Developing Operational Model for Heat Pumps as Space Heating and Domestic Hot Water Provider

In the United Kingdom, means of meeting domestic heating is being electrified to decarbonise in effort to reduce the greenhouse gases emissions from the burning of natural gas. Therefore, the uptake of heat pumps is on the increase. The operation and working principle of heat pumps must be well understood in the investigations of their impacts on the grid and the grid assets, especially distribution transformers which could be overloaded due to higher peak load demand. This work develops an operational model of heat pumps as combined space heating and domestic hot water provider implemented in MATLAB. The developed operational model of heat pumps is adaptable and repeatable for different input parameters. The developed model is used to generate daily average demand profiles of heat pumps for a typical winter weekday and a typical summer weekday. The generated demand profiles of heat pumps by the developed model compared well with the demand profiles of heat pumps generated from actual field projects which are usually expensive and time-tasking.

A Lightweight Electronic Water Pump Shell Defect Detection Method Based on Improved YOLOv5s

For surface defects in electronic water pump shells,the manual detection efficiency is low,prone to misdetection and leak detection,and encounters problems,such as uncertainty.To improve the speed and accuracy of surface defect detection,a lightweight detection method based on an improved YOLOv5s method is proposed to replace the traditional manual detection methods.In this method,the MobileNetV3 module replaces the backbone network of YOLOv5s,depth-separable convolution is introduced,the parameters and calculations are reduced,and CIoU_Loss is used as the loss function of the boundary box regression to improve its detection accuracy.A dataset of electronic pump shell defects is established,and the performance of the improved method is evaluated by comparing it with that of the original method.The results show that the parameters and FLOPs are reduced by 49.83%and 61.59%,respectively,compared with the original YOLOv5s model,and the detection accuracy is improved by 1.74%,which is an indication of the superiority of the improved method.To further verify the universality of the improved method,it is compared with the results using the original method on the PASCALVOC2007 dataset,which verifies that it yields better performance.In summary,the improved lightweight method can be used for the real-time detection of electronic water pump shell defects.

Development and Experimental Study of Air Source Heat Pump Water Heater

The principle and development prospect of air source heat pump water heat were introduced,as well as the designation of condenser (storage water tank),experimental study on installations was also carried out.The results showed that air source heat pump water heater was superior to conventional system.Under the operation of cooling and heating,heat pump comprehensive utilization equipment could improve heating performance,reduce energy consumption,and recycle condensing heat to provide hot water.

Experimental study on characteristics of transcritical heat pump water heater using refrigerant HFC125

To evaluate the performance of heat pumps using refrigerant HFC125,an experimental rig of a DC-inverter heat pump water heater is designed and set up,and the research on the transcritical heat pump water heater is carried out experimentally.It is found that there is a top value of the coefficient of performance（COP）when the system runs at 95 Hz of frequency.The relationships between the COP and compressor frequency,condensation pressure,evaporation pressure,condensation water temperature rise,and discharge temperature are discussed and analyzed at 95 Hz.And the COP of the HFC125 transcritical cycle is also compared with that of a R410 subcritical heat pump under the same conditions.The results indicate that there exists an optimum frequency for a better COP,and the system COP shows an increasing tendency with the decrease in condensation pressure and compressor ratio while the evaporation pressure remains invariant,and the COP decreases rapidly when cooling water temperature rises over 47.5 ℃.Compared with the R410A sub-critical cycle,the COP of HFC125 transcritical cycle significantly increases by 12% on average.

Influence of Valve's Characteristic on Total Performance of Three Cylinders Internal Combustion Water Pump

Intenal combustion pump （ICP） is a new type power device turning the thermal energy from fuel combustion into fluid pressure energy. Three cylinders prototype has just been developed. The study on the influence of valve＇s characteristic on ICP＇s total performance will found the base for its optimum design. Based on the theoretical and testing fruits of single cylinder prototype, the performance of the valves and complete appliance of the latest is simulated. When the natural frequency of valves is approximately to the round number times of the working frequency, volumetric efficiency is seriously low. The nominal rotational speed of the prototype is nearly to the speed where the volumetric efficiency is lowest, which is harmful to the normal work of ICP, so further structure optimization of valves should be carried out. The change of volumetric efficiency has great influence on the fuel consumption rate, output flow, effective thermal efficiency, effective power, and so on, but little on output pressure.

