To improve the efficiency of a CycloBio fluidized sand bed(CB FSB) in removal of dissolved wastes in recirculating aquaculture systems, the hydrodynamics of solid-liquid flow was investigated using computational fluid...To improve the efficiency of a CycloBio fluidized sand bed(CB FSB) in removal of dissolved wastes in recirculating aquaculture systems, the hydrodynamics of solid-liquid flow was investigated using computational fluid dynamics(CFD) modeling tools. The dynamic characteristics of silica sand within the CB FSB were determined using three-dimensional, unsteady-state simulations with the granular Eulerian multiphase approach and the RNG k-ε turbulence model, and the simulation results were validated using available lab-scale measurements. The bed expansion of CB FSB increased with the increase in water inflow rate in numerical simulations. Upon validation, the simulation involving 0.55 mm particles, the Gidaspow correlation for drag coefficient model and the Syamlal-O'Brien correlation for kinetic granular viscosity showed the closest match to the experimental results. The volume fraction of numerical simulations peaked as the wall was approached. The hydrodynamics of a pilot-scale CB FSB was simulated in order to predict the range of water flow to avoid the silica sand overflowing. The numerical simulations were in agreement with the experimental results qualitatively and quantitatively, and thus can be used to study the hydrodynamics of solid-liquid multiphase flow in CB FSB, which is of importance to the design, optimization, and amplification of CB FSBs.展开更多
Putting forth effort on analyzing the action of turbulent flow on the sand particles on rvier bed surface,in this paper, the interdependent relation between the size distribution of coarse sand bed load and flow stren...Putting forth effort on analyzing the action of turbulent flow on the sand particles on rvier bed surface,in this paper, the interdependent relation between the size distribution of coarse sand bed load and flow strength is studied.A theoretical calculation formula obtained gives good results in accordance with the field data.展开更多
The reaction behavior of oil sand from Inner Mongolia（China） were studied in a fluidizedbed pyrolysis process,and a comparative study was conducted on the properties of the liquid products obtained through fluidized...The reaction behavior of oil sand from Inner Mongolia（China） were studied in a fluidizedbed pyrolysis process,and a comparative study was conducted on the properties of the liquid products obtained through fluidized-bed pyrolysis of oil sand and the native bitumen obtained by solvent extraction.The results indicated that the fluidized-bed pyrolysis,a feasible carbon rejection process,can be used to upgrade oil sand.The reaction temperature and time were found to be the key operating parameters affecting the product distribution and yields in fluidized-bed pyrolysis of oil sand.The optimal temperature was 490℃ and the most suitable reaction time was 5 min.Under these operation conditions,the maximum yield of liquid product was 80wt%.In addition,the pyrolysis kinetics of oil sand at different heating rates of 5,10,20 and 30℃/min was investigated using a thermogravimetric analyzer（TGA）.展开更多
When a 2-D progressive wave train normally or obliquely approaches a vertical wall and then is normally or obliquely reflected from it, the combination of the approaching and reflected waves may result in a standing w...When a 2-D progressive wave train normally or obliquely approaches a vertical wall and then is normally or obliquely reflected from it, the combination of the approaching and reflected waves may result in a standing wave or a short-crested wave in front of the wall. This paper presents the experimental observations of sand bed configurations under the action of these water waves in front of the wall. The geometry of sand ripples under these water waves in front of the vertical wall is presented as a function of flow parameters, such as the water particle semi-excursion and the mobility number.展开更多
Background:Sand is often considered the preferred bedding material for dairy cows as it is thought to have lower bacterial counts than organic bedding materials and cows bedded on sand experience fewer cases of lamene...Background:Sand is often considered the preferred bedding material for dairy cows as it is thought to have lower bacterial counts than organic bedding materials and cows bedded on sand experience fewer cases of lameness and disease.Sand can also be efficiently recycled and reused,making it cost-effective.However,some studies have suggested that the residual organic material present in recycled sand can serve as a reservoir for commensal and pathogenic bacteria,although no studies have yet characterized the total bacterial community composition.Here we sought to characterize the bacterial community composition of a Wisconsin dairy farm bedding sand recycling system and its dynamics across several stages of the recycling process during both summer and winter using 16S rRNA gene amplicon sequencing.Results:Bacterial community compositions of the sand recycling system differed by both seasons and stage.Summer samples had higher richness and distinct community compositions,relative to winter samples.In both summer and winter samples,the diversity of recycled sand decreased with time drying in the recycling room.Compositionally,summer sand 14 d post-recycling was enriched in operational taxonomic units(OTUs)belonging to the genera Acinetobacter and Pseudomonas,relative to freshly washed sand and sand from cow pens.In contrast,no OTUs were found to be enriched in winter sand.The sand recycling system contained an overall core microbiota of 141 OTUs representing 68.45%±10.33%SD of the total bacterial relative abundance at each sampled stage.The 4 most abundant genera in this core microbiota included Acinetobacter,Psychrobacter,Corynebacterium,and Pseudomonas.Acinetobacter was present in greater abundance in summer samples,whereas Psychrobacter and Corynebacterium had higher relative abundances in winter samples.Pseudomonas had consistent relative abundances across both seasons.Conclusions:These findings highlight the potential of recycled bedding sand as a bacterial reservoir that warrants further study.展开更多
