Seismic Behavior of Frame with Specially Shaped Columns Subjected to Cyclic Load

In order to study the seismic behavior of frame with specially shaped columns,the hysteretic curve was analyzed based on a quasi-static test of a two-span,three-story frame with specially shaped columns.The top layer framework curve and the corresponding resilience model were obtained from the hysteretic curve.And the stiffness and strength degeneration were also investigated.The results indicated that the stiffness degeneration is not obvious,thus the frame with specially shaped columns has high earthquake-resistant behavior.The resilience model calculated from the test can provide reference for design and nonlinear finite element analysis.

Construction of a 3D Co(Ⅱ) Framework Based on Two Types of V-shaped Bidentate Ligands

A three-dimensional （3D） coordination polymer {[Co（bdc）（dpb）]·H2O}n （1） was prepared by solvothermal reaction of 1,3-dipyridyl benzene （dpb） with deprotonated 1,3-benzene- dicarboxylate （H2bdc）, and was characterized by elemental analysis, IR spectroscopy, and X-ray single-crystal diffraction. It crystallizes in the monoclinic system, space group C2/c with α = 15.478（6）, b = 12.865（5）, c = 24.091（10） ？, β = 95.599（5）°, V = 4774（3） ？3, C24H18CoN2O5, Mr = 473.34, Dc = 1.267 g/cm3, F（000） = 1864.0, μ = 0.748 mm-1 and Z = 8. Each Co（II） ion links three bdc2- anions to form an infinitely 1D ladder-shaped chain containing binuclear [（COO）Co]2 cluster, and dpb links adjacent 1D chains to form a 3D pcu framework. In addition, the UV-vis of 1 was also studied.

Frame property of unequal storey height with specially shaped columns under cyclic loading

A 1/3-scale reinfored concrete(RC) frame of unequal storey height with specially shaped columns was tested under low frequency cyclic loading.The damage characteristic,bearing capacity,deformation capacity and ductility were analyzed.The restoring force model of the frame was obtained based on the study of the hysteresis curve measured in experiment,and the stiffness degeneration characteristics of every storey of the frame were analyzed.Finally the accumulated damage was analyzed with the damage assessment model.It is shown that the seismic behavior of this frame of unequal storey height with specially shaped columns is generally good,but the bottom of first floor column is a weak part,which should be paid more attention in design,and the restoring force model derived from this experiment can be seen as a valuable guide for design and non-linear finite element analysis for this kind of structure.

The Optimal Cross-section Design of the “Trapezoid-V” Shaped Drainage Canal of Viscous Debris Flow

Debris flow drainage canal is one of the most widely used engineering measures to prevent and manage debris flow hazards.The shape and the sizes of the cross-section are important parameters when design debris flow drainage canal.Therefore,how to design the appropriate shape and sizes of the cross-section so that the drainage canal can have the optimal drainage capacity is very important and few researched at home and abroad.This study was conducted to analyze the hydraulic condition of a Trapezoid-V shaped drainage canal and optimize its cross-section.By assuming characteristic sizes of the cross-section,the paper deduced the configuration parameter of the cross-section of a Trapezoid-V shaped debris flow drainage canal.By theory analysis,it indicates that the optimal configuration parameter is only related to the side slope coefficient and the bottom transverse slope coefficient.For this study,the Heishui Gully,a first-order tributary of the lower Jinsha River,was used as an example to design the optimal cross-section of the drainage canal of debris flow.

The Richtmyer–Meshkov instability of a 'V' shaped air/helium interface subjected to a weak shock

The Richtmyer-Meshkov instability ofa ‘V＇ shaped air/helium gaseous interface subjected to a weak shock wave is experimentally studied. A soap film technique is adopted to create a ‘V＇ shaped interface with accurate initial conditions. Five kinds of ‘V＇ shaped interfaces with different vertex angles are formed to highlight the effects of initial conditions on the flow characteristics. The results show that a spike is generated after the shock impact, and grows constantly with time. As the vertex angle increases, vortices generated on the interface become less noticeable, and the spike develops less pronouncedly. The linear growth rate of interface width after compression phase is estimated by a linear model and a revised linear model, and the latter is proven to be more effective for the interface with high initial amplitudes. The linear growth rate of interface width is, for the first time in a heavy/light interface configuration, found to be a non-monotonous function of the initial perturbation amplitude-wavelength ratio.

