data verify the performance of the CKDG method.The results show that under the steady-state condition of 20%training data prediction,the CKDA method can reduce the root mean square error(RMSE)by 52.7%and 34.6%,respectively,compared with the traditional LSTM and GRU neural networks.Compared with the simple DA-GRU network,RMSE is reduced by 15%,and the degree of over-fitting is reduced,which has higher accuracy.It also shows excellent prediction performance under the dynamic condition data set and has good universality.
基金supported by the National Natural Science Foundation of China (NSFC-22209147)。
文摘High-temperature proton exchange membrane fuel cells(HT-PEMFC) possess distinct technical advantages of high output power, simplified water/heat management, increased tolerance to fuel impurities and diverse fuel sources, within the temperature range of 120–200 ℃. However, for practical automobile applications, it was crucial to broaden their low-temperature operating window and enable cold start-up capability. Herein, gel-state phosphoric acid(PA) doped sulfonated polybenzimidazole(PBI) proton exchange membranes(PEMs) were designed and synthesized via PPA sol-gel process and in-situ sultone ring-opening reactions with various proton transport pathways based on absorbed PA, flexible alkyl chain connected sulfonic acid groups and imidazole sites. The effects of flexible alkyl sulfonic acid side chain length and content on PA doping level, proton conductivity, and membrane stability under different temperature and relative humidity(RH) were thoroughly investigated. The prepared gel-state membranes contained a self-assembled lamellar and porous structure that facilitated the absorption of a large amount of PA with rapid proton transporting mechanisms. At room temperature, the optimized membrane exhibited a proton conductivity of 0.069 S cm^(-1), which was further increased to 0.162 and 0.358 S cm^(-1)at 80 and 200 ℃, respectively, without additional humidification. The most significant contribution of this work was demonstrating the feasibility of gel-state sulfonated PBI membranes in expanding HT-PEMFC application opportunities over a wider operating range of 25 to 240 ℃.
基金by the National Natural Science Foundation of China(No.51976138)National Engineering Laboratory for Mobile Source Emission Control Technology(No.NELMS2019A10).
文摘A three-dimensional multicomponent multiphase lattice Boltzmann model(LBM)is established to model the coupled two-phase and reactive transport phenomena in the cathode electrode of proton exchange membrane fuel cells.The gas diff usion layer(GDL)and microporous layer(MPL)are stochastically reconstructed with the inside dynamic distribution of oxygen and liquid water resolved,and the catalyst layer is simplifi ed as a superthin layer to address the electrochemical reaction,which provides a clear description of the fl ooding eff ect on mass transport and performance.Diff erent kinds of electrodes are reconstructed to determine the optimum porosity and structure design of the GDL and MPL by comparing the transport resistance and per-formance under the fl ooding condition.The simulation results show that gradient porosity GDL helps to increase the reactive area and average concentration under fl ooding.The presence of the MPL ensures the oxygen transport space and reaction area because liquid water cannot transport through micropores.Moreover,the MPL helps in the uniform distribution of oxygen for an effi cient in-plane transport capacity.Crack and perforation structures can accelerate the water transport in the assembly.The systematic perforation design yields the best performance under fl ooding by separating the transport of liquid water and oxygen.
基金Thanks to Major Scientific and Technological Innovation Projects in Shandong Province(2018-CXGC0803)for the financial support of this article.
文摘Proton exchange membrane fuel cells(PEMFCs)are largely used in various applications because of their pollution-free products and high energy conversion efficiency.In order to improve the related design,in the present work a new spiral flow field with a bypass is proposed.The reaction gas enters the flow field in the central path and diffuses in two directions through the flow channel and the bypass.The bypasses are arranged incrementally.The number of bypasses and the cross-section size of the bypasses are varied parametrically while a single-cell model of the PEMFC is used.The influence of the concentration of liquid water and oxygen in the cell on the performance of different flow fields is determined by means of Computational fluid dynamics(COMSOL Multiphysics software).Results show that when the bypass number is 48 and its cross-sectional area is 0.5 mm^(2),the cell exhibits the best performances.
