A strength reduction method based on double reduction parameters and its application

In the traditional strength reduction method,the cohesion and the friction angle adopt the same reduction parameter,resulting in equivalent proportional reduction.This method does not consider the different effects of the cohesion and friction angle on the stability of the same slope and is defective to some extent.Regarding this defect,a strength reduction method based on double reduction parameters,which adopts different reduction parameters,is proposed.The core of the double-parameter reduction method is the matching reduction principle of the slope with different angles.This principle is represented by the ratio of the reduction parameter of the cohesion to that of the friction angle,described as η.With the increase in the slopeangle,ηincreases; in particular,when the slope angle is 45°,tηis 1.0.Through the matching reduction principle,different safety margin factors can be calculated for the cohesion and friction angle.In combination with these two safety margin factors,a formula for calculating the overall safety factor of the slope is proposed,reflecting the different contributions of the cohesion and friction angle to the slope stability.Finally,it is shown that the strength reduction method based on double reduction parameters acquires a larger safety factor than the classic limit equilibrium method,but the calculation results are very close to those obtained by the limit equilibrium method.

Limit analysis of vertical anti-pulling screw pile group under inclined loading on 3D elastic-plastic finite element strength reduction method

Based on the functional theory, catastrophe theory, simultaneity principle and the idea of strength reduction method （SRM）, the bearing capacity functional anti SRM of pile group foundation were established, and the criteria of ultimate load and the concept of safety storage coefficient （Css） were advanced. The inclined ultimate loads by the static loading test, load increment method （LIM） and SRM are compared. Theoretically, the ultimate load of piles does not change with the loading levels when it is calculated by SRM. When the one strength reduction parameter is applied in the calculation boundary, there are calculating errors because the bearing capacity action of soils happened in the finite zone. The inclined 10adings are 108, 132 and 144 kN, and SSC are 1.07, 0.94 and 0.79, respectively, so the calculation values of ultimate loads are about 115.56, 124.08 and 113.76 kN, respectively. The error between calculations and observation values is less than 6%. But .the error between calculations of LIM and observations is 20%. Because of the effect of inclined loading, the push-rotation phenomenon of screw pile group appears. Under this testing, the ultimate bearing capacity of piles is mostly determined by the horizontal ultimate bearing capacity, and the effect of the vertical component of inclined load should also be considered.

Strength reduction method for slope based on a ubiquitous-joint criterion and its application

In order to expand the application of strength reduction methods with the ubiquitous-joint criterion, the corresponding program is compiled using FLAC3D software. A procedure for strength reduction in the ubiquitous-joint criterion is proposed to study the safety factor of slopes as well as the relationships of the bedding plane inclination angle β and the safety factor F. The results show that： 1） for the bedding rock slope, the various failure modes cause different variations of the safety factor F; 2） a bed- ding rock slope can be divided into two types by the angle between the bedding plane inclination and slope surface inclination a; when a_〈45~, the bedding slope can be strictly defined as the subsequent bedding rock slope; when 45°〈α〈90°, the bedding slope is defined as an oblique bedding slope; 3） for bedding rock slopes, the safety factor increases with an increase in a; for inverse bed- ding slopes, when the bedding plane inclination angle fl is small, the safety factor F of the slope increases at first, then decreases with an increase in a; when β is large, the safety factor F increases with an increase in α.

Slope analysis based on local strength reduction method and variable-modulus elasto-plastic model

Employing an ideal elasto-plastic model,the typically used strength reduction method reduced the strength of all soil elements of a slope.Therefore,this method was called the global strength reduction method(GSRM).However,the deformation field obtained by GSRM could not reflect the real deformation of a slope when the slope became unstable.For most slopes,failure occurs once the strength of some regional soil is sufficiently weakened; thus,the local strength reduction method(LSRM)was proposed to analyze slope stability.In contrast with GSRM,LSRM only reduces the strength of local soil,while the strength of other soil remains unchanged.Therefore,deformation by LSRM is more reasonable than that by GSRM.In addition,the accuracy of the slope's deformation depends on the constitutive model to a large degree,and the variable-modulus elasto-plastic model was thus adopted.This constitutive model was an improvement of the Duncan–Chang model,which modified soil's deformation modulus according to stress level,and it thus better reflected the plastic feature of soil.Most importantly,the parameters of the variable-modulus elasto-plastic model could be determined through in-situ tests,and parameters determination by plate loading test and pressuremeter test were introduced.Therefore,it is easy to put this model into practice.Finally,LSRM and the variable-modulus elasto-plastic model were used to analyze Egongdai ancient landslide.Safety factor,deformation field,and optimal reinforcement measures for Egongdai ancient landslide were obtained based on the proposed method.

