Effects of laser heat treatment on salt spray corrosion of 1Cr5Mo heat resistant steel welding joints

The surface of 1Cr5 Mo heat-resistant steel welding joint was processed with CO2 laser, and the corrosion behaviors before and after laser heat treatment(LHT) were investigated in the salt spray corrosion environments. The microstructures, phases, residual stresses and retained austenite content of 1Cr5 Mo steel welding joint before and after LHT were analyzed with optical microscope and X-ray diffraction, respectively. The cracking morphologies and chemical compositions of corrosion products after salt spray corrosion were analyzed with field emission scanning electron microscopy(FESEM) and energy disperse spectroscopy(EDS), respectively, the polarization curves were measured on a PS-268 A type electrochemical workstation, and the mechanism of corrosion resistance by LHT was investigated as well. The results show that the passive film of original sample is destroyed owing to the corrosive media penetrating into the subsurface, resulting in the redox reaction. The content of residual austenite in the surface and the self-corrosion potential are increased by LHT, which is contributed to improving the capability of salt spray corrosion resistance.

The Cracking Induced by Oxidation-Hydriding in Welding Joints of Zircaloy-4 Plates

The welding joints of Zircaloy 4 plates obtained by diffusion welding at 800°C under pressure in vacuum were cracked during autoclave tests at 400°C superheated steam after exposure longer than 150 days. The section of specimens was examined by optical microscopy and the composition at the tips of cracking was analyzed by electron microprobe. The result shows that the combination of oxidation and hydriding induced cracking is responsible for this failure of the welding joints.

Microstructures and properties of tungsten inert gas welding joint of super-eutectic ZA alloy

The microstructure of butt welding joint of supper eutectic ZA alloy in TIG welding was analyzed through optical microscope and transmission electronic microscope. The results show that the weld seam microstructure is fine and mainly composed of columnar crystals and minor equiaxed crystals, the microstructure in the zone near the weld seam is coarse columnar crystals, and the grain in heat affected zone does not grow markedly. The joint microstructure at room temperature is consisted of β phase (rich Al), η Zn, ε phase (CuZn compound), Al 4Cu 9 and other compounds. The hardness of the weld bond area and the tensile strength of the joint are a little higher than that of base materials. The specific elongation of the weld and bond area is a little lower than those of base materials. [

Fatigue Behavior of a Dissimilar Aluminum Alloy Welding Joint With and Without Natural Defect

In order to investigate the influence of natural defect on the fatigue behavior of 5A06/7A05 dissimilar aluminum alloys welding joint,fatigue tests of two types of specimens with and without defects were carried out systematically under stress amplitude control conditions (stress ratio R=0.1) at normal temperature in laboratory air condition.Furthermore,a new parameter,i e,fatigue defect effect factor (FDEF) was introduced to assess the effect of defect on fatigue strength.The fatigue failure analysis was conducted as well to compare the fatigue and fracture behavior of the two types of specimens.The results show that:(1) natural defects have a strong effect on the fatigue lives of welding joint,and the differences between the specimens with and without defects can reach 80 times under a same theoretical net sectional stress;(2) the FDEF parameter introduced is effective to deal with the defect effect,and the FDEF decreases along with the increase of fatigue life.The mean relative error between the experimental data and predicted fatigue strength based on the FDEF is 10.2%;(3) the macro fracture of both types of specimens have three typical zones,i e,fatigue source zone,crack propagation zone and final fracture zone,while there are more than one fatigue sources for specimens with natural defects.The overall pattern of crack propagation zone and fracture zone are quite similar,but the morphologies are different in details.

NEW VIEW OF CHARACTERISTIC ZONE CLASSIFICATION OF FUSION WELDING JOINT

A new view of characterstic zone classification of fusion welding joint has been put for-ward on the base of a number of metallograplic observations and researches. TLe characteristiczones of the joint include (1) homogenous mixture region (2)heterogerous mixture zone, (3)partically melting zone and (4) heat-affected zone. (1) and (2) consist of the weld metal. (2) and (3)compose the bond, the boundary betweer (2) and (3) is the fusion line Four kinds of characteristicappearences in the ' heterogenous mixture zone' are induced. The formation process of thecharcteristic zones is distussed in detail. The differences between authors' classification and W. F.Savage's one are compared, to hoping that the formation essence and composition feature of fusionwelding joint can be reasonably reflected.

