Fine spheroidal and equiaxed nondendritic microstructures required for semisolid casting can be formed through a serpentine pouting channel. Effects of the pouring temperature and the vertical section length of the se...Fine spheroidal and equiaxed nondendritic microstructures required for semisolid casting can be formed through a serpentine pouting channel. Effects of the pouring temperature and the vertical section length of the serpentine pouring channel were studied. The results indicate that both favorable semisolid microstructures of A356 aluminum alloy can be generated by a serpentine pouring channel, and the solid shell inside the channel can be avoided when the pouting temperature is in the range from 660 to 680℃. It is also shown that the vertical section length of the serpentine pouting channel has a significant influence on the microstructure of the feedstock, namely both the microstructure of the feedstock and the microstructure uniformity in the radial direction get worse when the vertical section length is shortened; moreover, the pouring temperature for obtaining the feedstock with suitable microstructure decreases. The relevant mechanisms were discussed.展开更多
The semisolid slurry of Al-Zn-Mg-Cu alloy was prepared through a self-designed water-cooled copper serpentine pouring channel(WSPC) machine. Influences of pouring temperature, the number of turns and the cooling water...The semisolid slurry of Al-Zn-Mg-Cu alloy was prepared through a self-designed water-cooled copper serpentine pouring channel(WSPC) machine. Influences of pouring temperature, the number of turns and the cooling water flow rate on the microstructure of the semisolid Al-Zn-Mg-Cu alloy slurry were investigated. The results show that the semisolid Al-Zn-Mg-Cu alloy slurry with satisfactory quality can be generated by the WSPC when the pouring temperature is in the range between 680 ℃ and 700 ℃. At a given pouring temperature, the average grain size of primary α-Al decreases and the shape factor increases with the increase of the number of turns. When the cooling water flow rate is 450 L·h^(-1), the obtained semisolid slurry is optimal. During the preparation of the semisolid Al-Zn-Mg-Cu alloy slurry with low superheat pouring, the alloy melt has mixed inhibition and convection flow characteristics by "self-stirring". When the alloy melt flows through the serpentine channel, the chilling effect of the inner wall of the channel, the convection and mixed inhibition of the alloy melt greatly promote the heterogeneous nucleation and grain segregation. This effect destroys the dendrite growth mode under traditional solidification conditions, and the primary nuclei gradually evolve into spherical or nearspherical grains.展开更多
The epithermal neutron shape factor (α) was determined in the permanent cadmium lined irradiation channel installed in the large outer irradiation site of the Nigeria Research Reactor-1 (NIRR- 1) by the cadmium cover...The epithermal neutron shape factor (α) was determined in the permanent cadmium lined irradiation channel installed in the large outer irradiation site of the Nigeria Research Reactor-1 (NIRR- 1) by the cadmium covered multimonitor method using the monitors Al-0.1% Au, Zr and Zn thin foils and Mo thin wire and was found to be -0.137 ± 0.018. The high negative value of α indicates a hardened epithermal neutron spectrum in the cadmium lined irradiation channel. The α value obtained was used in the single comparator method of ENAA (ko-ENAA) for the determination of the concentrations of elements in the standard reference material NIST 1515 Apple leaves using Al-0.1% Au thin foil as the single comparator. The concentrations of the elements Sm and Br were determined in the NIST 1515 Apple leaves because of their high Qo values and are in good agreement with the certified values.展开更多
基金supported by the National Basic Research Program of China (No.2006CB605203)the National High-Tech Research and Development Program of China (No.2006AA03Z115)the National Natural Science Foundation of China (No.50774007)
文摘Fine spheroidal and equiaxed nondendritic microstructures required for semisolid casting can be formed through a serpentine pouting channel. Effects of the pouring temperature and the vertical section length of the serpentine pouring channel were studied. The results indicate that both favorable semisolid microstructures of A356 aluminum alloy can be generated by a serpentine pouring channel, and the solid shell inside the channel can be avoided when the pouting temperature is in the range from 660 to 680℃. It is also shown that the vertical section length of the serpentine pouting channel has a significant influence on the microstructure of the feedstock, namely both the microstructure of the feedstock and the microstructure uniformity in the radial direction get worse when the vertical section length is shortened; moreover, the pouring temperature for obtaining the feedstock with suitable microstructure decreases. The relevant mechanisms were discussed.
基金financially supported by the National Natural Science Foundation of China(Grant No.51701078)China Postdoctoral Science Foundation(Grant Nos.2018M632846 and 2018T110756)the Scientific Research Program of Hubei Provincial Education Department(Grant No.B2016053)
文摘The semisolid slurry of Al-Zn-Mg-Cu alloy was prepared through a self-designed water-cooled copper serpentine pouring channel(WSPC) machine. Influences of pouring temperature, the number of turns and the cooling water flow rate on the microstructure of the semisolid Al-Zn-Mg-Cu alloy slurry were investigated. The results show that the semisolid Al-Zn-Mg-Cu alloy slurry with satisfactory quality can be generated by the WSPC when the pouring temperature is in the range between 680 ℃ and 700 ℃. At a given pouring temperature, the average grain size of primary α-Al decreases and the shape factor increases with the increase of the number of turns. When the cooling water flow rate is 450 L·h^(-1), the obtained semisolid slurry is optimal. During the preparation of the semisolid Al-Zn-Mg-Cu alloy slurry with low superheat pouring, the alloy melt has mixed inhibition and convection flow characteristics by "self-stirring". When the alloy melt flows through the serpentine channel, the chilling effect of the inner wall of the channel, the convection and mixed inhibition of the alloy melt greatly promote the heterogeneous nucleation and grain segregation. This effect destroys the dendrite growth mode under traditional solidification conditions, and the primary nuclei gradually evolve into spherical or nearspherical grains.
文摘The epithermal neutron shape factor (α) was determined in the permanent cadmium lined irradiation channel installed in the large outer irradiation site of the Nigeria Research Reactor-1 (NIRR- 1) by the cadmium covered multimonitor method using the monitors Al-0.1% Au, Zr and Zn thin foils and Mo thin wire and was found to be -0.137 ± 0.018. The high negative value of α indicates a hardened epithermal neutron spectrum in the cadmium lined irradiation channel. The α value obtained was used in the single comparator method of ENAA (ko-ENAA) for the determination of the concentrations of elements in the standard reference material NIST 1515 Apple leaves using Al-0.1% Au thin foil as the single comparator. The concentrations of the elements Sm and Br were determined in the NIST 1515 Apple leaves because of their high Qo values and are in good agreement with the certified values.
