The Youth’s View of Marriage in Chinese Mainstream Media Discourse-A Corpus-assisted Three-dimensional Discourse Analysis

The rising of aging and the declining of birth rates have forced the public to focus on the youth’s view on marriage.Based on critical discourse analysis and combined with Fairclough’s three-dimensional discourse analysis model,this paper builds a“Chinese media News Report Corpus on the topic of‘marriage’”whose news are collected from China Daily.It is found that the discourses are neutral and objective with regard to the advantages and disadvantages of marriage,but in general,it is still a traditional view of marriage that is inevitable and closely related to fertility.Although this is controlled by the policies and the social reasons including declining fertility rate,it deviates from the current view of the youth towards marriage,resulting in many serious consequences such as young people’s rejection.In addition,this research found that male and female have great differences in their views on marriage,and men’s resistance to marriage is far greater than that of women,which is departure from the public’s cognition.The reasons behind this need to be explored in order to solve the marriage and love problems of young people in today’s era and realize the healthy development of young marriage.

Influence of sampling on three-dimensional surface shape measurement

In order to accurately measure an object’s three-dimensional surface shape,the influence of sampling on it was studied.First,on the basis of deriving spectra expressions through the Fourier transform,the generation of CCD pixels was analyzed,and its expression was given.Then,based on the discrete expression of deformation fringes obtained after sampling,its Fourier spectrum expression was derived,resulting in an infinitely repeated"spectra island"in the frequency domain.Finally,on the basis of using a low-pass filter to remove high-order harmonic components and retaining only one fundamental frequency component,the inverse Fourier transform was used to reconstruct the signal strength.A method of reducing the sampling interval,i.e.,reducing the number of sampling points per fringe,was proposed to increase the ratio between the sampling frequency and the fundamental frequency of the grating.This was done to reconstruct the object’s surface shape more accurately under the condition of m>4.The basic principle was verified through simulation and experiment.In the simulation,the sampling intervals were 8 pixels,4 pixels,2 pixels,and 1 pixel,the maximum absolute error values obtained in the last three situations were 88.80%,38.38%,and 31.50%in the first situation,respectively,and the corresponding average absolute error values are 71.84%,43.27%,and 32.26%.It is demonstrated that the smaller the sampling interval,the better the recovery effect.Taking the same four sampling intervals in the experiment as in the simulation can also lead to the same conclusions.The simulated and experimental results show that reducing the sampling interval can improve the accuracy of object surface shape measurement and achieve better reconstruction results.

Shape Analysis of Agricultural Parcels for Land Consolidation Priorities in Tekirdag Province,Turkey

Shape irregularity,a sub-factor of parcel fragmentation is a problem that hinders sustainable agriculture and is solved using land consolidation projects.Determination of the parcel shape degree contributes significantly to spatial prioritization where there is also a high probability of achieving positive effects of consolidation projects.This study aims to determine the shape degree of the agricultural parcels both at singular and rural county scales in Tekirdag Province,Turkey in 2020 by combining the parcel shape index(PSI) with the minimum bounding geometry index(MBG) to improve parcel scores.Hot-spot zones of the highly irregular and near optimum parcels were also determined using Getis-Ord G_(i)^(*) statistic.The parcel degrees were classified into four categories,namely highly irregular,irregular,regular and near optimum.The obtained unweighted scores of the parameters exhibit deviations from the expected values.After weighting by pairwise comparison,the values approached ideal scores.Among 346 740 parcels,53% were highly irregular and irregular and 47% were regular and near optimum shapes after weighting whereas these were 70% and 30%,respectively before weighting.The average parcel degree of 63 rural counties was regular while the average parcel degree of the remaining 264 rural counties was irregular.The combined use of PSI and MBG index improved the correctness of the parcel shape score.It could be suggested to use as a tool in land consolidation prioritization.