RIGID-PLASTIC MECHANICAL MODEL FOR THE FORGING METHOD WITH HORIZONTAL V-SHAPED ANVIL

In order to decrease the anisotropy of mechanical properties, the rigid-plastic mechanical model for the forging method with horizontal V-shaped anvil is presented. The forging method, through the change of anvils shape, is able to control fibrous tissue direction, to improve the anisotropy of mechanical properties of axial forgings, to realize uniform forging. Therefore, the forging method can overcome the defect that conventional forging methods produce. The mechanism of the forging method with horizontal V-shaped anvil and the process of metal deformation are analyzed. The agreement of theoretical analysis with experimental study verifies the fact that the forging method with horizontal V-shaped anvil can control effectively the mechanical properties of axial forgings.

Scattering of SH waves induced by a symmetrical V-shaped canyon: a unified analytical solution

This paper reports a series solution of wave functions for two-dimensional scattering and diffraction of plane SH waves induced by a symmetrical V-shaped canyon with different shape ratios. A half-space with a symmetrical V-shaped canyon is divided into two sub-regions by using a circular-arc auxiliary boundary. The two sub-regions are represented by global and local cylindrical coordinate systems, respectively. In each coordinate system, the wave field satisfying the Helmholtz equation is represented by the separation of variables method, in terms of the series of both Bessel functions and Hankel functions with unknown complex coefficients. Then, the two wave fields are described in the local coordinate system using the Graf addition theorem. Finally, the unknown coefficients are sought by satisfying the continuity conditions of the auxiliary boundary. To consider the phase characteristics of the wave scattering, a parametric analysis is carried out in the time domain by assuming an incident signal of the Ricker type. Surface and subsurface transient responses demonstrate the characteristics and mechanisms of wave propagating and scattering.

Light-extraction efficiency and forward voltage in GaN-based light-emitting diodes with different patterns of V-shaped pits

We present a new method of making a textured V-pit surface for improving the light extraction efficiency in GaN- based light-emitting diodes and compare it with the usual low-temperature method for p-GaN V-pits. Three types of GaNbased light-emitting diodes （LEDs） with surface V-pits in different densities and regions were grown by metal-organic chemical vapor deposition. We achieved the highest output power and lowest forward voltage values with the p-InGaN V-pit LED. The V-pits enhanced the light output power values by 1.45 times the values of the conventional LED owing to an enhancement of the light scattering probability and an effective reduction of Mg-acceptor activation energy. Moreover, this new technique effectively solved the higher forward voltage problem of the usual V-pit LED.

Electronic and transport properties of V-shaped defect zigzag MoS_2 nanoribbons

Based on the nonequilibrium Green＇s function （NEGF） in combination with density functional theory （DFT） calcu- lations, we study the electronic structures and transport properties of zigzag MoS2 nanoribbons （ZMNRs） with V-shaped vacancy defects on the edge. The vacancy formation energy results show that the zigzag vacancy is easier to create on the edge of ZMNR than the armchair vacancy. Both of the defects can make the electronic band structures of ZMNRs change from metal to semiconductor. The calculations of electronic transport properties depict that the currents drop off clearly and rectification ratios increase in the defected systems. These effects would open up possibilities for their applications in novel nanoelectronic devices.

Wave Pressure Acting on V-Shaped Floating Breakwater in Random Seas

Wave pressure on the wet surface of a V-shaped floating breakwater in random seas is investigated. Considering the diffraction effect, the unit velocity potential caused by the single regular waves around the breakwater is solved using the finite-depth Green function and boundary element method, in which the Green function is solved by integral method. The Response-Amplitude Operator(RAO) of wave pressure is acquired according to the Longuet-Higgins' wave model and the linear Bernoulli equation. Furthermore, the wave pressure's response spectrum is calculated according to the wave spectrum by discretizing the frequency domain. The wave pressure's characteristic value corresponding to certain cumulative probability is determined according to the Rayleigh distribution of wave heights. The numerical results and field test results are compared, which indicates that the wave pressure calculated in random seas agrees with that of field measurements. It is found that the bigger angle between legs will cause the bigger pressure response, while the increase in leg length does not influence the pressure significantly. The pressure at the side of head sea is larger than that of back waves. When the incident wave angle changes from 0? to 90?, the pressure at the side of back waves decreases clearly, while at the side of head sea, the situation is more complicated and there seems no obvious tendency. The concentration of wave energy around low frequency(long wavelength) will induce bigger wave pressure, and more attention should be paid to this situation for the structure safety.

