The magnetization reduction of hematite using biomass waste can effectively utilize waste and reduce CO_(2) emission to achieve the goals of carbon peaking and carbon neutrality.The effects of temperatures on suspensi...The magnetization reduction of hematite using biomass waste can effectively utilize waste and reduce CO_(2) emission to achieve the goals of carbon peaking and carbon neutrality.The effects of temperatures on suspension magnetization roasting of hematite using biomass waste for evolved gases have been investigated using TG-FTIR,Py-GC/MS and gas composition analyzer.The mixture reduction process is divided into four stages.In the temperature range of 200-450℃ for mixture,the release of CO_(2),acids,and ketones is dominated in gases products.The yield and concentration of small molecules reducing gases increase when the temperature increases from 450 to 900℃.At 700℃,the volume concentrations of CO,H_(2) and CH_(4) peak at 8.91%,8.90% and 4.91%,respectively.During the suspension magnetization roasting process,an optimal iron concentrate with an iron grade of 70.86%,a recovery of 98.66% and a magnetic conversion of 45.70% is obtained at 700℃.Therefore,the magnetization reduction could react greatly in the temperature range of 600 to 700℃ owing to the suitable reducing gases.This study shows a detail gaseous evolution of roasting temperature and provides a new insight for studying the reduction process of hematite using biomass waste.展开更多
Iron and titanium were recovered from beach titanomagnetite(TTM) concentrate by embedding direct reduction and magnetic separation. The reduction products and the effects of the reductant type and reduction temperatur...Iron and titanium were recovered from beach titanomagnetite(TTM) concentrate by embedding direct reduction and magnetic separation. The reduction products and the effects of the reductant type and reduction temperature on the reduction behavior were investigated. The results showed that the reduction of TTM concentrate was strongly related to the gasification reactivity of the reductant. Bitumite presented a better product index than wheat-straw biochar and coke, mainly because the gasification reactivity of bitumite was better than that of the other reductants. In addition, high temperatures were not beneficial to embedding direct reduction because of the emergence of a molten phase and iron-joined crystals, which in turn reduced the diffusion rate of the reducing gas and impeded the reduction reaction in the central area of the roasted briquette. The use of bitumite as the reductant at a C/Fe molar ratio of 1.4 and a reduction temperature of 1200°C for 120 min resulted in direct-reduction iron powder assaying 90.28 wt% TFe and 0.91 wt% TiO_2 with an iron recovery of 91.83% and titanium concentrate assaying 46.01 wt% TiO_2 with a TiO_2 recovery of 91.19%. Titanium existed mainly in the form of anosovite and ilmenite in the titanium concentrate.展开更多
The present investigation examines the viability of dolochar, a sponge iron industry waste material, as a reductant in the reduction roasting of iron ore slimes, which are another waste generated by iron ore beneficia...The present investigation examines the viability of dolochar, a sponge iron industry waste material, as a reductant in the reduction roasting of iron ore slimes, which are another waste generated by iron ore beneficiation plants. Under statistically determined optimum conditions, which include a temperature of 900°C, a reductant-to-feed mass ratio of 0.35, and a reduction time of 30–45 min, the roasted mass, after being subjected to low-intensity magnetic separation, yielded an iron ore concentrate of approximately 64 wt% Fe at a mass recovery of approximately 71% from the feed iron ore slime assaying 56.2 wt% Fe. X-ray diffraction analyses indicated that the magnetic products contain magnetite and hematite as the major phases, whereas the nonmagnetic fractions contain quartz and hematite.展开更多
The chemiluminescence reactions between lucigenin and reductants such as Mo(LII),V( II), U(III), W(III), Cr(II), Ti(III) and Fe( II), which were produced on-line by passing Mo(VI),V(V),U(VI), W(VI), Cr(VI,III),Ti(IV) ...The chemiluminescence reactions between lucigenin and reductants such as Mo(LII),V( II), U(III), W(III), Cr(II), Ti(III) and Fe( II), which were produced on-line by passing Mo(VI),V(V),U(VI), W(VI), Cr(VI,III),Ti(IV) and Fe(III) through a micro Jones column, are studied in detail. Results show that the reactions can be used directly for the determination of these substances. The mechanism of the reactions is also investigated.展开更多
The chemiluminescence reaction between luminol and reductant was investigated by a flow-injection system. The results show that this reaction can be used for the determination of the reductant which is active to chemi...The chemiluminescence reaction between luminol and reductant was investigated by a flow-injection system. The results show that this reaction can be used for the determination of the reductant which is active to chemiluminescence in alkaline lumminol, and of the substance which can, in appropriate manner, be converted into the active reductant. The mechanism of the chemiluminescence reaction may be that the reductant reduces dissolved oxygen to O2 , then O2 reacts with alkaline luminol to generate chemiluminescence.展开更多
From atom economy of green chemistry,two principles of selecting reductant were gotten: the smaller consumption of reductant material quantity per Mole-electron,and the lighter load on environment. On the basis of the...From atom economy of green chemistry,two principles of selecting reductant were gotten: the smaller consumption of reductant material quantity per Mole-electron,and the lighter load on environment. On the basis of these two principles,experimental research was done on organic compounds. Alcohol,ketone,amine,ester,acid,and alcohol,ketone,amine were selected to act as green reductants,whose optimal process parameters were obtained. Compared with the traditional method,researched method decreases not only the amount of reductants by about 90%,but also the amount of acid medium and solid waste,where the by-products are carbon dioxide and water. The acid medium is recycled.展开更多
Presently the iron and steel makers are compelled to incorporate rational initiatives to reduce its processing CO_2 total emissions.In the medium and long term,the injection of small particles of biochar through the t...Presently the iron and steel makers are compelled to incorporate rational initiatives to reduce its processing CO_2 total emissions.In the medium and long term,the injection of small particles of biochar through the tuyerees in blast furnaces,here called Bio-PCI,offers attractive features from the environmental and metallurgical point of view,as it is a renewable carbon neutral reductant and presents lesser impurities than coke.However,its utilization in iron plants is been hindered by the traditional large availability of relatively economical coal and coke.As the cost of the principal processing inputs increases(coal,coke and iron ore) the gap between fossil and renewable reductants decreases.In this sense,our contribution aims to complement the metallurgical inquiry of technical feasibility with a strategic identification of the areas with best prospects to benefits from the incorporation of Bio-PCI:where can it flourish?.Our analysis leads to indicate that emerging countries in specific,China,Brazil and India,are in a prime position to incorporate the Bio-PCI as they simultaneously comply with a growing iron industry based on blast furnaces,and possess an important potential for energy generation from forestry residues.展开更多