A new kind of hot sand cooling equipment with vertical spouted-fluidized bed is developed in this paper. It is similar to the traditional horizontal vibrating fluidized boiling cooler in principle but different from i...A new kind of hot sand cooling equipment with vertical spouted-fluidized bed is developed in this paper. It is similar to the traditional horizontal vibrating fluidized boiling cooler in principle but different from it in structure. The processing principle of the cooler is analyzed. The influence of main structural and processing parameters on the cooling effect and its mechanism are researched. Other characteristics of the cooler are discussed also. Experiment results show that the cooling efficiency η is equal to or larger than 83%, the temperature of output sand is less than 40℃ with the temperature of input sand is about between 80 and 90℃, and the productivity is 5t/ （h·m）展开更多
Sandwaves in the Changjiang estuary were measured with a shallow sediment profiler and an echosounder from 1978 to 1988. The data, together with grain size and bedform of sediment indicates that the bedload movement b...Sandwaves in the Changjiang estuary were measured with a shallow sediment profiler and an echosounder from 1978 to 1988. The data, together with grain size and bedform of sediment indicates that the bedload movement by rolling and saltation is of great significance to sediment transport and is the principal factor responsible for sandwave and sandbody development in the estuary. The sandwaves were found well-developed, which is related to the tidal range and the velocity of ebb current. However, the further growth is restricted by strong flood current prevailing in the estuary. Because of the significant bedload, the sandbodies shift obviously and frequently, and sometimes the exchange of position occurs between the sandbodies and tidal channels. As a result, ships are regularly forced to change their navigation course.展开更多
The effect of the coastal geometry on sand bed forms generation has been investigated for a tidal dominated area. Different hypothetical geometries of coastal channels with flat bottoms and unlimited sediment availabi...The effect of the coastal geometry on sand bed forms generation has been investigated for a tidal dominated area. Different hypothetical geometries of coastal channels with flat bottoms and unlimited sediment availability were exposed to strong oscillatory tidal currents to simulate the interaction of hydrodynamics and the bedload sediment transport. The hypothetical geometries stand for the idealization of the principal geographic features of the Infiernillo Channel, a coastal area of the Gulf of California where sandbanks and sand waves have been observed. A depth integrated hydrodynamic-numerical model and a parameterized formula to estimate the bedload sediment transport were applied coupled with a sediment conservation equation to determine the sea bottom morphodynamics. Model predictions in the Infiernillo Channel were compared to available satellite imagery. This investigation demonstrates that a vertical integrated numerical model is able to reproduce the development of incipient sand waves that exist in the Infiernillo Channel. Incipient sandbanks and shoals were also simulated. Sand waves with wavelengths of about 200 m were calculated on the same locations where sand waves actually exist. A crucial finding of this research was to show that the geometry of a shallow water basin and the presence of tidal velocity gradients associated with abrupt changes in the coastline alignment were critical in determining the sand-bed pattern generation. We demonstrate that a vertical variation of tidal currents is not necessary to generate sand waves.展开更多
Sediment sampling and longitudinal river-bottom surveys were conducted along the thalweg on the Tanana River near the city of Nenana, Alaska, USA, to provide basic information for the engineering design requirements o...Sediment sampling and longitudinal river-bottom surveys were conducted along the thalweg on the Tanana River near the city of Nenana, Alaska, USA, to provide basic information for the engineering design requirements of hydrokinetic devices to be deployed in the area. The study reach was located at approximately 64°33'50'N and 149°04'W. The Tanana is a large glacier-fed river, with open-water flow conditions from May to October. The river presents a single channel in the study area. Granulometric analyses of sediment moving near the riverbed reveals the coexistence of three distinctive types of sediment along the study reach: 1) nearly uniform fine sand;2) bimodal distributions containing fine sand and medium gravel;and 3) medium gravel. Preliminary relationships between sediment loads and discharge were developed. Dunes with small superimposed dunes were found along the reach. The basic geometric parameters (i.e., wavelength and height) of dunes were measured, and steepness was calculated. In general, dune wavelength increased with increasing discharge. Dune wavelengths ranged from 41 to 67 m, while small-dune wavelengths ranged from 13 to 16 m. Steepness increased slightly with increasing discharge.展开更多
A novel integrated water treatment facility, inner-recycling continuous sand filter, is discussed. The theory of micro-flocculation is applied in the sand-washing circulation system with continuous filtration and back...A novel integrated water treatment facility, inner-recycling continuous sand filter, is discussed. The theory of micro-flocculation is applied in the sand-washing circulation system with continuous filtration and backwashing. The design and operation parameters, which affect the performance of the filter, are discussed. The key design parameters are provided as follows: diameter of filter material is 0.7 to 1.0 mm, depth of filter bed is 0.6 m, filtration velocity is less than 12 m/h, ratio of gas to water is 9:11 and sand recycling rate is 2 to 4 mm/min.展开更多