Mechanism of corrosion fatigue fracture of friction stir welding joints of 7075 aluminium alloy in 3.5% NaCl solution

The corrosion fatigue fracture mechanism of friction stir welding(FSW) joints of 7075 aluminium alloy in3.5% NaCl solution is investigated. The corrosion fatigue crack source originates from the junction of nugget zone(NZ)and thermo-mechanical affected zone(TMAZ). Multiple crack sources are developed at the same time, and they merge into large cracks along the boundary line of NZ and TMAZ during the propagation stage. Furthermore, a mutual reinforcement coupling always exists between corrosion and cyclic loading during the initiation and propagation of corrosion fatigue crack. It is necessary to consider the effect of welding residual stress for understanding the mechanism of corrosion fatigue fracture of FSW joints.

Comparison study on measurement of rail weld joint between inertial reference method and multi-point chord reference method

Purpose – Straightness measurement of rail weld joint is of essential importance to railway maintenance. Dueto the lack of efficient measurement equipment, there has been limited in-depth research on rail weld joint with a5-m wavelength range, leaving a significant knowledge gap in this field.Design/methodology/approach – In this study, the authors used the well-established inertial referencemethod (IR-method), and the state-of-the-art multi-point chord reference method (MCR-method). Two methodshave been applied in different types of rail straightness measurement trollies, respectively. These instrumentswere tested in a high-speed rail section within a certain region of China. The test results were ultimatelyvalidated through using traditional straightedge and feeler gauge methods as reference data to evaluate the railweld joint straightness within the 5-m wavelength range.Findings – The research reveals that IR-method and MCR-method produce reasonably similar measurementresults for wavelengths below 1 m. However, MCR-method outperforms IR-method in terms of accuracy forwavelengths exceeding 3 m. Furthermore, it was observed that IR-method, while operating at a slower speed,carries the risk of derailing and is incapable of detecting rail weld joints and low joints within the track.Originality/value – The research compare two methods’ measurement effects in a longer wavelength rangeand demonstrate the superiority of MCR-method.

Improving Corrosion Resistance of Friction Stir Welding Joint of 7075 Aluminum Alloy by Micro-arc Oxidation

An attempt has been made to improve the corrosion resistance of friction stir welded joints of 7075 aluminum alloys by micro-arc oxidation（MAO）, and the effects of Na2Si O3 concentration in electrolyte on the corrosion resistance of the coatings were discussed. Morphology and phase constituents of the MAO coatings produced in electrolyte with different Na2SiO3 concentrations were analyzed by scanning electron microscopy, confocal laser scanning microscopy and X-ray diffraction. Electrochemical tests were conducted to evaluate the corrosion resistance of the coatings. The results show that the corrosion resistance of the coated joints is much better than that without the ceramic coating, and the ceramic coating produced in the electrolyte with Na2SiO3 concentration 20 g/L showed better corrosion resistance than the others.

Bending Properties and Fracture Behavior of Ti-23Al-17Nb Alloy Laser Beam Welding Joints

Ti-23Al-17Nb alloy is an important high temperature structural material used in the space and aerospace fields. Welding of this alloy is an indispensable processing method, so the microstructures and mechanical properties of these welded joints must be studied to improve the welds. Longitudinal three-point bending tests were conducted to measure the bending ductility of laser beam welded joints. The crack distribution and fracture surface were investigated to further analyze the fracture behavior. The results indicate that the bending ductility decreases as the heat input by the laser beam welding increases. The crack inducing strain reaches 4.24%, while the fracturing strain exceeds 5% when the heat input is below 316 J/cm. If the columnar crystal grain of the weld metal exhibits a uniform orientation, the bending ductility is worse. The fractography analysis shows that the cracking propagates transgranularly and the fracture surface has a cleavage mode.

Microstructure Characterization of High-heat-input Welding Joint of HSLA Steel Plate for Oil Storage Construction

In this paper, microstructure and mechanical properties of welding metals in 610 MPa high strength low alloy （HSLA） were studied after high-heat-input welding. Both the base material and the weld joint proved excellent strength and toughness by vibratory electrogas arc （VEGA） welding under 90 to 100 kJ/cm heatinput. The heat-affected zone （HAZ） was comprised of fine-grain zone （FGZ） and coarse-grain zone （CGZ）, which characterizes fine granular structure and lathing-bainite substructure, It has found that large quantity of dispersed TiN and M23E6 precipitates restrain structure growing in HAZ and strengthen the weldment together with dislocations in the welded joint.

