15 nm Bulk nFinFET器件性能研究及参数优化

为研究Bulk FinFET工作时基本结构参数、器件温度和栅极材料对其性能的影响,建立了一个15 nm n型Bulk FinFET器件模型,仿真分析了不同栅长、鳍宽、鳍高、沟道掺杂浓度、器件工作温度、栅极材料对器件性能的影响,发现增长栅长、降低鳍宽和增加鳍高有助于抑制短沟道效应;1×10^(17)cm^(-3)以下的低沟道掺杂浓度对器件特性影响不大,但高掺杂会使器件失效;器件工作温度的升高会导致器件性能的下降;采用高K介质材料作为栅极器件性能优于传统材料SiO_(2)。

袋型阻尼密封动力学特性双控制体Bulk Flow模型

为快速准确预测袋型阻尼密封泄漏特性和动力学特性,针对传统单控制体Bulk Flow模型预测精度低、无法预测交叉动力系数的问题,提出了袋型阻尼密封双控制体Bulk Flow模型和动力学特性数值预测方法,并开发了计算程序。首先,依据边界层理论,将袋型密封腔室划分为两个控制体,推导了控制体的连续性、周向动量和能量方程,引入Swamee-Jain和Takahashi方程,计算流体-壁面间和流体-流体间的周向黏性摩擦力;其次,采用牛顿-拉夫森算法和摄动分析法分别求解0阶和1阶控制方程,获得各刚度、阻尼动力特性系数;然后,通过与袋型阻尼密封泄漏量和动力特性系数的实验值、单控制体Bulk Flow模型和非定常计算流体动力学(CFD)数值结果进行比较,验证了模型和方法的准确性和可靠性;最后,研究了转子转速(10 000、15 000、20 000 r/min)和预旋比(0.067、0.724、0.997)对袋型阻尼密封动力学特性的影响。结果表明:所发展的模型和方法具有计算速度快、预测精度高(泄漏量预测误差小于6%,动力特性系数预测误差小于38%)的优点;转子转速和进口预旋的增大均会导致袋型阻尼密封有效阻尼显著减小,穿越频率显著增大,易诱发轴系失稳。

Comparative Study on Super Fine Mesophase Powder and MCMB Used to Manufacture High-Density Isotropic Carbon Bulks

Mesocarbon microbeads （MCMB） and super fine mesophase powder （SFMP） were prepared firstly from a coal tar pitch and then hot-condensed into high-density isotropic carbon （HDIC） bulks under 160 MPa and finally sintered at 1 000 ℃. By analyzing the thermogravimetric behavior of the MCMB and SFMP powders, their volume shrinkage and weight loss during sintering and the bulk density and flexural strengths of their sintered bulks, it was found that the smaller sizes and the richer β-resin contents of SFMP ha）re facilitated formation of sintered bulks with more compact isotropic structure and higher flexural strengths than MCMB. Because of the filling and bonding effects of SFMP on MCMB bulks, addition of SFMP, albeit a little, can greatly increase the flexural strengths of sintered bulks of MCMB. However, adding MCMB, even a slight amount, into SFMP can severely impair the flexural strength of sintered bulks. This might be attributed to both the crack initiation along the boundaries between MCMB and SFMP and the formation of layered texture of MCMB sphere.

Structure and properties of nanocrystalline rare earth bulks prepared by spark plasma sintering

A series of rare earth bulks with the ultrafine nanocrystalline structure were prepared by applying an 'oxygen-free'(an environmental oxygen concentration less than 0.5 ppm) in-situ synthesis system,where the inert-gas condensation was combined with the spark plasma sintering technology into an entirely closed system.The thermal and mechanical properties of the prepared ultrafine nanocrystalline bulks were characterized and compared with those of the raw polycrystalline bulks.It was found that the specific ...

Fast joining YBCO bulks with melt Ag doped Y-Ba-Cu-O solder

Y-Ba-Cu-O is a promising high temperature superconductor material because of its good electrical and magnetic properties. However, large and complex bulks cannot be made directly, and joining is a good way to solve this problem. Joining Y-Ba-Cu-O with filler material was widely used and reported, but sliced melt solder was rarely reported, especially the one that required relatively short time. In this paper, sliced melt Ag doped Y-Ba-Cu-O was used as filler material and the joining time is relatively shorter compared with mast of the published paper. The melt solder was fabricated and tested, the melting temperature is 975℃and there is much less pores found in the solder compared with the sintered solder. The bonding result is very encouraging： the superconductivity recovery ratio is 97.3%, which is about 5% higher than as sintered filler material. The microstructure in the bonding zone is very similar to that in the base material, no Y2BaCuO5 （ Y211 ） phase accumulated during the joining process, which reveals that high quality superconductive bonding was achieved.