基金supported by the 12th Five-year National Technology Support Project(2011BAD13B04)
文摘To improve the efficiency of a CycloBio fluidized sand bed(CB FSB) in removal of dissolved wastes in recirculating aquaculture systems, the hydrodynamics of solid-liquid flow was investigated using computational fluid dynamics(CFD) modeling tools. The dynamic characteristics of silica sand within the CB FSB were determined using three-dimensional, unsteady-state simulations with the granular Eulerian multiphase approach and the RNG k-ε turbulence model, and the simulation results were validated using available lab-scale measurements. The bed expansion of CB FSB increased with the increase in water inflow rate in numerical simulations. Upon validation, the simulation involving 0.55 mm particles, the Gidaspow correlation for drag coefficient model and the Syamlal-O'Brien correlation for kinetic granular viscosity showed the closest match to the experimental results. The volume fraction of numerical simulations peaked as the wall was approached. The hydrodynamics of a pilot-scale CB FSB was simulated in order to predict the range of water flow to avoid the silica sand overflowing. The numerical simulations were in agreement with the experimental results qualitatively and quantitatively, and thus can be used to study the hydrodynamics of solid-liquid multiphase flow in CB FSB, which is of importance to the design, optimization, and amplification of CB FSBs.
文摘Putting forth effort on analyzing the action of turbulent flow on the sand particles on rvier bed surface,in this paper, the interdependent relation between the size distribution of coarse sand bed load and flow strength is studied.A theoretical calculation formula obtained gives good results in accordance with the field data.
基金the financial support provided by the National Science Foundation of China (21176252)the China National Petroleum Science Research Program (2011B-2404-01)
文摘The reaction behavior of oil sand from Inner Mongolia（China） were studied in a fluidizedbed pyrolysis process,and a comparative study was conducted on the properties of the liquid products obtained through fluidized-bed pyrolysis of oil sand and the native bitumen obtained by solvent extraction.The results indicated that the fluidized-bed pyrolysis,a feasible carbon rejection process,can be used to upgrade oil sand.The reaction temperature and time were found to be the key operating parameters affecting the product distribution and yields in fluidized-bed pyrolysis of oil sand.The optimal temperature was 490℃ and the most suitable reaction time was 5 min.Under these operation conditions,the maximum yield of liquid product was 80wt%.In addition,the pyrolysis kinetics of oil sand at different heating rates of 5,10,20 and 30℃/min was investigated using a thermogravimetric analyzer（TGA）.
文摘When a 2-D progressive wave train normally or obliquely approaches a vertical wall and then is normally or obliquely reflected from it, the combination of the approaching and reflected waves may result in a standing wave or a short-crested wave in front of the wall. This paper presents the experimental observations of sand bed configurations under the action of these water waves in front of the wall. The geometry of sand ripples under these water waves in front of the vertical wall is presented as a function of flow parameters, such as the water particle semi-excursion and the mobility number.
基金funded by the Walter and Martha Renk Endowed Laboratory for Food Safety and the UW-Madison Food Research Institutesupported by a United States Department of Agriculture (USDA) National Institute of Food+1 种基金Agriculture (NIFA) Food Safety Challenge Grant#20017–68003-26500supported by a USDA NIFA Agricultural and Food Research Initiative Foundational Grant Foundation grant.#2020–67015-31576。
文摘Background:Sand is often considered the preferred bedding material for dairy cows as it is thought to have lower bacterial counts than organic bedding materials and cows bedded on sand experience fewer cases of lameness and disease.Sand can also be efficiently recycled and reused,making it cost-effective.However,some studies have suggested that the residual organic material present in recycled sand can serve as a reservoir for commensal and pathogenic bacteria,although no studies have yet characterized the total bacterial community composition.Here we sought to characterize the bacterial community composition of a Wisconsin dairy farm bedding sand recycling system and its dynamics across several stages of the recycling process during both summer and winter using 16S rRNA gene amplicon sequencing.Results:Bacterial community compositions of the sand recycling system differed by both seasons and stage.Summer samples had higher richness and distinct community compositions,relative to winter samples.In both summer and winter samples,the diversity of recycled sand decreased with time drying in the recycling room.Compositionally,summer sand 14 d post-recycling was enriched in operational taxonomic units(OTUs)belonging to the genera Acinetobacter and Pseudomonas,relative to freshly washed sand and sand from cow pens.In contrast,no OTUs were found to be enriched in winter sand.The sand recycling system contained an overall core microbiota of 141 OTUs representing 68.45%±10.33%SD of the total bacterial relative abundance at each sampled stage.The 4 most abundant genera in this core microbiota included Acinetobacter,Psychrobacter,Corynebacterium,and Pseudomonas.Acinetobacter was present in greater abundance in summer samples,whereas Psychrobacter and Corynebacterium had higher relative abundances in winter samples.Pseudomonas had consistent relative abundances across both seasons.Conclusions:These findings highlight the potential of recycled bedding sand as a bacterial reservoir that warrants further study.