Application of strength reduction method to dynamic anti-sliding stability analysis of high gravity dam with complex dam foundation

Considering that there are some limitations in analyzing the anti-sliding seismic stability of dam-foundation systems with the traditional pseudo-static method and response spectrum method, the dynamic strength reduction method was used to study the deep anti-sliding stability of a high gravity dam with a complex dam foundation in response to strong earthquake-induced ground action. Based on static anti-sliding stability analysis of the dam foundation undertaken by decreasing the shear strength parameters of the rock mass in equal proportion, the seismic time history analysis was carried out. The proposed instability criterion for the dynamic strength reduction method was that the peak values of dynamic displacements and plastic strain energy change suddenly with the increase of the strength reduction factor. The elasto-plastic behavior of the dam foundation was idealized using the Drucker-Prager yield criterion based on the associated flow rule assumption. The result of elasto-plastic time history analysis of an overflow dam monolith based on the dynamic strength reduction method was compared with that of the dynamic linear elastic analysis, and the reliability of elasto-plastic time history analysis was confirmed. The results also show that the safety factors of the dam-foundation system in the static and dynamic cases are 3.25 and 3.0, respectively, and that the F2 fault has a significant influence on the anti-sliding stability of the high gravity dam. It is also concluded that the proposed instability criterion for the dynamic strength reduction method is feasible.

A case study of multi-seam coal mine entry stability analysis with strength reduction method

In this paper,the advantage of using numerical models with the strength reduction method(SRM) to evaluate entry stability in complex multiple-seam conditions is demonstrated.A coal mine under variable topography from the Central Appalachian region is used as a case study.At this mine,unexpected roof conditions were encountered during development below previously mined panels.Stress mapping and observation of ground conditions were used to quantify the success of entry support systems in three room-and-pillar panels.Numerical model analyses were initially conducted to estimate the stresses induced by the multiple-seam mining at the locations of the affected entries.The SRM was used to quantify the stability factor of the supported roof of the entries at selected locations.The SRM-calculated stability factors were compared with observations made during the site visits,and the results demonstrate that the SRM adequately identifies the unexpected roof conditions in this complex case.It is concluded that the SRM can be used to effectively evaluate the likely success of roof supports and the stability condition of entries in coal mines.

A New Criterion for Defining Inhomogeneous Slope Failure Using the Strength Reduction Method

A new variational method treating the system as a whole with rigorous mathematical and physical derivation was presented in this paper.Combined with classical and engineering examples,variational energy expressions of slopes were derived.In addition,the calculation programs were written in the FISH language set in FLAC3D(fast Lagrangian analysis of continua in three dimensions)software.Factors of safety(FOSs)of the models were determined by the variational method based on the strength reduction method(SRM)and then compared with other criteria or methods.The result showed that the variational method reflected the process of slope plasticity and failure uniformly and was feasible to analyze the stability of inhomogeneous slopes.The method was applicable to both two-dimensional and three-dimensional heterogeneous slopes.The small error with other criteria or methods also showed the accuracy of this method.This method unified other criteria,avoided the artificial error of other criteria,and provided a logical derivation for the instability of heterogeneous slope.This method considered the system as a whole and avoided the shortcomings of the general method of one-sided instability analysis.The proposed method is of great significance as it considers the coupling effect of stress and strain of materials and gives the mechanical basis for the instability of complex slopes.

New method of designing anti-slide piles——the strength reduction FEM

At present,the thrust of an anti-slide pile can be worked out with some calculation methods. However,the resistance in front of the pile,the distributions of resistance and thrust,and appropriate pile length cannot be easily obtained. In this paper,the authors applied the strength-reduction finite element method (FEM) to several design cases of anti-slide piles. Using this method,it is possible to take the pile-soil interactions into consideration,obtain reasonable resistance in front of pile and the distributions of thrust and resistance,and reasonable lengths of anti-slide piles. In particular,the thrust and resistance imposed on embedded anti-slide piles can be calculated and composite anti-slide pile structures such as anchored piles and braced piles can be optimized. It is proved through the calculation examples that this method is more reliable and economical in the design of anti-slide pile.