Pressure fluctuation and its influencing factors in circulating water pump

In order to investigate the effect of sampling frequency and time on pressure fluctuations, the three-dimensional unsteady numerical simulations were conducted in a circulating water pump. Through comparison of turbulence models with hydraulic performance experiment, SST k-co model was confirmed to study the rational determination of sampling frequency and time better. The Fast Fourier Transform （FFT） technology was then adopted to process those fluctuating pressure signals obtained. On these bases, the characteristics of pressure fluctuations acting on the tongue were discussed. It is found that aliasing errors decrease at higher sampling frequency of 17 640 Hz, but not at a lower sampling frequency of 1 764 Hz. Correspondingly, an output frequency range ten-times wider is obtained at 17 640 Hz. Compared with 8R, when the sampling time is shorter, the amplitudes may be overvalued, and the frequencies and amplitudes of low-frequency fluctuations can not be well predicted. The frequencies at the tongue are in good agreement with the values calculated by formula and the frequency compositions less than the blade passing frequency are accurately predicted.

DYNAMICS MODEL AND SIMULATION OF FLAT VALVE SYSTEM OF INTERNAL COMBUSTION WATER PUMP

The dynamics differential equations are constructed, and the initial conditions are also given. Simulation shows the following conclusions： The water pressure in cylinder has great instantaneous pulsation and phase step when outlet valve or inlet valve opens, but is more gently in other time; The volume efficiency is influenced by the output pressure slightly, and decreases as the working rotational speed increases; When the inherent frequency of the valves is integer multiple of the working frequency, the volume efficiency of system will decrease evidently.

Studies on the changes of West Lake＇s zoobenthic communites after Qiantang River water was pumped into it

During Jan.1995 to Dec.1996, monthly investigations on the zoobenthic communities of West Lake, samples were collected from six sampling stations. A total of 26 species of macrozoobenthos were identified. The seasonal changes in density and biomass of zoobenthos in this lake were analyzed. The annual mean densities were 980～2751 ind/m\+2 and mean biomass was 19.69-122.80 g/m\+2. The densities in winter and early spring were higher than those in summer and autumn. Comparative study of theprevious data (1982 to 1983) collected by the authors, showed that the succession of zoobenthic communities, dominated by \%Procludius choreus\% in density and \%Bellamya purificata\% in biomass, had been occurred in Xiaonan sub\|lake after Qiantang River water was drawn into it; and that the species and biomass of zoobenthos were then increased and the density was decreased. In other sub\|lakes, the dominant species were \%Limnodrilus hoffmeisteri\% and \%Tokunagayusurika akamusi \%in density and \%Branchiura sowerbyi\% and \%Tokunagayusurika akamusi \%in biomass. The water quality was bad in these sub\|lakes because these dominant species are indicators of eutrophication. According to the Margalef index and Goodnight index, West Lake is still an eutrophic lake. Only the water quality of Xiaonan sub\|lake was improved after water drawn from the Qiantang River was introduced into it.

Feasibility Analysis of Back-Pressure Steam Feeding Water Pump for Direct Air-Cooled Unit

As the performance of an air-cooled condenser is apt to be affected by the fluctuating ambient condition, some difficulties are brought to the use of a steam feeding water pump in an air-cooled unit. This paper introduces a new design of for steam feeding the water pump of an air-cooled unit using the back-pressure steam turbine as the prime motor. Using variable condition analysis on a 600 MW direct air-cooled unit, and with consideration of the effect on the ambient conditions, the feasibility, economy, and adaptability of the design are verified.