The hydrometallurgical strategy of extracting Mn from low-grade Mn ores has attracted attention for the production of electrolytic manganese metal(EMM). In this work, the reductive dissolution of low-grade Mn O2 ores ...The hydrometallurgical strategy of extracting Mn from low-grade Mn ores has attracted attention for the production of electrolytic manganese metal(EMM). In this work, the reductive dissolution of low-grade Mn O2 ores using toxic nitrocellulose acidic wastewater(NAW) as a reductant was investigated for the first time. Under the optimized conditions of an Mn O2 ore dosage of 100 g·L-1, an ore particle size of-200 mesh, concentrated H2 SO4-to-NAW volume ratio of 0.12, reaction temperature of 90°C, stirring speed at 160 r·min-1, and a contact time of 120 min, the reductive leaching efficiency of Mn and the total organic carbon(TOC) removal efficiency of NAW reached 97.4% and 98.5%, respectively. The residual TOC of 31.6 mg·L-1 did not adversely affect the preparation of EMM. The current process offers a feasible route for the concurrent realization of the reductive leaching of Mn and the treatment of toxic wastewater via a simple one-step process.展开更多
NOx storage and reduction(NSR)technology has been regarded as one of the most promising strategies for the removal of nitric oxides(NOx)from lean-burn engines,and the potential of the plasma catalysis method for NOx r...NOx storage and reduction(NSR)technology has been regarded as one of the most promising strategies for the removal of nitric oxides(NOx)from lean-burn engines,and the potential of the plasma catalysis method for NOx reduction has been confirmed in the past few decades.This work reports the NSR of nitric oxide(NO)by combining non-thermal plasma(NTP)and Co/Pt/Ba/γ-Al2O3(Co/PBA)catalyst using methane as a reductant.The experimental results reveal that the NOx conversion of NSR assisted by NTP is notably enhanced compared to the catalytic efficiency obtained from NSR in the range of 150°C–350°C,and NOx conversion of the 8%Co/PBA catalyst reaches 96.8%at 350°C.Oxygen(O_(2))has a significant effect on the removal of NOx,and the NOx conversion increases firstly and then decreases when the O_(2)concentration ranges from 2%to 10%.Water vapor reduces the NOx storage capacity of Co/PBA catalysts on account of the competition for adsorption sites on the surface of Co/PBA catalysts.There is a negative correlation between sulfur dioxide(SO_(2))and NOx conversion in the NTP system,and the 8%Co/PBA catalyst exhibits higher NOx conversion compared to other catalysts,which shows that Co has a certain SO_(2)resistance.展开更多
The large consumption and discharge of diclofenac(DCF) lead to its frequent detection in surface water and groundwater, posing great threats to humans and ecosystems. This study explored the oxidation kinetics of DCF ...The large consumption and discharge of diclofenac(DCF) lead to its frequent detection in surface water and groundwater, posing great threats to humans and ecosystems. This study explored the oxidation kinetics of DCF by permanganate(Mn(Ⅶ)), and expounded the underlying reason for the unusual p Hdependency that was unclear in previous studies. The kinetics of DCF analogues(i.e., aromatic secondary amines) by Mn(Ⅶ) oxidation were comparatively investigated. Then, a tentative kinetic model involving the formation of an intermediate between Mn(Ⅶ) and DCF or its analogues was proposed to fit the p H-rate profile. Since DCF contained two chloro groups, and a carboxyl group which could be ionized by negative electrospray ionization, a precursor ionization scanning approach was used for the first time for detection of N-containing chlorinated oxidation products. New degradation pathways of DCF containing ring opening, carboxylation, carbonylation, electrophilic addition, hydroxylation and dehydrogenation were proposed based on the identified oxidation products. Moreover, it was demonstrated that the introduction of various reducing agents such as Mn(Ⅱ), Fe(Ⅱ) and bisulfite significantly improved the oxidation kinetics of DCF by Mn(Ⅶ). The positive effects of Mn(Ⅱ) and Fe(Ⅱ) were mainly attributed to the accelerated formation of MnO_(2)that acted as a catalyst or co-oxidizer contributing to DCF degradation. The presence of bisulfite caused two-stage kinetics, where a sharp drop of DCF concentration followed by a slowdown of DCF removal. In the first stage, potent reactive manganese species(e.g., Mn(Ⅲ), Mn(V), and Mn(VI)) and sulfate radical were generated during reaction of bisulfite with Mn(Ⅶ), whereas bisulfite was depleted fast due to excess Mn(Ⅶ) concentrations and the system became the Mn(Ⅶ)/MnO_(2)system in the second stage. These results provide new insight into reaction mechanism of DCF with Mn(Ⅶ)as well as propose a feasible strategy for enhancing the treatment of DCF contaminated water by Mn(Ⅶ).展开更多
Reducing the aerodynamic drag and noise levels of high-speed pantographs is important for promoting environmentally friendly,energy efficient and rapid advances in train technology.Using computational fluid dynamics t...Reducing the aerodynamic drag and noise levels of high-speed pantographs is important for promoting environmentally friendly,energy efficient and rapid advances in train technology.Using computational fluid dynamics theory and the K-FWH acoustic equation,a numerical simulation is conducted to investigate the aerodynamic characteristics of high-speed pantographs.A component optimization method is proposed as a possible solution to the problemof aerodynamic drag and noise in high-speed pantographs.The results of the study indicate that the panhead,base and insulator are the main contributors to aerodynamic drag and noise in high-speed pantographs.Therefore,a gradual optimization process is implemented to improve the most significant components that cause aerodynamic drag and noise.By optimizing the cross-sectional shape of the strips and insulators,the drag and noise caused by airflow separation and vortex shedding can be reduced.The aerodynamic drag of insulator with circular cross section and strips with rectangular cross section is the largest.Ellipsifying insulators and optimizing the chamfer angle and height of the windward surface of the strips can improve the aerodynamic performance of the pantograph.In addition,the streamlined fairing attached to the base can eliminate the complex flow and shield the radiated noise.In contrast to the original pantograph design,the improved pantograph shows a 21.1%reduction in aerodynamic drag and a 1.65 dBA reduction in aerodynamic noise.展开更多
Nitrogen electro-reduction under mild conditions is one promising alternative approach of the energyconsuming Haber-Bosch process for the artificial ammonia synthesis.One critical aspect to unlocking this technology i...Nitrogen electro-reduction under mild conditions is one promising alternative approach of the energyconsuming Haber-Bosch process for the artificial ammonia synthesis.One critical aspect to unlocking this technology is to discover the catalysts with high selectivity and efficiency.In this work,the N_(2)-to-NH_(3)conversion on the functional MoS_(2)is fully investigated by density functional theory calculations since the layered MoS_(2)provides the ideal platform for the elaborating copies of the nitrogenase found in nature,wherein the functionalization is achieved via basal-adsorption,basal-substitution or edge-substitution of transition metal elements.Our results reveal that the edge-functionalization is a feasible strategy for the activity promotion;however,the basal-adsorption and basal-substitution separately suffer from the electrochemical instability and the NRR inefficiency.Specifically,MoS_(2)functionalized via edge W-substitution exhibits an exceptional activity.The energetically favored reaction pathway is through the distal pathway and a limiting potential is less than 0.20 V.Overall,this work escalates the rational design of the high-effective catalysts for nitrogen fixation and provides the explanation why the predicated catalyst have a good performance,paving the guidance for the experiments.展开更多