A new double reduction method for slope stability analysis

The core of strength reduction method(SRM) involves finding a critical strength curve that happens to make the slope globally fail and a definition of factor of safety(FOS). A new double reduction method, including a detailed calculation procedure and a definition of FOS for slope stability was developed based on the understanding of SRM. When constructing the new definition of FOS, efforts were made to make sure that it has concise physical meanings and fully reflects the shear strength of the slope. Two examples, slopes A and B with the slope angles of 63° and 34° respectively, were given to verify the method presented. It is found that, for these two slopes, the FOSs from original strength reduction method are respectively 1.5% and 38% higher than those from double reduction method. It is also found that the double reduction method predicts a deeper potential slide line and a larger slide mass. These results show that on one hand, the double reduction method is comparative to the traditional methods and is reasonable, and on the other hand, the original strength reduction method may overestimate the safety of a slope. The method presented is advised to be considered as an additional option in the practical slope stability evaluations although more useful experience is required.

Upper bound analysis of slope stability with nonlinear failure criterion based on strength reduction technique

Based on the upper bound limit analysis theorem and the shear strength reduction technique, the equation for expressing critical limit-equilibrium state was employed to define the safety factor of a given slope and its corresponding critical failure mechanism by means of the kinematical approach of limit analysis theory. The nonlinear shear strength parameters were treated as variable parameters and a kinematically admissible failure mechanism was considered for calculation schemes. The iterative optimization method was adopted to obtain the safety factors. Case study and comparative analysis show that solutions presented here agree with available predictions when nonlinear criterion reduces to linear criterion, and the validity of present method could be illuminated. From the numerical results, it can also be seen that nonlinear parameter rn, slope foot gradient ,β, height of slope H, slope top gradient a and soil bulk density γ have significant effects on the safety factor of the slope.

Reinforcement strength reduction in FEM for mechanically stabilized earth structures

The factor of safety of mechanically stabilized earth(MSE) structures can be analyzed either using limit equilibrium method(LEM) or strength reduction method(SRM) in finite element/difference method. In LEM, the strengths of the reinforcement members and soils are reduced with the same factor. While using the SRM, only soil strength is reduced during the calculation of the factor of safety. This causes inconsistence in calculating the factor of safety of the MSE structures. To overcome this, an iteration method is proposed to consider the strength reduction of the reinforcements in SRM. The method is demonstrated by using PLAXIS, a finite element software. The results show that the factor of safety converges after a few iterations. The reduction of strength has different effects on the factor of safety depending on the properties of the reinforcements and the soil, and failure modes.

Application of dynamic analysis of strength reduction in the slope engineering under earthquake

At present,the methods of analyzing the stability of slope under earthquake are not accurate and reasonable because of some limitations. Based on the real dynamic tensile-shear failure mechanism of slope,the paper proposes dynamic analysis of strength reduction FEM (finite element method) and takes the reduction of shear strength parameters and tensile strength parameters into consideration. And it comprehensively takes the transfixion of the failure surface,the non-convergence of calculation and mutation of displacement as the criterion of dynamic instability and failure of the slope. The strength reduction factor under limit state is regarded as the dynamic safety factor of the slope under earthquake effect and its advantages are introduced. Finally,the method is applied in the seismic design of anchors supporting and anti-slide pile supporting of the slope. Calculation examples show that the application of dynamic analysis of strength reduction is feasible in the seismic design of slope engineering,which can consider dynamic interaction of supporting structure and rock-soil mass. Owing to its preciseness and great advantages,it is a new method in the seismic design of slope supporting.

Optimal mining sequence for coal faces under a bedding slope:insight from landslide prevention