Design on Vibration Monitoring and Fault Diagnosis System of Large Water Pump Motor

Large water pump motor,whose operation decides the reliability of the whole production line,plays a very important role.Therefore,its online condition monitoring can help companies better know its operation,process fault analysis and protection.The essay mainly studies and designs large water pump motor′s real time vibration monitoring and fault diagnosis system.The essay completes the systems project design,the establishment of the system and performance test.Eddy-currentsensor,XM-120 vibration module,XM-320 axial translation module,XM-362 temperature module,XM-360 process amount module and XM-500 gateway module are used to measure the axial vibration and displacement of main motors.Laboratory tests prove that the system can meet the requirements of motor vibration monitoring.

Optimal Operation for Baoying Pumping Station in East Route Project of South-to-North Water Transfer

Baoying pumping station is a part of source pumping stations in East Route Project of South-to-North Water Transfer in China. Aiming at the characteristics of head varying, and making use of the function of pump adjustable blade, mathematical models of pumping station optimal operation are established and solved with genetic algorithm. For different total pumping discharge and total pumping volume of water per day, in order to minimize pumping station operation cost, the number and operation duties of running pump units are respectively determined at different periods of time in a day. The results indicate that the saving of electrical cost is significantly effected by the schemes of adjusting blade angles and time-varying electrical price when pumping certain water volume of water per day, and compared with conventional operation schemes （namely, the schemes of pumping station operation at design blade angles based on certain pumping discharge）, the electrical cost is saved by 4.73%-31.27%. Also, compared with the electrical cost of conventional operation schemes, the electrical cost is saved by 2.03%-5.79% by the schemes of adjusting blade angles when pumping certain discharge.

Experimental Study of Thermoelectric Heat Pump Water Heater with Exhaust Heat Recovery from Kitchens

A new kind of thermoelectric heat pump water heater for kitchens exhaust heat recovery was presented,and its performances were investigated under different operating voltages.The experiment results show that the coefficient of performance decreases and the temperature difference between the hot and cold sides becomes larger with the increase of the operating voltage,but the heating time becomes short.The higher the temperature of water,the greater the temperature difference between the hot and cold sides,leading to a smaller coefficient of performance.Under an exhaust temperature of 36 ℃,the coefficient of performance decreases from 1.66 to 1.22 when the temperature of water increases from 28 ℃ to 46 ℃ with operating voltage 16 V.Performance tests illustrate that,compared with the conventional electrical water heaters,the new kind of thermoelectric heat pump water heater is more coefficient.

Optimised Design and Analysis of Solar Water Pumping Systems for Pakistani Conditions

This paper is about the optimized design and analysis of two solar water pumping systems in which one of the systems is designed with a battery bank and other with a cylindrical water tank for a selected site in Pakistan. The design, sizing, cost analysis and steady state analysis of the proposed systems were done in HOMER and dynamic analysis of the designed system with battery bank was performed in MATLAB/Simulink. The simulations performed in HOMER involved proper mapping of the loads which helped to evaluate the PV panel requirement, inverter rating, batteries (in case of battery based solution), modeling of water tank as a deferrable load (in case of solution based of water tank) and detailed cost analysis for a life time of 25 years. To verify the design of the solar water pumping system with battery bank, a simulation in MATLAB/Simulink for study of dynamic behavior of the overall system was performed which involved mathematical modeling of a PV panel, buckboost converter, inverter, battery bank and motor/pump, a perturb and observe maximum power point tracking algorithm based control system. Analysis was conducted based on the economic results that indicate designed solar water pumping system with water tank would be a cheaper solution as compared to solar water pumping system with a battery bank. This work can be taken as a case study for the understanding and optimized designs of solar water pumping system with battery bank and with cylindrical tank in Pakistani conditions.