In this study,we systematically investigated the effect of proton concentration on the kinetics of the oxygen reduction reaction(ORR)on Pt(111)in acidic solutions.Experimental results demonstrate a rectangular hyperbo...In this study,we systematically investigated the effect of proton concentration on the kinetics of the oxygen reduction reaction(ORR)on Pt(111)in acidic solutions.Experimental results demonstrate a rectangular hyperbolic relationship,i.e.,the ORR current excluding the effect of other variables increases with proton concentration and then tends to a constant value.We consider that this is caused by the limitation of ORR kinetics by the trace oxygen concentration in the solution,which determines the upper limit of ORR kinetics.A model of effective concentration is further proposed for rectangular hyperbolic relationships:when the reactant concentration is high enough to reach a critical saturation concentration,the effective reactant concentration will become a constant value.This could be due to the limited concentration of a certain reactant for reactions involving more than one reactant or the limited number of active sites available on the catalyst.Our study provides new insights into the kinetics of electrocatalytic reactions,and it is important for the proper evaluation of catalyst activity and the study of structureperformance relationships.展开更多
The development of modern agriculture requires the reduction of water and chemical N fertilizer inputs.Increasing the planting density can maintain higher yields,but also consumes more of these restrictive resources.H...The development of modern agriculture requires the reduction of water and chemical N fertilizer inputs.Increasing the planting density can maintain higher yields,but also consumes more of these restrictive resources.However,whether an increased maize density can compensate for the negative effects of reduced water and N supply on grain yield and N uptake in the arid irrigated areas remains unknown.This study is part of a long-term positioning trial that started in 2016.A split-split plot field experiment of maize was implemented in the arid irrigated area of northwestern China in 2020 to 2021.The treatments included two irrigation levels:local conventional irrigation reduced by 20%(W1,3,240 m^(3)ha^(-1))and local conventional irrigation(W2,4,050 m^(3)ha^(-1));two N application rates:local conventional N reduced by 25%(N1,270 kg ha^(-1))and local conventional N(360 kg ha^(-1));and three planting densities:local conventional density(D1,75,000 plants ha^(-1)),density increased by 30%(D2,97,500 plants ha-1),and density increased by 60%(D3,120,000 plants ha^(-1)).Our results showed that the grain yield and aboveground N accumulation of maize were lower under the reduced water and N inputs,but increasing the maize density by 30% can compensate for the reductions of grain yield and aboveground N accumulation caused by the reduced water and N supply.When water was reduced while the N application rate remained unchanged,increasing the planting density by 30% enhanced grain yield by 13.9% and aboveground N accumulation by 15.3%.Under reduced water and N inputs,increasing the maize density by 30% enhanced N uptake efficiency and N partial factor productivity,and it also compensated for the N harvest index and N metabolic related enzyme activities.Compared with W2N2D1,the N uptake efficiency and N partial factor productivity increased by 28.6 and 17.6%under W1N1D2.W1N2D2 had 8.4% higher N uptake efficiency and 13.9% higher N partial factor productivity than W2N2D1.W1N2D2 improved urease activity and nitrate reductase activity by 5.4% at the R2(blister)stage and 19.6% at the V6(6th leaf)stage,and increased net income and the benefit:cost ratio by 22.1 and 16.7%,respectively.W1N1D2 and W1N2D2 reduced the nitrate nitrogen and ammoniacal nitrogen contents at the R6 stage in the 40-100 cm soil layer,compared with W2N2D1.In summary,increasing the planting density by 30% can compensate for the loss of grain yield and aboveground N accumulation under reduced water and N inputs.Meanwhile,increasing the maize density by 30% improved grain yield and aboveground N accumulation when water was reduced by 20% while the N application rate remained constant in arid irrigation areas.展开更多
The electrochemical reduction of carbon dioxide offers a sound and economically viable technology for the electrification and decarbonization of the chemical and fuel industries.In this technology,an electrocatalytic ...The electrochemical reduction of carbon dioxide offers a sound and economically viable technology for the electrification and decarbonization of the chemical and fuel industries.In this technology,an electrocatalytic material and renewable energy-generated electricity drive the conversion of carbon dioxide into high-value chemicals and carbon-neutral fuels.Over the past few years,single-atom catalysts have been intensively studied as they could provide near-unity atom utilization and unique catalytic performance.Single-atom catalysts have become one of the state-of-the-art catalyst materials for the electrochemical reduction of carbon dioxide into carbon monoxide.However,it remains a challenge for single-atom catalysts to facilitate the efficient conversion of carbon dioxide into products beyond carbon monoxide.In this review,we summarize and present important findings and critical insights from studies on the electrochemical carbon dioxide reduction reaction into hydrocarbons and oxygenates using single-atom catalysts.It is hoped that this review gives a thorough recapitulation and analysis of the science behind the catalysis of carbon dioxide into more reduced products through singleatom catalysts so that it can be a guide for future research and development on catalysts with industry-ready performance for the electrochemical reduction of carbon dioxide into high-value chemicals and carbon-neutral fuels.展开更多
The sluggish kinetics of the electrochemical oxygen reduction reaction(ORR)in intermediatetemperature solid oxide fuel cells(IT-SOFCs)greatly limits the overall cell performance.In this study,an efficient and durable ...The sluggish kinetics of the electrochemical oxygen reduction reaction(ORR)in intermediatetemperature solid oxide fuel cells(IT-SOFCs)greatly limits the overall cell performance.In this study,an efficient and durable cathode material for IT-SOFCs is designed based on density functional theory(DFT)calculations by co-doping with Nb and Ta the B-site of the SrFeO_(3-δ)perovskite oxide.The DFT calculations suggest that Nb/Ta co-doping can regulate the energy band of the parent SrFeO_(3-δ)and help electron transfer.In symmetrical cells,such cathode with a SrFe_(0.8)Nb_(0.1)Ta_(0.1)O_(3-δ)(SFNT)detailed formula achieves a low cathode polarization resistance of 0.147Ωcm^(2) at 650℃.Electron spin resonance(ESR)and X-ray photoelectron spectroscopy(XPS)analysis confirm that the co-doping of Nb/Ta in SrFeO_(3-δ)B-site increases the balanced concentration of oxygen vacancies,enhancing the electrochemical performance when compared to 20 mol%Nb single-doped perovskite oxide.The cathode button cell with NiSDC|SDC|SFNT configuration achieves an outstanding peak power density of 1.3 W cm^(-2)at 650℃.Moreover,the button cell shows durability for 110 h under 0.65 V at 600℃ using wet H_(2) as fuel.展开更多