Repetitive mining beneath bedding slopes is identified as a critical factor in geomorphic disturbances, especially landslides and surface subsidence. Prior research has largely concentrated on surface deformation in plains due to multi-seam coal mining and the instability of natural bedding slopes, yet the cumulative impact of different mining sequences on bedding slopes has been less explored. This study combines drone surveys and geological data to construct a comprehensive three-dimensional model of bedding slopes. Utilizing FLAC3D and PFC2D models, derived from laboratory experiments, it simulates stress, deformation, and failure dynamics of slopes under various mining sequences. Incorporating fractal dimension analysis, the research evaluates the stability of slopes in relation to different mining sequences. The findings reveal that mining in an upslope direction minimizes disruption to overlying strata. Initiating extraction from lower segments increases tensile-shear stress in coal pillar overburdens, resulting in greater creep deformation towards the downslope than when starting from upper segments, potentially leading to localized landslides and widespread creep deformation in mined-out areas. The downslope upward mining sequence exhibits the least fractal dimensions, indicating minimal disturbance to both strata and surface. While all five mining scenarios maintain good slope stability under normal conditions, recalibrated stability assessments based on fractal dimensions suggest that downslope upward mining offers the highest stability under rainfall, contrasting with the lower stability and potential instability risks of upslope downward mining. These insights are pivotal for mining operations and geological hazard mitigation in multi-seam coal exploitation on bedding slopes.

Safety Length Simulation of Natural Gas Pipeline Subjected to Transverse Landslide

The safety of natural gas pipeline is often severely threatened by the transverse landslide. At home and abroad, it is the first time to study the safe length of the pipeline when affected by landslide, and take the safe length of the pipeline as an engineering practical index. Therefore, it is of great significance to study the influence of transverse landslide affecting the safety of natural gas pipeline when a certain length of pipeline is thrusted, and to establish practical index and simulation method for prediction and prevention of the landslide hazards to gas pipeline. Based on the current research results, this study could be divided into three steps: First of all, with the help of ANSYS finite element software, the model of transverse landslide acting on the gas pipeline can be set up, then the length value of gas pipeline safely withstanding transverse landslide can be calculated;Secondly, using the strength reduction method, which is commonly used in the research of landslide stability, can establish three-dimensional model of the landslide and pipes in the ABAQUS finite element software, next, under the same landslide pushed length, the calculation results will be obtained;Finally, to draw reliable conclusions, all calculated results of the former two methods will be linked to synthetically and comparatively analyze, then the length value of common X80 gas pipeline safely bearing transverse landslide can be got. All results can provide some references for engineering and design.

Simulation analysis on three-dimensional slope failure under different conditions

The failure mechanism of two-dimensional（2D） and three-dimensional（3D） slopes were investigated by using the strength reduction method.An extensive study of 3D effect was conducted with respect to boundary conditions,shear strength and concentrated surcharge load.The results obtained by 2D and 3D analyses were compared and the applicable scope of 2D and 3D method was analyzed.The results of the numerical simulation show that 3D effect is sensitive to the width of slip surface.As for slopes with specific geometry,3D effect is influenced by dimensionless parameter c/（γHtanφ）.For those infinite slopes with local loading,external load has the major impact on failure mode.For those slopes with local loading and geometric constraints,the failure mode is influenced by both factors.With the increase of loading length,boundary condition exerts a more significant impact on the failure mode,and then 2D and 3D stability charts are developed,which provides a rapid and reliable way to calculate 2D and 3D factor of safety without iteration.Finally,a simple and practical calculation procedure based on the study of 3D effect and stability charts is proposed to recognize the right time to apply 2D or 3D method.

Study on embedded length of piles for slope reinforced with one row of piles

The embedded length of anti-slide piles for slope is analyzed by three-dimensional elastoplastic shear strength reduction method. The effect of embedded pile length on the factor of safety and pile behavior is analyzed. Furthermore, the effects of pile spacing, pile head conditions, pile bending stiffness and soil properties on length and behavior of pile are also analyzed. The results show that the pile spacing and the pile head conditions have significant influences on the critical embedded length of pile. It is found that the critical embedded length of pile, beyond which the factor of safety does not increase, increases with the decrease in pile spacing. The smaller the pile spacing is, the larger the integrity of the reinforced slope will be. A theoretical analysis of the slip surface is also conducted, and the slip surface determined by the pressure on piles, considering the influences of both soil and piles for slope, is in agreement with the ones in previous studies.