基金financially supported by the National Basic Research Program of China (973 Program) (no. 2012CB215500)the National Key Technology Research and Development Program of China (no. 2015BAG06B00)+1 种基金Major Program of the National Natural Science Foundation of China (no. 61433013)National Natural Science Foundation of China (no. 21206012)
文摘Arc ion plating (AIP) is applied to form Ti/(Ti,Cr)N/CrN multilayer coating on the surface of 316L stainless steel (SS316L) as bipolar plates for proton exchange membrane fuel cells (PEMFCs). The characterizations of the coating are analyzed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Interfacial contact resistance (ICR) between the coated sample and carbon paper is 4.9 m Omega cm(2) under 150 N/cm(2), which is much lower than that of the SS316L substrate. Potentiodynamic and potentiostatic tests are performed in the simulated PEMFC working conditions to investigate the corrosion behaviors of the coated sample. Superior anticorrosion performance is observed for the coated sample, whose corrosion current density is 0.12 mu A/cm(2). Surface morphology results after corrosion tests indicate that the substrate is well protected by the multilayer coating. Performances of the single cell with the multilayer coated SS316L bipolar plate are improved significantly compared with that of the cell with the uncoated SS316L bipolar plate, presenting a great potential for PEMFC application. (C) 2016 Science Press and Dalian Institute of Chemical Physics, Chinese Academy of Sciences. Published by Elsevier B.V. and Science Press. All rights reserved.
基金supported by the National Natural Science Foundation of China(No.51704017)the National Key Research and Development plan of China(No.2018YFB1502403)the Communication Program for Young Scientist in USTB(No.QNXM20210010)。
文摘Proton exchange membrane fuel cell(PEMFC)powered automobiles have been recognized to be the ultimate solution to replace traditional fuel automobiles because of their advantages of PEMFCs such as no pollution,low temperature start-up,high energy density,and low noise.As one of the core components,the bipolar plates(BPs)play an important role in the PEMFC stack.Traditional graphite BPs and composite BPs have been criticized for their shortcomings such as low strength,high brittleness,and high processing cost.In contrast,stainless steel BPs(SSBPs)have recently attracted much attention of domestic and foreign researchers because of their excellent comprehensive performance,low cost,and diverse options for automobile applications.However,the SSBPs are prone to corrosion and passivation in the PEMFC working environment,which lead to reduced output power or premature failure.This review is aimed to summarize the corrosion and passivation mechanisms,characterizations and evaluation,and the surface modification technologies in the current SSBPs research.The non-coating and coating technical routes of SSBPs are demonstrated,such as substrate component regulation,thermal nitriding,electroplating,ion plating,chemical vapor deposition,and physical vapor deposition,etc.Alternative coating materials for SSBPs are metal coatings,metal nitride coatings,conductive polymer coatings,and polymer/carbon coatings,etc.Both the surface modification technologies can solve the corrosion resistance problem of stainless steel without affecting the contact resistance,however still facing restraints such as long-time stability,feasibility of low-cost,and mass production process.This paper is believed to enrich the knowledge of high-performance and long-life BPs applied for PEMFC automobiles.
基金supported by the National Natural Science Foundation of China(Nos.21776034,21476044 and 21406031)Joint Funds of the National Natural Science Foundation of China(U1663223)+1 种基金National Key Research and Development Program of China(2016YFB0101203)Changjiang Scholars Program(T2012049)。
文摘The novel sulfonated polybenzimidazole(sPBI)/amine functionalized titanium dioxide(AFT) composite membrane is devised and studied for its capability of the application of high temperature proton exchange membrane fuel cells(HT-PEMFCs),unlike the prior low temperature AFT endeavors.The high temperature compatibility was actualized because of the filling of free volumes in the rigid aromatic matrix of the composite with AFT nanoparticles which inhibited segmental motions of the chains and improved its thermal stability.Besides,amine functionalization of TiO2 enhanced their dispersion character in the sPBI matrix and shortened the interparticle separation gap which finally improved the proton transfer after establishing interconnected pathways and breeding more phosphoric acid(PA) doping.In addition,the appeared assembled clusters of AFT flourished a superior mechanical stability.Thus,the optimized sPBI/AFT(10 wt%) showed 65.3 MPa tensile strength;0.084 S·cm^-1 proton conductivity(at 160℃;in anhydrous conditions),28.6% water uptake and PA doping level of 23 mol per sPBI repeat unit.The maximum power density peak for sPBI/AFT-10 met the figure of0.42 W·cm^-2 at 160℃(in dry conditions) under atmospheric pressure with 1.5 and 2.5 stoichiometric flow rates of H2/air.These results affirmed the probable fitting of sPBI/AFT composite for HT-PEMFC applications.