Construction of a 2D Cd(II) Coordination Polymer Based on a V-shaped Bidentate Ligand

A two-dimensional（2D）coordination polymer{[Cd（bdc）（dpb）]·H2O}n（1）has been prepared by solvothermal reaction of 1,3-dipyridyl benzene（1,3-dpb）with deprotonated1,4-benzenedicarboxylate（H2bdc）,and was characterized by elemental analysis,IR spectroscopy,and X-ray single-crystal diffraction.It crystallizes in the monoclinic system,space group C2/c with a=15.1839（12）,b=20.7585（17）,c=7.2989（6）,β=117.3450（10）°,V=2043.5（3）3,C24H18N2O5Cd,Mr=526.81,Dc=1.712 g/cm3,F（000）=1056.0,μ=1.110 mm-1and Z=4.The neighboring Cd（II）ions link the bdc2-anions and 1,3-dpb to form an infinite 2D sheet,and such two2D sheets are interlocked with each other to form a 2D→2D sheet.Two groups of interlocked sheets are further linked together by intermolecularπ···πinteraction,giving a 3D supramolecular network.In addition,the fluorescence property of 1 was also studied.

Extrusion process of 304L H-shaped stainless steel used in passive residual heat removal heat exchanger

304L H-shaped stainless steel is used as the support frame of the passive residual heat removal heat exchanger(PRHR HX) in a nuclear fission reactor. The extrusion process is adopted to manufacture the 304L H-shaped stainless steel. Finite element method simulation is herein used to analyze metal flow characteristics, optimize the extrusion die, and predict the extrusion force at different temperatures and speeds. A Φ400-mm container and Φ388-mm forging billet are selected, and the 304L H-shaped stainless steel is successfully manufactured using a Germany SMS 60 MN horizontal extruder. The mechanical properties and microstructure of the manufactured 304L H-shaped stainless steel meet the requirements of the PRHR HX, and the surfaces of the product pass the dye penetration test. The H-shaped stainless steels are used in Haiyang nuclear power plant in Shandong Province.

Carrier transport via V-shaped pits in InGaN/GaN MQW solar cells

Carrier transport via the V-shaped pits （V-pits） in InGaN/GaN multiple-quantum-well （MQW） solar cells is numer- ically investigated. By simulations, it is found that the V-pits can act as effective escape paths for the photo-generated carriers. Due to the thin barrier thickness and low indium composition of the MQW on V-pit sidewall, the carriers entered the sidewall QWs can easily escape and contribute to the photocurrent. This forms a parallel escape route for the carries generated in the fiat quantum wells. As the barrier thickness of the fiat MQW increases, more carriers would transport via the V-pits. Furthermore, it is found that the V-pits may reduce the recombination losses of carriers due to their screening effect to the dislocations. These discoveries are not only helpful for understanding the carrier transport mechanism in the InGaN/GaN MQW, but also important in design of the structure of solar cells.

Enhanced optical transmission by V-shaped nanoslit in metal film

In this paper, we reveal that the enhanced transmission through a perforated metal film can be further boosted up by a V-shaped nanoslit, which consists of two connected oblique slits. The maximum transmission at resonance can be enhanced significantly by 71.5% in comparison with the corresponding vertical slit with the same exit width. The value and position of transmission resonance peak strongly depend on the apex angle of the V-shaped slit. The optimum apex angle, at which the transmission is maximal, is sensitive to the slit width. Such phenomena can be well explained by a concrete picture in which the incident wave drives free electrons on the slit walls. Moreover, we also simply analyze the splitting of the transmission peak in the symmetry broken V-shaped slit, originating from the resonances of different parts of the V-shaped slit. We expect that our findings will be used to design the nanoscale light sources based on the metal nanoslit structures.

