Synthesis and characterization of the copolymers (PAG) of α-methyl styrene (AMS) and glycidyl methacrylate (GMA) are presented. The copolymers of PAG were characterized by gel permeation chromatography (GPC),...Synthesis and characterization of the copolymers (PAG) of α-methyl styrene (AMS) and glycidyl methacrylate (GMA) are presented. The copolymers of PAG were characterized by gel permeation chromatography (GPC), Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance (^1H-NMR) and thermogravimetery (TG). Based on the copolymer compositions determined by ^1H-NMR, the reactivity ratios of AMS and GMA were found to be 0.105 ± 0.012 and 0.883 ± 0.046 respectively by Kelen-Tudos method. TG revealed that thermal stability of the copolymers decreased with increasing the AMS content in the copolymers, which indicated that the degradation was mainly caused by the chain scission of AMS-containing structures. Under heating, the copolymers depolymerize at their weak bonds and form chain radicals, which could further initiate other chemical reactions.展开更多
A phosphorus-containing monomer (lO-oxo-10-hydro-9-oxa-10λ^5-phosphaphenanthrene-10-yl)-methyl acrylate (MD was copolymerized with styrene to give a potential flame retardant copolymer of high thermal stability. T...A phosphorus-containing monomer (lO-oxo-10-hydro-9-oxa-10λ^5-phosphaphenanthrene-10-yl)-methyl acrylate (MD was copolymerized with styrene to give a potential flame retardant copolymer of high thermal stability. The structures of monomer and copolymer were characterized by FT-IR and ^1H NMR measurements. The reactivity ratios for free-radical of the monomer (M1) and styrene (Mz) were studied. The calculated results are as follows: r1 = 0.225, r2 = 0.503; Q1 = 0.413, e1 = 0.476; azeotropic point = 0.37. TGA and DTG curves indicated that Ml is a potential flame retarding monomer for styrenic polymers. C 2009 Yu Bin Zheng. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.展开更多
Catalytic epoxidation of alkenes is an important type of organic reaction in chemical industry,and the deep insight into catalyst deactivation will help to develop new epoxidation process.In this work,series of quater...Catalytic epoxidation of alkenes is an important type of organic reaction in chemical industry,and the deep insight into catalyst deactivation will help to develop new epoxidation process.In this work,series of quaternary ammoniums bearing different cationic sizes,i.e.MTOA+(methyltrioctylammonium,[(C_(8)H_(17))_(3)CH_(3)N]+),HTMA+(hexadecyltrimethylammonium,[(C_(16)H_(33))(CH_(3))_(3)N]+) and DMDOA+(dimethyldioctadecylammonium,[(C_(18)H_(37))_(2)(CH_(3))_(2)N]+) were incorporated with polyoxometalate (POM) anions to prepare phase transfer catalysts (PTCs),which were used in the styrene epoxidations.Among them,(MTOA)_(3)PW_(4)O_(24)exhibits the best catalytic performance judged from the highest styrene conversion rate(52%) and styrene oxide selectivity (93%),during which the styrene epoxidation conditions were optimized.Meanwhile,the deactivation mechanism of this kind of PTCs was proposed firstly,i.e.in the case of low H_(2)O_(2) content,the oxidant can only be used in the styrene epoxidation,in which the catalyst can transform into stable Keggin-type POM.But when the content of H_(2)O_(2) is higher,the excess H_(2)O_(2) can reactivate the Keggin-type POM into active (PW_(4)O_(24))_(3)-anions,which can trigger the ring-opening polymerization of styrene oxide.Consequently,the catalyst is deactivated by adhered poly(styrene oxide)irreversibly,which was determined by NMR spectra.In this situation,the active moiety{PO_(4)[WO(O_(2))_(2)]_(4)}_(3)-in phase-transfer catalytic system can break into some unidentified species with low W/P ratio with the presence of epoxides.This work will be beneficial for the design of new PTCs in alkene epoxidation in fine chemical industry.展开更多
[Objectives]To establish a thin-layer chromatography(TLC)method for the determination of rubiadin-1-methyl ether in Yao Medicine Chuanlianzhu(Damnacanthus giganteus).[Methods]A silica gel G thin-layer plate was adopte...[Objectives]To establish a thin-layer chromatography(TLC)method for the determination of rubiadin-1-methyl ether in Yao Medicine Chuanlianzhu(Damnacanthus giganteus).[Methods]A silica gel G thin-layer plate was adopted for TLC.Petroleum ether(60-90℃)-chloroform-methanol-water(7:15:3:1)was used as the developing solvent and inspected under ultraviolet lamp(365 nm).The content was determined by Inertsil ODS-3 C 18 column(4.60 mm×250 mm,5μm),mobile phase:acetonitrile-0.2%phosphoric acid gradient elution,detection wavelength 277 nm,flow rate 1.0 mL/min,column temperature 30℃,injection volume 10μL.[Results]The spots of 10 Chuanlianzhu samples from different origins showed the same color at the same position as the control,and the spots were clear and specific.The injection volume of rubiadin-1-methyl ether showed a good linear relationship in the range of 2.90-145μg(R=0.9996).The average recovery rate of rubiadin-1-methyl ether in the low,medium and high dose groups of Yao Medicine Chuanlianzhu was 98.72%,and RSD=1.78%.[Conclusions]This method can effectively identify Yao Medicine Chuanlianzhu medicinal materials and accurately determine the content of rubiadin-1-methyl ether in the medicinal materials.It provides a scientific basis for the development and utilization of Yao Medicine Chuanlianzhu medicinal resources.展开更多