Importance of Three-Dimensional Piezoelectric Coupling Modeling in Quantitative Analysis of Piezoelectric Actuators

This paper demonstrates the importance of three-dimensional(3-D)piezoelectric coupling in the electromechanical behavior of piezoelectric devices using three-dimensional finite element analyses based on weak and strong coupling models for a thin cantilevered piezoelectric bimorph actuator.It is found that there is a significant difference between the strong and weak coupling solutions given by coupling direct and inverse piezoelectric effects(i.e.,piezoelectric coupling effect).In addition,there is significant longitudinal bending caused by the constraint of the inverse piezoelectric effect in the width direction at the fixed end(i.e.,3-D effect).Hence,modeling of these effects or 3-D piezoelectric coupling modeling is an electromechanical basis for the piezoelectric devices,which contributes to the accurate prediction of their behavior.

Application of three-dimensional speckle tracking technique in measuring left ventricular myocardial function in patients with diabetes

BACKGROUND Diabetic cardiomyopathy is considered as a chronic complication of diabetes mellitus(DM).Therefore,early detection of left ventricular systolic function(LVSF)damage in DM is essential.AIM To explore the use of the three-dimensional speckle tracking technique(3D-STI)for measuring LVSF in DM patients via meta-analysis.METHODS The electronic databases were retrieved from the initial accessible time to 29 April 2023.The current study involved 9 studies,including 970 subjects.We carried out this meta-analysis to estimate myocardial function in DM compared with controls according to myocardial strain attained by 3D-STI.RESULTS Night articles including 970 subjects were included.No significant difference was detected in the left ventricular ejection fraction between the control and the diabetic group(P>0.05),while differences in global longitudinal strain,global circumferential strain,global radial strain,and global area strain were markedly different between the controls and DM patients(all P<0.05).CONCLUSION The 3D-STI could be applied to accurately measure early LVSF damage in patients with DM.

Discourse Analysis of the Belt and Road Initiative From the Perspective of Central Asian Countries: A Case Study of the Republic of Kazakhstan

This study employs Norman Fairclough’s Critical Discourse Analysis(CDA)three-dimensional model,using the Republic of Kazakhstan as a case study,to delve into the discourse construction of China’s Belt and Road Initiative(BRI)in Central Asian countries.Through detailed analysis of policy documents,media reports,and public discussions in Central Asian countries,this paper reveals how the BRI constructs specific social practices,discourse events,and textual meanings within these nations.The findings indicate that through this global development strategy,China has not only strengthened its economic ties with Central Asian countries but has also exerted profound influences on political,cultural,and social levels.

Three-dimensional analysis of slopes reinforced with piles

Based on the upper bound of limit analysis, the plane-strain analysis of the slopes reinforced with a row of piles to the 3D case was extended. A 3D rotational failure mechanism was adopted to yield the upper bound of the factor of safety. Parametric studies were carried out to explore the end effects of the slope failures and the effects of the pile location and diameter on the safety of the reinforced slopes. The results demonstrate that the end effects nearly have no effects on the most suitable location of the installed piles but have significant influence on the safety of the slopes. For a slope constrained to a narrow width, the slope becomes more stable owing to the contribution of the end effects. When the slope is reinforced with a row of piles in small space between piles, the effects of group piles are significant for evaluating the safety of slopes. The presented method is more appropriate for assessing the stability of slopes reinforced with piles and can be also utilized in the design of plies stabilizing the unstable slopes.

Three-dimensional finite element analysis on effects of tunnel construction on nearby pile foundation

A three-dimensional finite element simulation was carried out to investigate the effects of tunnel construction on nearby pile foundation.The displacement controlled model (DCM) was used to simulate the tunneling-induced volume loss effects.The numerical model was verified based on the results of a centrifuge test and a set of parametric studies was implemented based on this model.There is good agreement between the trend of the results of the centrifuge test and the present model.The results of parametric studies show that the tunnelling-induced pile internal force and deformation depend mainly on the pile?tunnel distance,the pile length to tunnel depth ratio and the volume loss.Two different zones are separated by a 45° line projected from the tunnel springline.Within the zone of influence,the pile is subjected to tensile force and large settlement;whereas outside the zone of influence,dragload and small settlement are induced.It is also established that the impact of tunnelling on a pile group is substantially smaller as compared with a single pile in the same location with the rear pile in a group,demonstrating a positive pile group effect.