Review:Recent Progress on the Application of REBCO Superconductor Bulks

The high temperature superconducting REBa2 Cu3 O7-x(REBCO)bulk with a diameter of only a few centimeters can trap a tesla⁃level magnetic field at a moderate temperature.The high magnetic field in such a compact structure makes the REBCO bulk magnet widely applicable in many scenarios,such as in motor,generator,and bearing for flywheel.This review focuses on some research areas using the REBCO bulk magnet,which is quite interesting but has attracted little attention,including magnet lens,compact NMR,magnetron sputtering system,drug magnetic targeting system,magnetic separation,and magnetic mirror.In all of these areas,the REBCO bulk magnet shows its own advantages of having a high magnetic field but a small size to improve the final function.

Towards high degree of c-axis orientation in MgB_(2) bulks

The paper presents fabrication and characterization of spark plasma sintered textured(001) MgB_(2)with a record degree of orientation of about 40% and 16% by high-energy ultra-sonication and slip casting in high magnetic field(12 T) and 0 T magnetic field, respectively.Structural characterization was performed by X-ray diffraction, and electron microscopy. The analysis revealed unexpected preferred orientation also in the MgO secondary phase due to the epitaxial growth of(111) MgO on(001) MgB_(2). The influence of oriented microstructure on the superconducting characteristics expressed by critical current density(J_(c)), irreversibility field(H_(irr)), and on the pinning properties were assessed. High anisotropy versus sample orientation in applied magnetic field, H, was observed for J_(c), Hirr, pinning activation energy(U^(*))extracted from relaxation measurements. The zero-field critical current, J_(c0)and F_(p),maxare weakly or not dependent on the direction of H,while the other indicated parameters are significantly influenced. Results enable control of superconducting parameters by further optimization of microstructure through MgB_(2) texturing as a novel and viable strategy for development of bulk MgB2with enhanced properties when taking advantage of its anisotropy.

Preparation of nano-structured pure rare-earth bulks by combining inert-gas condensation with SPS

A number of techniques have been developed to synthesize nanocrystalline bulk materials,including inert-gas condensation and consolidation,electrodeposition,severe plastic deformation,crystallization of amorphous solid,surface mechanical attrition,and powder metallurgy.However,it is hard to produce the bulk with controllable nanostructures,especially with the grain sizes controllable in a wide range below 100 nm.In the conventional powder metallurgy,due to the fact that rapid coarsening of the particles ...

Anisotropic Band Evolution of Bulk Black Phosphorus Induced by Uniaxial Tensile Strain

We investigate the anisotropic band structure and its evolution under tensile strains along different crystallographic directions in bulk black phosphorus(BP)using angle-resolved photoemission spectroscopy and density functional theory.The results show that there are band crossings in the Z-L(armchair)direction.

Influences of polymorphism of packed particles on bulk characterizations in fluidization realm

The characterization of a particle ensemble(rather than a single particle) is of paramount significance to various particle technologies and has long been a fundamental subject in the fluidization realm. However, many of such bulk characterizations as loosely-packed density(ρbl), minimum fluidization velocity(Umf), sphericity(φ), discharge rate through orifice(q), angle of repose(β), and segregation index(S),were found to be poorly reproducible, making the reported results seldom comparable. Since these bulk characterizations started from the packed state of particles, such poor reproducibility was ascribed to the polymorphism of packed particles in this work. We observed that in the fluidized bed, the settled/packed state of particles varied monotonously with the settling rate(a) from complete fluidization to zero. This phenomenon confirmed the polymorphic characteristic of packed particles and further enabled us to systematically disclose/clarify its influences on the aforementioned bulk characterizations. Such influences could be comprehensively and intuitively reflected by the impacts induced by a. With the decrease of a, ρbl, φ and q first increased, then decreased, and finally leveled off while Umfand β showed an opposite trend. On the other hand, S first increased and then remained invariant. As per these findings and definitions of these bulk characterizations, benchmarks were indicated to unify the selection of settled state among future scholars and further make their outcomes become fairly comparable. Additionally, most packed states of the particle ensemble were proved to be metastable with their formation and behavior being identical to those of the amorphous state.