Bottled water may not be safer, or healthier, than tap water. The present studies have proved that styrene and some other aromatic compounds leach continuously from polystyrene (PS) bottles used locally for packagin...Bottled water may not be safer, or healthier, than tap water. The present studies have proved that styrene and some other aromatic compounds leach continuously from polystyrene (PS) bottles used locally for packaging. Water sapmles in contact with PS were extracted by a preconcentration technique called as "purge and trap" and analysed by gas chromatograph-mass spectrometer (GC/MS). Eleven aromatic compounds were identified in these studies. Maximum concentration of styrene in PS bottles was 29.5 μg/L. Apart from styrene, ethyl benzene, toluene and benzene were also quantified but their concentrations were much less than WHO guide line values. All other compounds were in traces. Quality of plastic and storage time were the major factor in leaching of styrene. Concentration of styrene was increased to 69.53 μg/L after one-year storage. In Styrofoam and PS cups studies, hot water was found to be contaminated with styrene and other aromatic compounds. It was observed that temperature played a major role in the leaching of styrene monomer from Styrofoam cups. Paper cups were found to be safe for hot drinks.展开更多
Using cetyl-trimethyl-ammonium bromide (CTMAB) as the template agent and tetraethylorthosilicate (TEOS) as the silica source, the MCM-41 mesoporous materials were synthesized with La or Ce incorporated in the fram...Using cetyl-trimethyl-ammonium bromide (CTMAB) as the template agent and tetraethylorthosilicate (TEOS) as the silica source, the MCM-41 mesoporous materials were synthesized with La or Ce incorporated in the framework under hydrothermal conditions. The structure and the state of La or Ce were investigated through the analyses of XRD, nitrogen adsorption-desorption, FT-IR, and UV-Vis. XRD and N2 adsorption-desorption results showed that Ln-MCM-41 exhibited the loss of the lattice ordering of the MCM-41 construct, and larger unit cell parameter and pore diameter than pure silica MCM-41. The FT-IR and UV-Vis results indicated the presence of isolated tetra-coordinated La or Ce ions in the framework and other Ln species dispersed highly on the Ln-MCM-41 surface simultaneously. Furthermore, their catalytic behaviors in the oxidation of styrene were studied using H2O2 as the oxidant. The La-MCM-41 catalysts exhibited high reactivity and the reactivity increased with the increase of the La content in the La-MCM-41 samples. On the contrary, Ce-MCM-41 catalysts showed low reactivity in the oxidation of styrene and the conversion of styrene decreased with the increase of the Ce content in the Ce-MCM-41 samples.展开更多
The adsorption behavior and description behavior of benzene , ethylene and ethylbenzene over HZSM-5 and Co/HZSM-5 catalysts were studied by means of TPSR (Temperature programmed surface reaction) technique. TPSR resul...The adsorption behavior and description behavior of benzene , ethylene and ethylbenzene over HZSM-5 and Co/HZSM-5 catalysts were studied by means of TPSR (Temperature programmed surface reaction) technique. TPSR results of ben- zene and ethylene co-adsorption show that the maian products are styrene , ethylben- zene, toluene, propane, and butane. In a separate experiment of ethylbenzene ad- sorption, styrene . toluene and benzene are formed due to cracking and dehydro- genation. The mechanism of styrene formation was proposed , i. e. , the reaction was carried out via. the dehydrogenation of mediate species ethylbenzene according to the results of TPSR-MS , activity testing and thermodynamic analysis.展开更多
Sulfur hexafluoride (SF6) is known as one of the most powerful greenhouse gases in the atmosphere. Reductive photodegradation of SF6 by styrene has been studied with the purpose of developing a novel remediation for...Sulfur hexafluoride (SF6) is known as one of the most powerful greenhouse gases in the atmosphere. Reductive photodegradation of SF6 by styrene has been studied with the purpose of developing a novel remediation for sulfur hexafluoride pollution. Effects of reaction conditions on the destruction and removal efficiency (DRE) of SF6 are examined in this study. Both initial styrene-to-SF6 ratio and initial oxygen concentration exert a significant influence on DRE. SF6 removal efficiency reaches a maximum value at the initial styrene-to-SF6 ratio of 0.2. It is found that DRE increases with oxygen concentration over the range of 0 to 0.09 mol/m^3 and then decreases with increasing oxygen concentration. When water vapor is fed into the gas mixture, DRE is slightly enhanced over the whole studied time scale. The X-ray Photoelectron Spectroscopy (XPS) analysis, together with gas chromatography-mass spectrometry (GC-MS) and Fourier Transform Infrared spectroscopy (FT-IR) analysis, prove that nearly all the initial fluorine residing in the gas phase is in the form of SiF4, whereas, the initial sulfur is deposited in the form of elemental sulfur, after photodegradation. Free from toxic byproducts, photodegradation in the presence of styrene may serve as a promising technique for SF6 abatement.展开更多