Comprehensive Study,Design and Economic Feasibility Analysis of Solar PV Powered Water Pumping System

The energy efficient product can be operated with longer duration.They offer wonderful solutions compared to other conventional water pumping system as it needs less maintenance,simple in installation,zero fuel cost,longer operating life,highly reliable and free from production of greenhouse gases.In this paper we analyzed the different topologies of DC–DC converter in terms of their operating region of MPPT,quality of input and output currents.We discussed the MPPT algorithms to address partial shading effects in SPV array,present state of the technology,factors affecting the performance of the system,efficiency improvements and identified the research gaps.Also,the economic feasibility analysis has been done for the real time scenario using the Homer Pro software.The estimation of total dynamic head and horse power calculation has been done to decide the total load capacity.The economic analysis results such as cumulative cash flow over project lifetime of 25 years are presented.It is observed that the capital investment requirement is$7,425 for installing Fronius PV system that has a nominal capacity of 2.47 kW and annualized savings will be$134.93.In the long-term perspective,the return on investment is−2.18%as per the present tariff plan.

Assessment of the Rural Water Supply Potential by Mechanical Wind Pumping Around the Floodplains of Lake Chad

In the present work,an assessment of the rural water supply potential by mechanical wind pumping around the floodplains of Lake Chad has been considered.Inside the floodplains around Lake Chad,available surface water is largely contaminated and represents health hazards to populations.Access to underground and clean water has increasingly become rare.Moreover,clean water scarcity has led to conflict and territorial pressures,which are contributing factors to poverty in the considered area.Four localities,Baga,Baga-Sola,Makari and Nguigmi,respectively,in Nigeria,Chad,Cameroon and Niger have been selected inside the floodplains around Lake Chad,to evaluate the potential of wind power and prospects of windmills development to provide safe drinking-water supply,livestock watering and small-scale irrigation.Long-term satellite-derived data,obtained through the Prediction of Worldwide renewable Energy Resources have been considered suitable and viable alternative to missing site-specific data from ground stations.Windmill of Multi-blade driven piston pump is the preferred water pumping option for this study because of its higher overall system efficiency.The results of this study indicate that mean wind speeds,at 10 m height above ground level,are 4.64 m/s for Baga,4.76 m/s for Baga-Sola,4.32 m/s for Makari and 4.44 m/s for Nguigmi.In addition,wind speeds for Baga,for instance,are in the range of 2.5–10 m(working range of a wind pump),at 10,15,20 and 25 m height agl,for 79.64,82.80,84.79,and 86.19 per cent of the time.Corresponding values for Baga-Sola,Makari and Nguigmi are in the range of 80.50–87.76 per cent,76.86–85,58 per cent,77.92–86.21 per cent,respectively.For a Windmill with a 2 m-blade,a 25 m-height tower and considering a total dynamic head of 30 m,average monthly discharges for the dry season are 1,330,1,374,1,200 and 1,199 m3,respectively for Baga,Baga-Sola,Makari and Nguigmi.Furthermore,corresponding costs of water are 9.53,9.23,10.56 and 10.57 XAF/m3,for Baga,Baga-Sola,Makari and Nguigmi,in that order.

Automatic Control of Water Pumping Stations

Automatic Control of pumps is an interesting proposal to operate water pumping stations among many kinds of water pumping stations according to their functions.In this paper,our pumping station is being used for water supply system. This paper is to introduce the idea of pump controller and the important factors that must be considering when we want to design automatic control system of water pumping stations. Then the automatic control circuit with the function of all components will be introduced.

Study on corrosion behavior of heat exchanger in water source heat pump

Water source heat pump is a new kind of energy saving process.One of the most common problems for water source heat pump system is the corrosion of the copper in heat exchanger.The quality of water is the key factor.The river water collected in six different places of the Yangtze River and Jialing River in Chongqing were analyzed.Various parameters(pH,coexisted ions,and hardness value)were investigated.It showed that the Yangtze River and Jialing River water was suitable for developing water source heat pump technology.Further more,aimed at the temperature and pH of the raw water's variation range in a year,the corrosion behavior of copper material was studied by controlling the water environmental condition.Corrosion rate of copper is accelerated at high temperature and lower pH value.