The discovery of efficient,selective,and stable electrocatalysts can be a key point to produce the largescale chemical fuels via electrochemical CO_(2) reduction(ECR).In this study,an earth-abundant and nontoxic ZnO-b...The discovery of efficient,selective,and stable electrocatalysts can be a key point to produce the largescale chemical fuels via electrochemical CO_(2) reduction(ECR).In this study,an earth-abundant and nontoxic ZnO-based electrocatalyst was developed for use in gas-diffusion electrodes(GDE),and the effect of nitrogen(N)doping on the ECR activity of ZnO electrocatalysts was investigated.Initially,a ZnO nanosheet was prepared via the hydrothermal method,and nitridation was performed at different times to control the N-doping content.With an increase in the N-doping content,the morphological properties of the nanosheet changed significantly,namely,the 2D nanosheets transformed into irregularly shaped nanoparticles.Furthermore,the ECR performance of Zn O electrocatalysts with different N-doping content was assessed in 1.0 M KHCO_(3) electrolyte using a gas-diffusion electrode-based ECR cell.While the ECR activity increased after a small amount of N doping,it decreased for higher N doping content.Among them,the N:ZnO-1 h electrocatalysts showed the best CO selectivity,with a faradaic efficiency(FE_(CO))of 92.7%at-0.73 V vs.reversible hydrogen electrode(RHE),which was greater than that of an undoped Zn O electrocatalyst(FE_(CO)of 63.4%at-0.78 V_(RHE)).Also,the N:ZnO-1 h electrocatalyst exhibited outstanding durability for 16 h,with a partial current density of-92.1 mA cm^(-2).This improvement of N:ZnO-1 h electrocatalyst can be explained by density functional theory calculations,demonstrating that this improvement of N:ZnO-1 h electrocatalyst comes from(ⅰ)the optimized active sites lowering the free energy barrier for the rate-determining step(RDS),and(ⅱ)the modification of electronic structure enhancing the electron transfer rate by N doping.展开更多
Silver-copper electrocatalysts have demonstrated effectively catalytic performance in electroreduction CO_(2) toward CH_(4),yet a revealing insight into the reaction pathway and mechanism has remained elusive.Herein,w...Silver-copper electrocatalysts have demonstrated effectively catalytic performance in electroreduction CO_(2) toward CH_(4),yet a revealing insight into the reaction pathway and mechanism has remained elusive.Herein,we construct chemically bonded Ag-Cu_(2)O boundaries,in which the complete reduction of Cu_(2)O to Cu has been strongly impeded owing to the presence of surface Ag shell.The interfacial confinement effect helps to maintain Cu^(+)sites at the Ag-Cu_(2)O boundaries.Using in situ/operando spectroscopy and theoretical simulations,it is revealed that CO_(2) is enriched at the Ag-Cu_(2)O boundaries due to the enhanced physisorption and chemisorption to CO_(2),activating CO_(2) to form the stable intermediate^(*)CO.The boundaries between Ag shell and the Cu_(2)O mediate local^(*)CO coverage and promote^(*)CHO intermediate formation,consequently facilitating CO_(2)-to-CH_(4) conversion.This work not only reveals the structure-activity relationships but also offers insights into the reaction mechanism on Ag-Cu catalysts for efficient electrocatalytic CO_(2) reduction.展开更多
Joint time–frequency analysis is an emerging method for interpreting the underlying physics in fuel cells,batteries,and supercapacitors.To increase the reliability of time–frequency analysis,a theoretical correlatio...Joint time–frequency analysis is an emerging method for interpreting the underlying physics in fuel cells,batteries,and supercapacitors.To increase the reliability of time–frequency analysis,a theoretical correlation between frequency-domain stationary analysis and time-domain transient analysis is urgently required.The present work formularizes a thorough model reduction of fractional impedance spectra for electrochemical energy devices involving not only the model reduction from fractional-order models to integer-order models and from high-to low-order RC circuits but also insight into the evolution of the characteristic time constants during the whole reduction process.The following work has been carried out:(i)the model-reduction theory is addressed for typical Warburg elements and RC circuits based on the continued fraction expansion theory and the response error minimization technique,respectively;(ii)the order effect on the model reduction of typical Warburg elements is quantitatively evaluated by time–frequency analysis;(iii)the results of time–frequency analysis are confirmed to be useful to determine the reduction order in terms of the kinetic information needed to be captured;and(iv)the results of time–frequency analysis are validated for the model reduction of fractional impedance spectra for lithium-ion batteries,supercapacitors,and solid oxide fuel cells.In turn,the numerical validation has demonstrated the powerful function of the joint time–frequency analysis.The thorough model reduction of fractional impedance spectra addressed in the present work not only clarifies the relationship between time-domain transient analysis and frequency-domain stationary analysis but also enhances the reliability of the joint time–frequency analysis for electrochemical energy devices.展开更多
Nafion as a universal polymer ionomer was widely applied for nanocatalysts electrode preparation.However,the effect of Nafion on electrocatalytic performance was often overlooked,especially for CO_(2)electrolysis.Here...Nafion as a universal polymer ionomer was widely applied for nanocatalysts electrode preparation.However,the effect of Nafion on electrocatalytic performance was often overlooked,especially for CO_(2)electrolysis.Herein,the key roles of Nafion for CO_(2)RR were systematically studied on Cu nanoparticles(NPs)electrocatalyst.We found that Nafion modifier not only inhibit hydrogen evolution reaction(HER)by decreasing the accessibility of H_(2)O from electrolyte to Cu NPs,and increase the CO_(2)concentration at electrocatalyst interface for enhancing the CO_(2)mass transfer process,but also activate CO_(2)molecule by Lewis acid-base interaction between Nafion and CO_(2)to accelerate the formation of^(*)CO,which favor of C–C coupling for boosting C_(2)product generation.Owing to these features,the HER selectivity was suppressed from 40.6%to 16.8%on optimal Cu@Nafion electrode at-1.2 V versus reversible hydrogen electrode(RHE),and as high as 73.5%faradaic efficiencies(FEs)of C_(2)products were achieved at the same applied potential,which was 2.6 times higher than that on bare Cu electrode(~28.3%).In addition,Nafion also contributed to the long-term stability by hinder Cu NPs morphology reconstruction.Thus,this work provides insights into the impact of Nafion on electrocatalytic CO_(2)RR performance.展开更多
基金Project(52022019)supported by the National Natural Science Foundation of China。
文摘The magnetization reduction of hematite using biomass waste can effectively utilize waste and reduce CO_(2) emission to achieve the goals of carbon peaking and carbon neutrality.The effects of temperatures on suspension magnetization roasting of hematite using biomass waste for evolved gases have been investigated using TG-FTIR,Py-GC/MS and gas composition analyzer.The mixture reduction process is divided into four stages.In the temperature range of 200-450℃ for mixture,the release of CO_(2),acids,and ketones is dominated in gases products.The yield and concentration of small molecules reducing gases increase when the temperature increases from 450 to 900℃.At 700℃,the volume concentrations of CO,H_(2) and CH_(4) peak at 8.91%,8.90% and 4.91%,respectively.During the suspension magnetization roasting process,an optimal iron concentrate with an iron grade of 70.86%,a recovery of 98.66% and a magnetic conversion of 45.70% is obtained at 700℃.Therefore,the magnetization reduction could react greatly in the temperature range of 600 to 700℃ owing to the suitable reducing gases.This study shows a detail gaseous evolution of roasting temperature and provides a new insight for studying the reduction process of hematite using biomass waste.