Emulsion copolymerization of styrene and ethylene catalyzed by a series of neutral nickel(Ⅱ) complexes was carried out in an aqueous system to give high-molecular-weight copolymers.The copolymers and emulsions were c...Emulsion copolymerization of styrene and ethylene catalyzed by a series of neutral nickel(Ⅱ) complexes was carried out in an aqueous system to give high-molecular-weight copolymers.The copolymers and emulsions were characterized by an array of techniques including NMR,GPC,TEM,WAXD and DSC.The results indicate that the copolymers obtained are mostly block copolymers of polyethylene with random insertion of styrene units,and their M_W is in the range of 10~5-10~6.By enhancing the electron withdrawing of the s...展开更多
Copolymerization of styrene (St) with N-phenylmaleimide (NPMI) was studied with rare earth coordination catalyst Nd(naph)3-AlEt3 in toluene. Characterization of the copolymers showed that the copolymers possess an al...Copolymerization of styrene (St) with N-phenylmaleimide (NPMI) was studied with rare earth coordination catalyst Nd(naph)3-AlEt3 in toluene. Characterization of the copolymers showed that the copolymers possess an alternating structure.展开更多
In order to control the surface pore sizes of polyvinylidene fluoride membranes and their distribution, low temperature plasma-induced grafting modifications of PVDF were studied to prepare hydrophobe membranes. By ar...In order to control the surface pore sizes of polyvinylidene fluoride membranes and their distribution, low temperature plasma-induced grafting modifications of PVDF were studied to prepare hydrophobe membranes. By argon (Ar) treating and subsequent grafting reaction, a hydrophobe monomer, styrene, was introduced into the PVDF membrane. Fourier transform infrared attenuated total reflection (FTIR-ATR) was utilized to characterize the chemical and physical changes in the Ar plasma modified membrane. The surface modifications of PVDF membranes were investigated by using scanning electron microscopy (SEM), atomic force microscopy (AFM) and differential scanning calorimeter (DSC). The water permeability and the solute rejection were measured by PVDF membrane modified in different graft conditions. Results demonstrated that the pores in the modified membranes get smaller and the distribution of pores gets narrowed with the increase in grafting reaction duration. Longer graft time caused the water flux of PVDF membrane to decrease from 578 kg/(m^2· h) to 23 kg/(m^2· h) and the solute rejection to increase from 73% to 92%.展开更多
The catalytic activity of poly(styrene-acrylic acid) (PSAA) supported neodymium chloride (NdCl3) complex for the copolymerization of styrene and 4-Vinylpyridine was studied. The influence of various factors, suc...The catalytic activity of poly(styrene-acrylic acid) (PSAA) supported neodymium chloride (NdCl3) complex for the copolymerization of styrene and 4-Vinylpyridine was studied. The influence of various factors, such as Al/Nd molar ratio, reaction time, macromolecular carder (PSAA), and ratio of styrene to 4-vinypyridine (g/g), on the copolymerization yield of styrene and 4-Vinylpyridine was investigated. The results showed that the copolymerization of polar monomers with olefins occurred efficiently and the catalytic activity of polymer-supported catalyst was higher than that of the similar small molecular catalysts. The activity of PSAA.Nd complex increased with in- creasing Al/Nd molar ratios and decreased with increasing polymerization time. The highest activity of PSAA'Nd was observed at 120 min, and the highest yield was found at the ratio of styrene to 4-vinylpyridine of 4:2. DSC analysis presented that the resulted polymer had only one glass transition temperature, and showed very good thermal stability.展开更多
A new kind of multifunctional macromolecular initiator with Sn-C bonds and polydiene arms was synthesized by living anionic polymerization. At first, polydiene-stannum chloride (PD-SnCl3) was prepared by the reactio...A new kind of multifunctional macromolecular initiator with Sn-C bonds and polydiene arms was synthesized by living anionic polymerization. At first, polydiene-stannum chloride (PD-SnCl3) was prepared by the reaction of n-butyl-Li (n-BuLi), stannic chloride (SnCl4) and diene. Then PD-SnCl3 was used to react with the dilithium initiator to prepare the multifunctional organic macromolecular initiators. The result suggested that the initiators had a remarkable yield by GPC, nearly 90%. By using these multifunctional macromolecular initiators, styrene and butadiene were effectively polymefized via anionic polymerization, which gave birth to novel miktoarm star copolymers. The relative molecular weight and polydispersity index, microstructure contents, copolymerization components, glass transition temperature (Tg) and morphology of the miktoarm star copolymers were investigated by GPC-UV, ~H NMR, DSC and TEM, respectively. 2009 Xing Ying Zhang. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.展开更多