“Glass-quake”in elastically loaded bulk metallic glasses

Amorphous solids exhibit scale-free avalanches,even under small external loading,and thus can work as suitable systems to study critical behavior and universality classes.The abundance of scale-free avalanches in the entire elastic tension regime of bulk metallic glass(BMG)samples has been experimentally observed using acoustic emission(AE)measurements.In this work,we compare the statistics of avalanches with those of earthquakes,and find that they both follow the Gutenberg–Richter law in the statistics of energies and Omori’s law of aftershock rates,and share the same characteristics in the distribution of recurrence times.These resemblances encourage us to propose the term“glass-quake”to describe avalanches in elastically loaded BMGs.Furthermore,our work echoes the potential universality of critical behavior in disordered physical systems from atomic to planetary scales,and motivates the use of elastic loaded BMGs as valuable laboratory simulators of seismic dynamics.

Bulk geochemistry,Rb-Sr,Sm-Nd,and stable O-H isotope systematics of the Metzimevin high-grade iron ore deposit,Mbalam iron ore district,southern Cameroon

Bulk geochemistry,Sr,Nd,and O-H isotope systematics are reported for the first time on banded iron formation(BIF)-hosted high-grade iron ore at the northwestern segment of Congo Craton(CC).Located in Mbalam iron ore district,Southern Cameroon,Metzimevin iron ore deposit is a hematite-magnetite BIF system,dominated by SiO_(2)+Fe_(2)O_(3)(97.1 to 99.84 wt%),with low concentrations of clastic elements e.g.,Al_(2)O_(3),TiO_(2),and HFSE,depicting a nearly pure chemical precipitate.The REE+Y signature of the iron deposit displays strong positive Eu anomaly,strong negative Ce anomaly,and chondritic to superchondritic Y/Ho ratios,suggestive of formation by mixed seawater-high temperature hydrothermal fluids in oxidising environment.The^(87)Sr/^(86)Sr ratios of the BIF are higher than the maximum^(87)Sr/^(86)Sr evolution curves for all Archean reservoirs(bulk silicate earth,Archean crust and Archean seawater),indicating involvement of continentally-derived components during BIF formation and alteration.TheƐ_(Nd)(t)(+2.26 to+3.77)and Nd model age indicate that chemical constituents for the BIF were derived from undifferentiated crustal source,between 3.002 and 2.88 Ga.The variable and diverse O and H isotope data(−1.9‰to 17.3‰and−57‰to 136‰respectively)indicate that the Metzimevin iron ore formed initially from magmatic plumes and later enriched by magmatic-metamorphic-modified meteoric fluids.Mass balance calculations indicate mineralisation by combined leaching and precipitation,with an average iron enrichment factor of>2.67 and SiO_(2)depletion factor of>0.99.This is associated with an overall volume reduction of 28.27%,reflecting net leaching and volume collapse of the BIF protholith.

A bulk extraction method to determine the stable isotope ratios of iron,nickel,copper,zinc,and cadmium in seawater using multi-collector inductively coupled plasma mass spectrometry

The oceanic trace metals iron(Fe),nickel(Ni),copper(Cu),zinc(Zn),and cadmium(Cd)are crucial to marine phytoplankton growth and global carbon cycle,and the analysis of their stable isotopes can provide valuable insights into their biogeochemical cycles within the ocean.However,the simultaneous isotopic analysis of multiple elements present in seawater is challenging because of their low concentrations,limited volumes of the test samples,and high salt matrix.In this study,we present the novel method developed for the simultaneous analysis of five isotope systems by 1 L seawater sample.In the developed method,the NOBIAS Chelate-PA1 resin was used to extract metals from seawater,the AG MP-1M anion-exchange resin to purify Cu,Fe,Zn,Cd,and the NOBIAS Chelate-PA1 resin to further extract Ni from the matrix elements.Finally,a multi-collector inductively coupled plasma mass spectroscope(MC-ICPMS)was employed for the isotopic measurements using a doublespike technique or sample-standard bracketing combined with internal normalization.This method exhibited low total procedural blanks(0.04 pg,0.04 pg,0.21 pg,0.15 pg,and 3 pg for Ni,Cu,Fe,Zn,and Cd,respectively)and high extraction efficiencies(100.5%±0.3%,100.2%±0.5%,97.8%±1.4%,99.9%±0.8%,and 100.1%±0.2%for Ni,Cu,Fe,Zn,and Cd,respectively).The external errors and external precisions of this method could be considered negligible.The proposed method was further tested on the seawater samples obtained from the whole vertical profile of a water column during the Chinese GEOTRACES GP09 cruise in the Northwest Pacific,and the results showed good agreement with previous related data.This innovative method will contribute to the advancement of isotope research and enhance our understanding of the marine biogeochemical cycling of Fe,Ni,Cu,Zn,and Cd.