基金financially supported by the National Natural Science Fundation of China(No.51125007)the National Basic Research Program(No.2012CB215500)
文摘Pt/WO3/C nanocomposites with parallel WO3 nanorods were synthesized and applied as the cathode catalyst for proton exchange membrane fuel cells (PEMFCs). Electrochemical results and single cell tests show that an enhanced activity for the oxygen reduction reaction (ORR) is obtained for the Pt/WO3/C catalyst compared with Pt/C. The higher catalytic activity might be ascribed to the improved Pt dispersion with smaller particle sizes. The Pt/WO3/C catalyst also exhibits a good electrochemical stability under potential cycling. Thus, the Pt/WO3/C catalyst can be used as a potential PEMFC cathode catalyst.
文摘316L stainless steel(SS 316L) is quite attractive as bipolar plates in proton exchange membrane fuel cells(PEMFC).In this study,graphite-polypyrrole was coated on SS 316L by the method of cyclic voltammetry.The surface morphology and chemical composition of the graphite-polypyrrole composite coating were investigated by scanning electron microscopy(SEM) and X-ray photoelectron spectroscopy(XPS).A simulated working environment of PEMFC was applied for testing the corrosion properties of graphite-polypyrrole coated SS 316L.The current densities in the simulated PEMFC anode and cathode conditions are around 3×10-9 and 9×10-5 A·cm-2,respectively.In addition,the interfacial contact resistance(ICR) was also investigated.The ICR value of graphite-polypyrrole coated SS 316L is much lower than that of bare SS 316L.Therefore,graphite-polypyrrole coated SS 316L indicates a great potential for the application in PEMFC.
基金funded by the UK Research Council EPSRC EP/009050/1。
文摘High-temperature proton exchange membrane fuel cells(HT-PEMFCs)are pursued worldwide as efficient energy conversion devices.Great efforts have been made in the area of designing and developing phosphoric acid(PA)-based proton exchange membrane(PEM)of HT-PEMFCs.This review focuses on recent advances in the limitations of acid-based PEM(acid leaching,oxidative degradation,and mechanical degradation)and the approaches mitigating the membrane degradation.Preparing multilayer or polymers with continuous network,adding hygroscopic inorganic materials,and introducing PA doping sites or covalent interactions with PA can effectively reduce acid leaching.Membrane oxidative degradation can be alleviated by synthesizing crosslinked or branched polymers,and introducing antioxidative groups or highly oxidative stable materials.Crosslinking to get a compact structure,blending with stable polymers and inorganic materials,preparing polymer with high molecular weight,and fabricating the polymer with PA doping sites away from backbones,are recommended to improve the membrane mechanical strength.Also,by comparing the running hours and decay rate,three current approaches,1.crosslinking via thermally curing or polymeric crosslinker,2.incorporating hygroscopic inorganic materials,3.increasing membrane layers or introducing strong basic groups and electron-withdrawing groups,have been concluded to be promising approaches to improve the durability of HT-PEMFCs.The overall aim of this review is to explore the existing degradation challenges and opportunities to serve as a solid basis for the deployment in the fuel cell market.
基金supported by the Royal Academy of Engineering,United Kingdom
文摘An extensive study has been conducted on the proton exchange membrane fuel cells (PEMFCs) with reducing Pt loading. This is commonly achieved by developing methods to increase the utilization of the platinum in the catalyst layer of the electrodes. In this paper, a novel process of the catalyst layers was introduced and investigated. A mixture of carbon powder and Nafion solution was sprayed on the glassy carbon electrode (GCE) to form a thin carbon layer. Then Pt particles were deposited on the surface by reducing hexachloroplatinic (IV) acid hexahydrate with methanoic acid. SEM images showed a continuous Pt gradient profile among the thickness direction of the catalytic layer by the novel method. The Pt nanowires grown are in the size of 3 nm (diameter) x l0 nm (length) by high solution TEM image. The novel catalyst layer was characterized by cyclic voltammetry (CV) and scanning electron microscope (SEM) as compared with commercial Pt/C black and Pt catalyst layer obtained from sputtering. The results showed that the platinum nanoparticles deposited on the carbon powder were highly utilized as they directly faced the gas diffusion layer and offered easy access to reactants (oxygen or hydrogen).