The new V-MCM-41 molecular sieves with good ordered hexagonal mesoporous structure and crystallinity were synthesized through in-situ hydrothermal preparation method. The effects of the crystallization time were discu...The new V-MCM-41 molecular sieves with good ordered hexagonal mesoporous structure and crystallinity were synthesized through in-situ hydrothermal preparation method. The effects of the crystallization time were discussed. The synthesized samples were characterized by X-ray diffraction, N2adsorption/desorption, Fourier transformed infrared and scanning electron microscopy. The different structures, textures, morphologies of V-MCM-41 obtained with different crystallization times were observed and analyzed on the basis of the characterized results. The results showed that the V-MCM-41 molecular sieve obtained at 110?°C for 48?h crystallization times was of good spherical morphology, ordered hexagonal structure, most uniform pore size distribution and high surface area compared with other samples. Meanwhile, the V-MCM-41 molecular sieve with the high skeleton Si condensation and the good crystallinity was obtained. The heteroatom could be incorporated into MCM-41 framework with increasing crystallization times, which was beneficial to improve the catalytic activity and selectivity of pure siliceous MCM-41. The V-MCM-41 showed the good catalytic selectivity in catalytic oxidation of styrene using hydrogen peroxide, and the selectivity of the benzaldehyde and phenylacetic acid reached 30.68% and 49.44%, respectively. ? 2016展开更多
The polymerization behaviors of Styrene (St) in the presence of CuX/L [X=Cl or Br; L= 2,2 bipyridine (bpy), 1,10 phenanthroline (phen) or 4,7 diphenyl 1,10 phenanthroline (DPP) ] and R X (R=trichloromethyl, benz...The polymerization behaviors of Styrene (St) in the presence of CuX/L [X=Cl or Br; L= 2,2 bipyridine (bpy), 1,10 phenanthroline (phen) or 4,7 diphenyl 1,10 phenanthroline (DPP) ] and R X (R=trichloromethyl, benzyl or allyl; X=Cl or Br) have been studied and examined. In a CuCl/bpy/RCl/St system, a bimodal GPC peak at the early stage of polymerization was observed, and a concept of multi active species was proposed to explain this phenomenon. In a CuCl/phen (DPP)/RCl/St system, the \%M\%\-n of polystyrene (PS) increased linearly with St conversion and ln[M] o/[M] also increased linearly with time, indicating the living nature of this system. Furthermore, the stability of the propagating active species in a CuBr/phen/RBr/St system is higher than that in the CuBr/phen/RBr/St system.展开更多
The synthesis of organolanthanide compounds identified as LnCp^*(MS)2PzA, Ln = Sm, Tb, Yb (MS = methanesulfonate, Cp^* = pentamethylcyclopentadienyl, and PzA = pyrazinamide), by the reaction of coordination comp...The synthesis of organolanthanide compounds identified as LnCp^*(MS)2PzA, Ln = Sm, Tb, Yb (MS = methanesulfonate, Cp^* = pentamethylcyclopentadienyl, and PzA = pyrazinamide), by the reaction of coordination compounds Ln(MS)3(PzA)4 with NaCp in THF was reported. The complexes were formulated according to elemental analyses, complexometric titration with EDTA (%Ln), and ^1H NMR. IR spectroscopy revealed that PzA coordinates with lanthanide (Ⅲ) ions and methanesulfonate coordinates via oxygen atoms in a non-equivalent manner. In preliminary catalytic studies, these compounds were active in styrene polymerization that used MAO as a cocatalyst with an activity of 12.3 kg PS molSm^-1h^-1. Differential scanning calorimetry (DSC) of polystyrene showed that the polymer was mainly atactic.展开更多
Thermoregulated phase-separable Ru3(CO)12/PETPP (PETPP=P[p-C6H4O (CH2CH2O)n H]3, n=6) complex catalyst was first applied in the hydrogenation of styrene. Under the conditions: P(H2)=2.0MPa, T=90C, styrene could be com...Thermoregulated phase-separable Ru3(CO)12/PETPP (PETPP=P[p-C6H4O (CH2CH2O)n H]3, n=6) complex catalyst was first applied in the hydrogenation of styrene. Under the conditions: P(H2)=2.0MPa, T=90C, styrene could be completely transferred and the yield of ethylbenzene reached up to 99.5%. After simple decantation, the catalyst could be reused for ten times without decreasing in activity.展开更多
Neutral nickel sigma -acetylide complex [Ni(C=CPh)(2)(PBu3)(2)] is a novel initiator for the polymerization of styrene in CHCl3 over a range of polymerization temperature from 40 degreesC to 60 degreesC. The polystyre...Neutral nickel sigma -acetylide complex [Ni(C=CPh)(2)(PBu3)(2)] is a novel initiator for the polymerization of styrene in CHCl3 over a range of polymerization temperature from 40 degreesC to 60 degreesC. The polystyrene obtained was a syndio-rich atactic polymer and its weight-average molecular weight reached 279000. The mechanism of the polymerization was discussed and a radical mechanism was proposed.展开更多
The copolymerization of styrene (St) with maleic anhydride (MAh) under gamma radiation at room temperature in the presence of benzyl dithiobenzoate (BDTB) was found to display 'living' nature evidenced by cons...The copolymerization of styrene (St) with maleic anhydride (MAh) under gamma radiation at room temperature in the presence of benzyl dithiobenzoate (BDTB) was found to display 'living' nature evidenced by constant concentration of chain radicals during the copolymerization, linear evolution of molecular weights with conversion and narrow molecular weight distribution (M-w/M-n = 1.23-1.35). The compositional analysis and the sequence structural information of the copolymers obtained from DEPT (Distortionless Enhancement by Polarization Transfer) experiments demonstrate that the copolymers obtained also possess strictly alternating structure.展开更多