Validation and application of three-dimensional discontinuous deformation analysis with tetrahedron finite element meshed block

In the last decade, three dimensional discontin- uous deformation analyses （3D DDA） has attracted more and more attention of researchers and geotechnical engineers worldwide. The original DDA formulation utilizes a linear displacement function to describe the block movement and deformation, which would cause block expansion under rigid body rotation and thus limit its capability to model block de- formation. In this paper, 3D DDA is coupled with tetrahe- dron finite elements to tackle these two problems. Tetrahe- dron is the simplest in the 3D domain and makes it easy to implement automatic discretization, even for complex topol- ogy shape. Furthermore, element faces will remain planar and element edges will remain straight after deformation for tetrahedron finite elements and polyhedral contact detection schemes can be used directly. The matrices of equilibrium equations for this coupled method are given in detail and an effective contact searching algorithm is suggested. Valida- tion is conducted by comparing the results of the proposed coupled method with that of physical model tests using one of the most common failure modes, i.e., wedge failure. Most of the failure modes predicted by the coupled method agree with the physical model results except for 4 cases out of the total 65 cases. Finally, a complex rockslide example demon- strates the robustness and versatility of the coupled method.

THREE-DIMENSIONAL ANALYSIS OF FUNCTIONALLY GRADED PLATE BASED ON THE HAAR WAVELET METHOD

A three-dimensional analysis of a simply-supported functionally graded rectangular plate with an arbitrary distribution of material properties is made using a simple and effective method based on the Haar wavelet. With good features in treating singularities, Haar series solution converges rapidly for arbitrary distributions, especially for the case where the material properties change rapidly in some regions. Through numerical examples the influences of the ratio of material constants on the top and bottom surfaces and different material gradient distributions on the structural response of the plate to mechanical stimuli are studied.

Reconstruction of heat flux profile on the HL-2A divertor plate with a three-dimensional analysis model

A three-dimensional analysis model based on the finite element method （FEM） is developed, which can derive the evolution and distribution characteristics of heat flux deposited on the divertor plate from the surface temperature measured by infrared thermography diagnostics. The numerical simulations of surface heating due to localized power bursts and the power deposition calculations demonstrate that this analysis can provide accurate results and useful information about localized hot spots compared with the normal one- and two-dimensional calculations. In this paper, the details of this three- dimensional analysis are presented, and some results in ohmic heating and electron cyclotron resonant heating （ECRH） discharge on HL-2A are given.

Limit variation analysis of shallow rectangular tunnels collapsing with double-layer rock mass based on a three-dimensional failure mechanism

In the framework of upper bound theorem of limit analysis, the progressive collapse of shallow rectangular tunnels with double-layer rock mass has been theoretically analyzed based on the three-dimensional (3D) velocity discontinuity surfaces. According to the virtual work principle, the difference theorem and the variation method, the collapse surface of double-layer rock mass is determined based on the Hoek-Brown failure criterion. The formula can be degenerated to a single-layer rock collapsing problem when the rock mass is homogeneous. To estimate the validity of the result, the numerical simulation software PLAXIS 3D is used to simulate the collapse of shallow tunnels with double-layer rock mass, and the comparative analysis shows that numerical results are in good agreement with upper-bound solutions. According to the results of parametric analysis, the potential range of collapse of a double-layer rock mass above a shallow cavity decreases with a decrease in A1/A2,σci1/σci2 and σtm1/σtm2 and an increase in B1/B2,γ1/γ2. The range will decrease with a decrease in support pressure q and increase with a decrease in surface overload σs. Therefore, reinforced supporting is beneficial to improve the stability of the cavity during actual construction.