文摘A new kind of hot sand cooling equipment with vertical spouted-fluidized bed is developed in this paper. It is similar to the traditional horizontal vibrating fluidized boiling cooler in principle but different from it in structure. The processing principle of the cooler is analyzed. The influence of main structural and processing parameters on the cooling effect and its mechanism are researched. Other characteristics of the cooler are discussed also. Experiment results show that the cooling efficiency η is equal to or larger than 83%, the temperature of output sand is less than 40℃ with the temperature of input sand is about between 80 and 90℃, and the productivity is 5t/ （h·m）
文摘Sandwaves in the Changjiang estuary were measured with a shallow sediment profiler and an echosounder from 1978 to 1988. The data, together with grain size and bedform of sediment indicates that the bedload movement by rolling and saltation is of great significance to sediment transport and is the principal factor responsible for sandwave and sandbody development in the estuary. The sandwaves were found well-developed, which is related to the tidal range and the velocity of ebb current. However, the further growth is restricted by strong flood current prevailing in the estuary. Because of the significant bedload, the sandbodies shift obviously and frequently, and sometimes the exchange of position occurs between the sandbodies and tidal channels. As a result, ships are regularly forced to change their navigation course.
文摘The effect of the coastal geometry on sand bed forms generation has been investigated for a tidal dominated area. Different hypothetical geometries of coastal channels with flat bottoms and unlimited sediment availability were exposed to strong oscillatory tidal currents to simulate the interaction of hydrodynamics and the bedload sediment transport. The hypothetical geometries stand for the idealization of the principal geographic features of the Infiernillo Channel, a coastal area of the Gulf of California where sandbanks and sand waves have been observed. A depth integrated hydrodynamic-numerical model and a parameterized formula to estimate the bedload sediment transport were applied coupled with a sediment conservation equation to determine the sea bottom morphodynamics. Model predictions in the Infiernillo Channel were compared to available satellite imagery. This investigation demonstrates that a vertical integrated numerical model is able to reproduce the development of incipient sand waves that exist in the Infiernillo Channel. Incipient sandbanks and shoals were also simulated. Sand waves with wavelengths of about 200 m were calculated on the same locations where sand waves actually exist. A crucial finding of this research was to show that the geometry of a shallow water basin and the presence of tidal velocity gradients associated with abrupt changes in the coastline alignment were critical in determining the sand-bed pattern generation. We demonstrate that a vertical variation of tidal currents is not necessary to generate sand waves.
文摘Sediment sampling and longitudinal river-bottom surveys were conducted along the thalweg on the Tanana River near the city of Nenana, Alaska, USA, to provide basic information for the engineering design requirements of hydrokinetic devices to be deployed in the area. The study reach was located at approximately 64°33'50'N and 149°04'W. The Tanana is a large glacier-fed river, with open-water flow conditions from May to October. The river presents a single channel in the study area. Granulometric analyses of sediment moving near the riverbed reveals the coexistence of three distinctive types of sediment along the study reach: 1) nearly uniform fine sand;2) bimodal distributions containing fine sand and medium gravel;and 3) medium gravel. Preliminary relationships between sediment loads and discharge were developed. Dunes with small superimposed dunes were found along the reach. The basic geometric parameters (i.e., wavelength and height) of dunes were measured, and steepness was calculated. In general, dune wavelength increased with increasing discharge. Dune wavelengths ranged from 41 to 67 m, while small-dune wavelengths ranged from 13 to 16 m. Steepness increased slightly with increasing discharge.
文摘A novel integrated water treatment facility, inner-recycling continuous sand filter, is discussed. The theory of micro-flocculation is applied in the sand-washing circulation system with continuous filtration and backwashing. The design and operation parameters, which affect the performance of the filter, are discussed. The key design parameters are provided as follows: diameter of filter material is 0.7 to 1.0 mm, depth of filter bed is 0.6 m, filtration velocity is less than 12 m/h, ratio of gas to water is 9:11 and sand recycling rate is 2 to 4 mm/min.