Design and Performance of Photovoltaic Water Pumping Systems: Comprehensive Review towards a Renewable Strategy for Mozambique

The use of solar photovoltaic (PV) technology for water pumping systems (WPS) has been one of the most popular forms of solar energy application in recent decades in remote and desert areas, as well as in some urban areas. In this article, an advanced literature review on the design and performance of solar technology for water pumping is presented, exploring also the best perspective of transition for the developing countries energy needs. Additionally, this paper intends to analyze the Mozambique’s perspective on renewable energy technologies setting the Mozambican scenario regarding photovoltaic water pumping systems (PVWPS) technology with the aim to identifying the main knowledge of PVWPS design and research gap. The results show that the most commonly used configuration of PVWPS technology is direct coupling systems without battery storage. These systems are simple and reliable, mainly used in small-scale pumping for small irrigations and domestic use. The mainly variables that influence the performance of PVWPS are: total dynamic head, quantity of fluid extracted, variation of solar radiation level, PV and motor pump technology. Yet, the efficiency of the PV and overall system does not exceed 10% and 5%, respectively. Looking at the designing, mathematical models, software-assisted is being predominant. Yet, as research gap, it is possible to understand from different authors that the dynamic nature of the end-use of PVWPS is not explored on methodology design of PVWPS, and the techno-economic optimum system configuration is not always the one that gives the highest annual system efficiency. For the Mozambican’s context, PVWPS for irrigation has been expanding slowly but has gained expression since 2013. In turn, static models based on software of pump manufacturers for PVWPS design are the most widely used in Mozam-bique. In Mozambique, PVWPS match the perspective of different researchers regarding the availability of solar resource, boreholes and amount of water required for irrigation. The adoption of PVWPS is a means of increasing the sustainability of the rural communities.

Influence of long and short guide vanes on hydraulic performance of water-jet pump

Different guide vane structures will affect the flow inside the pump,and then affect the transformation of the pressure energy and kinetic energy,and change the velocity distribution of the pump outlet.In order to study the influence of long and short guide vanes on the water-jet pump,on the basis of conventional design,eight schemes of guide vane with different vertical heights were designed in the method of computational fluid dynamics for numerical calculation,the performance curve of water-jet pumps with different long and short guide vanes was obtained,and finally the influence of different guide vanes on hydraulic performance and internal flow was analyzed.The results show that all of schemes reducing the height of blade can improve the head and efficiency.In the schemes reducing the height on the shroud,the guide vanes that the height of the blade is equal to the height difference between hub and shroud in impeller have the highest head and efficiency.In all schemes decreasing the blade height,with the increase of the height difference,the velocity increases gradually and the distribution of turbulence kinetic energy becomes more reasonable in the guide vane outlet.The schemes reducing the height on the hub have more reasonable distribution of velocity and turbulence kinetic energy according to schemes reducing the height on the shroud.The guide vanes of long and short blades can be used to stagger the position of the diffusion flow generated by adjacent blades,which can reduce the effect of the velocity circulation and make the flow of the outlet position more stable.

Dynamic Modelling of Submersible Pump Based Solar Water-Pumping System with Three-Phase Induction Motor Using MATLAB

The main purpose of this paper is to design and model a water-pumping system using a submersible multi-stage centrifugal pump driven by a three-phase induction motor. The system is intended for pumping water to the surface from a deep well using three power supply systems: a general network, a photo-voltaic (PV) system, and a PV system with a battery bank. These systems are used to compare two three-phase induction motors—namely, a motor with a drive and another one without a drive. The systems dynamic models are simulated in MATLAB/Simulink and the results compared with the manufacturer’s data for validation purposes. The simulation results generally show system dynamics and expected performance over a range of operation.