The morphology effect of Zr-doped CeOwas studied in terms of their activities in the selective oxidation of styrene to styrene oxide using tert-butyl hydroperoxide as the oxidant. In the present work, Zrdoped CeOnanor...The morphology effect of Zr-doped CeOwas studied in terms of their activities in the selective oxidation of styrene to styrene oxide using tert-butyl hydroperoxide as the oxidant. In the present work, Zrdoped CeOnanorods exhibited the highest catalytic performance(yield of styrene oxide and TOF value)followed by nanoparticles and nanocubes. For the Zr-doped CeOnanorods, the apparent activation energy is 56.3 k J/mol, which is much lower than the values of catalysts supported on nanoparticles and nanocubes(73.3 and 93.4 k J/mol). The high resolution transmission electron microscopy results indicated that(100) and(110) crystal planes are predominantly exposed for Zr-doped CeOnanorods while(100)and(111) for nanocubes,(111) for nanoparticles. The remarkably increased catalytic activity of the Zrdoped CeOnanorods is mainly attributed to the higher percentage of Cespecies and more oxygen vacancies, which are associated with their exposed(100) and(110) crystal planes. Furthermore, recycling studies proved that the heterogeneous Zr-doped CeOnanorods did not lose its initial high catalytic activity after five successive recycles.展开更多
文摘Synthesis and characterization of the copolymers (PAG) of α-methyl styrene (AMS) and glycidyl methacrylate (GMA) are presented. The copolymers of PAG were characterized by gel permeation chromatography (GPC), Fourier transform infrared spectroscopy (FTIR), nuclear magnetic resonance (^1H-NMR) and thermogravimetery (TG). Based on the copolymer compositions determined by ^1H-NMR, the reactivity ratios of AMS and GMA were found to be 0.105 ± 0.012 and 0.883 ± 0.046 respectively by Kelen-Tudos method. TG revealed that thermal stability of the copolymers decreased with increasing the AMS content in the copolymers, which indicated that the degradation was mainly caused by the chain scission of AMS-containing structures. Under heating, the copolymers depolymerize at their weak bonds and form chain radicals, which could further initiate other chemical reactions.
文摘A phosphorus-containing monomer (lO-oxo-10-hydro-9-oxa-10λ^5-phosphaphenanthrene-10-yl)-methyl acrylate (MD was copolymerized with styrene to give a potential flame retardant copolymer of high thermal stability. The structures of monomer and copolymer were characterized by FT-IR and ^1H NMR measurements. The reactivity ratios for free-radical of the monomer (M1) and styrene (Mz) were studied. The calculated results are as follows: r1 = 0.225, r2 = 0.503; Q1 = 0.413, e1 = 0.476; azeotropic point = 0.37. TGA and DTG curves indicated that Ml is a potential flame retarding monomer for styrenic polymers. C 2009 Yu Bin Zheng. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.
基金financial supported by the National Natural Science Foundation of China (22078065)Key Program of Qingyuan Innovation Laboratory (00221001)Quanzhou City Science & Technology Program of China (2020C008R)。
文摘Catalytic epoxidation of alkenes is an important type of organic reaction in chemical industry,and the deep insight into catalyst deactivation will help to develop new epoxidation process.In this work,series of quaternary ammoniums bearing different cationic sizes,i.e.MTOA+(methyltrioctylammonium,[(C_(8)H_(17))_(3)CH_(3)N]+),HTMA+(hexadecyltrimethylammonium,[(C_(16)H_(33))(CH_(3))_(3)N]+) and DMDOA+(dimethyldioctadecylammonium,[(C_(18)H_(37))_(2)(CH_(3))_(2)N]+) were incorporated with polyoxometalate (POM) anions to prepare phase transfer catalysts (PTCs),which were used in the styrene epoxidations.Among them,(MTOA)_(3)PW_(4)O_(24)exhibits the best catalytic performance judged from the highest styrene conversion rate(52%) and styrene oxide selectivity (93%),during which the styrene epoxidation conditions were optimized.Meanwhile,the deactivation mechanism of this kind of PTCs was proposed firstly,i.e.in the case of low H_(2)O_(2) content,the oxidant can only be used in the styrene epoxidation,in which the catalyst can transform into stable Keggin-type POM.But when the content of H_(2)O_(2) is higher,the excess H_(2)O_(2) can reactivate the Keggin-type POM into active (PW_(4)O_(24))_(3)-anions,which can trigger the ring-opening polymerization of styrene oxide.Consequently,the catalyst is deactivated by adhered poly(styrene oxide)irreversibly,which was determined by NMR spectra.In this situation,the active moiety{PO_(4)[WO(O_(2))_(2)]_(4)}_(3)-in phase-transfer catalytic system can break into some unidentified species with low W/P ratio with the presence of epoxides.This work will be beneficial for the design of new PTCs in alkene epoxidation in fine chemical industry.
基金Supported by State Administration of Traditional Chinese Medicine High-level Key Discipline Construction Project of Traditional Chinese Medicine-Ethnic Minority Pharmacy (Zhuang Pharmacy) (zyyzdxk-2023165)General Scientific Research Program of Guangxi University of Chinese Medicine in 2020 (2020MS063)+4 种基金Key R&D Project of Guangxi Science and Technology Department (Guike AB21196057)Young Talent Cultivation Program of Guangxi International Zhuang Medicine Hospital (2022001)Funding Project of High-level Talent Cultivation and Innovation Team of Guangxi University of Chinese Medicine (2022A008)Guangxi Traditional Chinese Medicine Interdisciplinary Innovation Team Project (GZKJ2309)State Administration of Traditional Chinese Medicine"Twelfth Five-Year Plan"Key Discipline of Traditional Chinese Medicine (Ethnic Pharmacy)Zhuang Pharmacy.