单细胞测序与Bulk RNA测序联合分析构建膀胱癌风险预后模型

目的本研究致力于开发一种基于膀胱癌核心细胞差异性表达基因的预后风险评估模型。通过在多个数据集中验证其效力,旨在为膀胱癌患者提供一个新的临床应用工具,用于预后风险评估。方法本研究综合利用了单细胞和Bulk RNA测序数据。我们首先从GEO数据库下载并分析了相关的膀胱癌单细胞和芯片RNA数据集。通过生物信息学方法,我们鉴定了核心细胞的差异性表达基因,并对其进行了功能及通路富集分析。基于这些分析,我们使用单变量和多变量Cox回归方法筛选出与膀胱癌预后显著相关的关键基因,并据此构建了一个预后风险评估模型。该模型在TCGA-BLCA数据集中进一步进行了效力验证。结果经过全面的生物信息学分析,我们鉴定出了223个核心细胞的差异性表达基因。这些基因在细胞外基质的结构和功能方面发挥着重要作用。构建的预后风险评估模型包括5个独立的预后相关基因(MFAP5、PDE4D、ISG15、ADAMTS1和FGL2)。在GEO和TCGA-BLCA数据集中的验证结果表明,该模型具有良好的预测效力,为膀胱癌患者的预后评估提供新型生物学标志工具。结论本研究成功开发了一个基于5个关键基因标志物的膀胱癌预后风险评估模型并具有良好的预测效力。此模型的开发为膀胱癌的生物学研究和临床预后评估提供了一个新的工具,有助于更好地理解膀胱癌的生物学特性并指导患者的个性化治疗。

Thermodynamics-directed bulk/grain-boundary engineering for superior electrochemical durability of Ni-rich cathode

Introducing high-valence Ta element is an essential strategy for addressing the structu ral deterioration of the Ni-rich LiNi_(1-x-y)Co_(x)Mn_(y)O_(2)(NCM)cathode,but the enlarged Li/Ni cation mixing leads to the inferior rate capability originating from the hindered Li~+migration.Note that the non-magnetic Ti~(4+)ion can suppress Li/Ni disorder by removing the magnetic frustration in the transition metal layer.However,it is still challenging to directionally design expected Ta/Ti dual-modification,resulting from the complexity of the elemental distribution and the uncertainty of in-situ formed coating compounds by introducing foreign elements.Herein,a LiTaO_3 grain boundary(GB)coating and bulk Ti-doping have been successfully achieved in LiNi_(0.834)Co_(0.11)Mn_(0.056)O_(2) cathode by thermodynamic guidance,in which the structural formation energy and interfacial binding energy are employed to predict the elemental diffusion discrepancy and thermodynamically stable coating compounds.Thanks to the coupling effect of strengthened structural/interfacial stability and improved Li~+diffusion kinetics by simultaneous bulk/GB engineering,the Ta/Ti-NCM cathode exhibits outstanding capacity retention,reaching 91.1%after 400 cycles at 1 C.This elaborate work contributes valuable insights into rational dual-modification engineering from a thermodynamic perspective for maximizing the electrochemical performances of NCM cathodes.