Study on the FEM design of reinforced earth retaining wall with geogrid

At present,limit equilibrium method is often adopted in the design of reinforced earth retaining wall. Geotechnical engineers home and abroad have done a lot of work to improve the traditional calculation methods in recent years,while there are lots of defects. This paper first identifies the location of failure surface and safety factor through the finite element program of PLAXIS and then analyses the influencing factors of the stability of reinforced earth retaining wall with geogrid. The authors adopt strength reduction FEM (finite element method)in the design and stability analysis of reinforced earth retaining wall and have achieved some satisfying results. Without any assumptions,the new design method can automatically judge the failure mode of reinforced earth retaining wall,consider the influence of axial tensile stiffness of the reinforcement stripe on the stability of retaining wall,identify reasonable distance and length of the reinforcement stripe,and choose suitable parameters of reinforcement stripe,including strength,stiffness and pseudo-friction coefficient which makes the design optimal. It is proved through the calculation examples that this method is more reasonable,reliable and economical in the design of reinforced earth retaining wall.

Fluid–solid coupling analysis of rock pillar stability for concealed karst cave ahead of a roadway based on catastrophic theory

In order to study the mechanism of water inrush from a concealed, confined karst cave, we established a fluid–solid coupling model of water inrush from a concealed karst cave ahead of a roadway and a strength reduction method in a rock pillar for preventing water inrush based on catastrophic theory. Fluid–solid coupling effects and safety margins in a rock pillar were studied. Analysis shows that rock pillar instability, exerted by disturbance stress and seepage stress, is the process of rock pillar catastrophic destabilization induced by nonlinear extension of plastic zones in the rock pillar. Seepage flow emerges in the rock pillar for preventing water inrush, accompanied by mechanical instability of the rock pillar. Taking the accident of a confined karst cave water-inrush of Qiyi Mine as an example, by studying the safety factor of the rock pillar and the relationship between karst cave water pressure and thickness of the rock pillar,it is proposed that rock pillar thickness with a safety factor equal to 1.5 is regarded as the calculated safety thickness of the rock pillar, which should be equal to the sum of the blasthole depth, blasting disturbance depth and the calculated safety thickness of the rock pillar. The cause of the karst water inrush at Qiyi Mine is that the rock pillar was so small that it did not possess a safety margin. Combining fluid–solid coupling theory, catastrophic theory and strength reduction method to study the nonlinear mechanical response of complicated rock engineering, new avenues for quantitative analysis of rock engineering stability evaluation should be forthcoming.

Finite element analysis of slope stability by expanding the mobilized principal stress Mohr's circles-Development, encoding and validation

In recent years,finite element analysis is increasingly being proposed in slope stability problems as a competitive method to traditional limit equilibrium methods(LEMs)which are known for their inherent deficiencies.However,the application of finite element method(FEM)to slope stability as a strength reduction method(SRM)or as finite element limit analysis(FELA)is not always a success for the drawbacks that characterize both methods.To increase the performance of finite element analysis in this problem,a new approach is proposed in this paper.It consists in gradually expanding the mobilized stress Mohr’s circles until the soil failure occurs according to a prescribed non-convergence criterion.The present approach called stress deviator increasing method(SDIM)is considered rigorous for three main reasons.Firstly,it preserves the definition of the factor of safety(FOS)as the ratio of soil shear strength to the mobilized shear stress.Secondly,it maintains the progressive development of shear stress resulting from the increase in the principal stress deviator on the same plane,on which the shear strength takes place.Thirdly,by introducing the concept of equivalent stress loading,the resulting trial stresses are checked against the violation of the actual yield criterion formed with the real strength parameters rather than those reduced by a trial factor.The new numerical procedure was encoded in a Fortran computer code called S^(4)DINA and verified by several examples.Comparisons with other numerical methods such as the SRM,gravity increasing method(GIM)or even FELA by assessing both the FOS and contours of equivalent plastic strains showed promising results.

Study on high and steep slope stability of surface mine based on RFPA-SRM

The instability and failure mechanism of high and steep slopes in surface mines, and the basis for some reasonable landslide prevention measures were provided using the RFPA-SRM. Based on the actual progress of the Pingzhuang Western Surface Mine and based on strength reduction method, the dynamic instability processes of the top high and steep slope was simulated. Also, the landslide mode was determined, the characteristics of the displacement distribution, the deformation, failure, and the stress distribution in the slope were demonstrated, and the stability was calculated. Conclusions can be drawn as follows： the landslide or failure of high and steep slopes on a surface mine is a gradual process, in which the slope undergoes the generation, expansion, and connection of the fractures and the displacement increases until landslide occurs; a small portion of the upper rocks fail due to the tension and the lower rocks fail due to the shear; the potential sliding surface is combined and the essential cause of the landslide is the shear stress concentration.