SiC powder was rapidly synthesized in an induction furnace with crystalline silicon cutting waste and active carbon as raw materials,and then SiC porous ceramics were prepared at 1600 t for 4 h with carbon embedded us...SiC powder was rapidly synthesized in an induction furnace with crystalline silicon cutting waste and active carbon as raw materials,and then SiC porous ceramics were prepared at 1600 t for 4 h with carbon embedded using the powder as raw material,the starch and the graphite as pore-forming agents.Effects of additions of different pore-forming agents on the phase composition,microstructures,physical properties,and cold crushing strength of the porous ceramics were investigated.The results show that the main crystalline phases of the synthetic powder areα-S iC(6H-SiC)andβ-SiC(3C-SiC).The phase composition of the porous ceramics includesα-S iC(6H-SiC),β-SiC(3C-SiC),FeSi,quartz and Si2N20.The apparent porosity and closed porosity of the porous ceramics prepared by adding starch are higher,and the cold compressive strength of the porous ceramics added with graphite is higher.As increasing the additions of the starch,the apparent porosity,closed porosity and linear shrinkage ratio of the porous ceramics increase,and the bulk density decreases correspondingly.When 20 mass%starch is added,the apparent porosity,closed porosity,linear shrinkage ratio and cold compressive strength are 57.05%,2.03%,5.10%and 10.20 MPa,respectively.展开更多
Isotactic polypropylene (iPP) with high content of ~ crystalline form was prepared by adding a series of new p form nucleators. The spherulites and morphology of//farm iPP (//-iPP) were investigated by wide-angle X-ra...Isotactic polypropylene (iPP) with high content of ~ crystalline form was prepared by adding a series of new p form nucleators. The spherulites and morphology of//farm iPP (//-iPP) were investigated by wide-angle X-ray diffraction(WAXD), polarizing microscope (PLM), scanning electron microscope (SEM) and small-angle light scattering (SALS). WAXD experimental results indicate that the amount of p form in iPP (K_x) increases with increasing /~ nucleator content from zero to 0.07 wt% or crystallization temperature T_c from 20 to 120℃ and that the highest K_x value is up to 0.95. PLM observations suggest that p spherulites exhibit bright color and that their Maltese Crosses display some concentric banding of a rather spiky, jagged character. Their !amellae are smooth and relaxed layer-plate like structure by SEM and their SALS H_v patterns arc four-petalled.展开更多
The melting behavior of polypropylene (PP) and low ethylene content polypropylenecopolymer with and without nucleating agent samples crystallized under both isothermal and non-isothermal conditions were studied by Dif...The melting behavior of polypropylene (PP) and low ethylene content polypropylenecopolymer with and without nucleating agent samples crystallized under both isothermal and non-isothermal conditions were studied by Differential Scanning Calorimeter (DSC) and X-raydiffraction. Multiple melting behavior were observed depending on the existence of nucleatingagent and crystallization conditions. The observed phenomena have been discussed by the effect ofnucleating agent on perfection of crystal and the melting and recrystallization of imperfect crystalto a more perfect crystal during the heating process of samples.展开更多
SiC porous ceramics were prepared at 1 400 ℃ for4 h with crystalline silicon cutting waste and activated carbon as main starting materials and NH4HCO3 as the pore-forming agent. Effects of NH4HCO3 additions( 0,20%,30...SiC porous ceramics were prepared at 1 400 ℃ for4 h with crystalline silicon cutting waste and activated carbon as main starting materials and NH4HCO3 as the pore-forming agent. Effects of NH4HCO3 additions( 0,20%,30%,40%,by mass) on the phase composition,microstructure,sintering properties,cold compressive strength and thermal shock resistance of as-prepared Si C porous ceramics were investigated. The results show that:( 1) addition of NH4HCO3 remarkably influences the apparent porosity and cold compressive strength of specimens. The apparent porosity achieves its maximum value( 63. 40%) when 40% NH4HCO3 is added,while the minimum cold compressive strength is 4. 77 MPa;( 2) the specimen with 40% NH4HCO3 has the best thermal shock resistance. The thermal cycling times between1 000 ℃ to room temperature reach 62;( 3) the addition of NH4HCO3 does not remarkably affect the phase composition of the specimens;( 4) the specimens include a large number of SiC particles and a small amount of SiC whiskers.展开更多