基金financially supported by the National Natural Science Foundation of China (Nos. 51474018 and 51674018)
文摘Iron and titanium were recovered from beach titanomagnetite(TTM) concentrate by embedding direct reduction and magnetic separation. The reduction products and the effects of the reductant type and reduction temperature on the reduction behavior were investigated. The results showed that the reduction of TTM concentrate was strongly related to the gasification reactivity of the reductant. Bitumite presented a better product index than wheat-straw biochar and coke, mainly because the gasification reactivity of bitumite was better than that of the other reductants. In addition, high temperatures were not beneficial to embedding direct reduction because of the emergence of a molten phase and iron-joined crystals, which in turn reduced the diffusion rate of the reducing gas and impeded the reduction reaction in the central area of the roasted briquette. The use of bitumite as the reductant at a C/Fe molar ratio of 1.4 and a reduction temperature of 1200°C for 120 min resulted in direct-reduction iron powder assaying 90.28 wt% TFe and 0.91 wt% TiO_2 with an iron recovery of 91.83% and titanium concentrate assaying 46.01 wt% TiO_2 with a TiO_2 recovery of 91.19%. Titanium existed mainly in the form of anosovite and ilmenite in the titanium concentrate.
文摘The present investigation examines the viability of dolochar, a sponge iron industry waste material, as a reductant in the reduction roasting of iron ore slimes, which are another waste generated by iron ore beneficiation plants. Under statistically determined optimum conditions, which include a temperature of 900°C, a reductant-to-feed mass ratio of 0.35, and a reduction time of 30–45 min, the roasted mass, after being subjected to low-intensity magnetic separation, yielded an iron ore concentrate of approximately 64 wt% Fe at a mass recovery of approximately 71% from the feed iron ore slime assaying 56.2 wt% Fe. X-ray diffraction analyses indicated that the magnetic products contain magnetite and hematite as the major phases, whereas the nonmagnetic fractions contain quartz and hematite.
文摘The chemiluminescence reactions between lucigenin and reductants such as Mo(LII),V( II), U(III), W(III), Cr(II), Ti(III) and Fe( II), which were produced on-line by passing Mo(VI),V(V),U(VI), W(VI), Cr(VI,III),Ti(IV) and Fe(III) through a micro Jones column, are studied in detail. Results show that the reactions can be used directly for the determination of these substances. The mechanism of the reactions is also investigated.
基金Supported by the National Natural Science Foundation of China
文摘The chemiluminescence reaction between luminol and reductant was investigated by a flow-injection system. The results show that this reaction can be used for the determination of the reductant which is active to chemiluminescence in alkaline lumminol, and of the substance which can, in appropriate manner, be converted into the active reductant. The mechanism of the chemiluminescence reaction may be that the reductant reduces dissolved oxygen to O2 , then O2 reacts with alkaline luminol to generate chemiluminescence.
文摘From atom economy of green chemistry,two principles of selecting reductant were gotten: the smaller consumption of reductant material quantity per Mole-electron,and the lighter load on environment. On the basis of these two principles,experimental research was done on organic compounds. Alcohol,ketone,amine,ester,acid,and alcohol,ketone,amine were selected to act as green reductants,whose optimal process parameters were obtained. Compared with the traditional method,researched method decreases not only the amount of reductants by about 90%,but also the amount of acid medium and solid waste,where the by-products are carbon dioxide and water. The acid medium is recycled.
文摘Presently the iron and steel makers are compelled to incorporate rational initiatives to reduce its processing CO_2 total emissions.In the medium and long term,the injection of small particles of biochar through the tuyerees in blast furnaces,here called Bio-PCI,offers attractive features from the environmental and metallurgical point of view,as it is a renewable carbon neutral reductant and presents lesser impurities than coke.However,its utilization in iron plants is been hindered by the traditional large availability of relatively economical coal and coke.As the cost of the principal processing inputs increases(coal,coke and iron ore) the gap between fossil and renewable reductants decreases.In this sense,our contribution aims to complement the metallurgical inquiry of technical feasibility with a strategic identification of the areas with best prospects to benefits from the incorporation of Bio-PCI:where can it flourish?.Our analysis leads to indicate that emerging countries in specific,China,Brazil and India,are in a prime position to incorporate the Bio-PCI as they simultaneously comply with a growing iron industry based on blast furnaces,and possess an important potential for energy generation from forestry residues.
基金financially supported by the National Natural Science Foundation of China (No. 21277012)the Nature Scientific Research Foundation of Shaanxi Provincial Education Office of China (No. 17JK0864)the Scientific Research Foundation for Ph D of Yan'an University(No. YDBK2018-10)
文摘The hydrometallurgical strategy of extracting Mn from low-grade Mn ores has attracted attention for the production of electrolytic manganese metal(EMM). In this work, the reductive dissolution of low-grade Mn O2 ores using toxic nitrocellulose acidic wastewater(NAW) as a reductant was investigated for the first time. Under the optimized conditions of an Mn O2 ore dosage of 100 g·L-1, an ore particle size of-200 mesh, concentrated H2 SO4-to-NAW volume ratio of 0.12, reaction temperature of 90°C, stirring speed at 160 r·min-1, and a contact time of 120 min, the reductive leaching efficiency of Mn and the total organic carbon(TOC) removal efficiency of NAW reached 97.4% and 98.5%, respectively. The residual TOC of 31.6 mg·L-1 did not adversely affect the preparation of EMM. The current process offers a feasible route for the concurrent realization of the reductive leaching of Mn and the treatment of toxic wastewater via a simple one-step process.