Experimental Study on Seismic Behavior of Exterior Joints of Special-shaped Columns with Different Lengths of Limbs

Four exterior joints with special-shaped columns which have different lengths of limbs are tested under low cyclic loading. Speeial-shaped columns adopted are L- and T-shaped in section. It can be concluded that crack pattern, failure mode and shear strength of joints are affected by the length of limb, and that shear strength and ductility increase with the length of limb; the joints with the flexural failure of the beam have better seismic behavior than those with the shear failure of the joint core.

Study on a W-band modified V-shaped microstrip meander-line traveling-wave tube

The study on a miniaturized, low-voltage, wide-bandwidth, high-efficiency modified V-shaped microstrip meander-line slow-wave structure is presented. This structure is evolved from the original U-shaped microstrip meander-line slow-wave structure, combining the advantages of a traditional microstrip and a rectangular helix. In this paper, simulations of the electromagnetic characteristics and the beam-wave interaction of this structure are carried out. Our study shows that when the design voltage and the current of a sheet electron beam are set to be 4700 V and 100 mA, respectively, this miniature millimeter-wave power amplifier is capable of delivering 160-W output power with a corresponding gain of 37.3 dB and a maximum interaction efficiency of 34% at 97 GHz.

Investigating Jet Appearance in Different Background Lights with High-Speed Frame Photography

Shaped charge jet formation process is studied under the conditions of different background lights by means of high speed frame photography. In order to shoot true jet appearance, the glass tube in which jet moves is vacuumized. The experiment results show that observing jet appearance with the double reflecting mirrors system is feasible as long as the vacuum of the glass tube can meet the requirement of experiment.

低肋与V形肋复合结构在双通道中的强化换热数值研究

随着燃气轮机内涡轮入口温度的升高,燃气轮机会出现热障问题,为保证燃气轮机安全运行,复合结构能够有效提高通道的冷却性能来解决此问题。采用SST k-ω湍流模型对带有低肋与V肋复合结构双通道的流动与传热特性进行了数值模拟,将圆形肋复合结构、扇叶形肋复合结构和葫芦形肋复合结构与纯V形肋在雷诺数为10 000~60 000时的传热性能进行比较,探索出综合换热效果最佳的复合结构。发现相比于纯V形肋通道,复合结构双通道的综合传热性能均得到提升,其中葫芦形肋与V形肋组成的复合结构的综合换热效果最好。葫芦肋复合结构的Nu相比于纯V形肋提高了4.33%~6.6%,f提高了0.04%~4.48%,η最佳值达到了2.13。葫芦形肋复合结构的η比45°斜方形肋和45°斜花形肋分别增大了25.51%~32.98%和4.73%~10.51%,同时,低肋与V形肋组成的复合结构综合换热性能要优于凹坑与V形肋组成的复合结构。葫芦肋复合结构有效增强通道的换热效果且压力损失增长较小,可显著提升涡轮内部冷却通道的综合换热性能。

V型折叠颏下皮瓣修复口腔缺损的临床应用

目的:口腔中小型缺损修复一直是一个难题,游离皮瓣和远位带蒂组织瓣难以满足临床需求,传统颏下皮瓣存在供区损伤风险。本研究旨在探讨V型折叠颏下皮瓣修复口腔中小型缺损的疗效。方法:回顾性分析2019年3月至2022年12月中南大学湘雅三医院口腔科收治的28例口腔黏膜病变患者的临床资料。根据颏下皮瓣手术方式的不同将患者分为V型折叠组(17例)和传统组(11例),V型折叠组采用V型折叠颏下皮瓣进行术后软组织修复,传统组采用传统颏下皮瓣进行修复,患者术后随访6~48个月。比较2组皮瓣存活情况、皮瓣修复时间以及皮瓣修复效果。结果:2组皮瓣存活率、皮瓣大小、制瓣时间、修复手术时间和术后住院时间差异均无统计学意义(均P>0.05)。术后6个月,V型折叠组无抬头困难和下唇外翻,无皮肤“猫耳”畸形,疤痕隐藏于下颌骨下缘处,创面美观度、功能评分均明显高于传统组(均P<0.05)。结论:V型折叠颏下皮瓣具有设计灵活、制备简单、血供可靠、保护供区等优点,可以有效维持颏部美观和避免功能障碍。