Understanding the correlation between energy-state mismatching and open-circuit voltage loss in bulk heterojunction solar cells

Photoinduced intermolecular charge transfer(PICT)determines the voltage loss in bulk heterojunction(BHJ)organic photovoltaics(OPVs),and this voltage loss can be minimized by inducing efficient PICT,which requires energy-state matching between the donor and acceptor at the BHJ interfaces.Thus,both geometrically and energetically accessible delocalized state matching at the hot energy level is crucial for achieving efficient PICT.In this study,an effective method for quantifying the hot state matching of OPVs was developed.The degree of energy-state matching between the electron donor and acceptor at BHJ interfaces was quantified using a mismatching factor(MF)calculated from the modified optical density of the BHJ.Furthermore,the correlation between the open-circuit voltage(Voc)of the OPV device and energy-state matching at the BHJ interface was investigated using the calculated MF.The OPVs with small absolute MF values exhibited high Voc values.This result clearly indicates that the energy-state matching between the donor and acceptor is crucial for achieving a high Voc in OPVs.Because the MF indicates the degree of energy-state matching,which is a critical factor for suppressing energy loss,it can be used to estimate the Voc loss in OPVs.

One-time application of controlled-release bulk blending fertilizer enhances yield,quality and photosynthetic efficiency in late japonica rice

Controlled-release urea(CRU)releases nitrogen(N)at the same pace that rice takes it up,which can effectively improve N use efficiency,increase rice yield and improve rice quality.However,few studies have described the effects of CRU application on the photosynthetic rate and endogenous enzyme activities of rice.Accordingly,a twoyear field trial was conducted with a total of seven treatments:CK,no N fertilizer;BBF,regular blended fertilizer;RBBF,20%N-reduced regular blended fertilizer;CRF1,70%CRU+30%regular urea one-time base application;CRF2,60%CRU+40%regular urea one-time base application;RCRF1,CRF1 treatment with 20%N reduction;and RCRF2,CRF2 treatment with 20%N reduction.Each treatment was conducted in triplicate.The results showed that the N recovery efficiency(NRE)of the controlled-release bulk blending fertilizer(CRBBF)treatments was significantly greater over the two years.There were significant yield increases of 4.1–5.9%under the CRF1treatment and 5.6–7.6%under the CRF2 treatment compared to the BBF treatment,but the differences between the reduced-N treatments RBBF and RCRF2 were not significant.Photosynthetic rates under the CRF1 and CRF2treatments were significantly higher than under the other treatments,and they had significantly greater RuBPCase,RuBisCO,glutamate synthase(GOGAT)and glutamine synthetase(GS)enzyme activities.Additionally,the soil NH_(4)^(+)-N and NO_(3)^(–)-N contents under the CRBBF treatments were significantly higher at the late growth stage of rice,which was more in-line with the fertilizer requirements of rice throughout the reproductive period.CRBBF also led to some improvement in rice quality.Compared with the BBF and RBBF treatments,the protein contents under the CRBBF treatments were reduced but the milling,appearance,eating and cooking qualities of the rice were improved.These results showed that the application of CRBBF can improve the NRE,photosynthetic rate and endogenous enzyme activities of rice,ensuring sufficient N nutrition and photosynthetic material production during rice growth and thereby achieving improved rice yield and quality.

Comparison of a Spectral Bin and Two Multi-Moment Bulk Microphysics Schemes for Supercell Simulation:Investigation into Key Processes Responsible for Hydrometeor Distributions and Precipitation

There are more uncertainties with ice hydrometeor representations and related processes than liquid hydrometeors within microphysics parameterization(MP)schemes because of their complicated geometries and physical properties.Idealized supercell simulations are produced using the WRF model coupled with“full”Hebrew University spectral bin MP(HU-SBM),and NSSL and Thompson bulk MP(BMP)schemes.HU-SBM downdrafts are typically weaker than those of the NSSL and Thompson simulations,accompanied by less rain evaporation.HU-SBM produces more cloud ice(plates),graupel,and hail than the BMPs,yet precipitates less at the surface.The limiting mass bins(and subsequently,particle size)of rimed ice in HU-SBM and slower rimed ice fall speeds lead to smaller melting-level net rimed ice fluxes than those of the BMPs.Aggregation from plates in HU-SBM,together with snow–graupel collisions,leads to a greater snow contribution to rain than those of the BMPs.Replacing HU-SBM’s fall speeds using the formulations of the BMPs after aggregating the discrete bin values to mass mixing ratios and total number concentrations increases net rain and rimed ice fluxes.Still,they are smaller in magnitude than bulk rain,NSSL hail,and Thompson graupel net fluxes near the surface.Conversely,the melting-layer net rimed ice fluxes are reduced when the fall speeds for the NSSL and Thompson simulations are calculated using HU-SBM fall speed formulations after discretizing the bulk particle size distributions(PSDs)into spectral bins.The results highlight precipitation sensitivity to storm dynamics,fall speed,hydrometeor evolution governed by process rates,and MP PSD design.