基金by the National Engineering Laboratory for Mobile Source Emission Control Technology(No.NELMS2019A13)the National Key Research and Development Project of China(No.2019YFC1805505)+2 种基金the Shanxi Province Bidding Project(No.20191101007)the Major Science and Technology Projects of Shanxi Province(No.20181102017)State Key Laboratory of Organic Geochemistry(No.SKLOG-201909)。
文摘NOx storage and reduction(NSR)technology has been regarded as one of the most promising strategies for the removal of nitric oxides(NOx)from lean-burn engines,and the potential of the plasma catalysis method for NOx reduction has been confirmed in the past few decades.This work reports the NSR of nitric oxide(NO)by combining non-thermal plasma(NTP)and Co/Pt/Ba/γ-Al2O3(Co/PBA)catalyst using methane as a reductant.The experimental results reveal that the NOx conversion of NSR assisted by NTP is notably enhanced compared to the catalytic efficiency obtained from NSR in the range of 150°C–350°C,and NOx conversion of the 8%Co/PBA catalyst reaches 96.8%at 350°C.Oxygen(O_(2))has a significant effect on the removal of NOx,and the NOx conversion increases firstly and then decreases when the O_(2)concentration ranges from 2%to 10%.Water vapor reduces the NOx storage capacity of Co/PBA catalysts on account of the competition for adsorption sites on the surface of Co/PBA catalysts.There is a negative correlation between sulfur dioxide(SO_(2))and NOx conversion in the NTP system,and the 8%Co/PBA catalyst exhibits higher NOx conversion compared to other catalysts,which shows that Co has a certain SO_(2)resistance.
基金financially supported by the program for the National Natural Science Foundation of China (Nos. 51979044,42177045 and 42107053)the Guangdong Natural Science Funds for Distinguished Young Scholar (No. 2019B151502023)+2 种基金Guangdong International Training Program for Outstanding Young Talentsthe China Postdoctoral Science Foundation (No. 2021M700878)Guangdong-Hong Kong-Macao Joint Laboratory for Contaminants Exposure and Health (No. 2020B1212030008)。
文摘The large consumption and discharge of diclofenac(DCF) lead to its frequent detection in surface water and groundwater, posing great threats to humans and ecosystems. This study explored the oxidation kinetics of DCF by permanganate(Mn(Ⅶ)), and expounded the underlying reason for the unusual p Hdependency that was unclear in previous studies. The kinetics of DCF analogues(i.e., aromatic secondary amines) by Mn(Ⅶ) oxidation were comparatively investigated. Then, a tentative kinetic model involving the formation of an intermediate between Mn(Ⅶ) and DCF or its analogues was proposed to fit the p H-rate profile. Since DCF contained two chloro groups, and a carboxyl group which could be ionized by negative electrospray ionization, a precursor ionization scanning approach was used for the first time for detection of N-containing chlorinated oxidation products. New degradation pathways of DCF containing ring opening, carboxylation, carbonylation, electrophilic addition, hydroxylation and dehydrogenation were proposed based on the identified oxidation products. Moreover, it was demonstrated that the introduction of various reducing agents such as Mn(Ⅱ), Fe(Ⅱ) and bisulfite significantly improved the oxidation kinetics of DCF by Mn(Ⅶ). The positive effects of Mn(Ⅱ) and Fe(Ⅱ) were mainly attributed to the accelerated formation of MnO_(2)that acted as a catalyst or co-oxidizer contributing to DCF degradation. The presence of bisulfite caused two-stage kinetics, where a sharp drop of DCF concentration followed by a slowdown of DCF removal. In the first stage, potent reactive manganese species(e.g., Mn(Ⅲ), Mn(V), and Mn(VI)) and sulfate radical were generated during reaction of bisulfite with Mn(Ⅶ), whereas bisulfite was depleted fast due to excess Mn(Ⅶ) concentrations and the system became the Mn(Ⅶ)/MnO_(2)system in the second stage. These results provide new insight into reaction mechanism of DCF with Mn(Ⅶ)as well as propose a feasible strategy for enhancing the treatment of DCF contaminated water by Mn(Ⅶ).
基金supported by National Natural Science Foundation of China(12372049)Science and Technology Program of China National Accreditation Service for Confor-mity Assessment(2022CNAS15)+1 种基金Sichuan Science and Technology Program(2023JDRC0062)Independent Project of State Key Laboratory of Rail Transit Vehicle System(2023TPL-T06).
文摘Reducing the aerodynamic drag and noise levels of high-speed pantographs is important for promoting environmentally friendly,energy efficient and rapid advances in train technology.Using computational fluid dynamics theory and the K-FWH acoustic equation,a numerical simulation is conducted to investigate the aerodynamic characteristics of high-speed pantographs.A component optimization method is proposed as a possible solution to the problemof aerodynamic drag and noise in high-speed pantographs.The results of the study indicate that the panhead,base and insulator are the main contributors to aerodynamic drag and noise in high-speed pantographs.Therefore,a gradual optimization process is implemented to improve the most significant components that cause aerodynamic drag and noise.By optimizing the cross-sectional shape of the strips and insulators,the drag and noise caused by airflow separation and vortex shedding can be reduced.The aerodynamic drag of insulator with circular cross section and strips with rectangular cross section is the largest.Ellipsifying insulators and optimizing the chamfer angle and height of the windward surface of the strips can improve the aerodynamic performance of the pantograph.In addition,the streamlined fairing attached to the base can eliminate the complex flow and shield the radiated noise.In contrast to the original pantograph design,the improved pantograph shows a 21.1%reduction in aerodynamic drag and a 1.65 dBA reduction in aerodynamic noise.
基金financial support from the National Natural Science Foundation of China(21503097,52130101,51701152,21806023,and 51702345)China Scholarship Council(202008320215).
文摘Nitrogen electro-reduction under mild conditions is one promising alternative approach of the energyconsuming Haber-Bosch process for the artificial ammonia synthesis.One critical aspect to unlocking this technology is to discover the catalysts with high selectivity and efficiency.In this work,the N_(2)-to-NH_(3)conversion on the functional MoS_(2)is fully investigated by density functional theory calculations since the layered MoS_(2)provides the ideal platform for the elaborating copies of the nitrogenase found in nature,wherein the functionalization is achieved via basal-adsorption,basal-substitution or edge-substitution of transition metal elements.Our results reveal that the edge-functionalization is a feasible strategy for the activity promotion;however,the basal-adsorption and basal-substitution separately suffer from the electrochemical instability and the NRR inefficiency.Specifically,MoS_(2)functionalized via edge W-substitution exhibits an exceptional activity.The energetically favored reaction pathway is through the distal pathway and a limiting potential is less than 0.20 V.Overall,this work escalates the rational design of the high-effective catalysts for nitrogen fixation and provides the explanation why the predicated catalyst have a good performance,paving the guidance for the experiments.