文摘[Objectives]To establish a thin-layer chromatography(TLC)method for the determination of rubiadin-1-methyl ether in Yao Medicine Chuanlianzhu(Damnacanthus giganteus).[Methods]A silica gel G thin-layer plate was adopted for TLC.Petroleum ether(60-90℃)-chloroform-methanol-water(7:15:3:1)was used as the developing solvent and inspected under ultraviolet lamp(365 nm).The content was determined by Inertsil ODS-3 C 18 column(4.60 mm×250 mm,5μm),mobile phase:acetonitrile-0.2%phosphoric acid gradient elution,detection wavelength 277 nm,flow rate 1.0 mL/min,column temperature 30℃,injection volume 10μL.[Results]The spots of 10 Chuanlianzhu samples from different origins showed the same color at the same position as the control,and the spots were clear and specific.The injection volume of rubiadin-1-methyl ether showed a good linear relationship in the range of 2.90-145μg(R=0.9996).The average recovery rate of rubiadin-1-methyl ether in the low,medium and high dose groups of Yao Medicine Chuanlianzhu was 98.72%,and RSD=1.78%.[Conclusions]This method can effectively identify Yao Medicine Chuanlianzhu medicinal materials and accurately determine the content of rubiadin-1-methyl ether in the medicinal materials.It provides a scientific basis for the development and utilization of Yao Medicine Chuanlianzhu medicinal resources.
文摘Bottled water may not be safer, or healthier, than tap water. The present studies have proved that styrene and some other aromatic compounds leach continuously from polystyrene (PS) bottles used locally for packaging. Water sapmles in contact with PS were extracted by a preconcentration technique called as "purge and trap" and analysed by gas chromatograph-mass spectrometer (GC/MS). Eleven aromatic compounds were identified in these studies. Maximum concentration of styrene in PS bottles was 29.5 μg/L. Apart from styrene, ethyl benzene, toluene and benzene were also quantified but their concentrations were much less than WHO guide line values. All other compounds were in traces. Quality of plastic and storage time were the major factor in leaching of styrene. Concentration of styrene was increased to 69.53 μg/L after one-year storage. In Styrofoam and PS cups studies, hot water was found to be contaminated with styrene and other aromatic compounds. It was observed that temperature played a major role in the leaching of styrene monomer from Styrofoam cups. Paper cups were found to be safe for hot drinks.
基金Project supported by the National Basic Research Program of China (2004CB719500)the Commission of Science and Technology of Shanghai Municipality (03DJ14006)
文摘Using cetyl-trimethyl-ammonium bromide (CTMAB) as the template agent and tetraethylorthosilicate (TEOS) as the silica source, the MCM-41 mesoporous materials were synthesized with La or Ce incorporated in the framework under hydrothermal conditions. The structure and the state of La or Ce were investigated through the analyses of XRD, nitrogen adsorption-desorption, FT-IR, and UV-Vis. XRD and N2 adsorption-desorption results showed that Ln-MCM-41 exhibited the loss of the lattice ordering of the MCM-41 construct, and larger unit cell parameter and pore diameter than pure silica MCM-41. The FT-IR and UV-Vis results indicated the presence of isolated tetra-coordinated La or Ce ions in the framework and other Ln species dispersed highly on the Ln-MCM-41 surface simultaneously. Furthermore, their catalytic behaviors in the oxidation of styrene were studied using H2O2 as the oxidant. The La-MCM-41 catalysts exhibited high reactivity and the reactivity increased with the increase of the La content in the La-MCM-41 samples. On the contrary, Ce-MCM-41 catalysts showed low reactivity in the oxidation of styrene and the conversion of styrene decreased with the increase of the Ce content in the Ce-MCM-41 samples.
文摘The adsorption behavior and description behavior of benzene , ethylene and ethylbenzene over HZSM-5 and Co/HZSM-5 catalysts were studied by means of TPSR (Temperature programmed surface reaction) technique. TPSR results of ben- zene and ethylene co-adsorption show that the maian products are styrene , ethylben- zene, toluene, propane, and butane. In a separate experiment of ethylbenzene ad- sorption, styrene . toluene and benzene are formed due to cracking and dehydro- genation. The mechanism of styrene formation was proposed , i. e. , the reaction was carried out via. the dehydrogenation of mediate species ethylbenzene according to the results of TPSR-MS , activity testing and thermodynamic analysis.
基金This work was supported by the National Natural Science Foundation of China (No. 20177004, 20507004).
文摘Sulfur hexafluoride (SF6) is known as one of the most powerful greenhouse gases in the atmosphere. Reductive photodegradation of SF6 by styrene has been studied with the purpose of developing a novel remediation for sulfur hexafluoride pollution. Effects of reaction conditions on the destruction and removal efficiency (DRE) of SF6 are examined in this study. Both initial styrene-to-SF6 ratio and initial oxygen concentration exert a significant influence on DRE. SF6 removal efficiency reaches a maximum value at the initial styrene-to-SF6 ratio of 0.2. It is found that DRE increases with oxygen concentration over the range of 0 to 0.09 mol/m^3 and then decreases with increasing oxygen concentration. When water vapor is fed into the gas mixture, DRE is slightly enhanced over the whole studied time scale. The X-ray Photoelectron Spectroscopy (XPS) analysis, together with gas chromatography-mass spectrometry (GC-MS) and Fourier Transform Infrared spectroscopy (FT-IR) analysis, prove that nearly all the initial fluorine residing in the gas phase is in the form of SiF4, whereas, the initial sulfur is deposited in the form of elemental sulfur, after photodegradation. Free from toxic byproducts, photodegradation in the presence of styrene may serve as a promising technique for SF6 abatement.