Bulked Segregant RNA-Seq Analysis of Pollinated Pistils Reveals Genes Influencing Spikelet Fertility in Rice

Prezygotic isolation is important for successful fertilization in rice, significantly affecting yield. This study focused on F_(5:6) generation plants derived from inter-subspecific crosses(Nipponbare × KDML105) with low(LS) and high seed-setting rates(HS), in which normal pollen fertility was observed. However, LS plants showed a reduced number of pollen grains adhering to the stigma and fewer pollen tubes reaching the ovules at 4-5 h post-pollination, compared with HS plants. Bulked segregant RNA-Seq analysis of pollinated pistils from the HS and LS groups revealed 249 and 473 differentially expressed genes(DEGs), respectively. Kyoto Encyclopedia of Genes and Genomes analysis of the HS and LS-specific DEGs indicated enrichment in metabolic pathways, pentose and glucuronate interconversions, and flavonoid biosynthesis. Several of these DEGs exhibited co-expression with pollen development genes and formed extensive clusters of co-expression networks. Compared with LS pistils, enzyme genes controlling pectin degradation, such as OsPME35 and OsPLL9, showed similar expression patterns, with higher levels in HS pistils pre-pollination. Os02g0467600, similar to cinnamate 4-hydroxylase gene(CYP73), involved in flavonoid biosynthesis, displayed higher expression in HS pistils post-pollination. Our findings suggest that OsPME35, OsPLL9, and Os02g0467600 contribute to prezygotic isolation by potentially modifying the stigma cell wall(OsPME35 and OsPLL9) and controlling later processes such as pollen-stigma adhesion(Os02g0467600) genes. Furthermore, several DEGs specific to HS and LS were co-localized with QTLs and functional genes associated with spikelet fertility. These findings provide valuable insights for further research on rice spikelet fertility, ultimately contributing to the development of high-yielding rice varieties.

内皮细胞特异性骨形态发生蛋白2对血管新生的影响:生物信息学分析和实验验证

背景:血管新生是心血管疾病的主要干预靶点,骨形态发生蛋白2具有调控血管新生作用,但内皮细胞特异性骨形态发生蛋白2对血管新生的调控作用不清楚。目的:探讨内皮细胞特异性骨形态发生蛋白2对血管新生的影响。方法:(1)生物信息学分析:通过Panglao DB公共基因表达数据库单细胞转录组荟萃分析观察骨形态发生蛋白2细胞群表达丰度和定位。血管新生小鼠和内皮(心内膜)过表达骨形态发生蛋白2小鼠转录组测序数据集探索内皮细胞骨形态发生蛋白2对血管新生信号通路的调控作用。(2)体内实验验证:建立小鼠后肢缺血模型,对比模型小鼠患侧与健侧缺血后肢7,14和21 d血流灌注情况,免疫荧光和免疫组织化学染色评估小鼠骨形态发生蛋白2和CD31的表达定位情况。(3)体外实验验证:体外培养人脐静脉内皮细胞,分为对照组、缺氧组和骨形态发生蛋白2抑制剂(Noggin蛋白)干预组,培养24 h,观察各组内皮细胞血管新生情况。结果与结论:(1)内皮细胞是表达骨形态发生蛋白2的重要细胞亚群,在血管新生内皮细胞和骨形态发生蛋白2过表达内皮细胞转录组再分析均发现骨形态发生蛋白2表达明显升高,血管新生通路明显激活。(2)缺血7 d小鼠新生血管周围骨形态发生蛋白2阳性血管明显增加(P<0.05),缺血2周骨形态发生蛋白2阳性血管明显减少(P<0.001)。(3)体外培养人脐静脉内皮细胞,缺氧干预后,内皮细胞迁移能力和血管出芽明显增加,血管新生因子血管内皮生长因子和血小板衍生生长因子的表达明显升高,Noggin明显减少了缺氧诱导的内皮细胞血管新生(P<0.001),并下调血管内皮生长因子和血小板衍生生长因子的表达(P<0.01)。(4)结果证实,内皮细胞特异性骨形态发生蛋白2具有调控血管新生作用,靶向性内皮细胞骨形态发生蛋白2可望改善血管新生。