基金supported by the National Natural Science Foundation of China(21972131)。
文摘In this study,we systematically investigated the effect of proton concentration on the kinetics of the oxygen reduction reaction(ORR)on Pt(111)in acidic solutions.Experimental results demonstrate a rectangular hyperbolic relationship,i.e.,the ORR current excluding the effect of other variables increases with proton concentration and then tends to a constant value.We consider that this is caused by the limitation of ORR kinetics by the trace oxygen concentration in the solution,which determines the upper limit of ORR kinetics.A model of effective concentration is further proposed for rectangular hyperbolic relationships:when the reactant concentration is high enough to reach a critical saturation concentration,the effective reactant concentration will become a constant value.This could be due to the limited concentration of a certain reactant for reactions involving more than one reactant or the limited number of active sites available on the catalyst.Our study provides new insights into the kinetics of electrocatalytic reactions,and it is important for the proper evaluation of catalyst activity and the study of structureperformance relationships.
基金financial support of the National Natural Science Foundation of China(U21A20218 and 32101857)the‘Double First-Class’Key Scientific Research Project of Education Department in Gansu Province,China(GSSYLXM-02)+1 种基金the Fuxi Young Talents Fund of Gansu Agricultural University,China(Gaufx03Y10)the“Innovation Star”Program of Graduate Students in 2023 of Gansu Province,China(2023CXZX681)。
文摘The development of modern agriculture requires the reduction of water and chemical N fertilizer inputs.Increasing the planting density can maintain higher yields,but also consumes more of these restrictive resources.However,whether an increased maize density can compensate for the negative effects of reduced water and N supply on grain yield and N uptake in the arid irrigated areas remains unknown.This study is part of a long-term positioning trial that started in 2016.A split-split plot field experiment of maize was implemented in the arid irrigated area of northwestern China in 2020 to 2021.The treatments included two irrigation levels:local conventional irrigation reduced by 20%(W1,3,240 m^(3)ha^(-1))and local conventional irrigation(W2,4,050 m^(3)ha^(-1));two N application rates:local conventional N reduced by 25%(N1,270 kg ha^(-1))and local conventional N(360 kg ha^(-1));and three planting densities:local conventional density(D1,75,000 plants ha^(-1)),density increased by 30%(D2,97,500 plants ha-1),and density increased by 60%(D3,120,000 plants ha^(-1)).Our results showed that the grain yield and aboveground N accumulation of maize were lower under the reduced water and N inputs,but increasing the maize density by 30% can compensate for the reductions of grain yield and aboveground N accumulation caused by the reduced water and N supply.When water was reduced while the N application rate remained unchanged,increasing the planting density by 30% enhanced grain yield by 13.9% and aboveground N accumulation by 15.3%.Under reduced water and N inputs,increasing the maize density by 30% enhanced N uptake efficiency and N partial factor productivity,and it also compensated for the N harvest index and N metabolic related enzyme activities.Compared with W2N2D1,the N uptake efficiency and N partial factor productivity increased by 28.6 and 17.6%under W1N1D2.W1N2D2 had 8.4% higher N uptake efficiency and 13.9% higher N partial factor productivity than W2N2D1.W1N2D2 improved urease activity and nitrate reductase activity by 5.4% at the R2(blister)stage and 19.6% at the V6(6th leaf)stage,and increased net income and the benefit:cost ratio by 22.1 and 16.7%,respectively.W1N1D2 and W1N2D2 reduced the nitrate nitrogen and ammoniacal nitrogen contents at the R6 stage in the 40-100 cm soil layer,compared with W2N2D1.In summary,increasing the planting density by 30% can compensate for the loss of grain yield and aboveground N accumulation under reduced water and N inputs.Meanwhile,increasing the maize density by 30% improved grain yield and aboveground N accumulation when water was reduced by 20% while the N application rate remained constant in arid irrigation areas.
基金supported by the National Research Foundation of Korea(NRF)grant funded by the Korean government(MSIP)(NRF,2021R1C1C1013953,2022K1A4A7A04094394,2022K1A4A7A04095890)。
文摘The electrochemical reduction of carbon dioxide offers a sound and economically viable technology for the electrification and decarbonization of the chemical and fuel industries.In this technology,an electrocatalytic material and renewable energy-generated electricity drive the conversion of carbon dioxide into high-value chemicals and carbon-neutral fuels.Over the past few years,single-atom catalysts have been intensively studied as they could provide near-unity atom utilization and unique catalytic performance.Single-atom catalysts have become one of the state-of-the-art catalyst materials for the electrochemical reduction of carbon dioxide into carbon monoxide.However,it remains a challenge for single-atom catalysts to facilitate the efficient conversion of carbon dioxide into products beyond carbon monoxide.In this review,we summarize and present important findings and critical insights from studies on the electrochemical carbon dioxide reduction reaction into hydrocarbons and oxygenates using single-atom catalysts.It is hoped that this review gives a thorough recapitulation and analysis of the science behind the catalysis of carbon dioxide into more reduced products through singleatom catalysts so that it can be a guide for future research and development on catalysts with industry-ready performance for the electrochemical reduction of carbon dioxide into high-value chemicals and carbon-neutral fuels.
基金supported by the National Natural Science Foundation of China (51702039)。
文摘The sluggish kinetics of the electrochemical oxygen reduction reaction(ORR)in intermediatetemperature solid oxide fuel cells(IT-SOFCs)greatly limits the overall cell performance.In this study,an efficient and durable cathode material for IT-SOFCs is designed based on density functional theory(DFT)calculations by co-doping with Nb and Ta the B-site of the SrFeO_(3-δ)perovskite oxide.The DFT calculations suggest that Nb/Ta co-doping can regulate the energy band of the parent SrFeO_(3-δ)and help electron transfer.In symmetrical cells,such cathode with a SrFe_(0.8)Nb_(0.1)Ta_(0.1)O_(3-δ)(SFNT)detailed formula achieves a low cathode polarization resistance of 0.147Ωcm^(2) at 650℃.Electron spin resonance(ESR)and X-ray photoelectron spectroscopy(XPS)analysis confirm that the co-doping of Nb/Ta in SrFeO_(3-δ)B-site increases the balanced concentration of oxygen vacancies,enhancing the electrochemical performance when compared to 20 mol%Nb single-doped perovskite oxide.The cathode button cell with NiSDC|SDC|SFNT configuration achieves an outstanding peak power density of 1.3 W cm^(-2)at 650℃.Moreover,the button cell shows durability for 110 h under 0.65 V at 600℃ using wet H_(2) as fuel.