文摘Emulsion copolymerization of styrene and ethylene catalyzed by a series of neutral nickel(Ⅱ) complexes was carried out in an aqueous system to give high-molecular-weight copolymers.The copolymers and emulsions were characterized by an array of techniques including NMR,GPC,TEM,WAXD and DSC.The results indicate that the copolymers obtained are mostly block copolymers of polyethylene with random insertion of styrene units,and their M_W is in the range of 10~5-10~6.By enhancing the electron withdrawing of the s...
基金This project was supported by the National Natural Science Foundation of China. (No.29974024,20254001)
文摘Copolymerization of styrene (St) with N-phenylmaleimide (NPMI) was studied with rare earth coordination catalyst Nd(naph)3-AlEt3 in toluene. Characterization of the copolymers showed that the copolymers possess an alternating structure.
基金supported by the Major State Basic Research Program of China (No. 2009CB623404) National Natural Science Foundation of China (Nos. 20736003, 20676067)+2 种基金 National High Technology Research and Development Program of China (No. 2007AA06Z317)Foundation of Ministry of Education of China (No. 20070003130)Foundation of the State Key Laboratory of Chemical Engineering (No. SKL-ChE-08A01)
文摘In order to control the surface pore sizes of polyvinylidene fluoride membranes and their distribution, low temperature plasma-induced grafting modifications of PVDF were studied to prepare hydrophobe membranes. By argon (Ar) treating and subsequent grafting reaction, a hydrophobe monomer, styrene, was introduced into the PVDF membrane. Fourier transform infrared attenuated total reflection (FTIR-ATR) was utilized to characterize the chemical and physical changes in the Ar plasma modified membrane. The surface modifications of PVDF membranes were investigated by using scanning electron microscopy (SEM), atomic force microscopy (AFM) and differential scanning calorimeter (DSC). The water permeability and the solute rejection were measured by PVDF membrane modified in different graft conditions. Results demonstrated that the pores in the modified membranes get smaller and the distribution of pores gets narrowed with the increase in grafting reaction duration. Longer graft time caused the water flux of PVDF membrane to decrease from 578 kg/(m^2· h) to 23 kg/(m^2· h) and the solute rejection to increase from 73% to 92%.
基金Science Technology Foundation of Jilin Province (200223)
文摘The catalytic activity of poly(styrene-acrylic acid) (PSAA) supported neodymium chloride (NdCl3) complex for the copolymerization of styrene and 4-Vinylpyridine was studied. The influence of various factors, such as Al/Nd molar ratio, reaction time, macromolecular carder (PSAA), and ratio of styrene to 4-vinypyridine (g/g), on the copolymerization yield of styrene and 4-Vinylpyridine was investigated. The results showed that the copolymerization of polar monomers with olefins occurred efficiently and the catalytic activity of polymer-supported catalyst was higher than that of the similar small molecular catalysts. The activity of PSAA.Nd complex increased with in- creasing Al/Nd molar ratios and decreased with increasing polymerization time. The highest activity of PSAA'Nd was observed at 120 min, and the highest yield was found at the ratio of styrene to 4-vinylpyridine of 4:2. DSC analysis presented that the resulted polymer had only one glass transition temperature, and showed very good thermal stability.
基金supported by National Natural Science Foundation of China(No.50573005)
文摘A new kind of multifunctional macromolecular initiator with Sn-C bonds and polydiene arms was synthesized by living anionic polymerization. At first, polydiene-stannum chloride (PD-SnCl3) was prepared by the reaction of n-butyl-Li (n-BuLi), stannic chloride (SnCl4) and diene. Then PD-SnCl3 was used to react with the dilithium initiator to prepare the multifunctional organic macromolecular initiators. The result suggested that the initiators had a remarkable yield by GPC, nearly 90%. By using these multifunctional macromolecular initiators, styrene and butadiene were effectively polymefized via anionic polymerization, which gave birth to novel miktoarm star copolymers. The relative molecular weight and polydispersity index, microstructure contents, copolymerization components, glass transition temperature (Tg) and morphology of the miktoarm star copolymers were investigated by GPC-UV, ~H NMR, DSC and TEM, respectively. 2009 Xing Ying Zhang. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.