通过酰胺化合物(NA-BW)引导等规聚丙烯(iPP)制备高水平β晶型聚丙烯(β-iPP),借助广角X射线衍射(WAXD),差示扫描量热仪(DSC)及偏光显微镜(POM)研究其结晶形态及结晶行为,并研究了β型成核剂对iPP力学性能的影响。结果表明:加入β型成核...通过酰胺化合物(NA-BW)引导等规聚丙烯(iPP)制备高水平β晶型聚丙烯(β-iPP),借助广角X射线衍射(WAXD),差示扫描量热仪(DSC)及偏光显微镜(POM)研究其结晶形态及结晶行为,并研究了β型成核剂对iPP力学性能的影响。结果表明:加入β型成核剂NA-BW后,iPP的晶型和球晶形态均发生变化;等温结晶研究表明聚丙烯的半结晶时间(t1/2)明显降低,即结晶速度加快,非等温结晶研究表明iPP的结晶温度提高;iPP的冲击强度大大提高,拉伸和弯曲性能却略有下降。当成核剂用量为3 m g/g时,悬臂梁缺口冲击强度达到最大值,提高达3.5倍,由49.35J/m提高到176.23 J/m。热稳定性实验表明β型成核剂对聚丙烯成核效果的热稳定性良好。展开更多
文摘SiC powder was rapidly synthesized in an induction furnace with crystalline silicon cutting waste and active carbon as raw materials,and then SiC porous ceramics were prepared at 1600 t for 4 h with carbon embedded using the powder as raw material,the starch and the graphite as pore-forming agents.Effects of additions of different pore-forming agents on the phase composition,microstructures,physical properties,and cold crushing strength of the porous ceramics were investigated.The results show that the main crystalline phases of the synthetic powder areα-S iC(6H-SiC)andβ-SiC(3C-SiC).The phase composition of the porous ceramics includesα-S iC(6H-SiC),β-SiC(3C-SiC),FeSi,quartz and Si2N20.The apparent porosity and closed porosity of the porous ceramics prepared by adding starch are higher,and the cold compressive strength of the porous ceramics added with graphite is higher.As increasing the additions of the starch,the apparent porosity,closed porosity and linear shrinkage ratio of the porous ceramics increase,and the bulk density decreases correspondingly.When 20 mass%starch is added,the apparent porosity,closed porosity,linear shrinkage ratio and cold compressive strength are 57.05%,2.03%,5.10%and 10.20 MPa,respectively.
文摘Isotactic polypropylene (iPP) with high content of ~ crystalline form was prepared by adding a series of new p form nucleators. The spherulites and morphology of//farm iPP (//-iPP) were investigated by wide-angle X-ray diffraction(WAXD), polarizing microscope (PLM), scanning electron microscope (SEM) and small-angle light scattering (SALS). WAXD experimental results indicate that the amount of p form in iPP (K_x) increases with increasing /~ nucleator content from zero to 0.07 wt% or crystallization temperature T_c from 20 to 120℃ and that the highest K_x value is up to 0.95. PLM observations suggest that p spherulites exhibit bright color and that their Maltese Crosses display some concentric banding of a rather spiky, jagged character. Their !amellae are smooth and relaxed layer-plate like structure by SEM and their SALS H_v patterns arc four-petalled.
文摘The melting behavior of polypropylene (PP) and low ethylene content polypropylenecopolymer with and without nucleating agent samples crystallized under both isothermal and non-isothermal conditions were studied by Differential Scanning Calorimeter (DSC) and X-raydiffraction. Multiple melting behavior were observed depending on the existence of nucleatingagent and crystallization conditions. The observed phenomena have been discussed by the effect ofnucleating agent on perfection of crystal and the melting and recrystallization of imperfect crystalto a more perfect crystal during the heating process of samples.
文摘SiC porous ceramics were prepared at 1 400 ℃ for4 h with crystalline silicon cutting waste and activated carbon as main starting materials and NH4HCO3 as the pore-forming agent. Effects of NH4HCO3 additions( 0,20%,30%,40%,by mass) on the phase composition,microstructure,sintering properties,cold compressive strength and thermal shock resistance of as-prepared Si C porous ceramics were investigated. The results show that:( 1) addition of NH4HCO3 remarkably influences the apparent porosity and cold compressive strength of specimens. The apparent porosity achieves its maximum value( 63. 40%) when 40% NH4HCO3 is added,while the minimum cold compressive strength is 4. 77 MPa;( 2) the specimen with 40% NH4HCO3 has the best thermal shock resistance. The thermal cycling times between1 000 ℃ to room temperature reach 62;( 3) the addition of NH4HCO3 does not remarkably affect the phase composition of the specimens;( 4) the specimens include a large number of SiC particles and a small amount of SiC whiskers.
文摘通过酰胺化合物(NA-BW)引导等规聚丙烯(iPP)制备高水平β晶型聚丙烯(β-iPP),借助广角X射线衍射(WAXD),差示扫描量热仪(DSC)及偏光显微镜(POM)研究其结晶形态及结晶行为,并研究了β型成核剂对iPP力学性能的影响。结果表明:加入β型成核剂NA-BW后,iPP的晶型和球晶形态均发生变化;等温结晶研究表明聚丙烯的半结晶时间(t1/2)明显降低,即结晶速度加快,非等温结晶研究表明iPP的结晶温度提高;iPP的冲击强度大大提高,拉伸和弯曲性能却略有下降。当成核剂用量为3 m g/g时,悬臂梁缺口冲击强度达到最大值,提高达3.5倍,由49.35J/m提高到176.23 J/m。热稳定性实验表明β型成核剂对聚丙烯成核效果的热稳定性良好。