New Developed Welding Electrode for Improving the Fatigue Strength of Welded Joints

A new welding electrode, low transformation temperature electrode (LTTE), was introduced in this paper. It was described in design principle, mechanics, chemical compositions of their deposited metal and manufacturing methods. It was proved that the best transformation starting temperature from austenite to martensite of the deposited metal of LTTE was at about 191℃ and it was obtained by adding alloying elements such as Cr, Ni, Mn and Mo. The microstructure of the weld metal of the LTTE was low carbon martensite and residual austenite. The compressive residual stress was induced around the weld of the LTTE and the -145 MPa in compression could be obtained in middle of weld metal. The fatigue tests showed that the fatigue strength of the longitudinal welded joints welded with the LTTE at 2×106 cycles was improved by 59% compared with that of the same type of welded joints welded with conventional E5015 and the fatigue life was increased by 47 times at 162 MPa. It is a very valuable method to improve the fatigue performance of welded joints.

Joint performance of CO2 laser-MIG hybrid welding 5083-H116 alloy

Laser-MIG hybrid welding process was dealt with 6 mm thick 5083Hl16 Al-Mg alloy plate in butt-joint configuration. Weld formation principle during hybrid welding was explained. The joint properties and microstructure characteristics of welded joints were analyzed by tensile tests, fractographs observed by optical microscopy and scanning electron microscopy （SEM）. Higher heat input could obtain better mechanical properties, and tensile strength and elongation reached 97.2%, 81% of the base metal, respectively. Fracture position traasited from fusion line to weld center in the higher heat input, and fracture location were only in the center of welded joints for the heat input relatively small.

Weld Joint Efficiency of the Kazakhstani Constructional Steel

In the Republic of Kazakhstan, the regulatory framework in construction based on Eurocodes has been in force since 2015. However, Kazakhstani produced steel has not been studied for compliance with the requirements of Eurocode 1993. This has resulted in limited use of Kazakhstani structural steel in construction. The feasibility of using structural steel in welded joints has been experimentally investigated. To verify the application of such joints in construction, including earthquake engineering, experimental studies of welded joints made of structural steel produced by Arcelor-Mittal in Temirtau have been carried out. In total, 7 types of structural steel of various thicknesses were selected. Five specimens have been used in each series of tests. The Brinell hardness values of the weld joint, yield strength of steel and tensile strength, relative rupture strain were determined. It was found that for all types of structural steel, the quality of weld joints complied with the requirements of Eurocode 1993—a sample rupture appeared along the plates (main body of the metal), not along the weld joints. It has been established that structural steel produced in the Republic of Kazakhstan fully complies with the requirements of Eurocode 1993. The studies on the dependence of Brinell hardness values of weld joint steel on the yield strength, tensile strength and relative rupture strain have been carried out. The correlation dependences between the values of yield strength of steel and tensile strength, relative rupture strain and BH Brinell hardness were studied. The results of work will allow for significantly increasing the use of Kazakhstani structural steel in seismic and conventional areas of the Republic of Kazakhstan.

Comparison of FSW and TIG welded joints in Al-Mg-Mn-Sc-Zr alloy plates

In order to study the welding process,microstructure and properties of Al-Mg-Mn-Sc-Zr alloy,comparative methods of friction stir welding（FSW） and tungsten inert gas（TIG） were applied to the two conditions of this alloy,namely hot rolled plate and cold rolled-annealed plate.The relationships between microstructures and properties of the welded joints were investigated by means of optical microscopy and transmission electron microscopy.Compared with the base metal,the strength of FSW and TIG welded joints decreased,and the FSW welding coefficients were higher than the TIG welding coefficients.The loss of substructure strengthening and a very little loss of precipitation strengthening of Al3（Sc,Zr） cause the decreased strength of FSW welded joint.But for the TIG welded joint,the disappearance of both the strain hardening and most precipitation strengthening effect of Al3（Sc,Zr） particles contributed to its softening.At the same time,the grains in weld nugget zone of FSW welded joints were finer than those in the molten zone of TIG welded joints.

Determination of local constitutive behavior and simulation on tensile test of 2219-T87 aluminum alloy GTAW joints

The local and global mechanical responses of gas tungsten arc welds（GTAW） of a 2219-T87 aluminum alloy were investigated with experiment and numerical simulation.Digital image correlation（DIC） was used to access the local strain fields in transversely loaded welds and to determine the local stress-strain curves of various regions in the joint.The results show that the DIC method is efficient to acquire the local stress-strain curves but the curves of harder regions are incomplete because the stress and strain ranges are limited by the weakest region.With appropriate extrapolation,the complete local stress-strain curves were acquired and proved to be effective to predict the tensile behavior of the welded joint.During the tensile process,the fracture initiates from the weld toes owing to their plastic strain concentrations and then propagates along the fusion line,finally propagates into the partially melted zone（PMZ）.