基金supported by the National Natural Science Foundation of China(no.21206202)Scientific and Technological Research Program of Chongqing Municipal Education Commission(no.KJ1600902)+2 种基金the Demonstration project of Chongqing"121"Scientific&Technological Support Project(CSTC2014zktjccx BX0089)Project of Key generic industry technologies of Chongqing(No.cstc2016zdcy-ztzx0020-02)Program for Innovative Research Team in Chongqing University of Technology(2015TD22)
文摘The new V-MCM-41 molecular sieves with good ordered hexagonal mesoporous structure and crystallinity were synthesized through in-situ hydrothermal preparation method. The effects of the crystallization time were discussed. The synthesized samples were characterized by X-ray diffraction, N2adsorption/desorption, Fourier transformed infrared and scanning electron microscopy. The different structures, textures, morphologies of V-MCM-41 obtained with different crystallization times were observed and analyzed on the basis of the characterized results. The results showed that the V-MCM-41 molecular sieve obtained at 110?°C for 48?h crystallization times was of good spherical morphology, ordered hexagonal structure, most uniform pore size distribution and high surface area compared with other samples. Meanwhile, the V-MCM-41 molecular sieve with the high skeleton Si condensation and the good crystallinity was obtained. The heteroatom could be incorporated into MCM-41 framework with increasing crystallization times, which was beneficial to improve the catalytic activity and selectivity of pure siliceous MCM-41. The V-MCM-41 showed the good catalytic selectivity in catalytic oxidation of styrene using hydrogen peroxide, and the selectivity of the benzaldehyde and phenylacetic acid reached 30.68% and 49.44%, respectively. ? 2016
文摘The polymerization behaviors of Styrene (St) in the presence of CuX/L [X=Cl or Br; L= 2,2 bipyridine (bpy), 1,10 phenanthroline (phen) or 4,7 diphenyl 1,10 phenanthroline (DPP) ] and R X (R=trichloromethyl, benzyl or allyl; X=Cl or Br) have been studied and examined. In a CuCl/bpy/RCl/St system, a bimodal GPC peak at the early stage of polymerization was observed, and a concept of multi active species was proposed to explain this phenomenon. In a CuCl/phen (DPP)/RCl/St system, the \%M\%\-n of polystyrene (PS) increased linearly with St conversion and ln[M] o/[M] also increased linearly with time, indicating the living nature of this system. Furthermore, the stability of the propagating active species in a CuBr/phen/RBr/St system is higher than that in the CuBr/phen/RBr/St system.
基金Project supported by the Fundacā de Amparo à Pesquisa do Estado de Sāo Paulo and CNPq Conselho Nacional de Desenvolvimento Científico e Teenológico
文摘The synthesis of organolanthanide compounds identified as LnCp^*(MS)2PzA, Ln = Sm, Tb, Yb (MS = methanesulfonate, Cp^* = pentamethylcyclopentadienyl, and PzA = pyrazinamide), by the reaction of coordination compounds Ln(MS)3(PzA)4 with NaCp in THF was reported. The complexes were formulated according to elemental analyses, complexometric titration with EDTA (%Ln), and ^1H NMR. IR spectroscopy revealed that PzA coordinates with lanthanide (Ⅲ) ions and methanesulfonate coordinates via oxygen atoms in a non-equivalent manner. In preliminary catalytic studies, these compounds were active in styrene polymerization that used MAO as a cocatalyst with an activity of 12.3 kg PS molSm^-1h^-1. Differential scanning calorimetry (DSC) of polystyrene showed that the polymer was mainly atactic.
基金We are grateful for the financial support from the National Natural Science Foundation of China(Grant no.29906001).
文摘Thermoregulated phase-separable Ru3(CO)12/PETPP (PETPP=P[p-C6H4O (CH2CH2O)n H]3, n=6) complex catalyst was first applied in the hydrogenation of styrene. Under the conditions: P(H2)=2.0MPa, T=90C, styrene could be completely transferred and the yield of ethylbenzene reached up to 99.5%. After simple decantation, the catalyst could be reused for ten times without decreasing in activity.
文摘Neutral nickel sigma -acetylide complex [Ni(C=CPh)(2)(PBu3)(2)] is a novel initiator for the polymerization of styrene in CHCl3 over a range of polymerization temperature from 40 degreesC to 60 degreesC. The polystyrene obtained was a syndio-rich atactic polymer and its weight-average molecular weight reached 279000. The mechanism of the polymerization was discussed and a radical mechanism was proposed.
文摘The copolymerization of styrene (St) with maleic anhydride (MAh) under gamma radiation at room temperature in the presence of benzyl dithiobenzoate (BDTB) was found to display 'living' nature evidenced by constant concentration of chain radicals during the copolymerization, linear evolution of molecular weights with conversion and narrow molecular weight distribution (M-w/M-n = 1.23-1.35). The compositional analysis and the sequence structural information of the copolymers obtained from DEPT (Distortionless Enhancement by Polarization Transfer) experiments demonstrate that the copolymers obtained also possess strictly alternating structure.
基金the financial support from NNSFC(Project 21373054,21303023,21173052)the Natural Science Foundation of Shanghai Science and Technology Committee(08DZ2270500)
文摘The morphology effect of Zr-doped CeOwas studied in terms of their activities in the selective oxidation of styrene to styrene oxide using tert-butyl hydroperoxide as the oxidant. In the present work, Zrdoped CeOnanorods exhibited the highest catalytic performance(yield of styrene oxide and TOF value)followed by nanoparticles and nanocubes. For the Zr-doped CeOnanorods, the apparent activation energy is 56.3 k J/mol, which is much lower than the values of catalysts supported on nanoparticles and nanocubes(73.3 and 93.4 k J/mol). The high resolution transmission electron microscopy results indicated that(100) and(110) crystal planes are predominantly exposed for Zr-doped CeOnanorods while(100)and(111) for nanocubes,(111) for nanoparticles. The remarkably increased catalytic activity of the Zrdoped CeOnanorods is mainly attributed to the higher percentage of Cespecies and more oxygen vacancies, which are associated with their exposed(100) and(110) crystal planes. Furthermore, recycling studies proved that the heterogeneous Zr-doped CeOnanorods did not lose its initial high catalytic activity after five successive recycles.