基金supported by the Basic Science Research Program through the National Research Foundation of Korea (NRF) (Grant Nos.2018R1A6A1A03024334,2019R1A2C1007637,2021M3I3A1082880,2021R1I1A1A01044174)the Basic Science Research Capacity Enhancement Project through Korea Basic Science Institute (Grant No.2019R1A6C1010024)。
文摘The discovery of efficient,selective,and stable electrocatalysts can be a key point to produce the largescale chemical fuels via electrochemical CO_(2) reduction(ECR).In this study,an earth-abundant and nontoxic ZnO-based electrocatalyst was developed for use in gas-diffusion electrodes(GDE),and the effect of nitrogen(N)doping on the ECR activity of ZnO electrocatalysts was investigated.Initially,a ZnO nanosheet was prepared via the hydrothermal method,and nitridation was performed at different times to control the N-doping content.With an increase in the N-doping content,the morphological properties of the nanosheet changed significantly,namely,the 2D nanosheets transformed into irregularly shaped nanoparticles.Furthermore,the ECR performance of Zn O electrocatalysts with different N-doping content was assessed in 1.0 M KHCO_(3) electrolyte using a gas-diffusion electrode-based ECR cell.While the ECR activity increased after a small amount of N doping,it decreased for higher N doping content.Among them,the N:ZnO-1 h electrocatalysts showed the best CO selectivity,with a faradaic efficiency(FE_(CO))of 92.7%at-0.73 V vs.reversible hydrogen electrode(RHE),which was greater than that of an undoped Zn O electrocatalyst(FE_(CO)of 63.4%at-0.78 V_(RHE)).Also,the N:ZnO-1 h electrocatalyst exhibited outstanding durability for 16 h,with a partial current density of-92.1 mA cm^(-2).This improvement of N:ZnO-1 h electrocatalyst can be explained by density functional theory calculations,demonstrating that this improvement of N:ZnO-1 h electrocatalyst comes from(ⅰ)the optimized active sites lowering the free energy barrier for the rate-determining step(RDS),and(ⅱ)the modification of electronic structure enhancing the electron transfer rate by N doping.
基金financially supported by the National Natural Science Foundation of China (21968020)the Natural Science Foundation of Inner Mongolia (2022MS02011 and 2023MS02014)+1 种基金the Science and Technology Projects of China Northern Rare Earth (BFXT-2022-D-0023)the Open Research Subject of Zhejiang Key Laboratory of Petrochemical Environmental Pollution Control (2021Z01)。
文摘Silver-copper electrocatalysts have demonstrated effectively catalytic performance in electroreduction CO_(2) toward CH_(4),yet a revealing insight into the reaction pathway and mechanism has remained elusive.Herein,we construct chemically bonded Ag-Cu_(2)O boundaries,in which the complete reduction of Cu_(2)O to Cu has been strongly impeded owing to the presence of surface Ag shell.The interfacial confinement effect helps to maintain Cu^(+)sites at the Ag-Cu_(2)O boundaries.Using in situ/operando spectroscopy and theoretical simulations,it is revealed that CO_(2) is enriched at the Ag-Cu_(2)O boundaries due to the enhanced physisorption and chemisorption to CO_(2),activating CO_(2) to form the stable intermediate^(*)CO.The boundaries between Ag shell and the Cu_(2)O mediate local^(*)CO coverage and promote^(*)CHO intermediate formation,consequently facilitating CO_(2)-to-CH_(4) conversion.This work not only reveals the structure-activity relationships but also offers insights into the reaction mechanism on Ag-Cu catalysts for efficient electrocatalytic CO_(2) reduction.
基金support from the National Science Foundation of China(22078190)the National Key R&D Plan of China(2020YFB1505802).
文摘Joint time–frequency analysis is an emerging method for interpreting the underlying physics in fuel cells,batteries,and supercapacitors.To increase the reliability of time–frequency analysis,a theoretical correlation between frequency-domain stationary analysis and time-domain transient analysis is urgently required.The present work formularizes a thorough model reduction of fractional impedance spectra for electrochemical energy devices involving not only the model reduction from fractional-order models to integer-order models and from high-to low-order RC circuits but also insight into the evolution of the characteristic time constants during the whole reduction process.The following work has been carried out:(i)the model-reduction theory is addressed for typical Warburg elements and RC circuits based on the continued fraction expansion theory and the response error minimization technique,respectively;(ii)the order effect on the model reduction of typical Warburg elements is quantitatively evaluated by time–frequency analysis;(iii)the results of time–frequency analysis are confirmed to be useful to determine the reduction order in terms of the kinetic information needed to be captured;and(iv)the results of time–frequency analysis are validated for the model reduction of fractional impedance spectra for lithium-ion batteries,supercapacitors,and solid oxide fuel cells.In turn,the numerical validation has demonstrated the powerful function of the joint time–frequency analysis.The thorough model reduction of fractional impedance spectra addressed in the present work not only clarifies the relationship between time-domain transient analysis and frequency-domain stationary analysis but also enhances the reliability of the joint time–frequency analysis for electrochemical energy devices.
基金financially supported by the Natural Science Foundation of Guangdong Province (2022A1515012359)the National Natural Science Foundation of China (21902121)+1 种基金the STU Scientific Research Foundation for Talents (NTF21020)the 2020 Li Ka Shing Foundation Cross-Disciplinary Research Grant (2020LKSFG09A)。
文摘Nafion as a universal polymer ionomer was widely applied for nanocatalysts electrode preparation.However,the effect of Nafion on electrocatalytic performance was often overlooked,especially for CO_(2)electrolysis.Herein,the key roles of Nafion for CO_(2)RR were systematically studied on Cu nanoparticles(NPs)electrocatalyst.We found that Nafion modifier not only inhibit hydrogen evolution reaction(HER)by decreasing the accessibility of H_(2)O from electrolyte to Cu NPs,and increase the CO_(2)concentration at electrocatalyst interface for enhancing the CO_(2)mass transfer process,but also activate CO_(2)molecule by Lewis acid-base interaction between Nafion and CO_(2)to accelerate the formation of^(*)CO,which favor of C–C coupling for boosting C_(2)product generation.Owing to these features,the HER selectivity was suppressed from 40.6%to 16.8%on optimal Cu@Nafion electrode at-1.2 V versus reversible hydrogen electrode(RHE),and as high as 73.5%faradaic efficiencies(FEs)of C_(2)products were achieved at the same applied potential,which was 2.6 times higher than that on bare Cu electrode(~28.3%).In addition,Nafion also contributed to the long-term stability by hinder Cu NPs morphology reconstruction.Thus,this work provides insights into the impact of Nafion on electrocatalytic CO_(2)RR performance.