基金financially supported by the National Key Research and Development Program of China (2016YFB0101203)the National Natural Science Foundation of China (91545205,21633008)
文摘Proton exchange membranes (PEMs) are a key material for proton exchange membrane fuel cells (PEM-FCs), Non-fluorinated hydrocarbon PEMs are low-cost alternatives to Nation, but limited by the low pro-ton conductivity, because of the weak phase segregation structure and narrow ion-transport channels.Various efforts have been taken to improve the performance of hydrocarbon PEMs, but mostly with com-plex methodologies. Here we demonstrate a simple, yet very efficient method to create phase segrega-tion structure inside a typical hydrocarbon PEM, sulfonated poly(ether ether ketone) (SPEEK). By sim-ply adding appropriate amounts of water into the DMF solvent, the resulting SPEEK membrane exhibitswidened ion-transport channels, with the phase size of 2.7 nm, as indicated by both molecular dynamic(MD) simulations and transmission electron microscope (TEM) observations, and the proton conductivityis thus improved by 200%. These findings not only further our fundamental understanding of hydrocarbonPEMs, but are also valuable to the development of low-cost and practical fuel cell technologies.
基金the EPSRC grant EP/009050/1supported by the Henry Royce Institute for Advanced Materials which is funded by EPSRC grants EP/S019367/1,EP/P025021/1,EP/R00661X/1 and EP/P025498/1.
文摘Silica nanosheets(SN)derived from natural vermiculite(Verm)were successfully incorporated into polyethersulfone-polyvinylpyrrolidone(PES-PVP)polymer to fabricate high-temperature proton exchange membranes(HT-PEMs).The content of SN filler was varied(0.1-0.75 wt%)to study its influence on proton conductivity,power density and durability.Benefiting from the hydroxyl groups of SN that enable the formation of additional proton-transferring pathways,the inorganic-organic membrane displayed enhanced proton conductivity of 48.2 mS/cm and power density of 495 mW/cm^(2) at 150℃ without humidification when the content of SN is 0.25 wt%.Furthermore,exfoliated SN(E-SN)and sulfonated SN(S-SN),which were fabricated by a liquid-phase exfoliation method and silane condensation,respectively,were embedded in PES-PVP polymer matrix by a simple blending method.Due to the significant contribution from sulfonic groups in S-SN,the membrane with 0.25 wt%S-SN reached the highest proton conductivity of51.5 mS/cm and peak power density of 546 mW/cm^(2) at150℃,48%higher than the pristine PES-PVP membranes.Compared to unaltered PES-PVP membrane,SN added hybrid composite membrane demonstrated excellent durability for the fuel cell at 150℃.Using a facile method to prepare 2D SN from natural clay minerals,the strategy of exfoliation and functionalization of SN can be potentially used in the production of HT-PEMs.
基金Funded by the National Natural Science Foundation of China(Nos.51036003,50906026,20876121,and51276071)the Fundamental Research Funds for the Central Universities(2012IV084 and 2011TS079)
文摘Distribution expressions of total gas pressure and partial water vapor pressure along the channel direction were established based on lumped model by analyzing pressure loss in the channel and gas diffusion in the layer. The mechanism of droplet formation in the flow channel was also analyzed. Effects of the relative humidity, working temperature and stoichiometry on liquid water formation were discussed in detail. Moreover, the force equilibrium equation of the droplet in the flow channel was deduced, and the critical flow velocity for the water droplet removal was also addressed. The experimental results show that the threshold position of the liquid droplet is far from the inlet with the increase of temperature, and it decreases with the increase of the inlet total pressure. The critical flow velocity decreases with the increase of the radius and the working pressure.
基金The authors gratefully acknowledge the financial supports of the National Natural Science Foundation of China (No. 50273005).