Fatigue behavior and life prediction of A7N01 aluminium alloy welded joint

Fatigue characteristics of A7N01 aluminium alloy welded joint were investigated and a fatigue crack initiation life-based model was proposed. The difference of fatigue crack initiation life among base metal, weld metal and heat affected zone (HAZ) is slight. Furthermore, the ratio of fatigue crack initiation life (Ni) to fatigue life to failure(Nf) is a material dependent parameter, 26.32%, 40.21% and 60.67% for base metal, HAZ and weld metal, respectively. Total fatigue life predicted using the presented model is in good agreement with the experimental data and that using Basquin’s model. The observation results of fatigue fracture surfaces, using scanning electron microscope (SEM), demonstrate that fatigue crack initiates from smooth surface due to welding process for weld metal, blowhole in HAZ causes fatigue crack initiation, and the crushed second phase particles play an important part in fatigue crack initiation in base metal.

Fatigue behavior of AZ31B magnesium alloy electron beam welded joint based on infrared thermography

Fatigue behavior of AZ31B magnesium alloy electron beam welded joint undergoing cyclic loading was investigated by infrared thermography. Temperature evolution throughout a fatigue process was presented and the mechanism of heat generationwas discussed. Fatigue limit of the welded joint was predicted and the fatigue damage was also assessed based ontheevolution of the temperatureand hotspot zone on the specimen surfaceduring fatigue tests. The presented results show that infrared thermography can not onlyquicklypredict the fatigue behavior of the welded joint, but also qualitatively identify the evolution of fatigue damage in real time. It is found that the predicted fatigue limit agrees well with the conventionalS-Nexperimental results. The evolution of the temperatureand hotspot zone on the specimen surface can be an effectivefatigue damage indicatorfor effectiveevaluationof magnesium alloy electron beam welded joint.

Corrosion behavior of the friction-stir-welded joints of 2A14-T6 aluminum alloy

The corrosion behavior of friction-stir-welded 2A14-T6 aluminum alloy was investigated by immersion testing in immersion exfoliation corrosion（EXCO） solution. Electrochemical measurements（open circuit potential, potentiodynamic polarization curves, and electrochemical impedance spectroscopy）, scanning electron microscopy, and energy dispersive spectroscopy were employed for analyzing the corrosion mechanism. The results show that, compared to the base material, the corrosion resistance of the friction-stir welds is greatly improved, and the weld nugget has the highest corrosion resistance. The pitting susceptibility originates from the edge of Al-Cu-Fe-Mn-Si phase particles as the cathode compared to the matrix due to their high self-corrosion potential. No corrosion activity is observed around the θ phase（Al2Cu） after 2 h of immersion in EXCO solution.

Influence of Creep Strength of Weld on Interfacial Creep Damage of Dissimilar Welded Joint between Martensitic and Bainitic Heat-Resistant Steel

The mechanical properties, creep rupture strength, creep damage and failure characteristics of dissimilar metal welded joint （DMWJ） between martensitic （SA213T91） and bainitic heat-resistant steel （12Cr2MoWVTiB（G102）） have been investigated by means of pulsed argon arc welding, high temperature accelerated simulation, mechanical and creep rupture test, and scanning electronic microscope （SEM）. The results show that there is a marked drop of mechanical properties of undermatching joint, and low ductility cracking along weld/G102 interface is induced due to creep damage. Creep rupture strength of overmatching joint is the least. The mechanical properties of medium matching joint are superior to those of overmatching and undermatching joint, and creep damage and failure tendency along the interface of weld/G102 are lower than those of overmatching and undermatching joint after accelerated simulation for 500 h, 1 000 h, 1 500 h, and the creep rupture strength of medium matching joint is the same as that of undermatching joint. Therefore, it is reasonable that the medium matching material is used for dissimilar welded joint between martensitic and bainitic steel.

Prediction of vulnerable zones based on residual stress and microstructure in CMT welded aluminum alloy joint

Numerical simulation and experimental results were employed for the identification of the most vulnerable zones in three-pass cold-metal-transferring （CMT） welded joint. The residual stress distribution in the joint was predicted by finite element （FE） method, while the structural morphology of distinctive zones was obtained through metallographic experiments. The highest principal stress made the symmetric face of the joint most sensitive to tensile cracks under service conditions. Whereas, the boundaries between the weld seam and the base plates were sensitive to cracks because the equivalent von Mises stress was the highest when the first interpass cooling was finished. The third weld pass and the inter-pass remelted zones exhibited the modest mechanical performances as a result of the coarse grain and coarse grain boundary, respectively. The most vulnerable zones were regarded to be the crossed parts between the zones identified by numerical and experimental methods.