Three-dimensional admittance analysis of lithospheric elastic thickness over the Louisville Ridge

Using bathymetry and altimetric gravity anomalies, a 1°×9 1° lithospheric effective elastic thickness（Te） model over the Louisville Ridge and its adjacent regions is calculated using the moving window admittance technique. For comparison, three bathymetry models are used： general bathymetric charts of the oceans, SIO V15.1,and BAT_VGG. The results show that BAT_VGG is more suitable for calculating T e than the other two models. T e along the Louisville Ridge was re-evaluated. The southeast of the ridge has a medium Te of 10–20 km, while Te increases dramatically seaward of the Tonga-Kermadec trench as a result of the collision of the Pacific and IndoAustralian plates.

Three-dimensional nonlinear analysis of creep in concrete filled steel tube columns

This paper proposes a based on 3D-VLE （three-dimensional nonlinear viscoelastic theory） three-parameters viscoelastic model for studying the time-dependent behaviour of concrete filled steel tube （CFT） columns. The method of 3D-VLE was developed to analyze the effects of concrete creep behavior on CFT structures. After the evaluation of the parameters in the proposed creep model, experimental measurements of two prestressed reinforced concrete beams were used to investigate the creep phenomenon of three CFT columns under long-term axial and eccentric load was investigated. The experimentally obtained time-dependent creep behaviour accorded well with the cu~＇es obtained from the proposed method. Many factors （such as ratio of long-term load to strength, slenderness ratio, steel ratio, and eccentricity ratio） were considered to obtain the regularity of influence of concrete creep on CFT structures. The analytical results can be consulted in the engineering practice and design.

AN APPLICATION OF TOPOLOGICAL ANALYSIS TO STUDYING THE THREE-DIMENSIONAL FLOW IN CASCADES;PART I—TOPOLOGICAL RULES FOR SKIN-FRICTION LINES AND SECTION STREAMLINES

Based on the working of Lighthill and Hunt et al., in the present paper the author has established the topological rules adapting to analysing the skin-friction lines and the section streamlines in cascades. These rules are (1) for a rotor cascade without shroud band, the total number of nodal points equals that the saddle points on the skin-friction line vector fields in eachpitch range; (2) for an annular or straight cascade with no-clearances at blade ends, the total number of saddle points is two more than that of nodal points on the skin-friction line fields in a pitch; (3) the total number of saddles in the secondary flow fields on cross-sections in cascade is one less than that of nodes; (4) in the section streamline vector fields on a meridian surface penetrating a flow passage, and on leading and trailing edge sections, the total number of nodes is equal to that of saddles; (5) on the streamline vector fields of a blade-to-blade surface, the total number of nodes is one less than that of saddles.

Undrained Stability Analysis of Three-Dimensional Rectangular Trapdoor in Clay

A new collapse model of the trapdoors,three-dimensional rectangular trapdoor(3DRT),is presented for ground surface collapse.Undrained stability of 3DRT is examined with the upper bound method of plasticity limit analysis theory.The soil where the trapdoors are located is assumed to be a perfectly plastic model with a Tresca yield criterion.Block analysis technique is employed to investigate the collapse of 3DRT.The model is divided into five different block types and added up to ten rigid blocks.According to the law of conservation of energy,the critical stability ratios of 3DRT are obtained through a search proceeding.The results of upper bound solution for 3DRT are given,and three trapdoor models with depth various are discussed during the application in the stability analysis of square trapdoors.The critical stability ratios can be used in the design of underground excavation and support force.