文摘Novel SPPESK/PAA composite proton exchange membranes with semi-interpenetrating polymer network (sIPN) structure have been synthesized through the in-situ polymerization of acrylic acid (AA) in the presence of sulfonated poly (phthalazinone ether sulfone ketone) (SPPESK). The composite membranes were identified by FT-IR analysis. Water uptake of the composite membranes was as high as 89.7% at 90℃, nearly one time higher than that of the corresponding SPPESK membrane.
基金Project supported by the National Natural Science Foundation of China (Grant No.20576071)the Natural Science Foundation of Shanghai Municipality (Grant No.08ZR1409800)
文摘To prevent the oxygen starvation and improve the system output performance, an adaptive inverse control (AIC) strategy is developed to regulate the air supply flow of a proton exchange membrane fuel cell (PEMFC) system in this paper. The PEMFC stack and the air supply system including a compressor and a supply manifold are modeled for the purpose of performance analysis and controller design. A recurrent fuzzy neural network (RFNN) is utilized to identify the inverse model of the controlled system and generates a suitable control input during the abrupt step change of external disturbances. Compared with the PI controller, numerical simulations are performed to validate the effectiveness and advantages of the proposed AIC strategy.
基金Funded by National Natural Science Foundation of China(No.50803046)
文摘In order to improve the proton conductivity of hollow silica spheres (HSS)/perfluorosulfonic acid ion-exchange (PFSA) composite membranes as proton exchange membrane,sulfonic acid groups were grafted onto the surfaces of HSS via post grafting methods.TEM images and FT-IR spectra of the obtained sulfonic acid groups modified hollow silica spheres (SAMHSS) illustrated that the sulfonic acid groups were successfully grafted onto the surfaces of HSS.Water uptake and swelling degree of SAMHSS/PFSA composite membranes were found much higher than those of HSS/PFSA membranes due to the introduction of hydrophilic sulfonic acid groups.In a range from 50 ℃ to 130 ℃,the highest conductivity of composite membranes was obtained when 5 wt% SAMHSS was loaded.The maximum conductivity reached 7.5×10-2 S·cm-1 at 100 ℃ and 100% relative humidity,even the temperature increased to 130 ℃,the conductivity of composite membranes with 5 wt% SAMHSS could reach 3.7×10-2 S·cm-1 at 100 % relative humidity,while the conductivity of the recast PFSA was only 2.2×10-3 S·cm-1.
基金finically supported by the National Natural Science Foundation of China(22075055)the Guangxi Science and Technology Project(AB16380030)the Innovation Project of Guangxi Graduate Education(YCSW2020052)。
文摘Reducing a Pt loading with improved power output and durability is essential to promote the large-scale application of proton exchange membrane fuel cells(PEMFCs).To achieve this goal,constructing optimized structure of catalyst layers with efficient mass transportation channels plays a vital role.Herein,PEMFCs with order-structured cathodic electrodes were fabricated by depositing Pt nanoparticles by Ebeam onto vertically aligned carbon nanotubes(VACNTs)growth on Al foil via plasma-enhanced chemical vapor deposition.Results demonstrate that the proportion of hydrophilic Pt-deposited region along VACNTs and residual hydrophobic region of VANCTs without Pt strongly influences the cell performance,in particular at high current densities.When Pt nanoparticles deposit on the top depth of around 600 nm on VACNTs with a length of 4.6μm,the cell shows the highest performance,compared with others with various lengths of VACNTs.It delivers a maximum power output of 1.61 W cm^(-2)(H_(2)/O_(2),150 k Pa)and 0.79 W cm^(-2)(H_(2)/Air,150 k Pa)at Pt loading of 50μg cm^(-2),exceeding most of previously reported PEMFCs with Pt loading of<100μg cm^(-2).Even though the Pt loading is down to 30μg cm^(-2)(1.36 W cm^(-2)),the performance is also better than 100μg cm^(-2)(1.24 W cm^(-2))of commercial Pt/C,and presents better stability.This excellent performance is critical attributed to the ordered hydrophobic region providing sufficient mass passages to facilitate the fast water drainage at high current densities.This work gives a new understanding for oxygen reduction reaction occurred in VACNTs-based ordered electrodes,demonstrating the most possibility to achieve a substantial reduction in Pt loading<100μg cm^(-2) without sacrificing in performance.