Three-dimensional mapping and comparative analysis of the distal human corpus cavernosum and the inflatable penile prosthesis

The intricate anatomy of the corpus cavernosum in both the flaccid and tumescent state has not been fully elucidated. We report our experience using a three-dimensional （3D） scanner to reconstruct cadaveric casts and compare them with 3D images of two prototypes of penile prosthesis. Two different models of the Titan Coloplast inflatable penile prosthesis were analyzed using a 3D scanner. The first was the standard model and the second was a newer model with a rounder silicone tip. Two cadaveric phalluses were harvested using Smooth-Cast 300Q polyurethane molding. The molds were excised and scanned along side the penile prosthesis. 3D scans were completed and analyzed using Leios Mesh software, and GOM Inspect software. The 3D scans demonstrated the mean human corporal radii 2 mm from the distal tip to be 36.51 mm （36.01-37.0 mm）, which is an obtuse angle. The standard Titan penile prosthesis spherical radius at the same level was 202.52 mm, while the new silicone tip prosthesis had a radius of 139.33 mm. 3D mapping further demonstrated the trajectory of the cavernosa appeared curvilinear and the distal ends appeared blunt. The use of cadaveric cavernosal molds in combination with the 3D scanner allowed us to accurately image the corpus cavernosum for the first time. Our findings suggest that anatomically accurate corporal tips appear to be relatively blunt and that the new Titan silicone tip penile prosthesis more closely resembles the human corporal tip.

AN APPLICATION OF TOPOLOGICAL METHOD TO ANALYSING THE THREE-DIMENSIONAL FLOW IN CASCADES(Ⅱ)-TOPOLOGICAL ANALYSIS ON THE VECTOR FIELD PATTERNS OF SKINFRICTIONS AND SECTION STREAMLINES

With an application of topological analysis,in this paper the skin-friction line patterns on compressor and turbine cascade surfaces are depicted and the streamline patterns of the secondary flow fields in the cross-section of a curved pipe and a turbine cascade are drawn under given conditions.In addition the structures of vortices within three-dimensional viscous flow fields in cascades are analysed.

MODELING OF LIGHT SPECULAR REFLECTION FROM PLAIN-KNITTED FABRICS: A THREE-DIMENSIONAL ANALYSIS

The paper applies a mathematical model[1] for specular reflection to plain-knitted fabrics by using a three-dimensional analysis. Computer simulation of goniophotometric curves is generated based oa the model. Correction factors are introduced by taking into consideration of geometry of the instrument used. Comparison between the simulated and the measured curves of a straight monofilament yarn with various orientation angles is carried out and reasonable agreement has been obtained.

Demonstration of the refined three-dimensional structure of mesoscale eddies and computational error estimates via Lagrangian analysis

In previous studies,Lagrangian analyses were used to assess large-scale ocean circulation,and the Lagrangian coherent structure could also reveal the evolution of the two-dimensional structure of the mesoscale eddies.However,few studies have demonstrated the three-dimensional structure of the mesoscale eddies via Lagrangian analysis.Compared with previous studies,which investigated the eddy structure via a Eulerian view,we used a Lagrangian view to provide a different perspective to study the eddy structure.An idealized cyclonic mesoscale eddy is built up over a seamount,and it presents downwelling inside the eddy and upwelling alongside the eddy formed within a closed circulation system.This structure is difficult to display via a Eulerian analysis.However,the trajectories of particles can well demonstrate the full cycle:the fluid sank and rotated inside the eddies,converged to the upwelling zone of the bottom layer and returned to the surface through upwelling.We also applied a Lagrangian analysis to a realistic simulation.As a significant phenomenon in the South China Sea,the dipole structure of the anticyclonic eddy(AE)/cyclonic eddy(CE)pair off of central Vietnam has been well studied but mainly at the sea surface.With a Lagrangian analysis,we illustrate the three-dimensional structure of the eddy pair:the fluid sank(rose)and rotated inside the AE(CE).More importantly,the trajectories of the particles suggested that there was no fluid exchange between the two eddies since the strong boundary jet separates them from each other.All the conclusions above have been verified and are supported by the computational error estimate.With a selected time step and integral period,the computational errors always present small values,although they increase with strong divergent and vertical diffusive flow.