Lateral earth pressure of granular backfills on retaining walls with expanded polystyrene geofoam inclusions under limited surcharge loading

Existing studies have focused on the behavior of the retaining wall equipped with expanded polystyrene(EPS)geofoam inclusions under semi-infinite surcharge loading rather than limited surcharge loading.In this paper,the failure mode and the earth pressure acting on the rigid retaining wall with EPS geofoam inclusions and granular backfills(henceforth referred to as EPS-wall),under limited surcharge loading are investigated through two-and three-dimensional model tests.The testing results show that different from the sliding of almost all the backfill in the EPS-wall under semi-infinite surcharge loading,only an approximately triangular backfill slides in the wall under limited surcharge loading.The distribution of the lateral earth pressure on the EPS-wall under limited surcharge loading is non-linear,and the distribution changes from the increase of the wall depth to the decrease with the increase of the limited surcharge loading.An approach based on the force equilibrium of a differential element is developed to predict the lateral earth pressure behind the EPS-wall subjected to limited surcharge loading,and its performance was fully validated by the three-dimensional model tests.

Compression properties of cost-efficient porous expanded clay reinforced AA7075 syntactic foams fabricated by industrial-oriented die casting technology

In today’s manufacturing industries,hard competition between rival firms makes it compulsory for researchers to design lighter and cheaper machine components due to the megatrends of cost-effectiveness and anti-pollution.At this point,aluminum syntactic foams(ASFs)are new-generation engineering composites and come into the upfront as a problem-solver.Owing to their features like low density,sufficient elongation,and perfect energy absorption ability,these advanced foams have been considerably seductive for many industrial sectors nowadays.In this study,an industrial-oriented automatic die casting technology was used for the first time to manufacture the combination of AA7075/porous expanded clay(PEC).Micro evaluations(optical and FESEM)reveal that there is a homogenous particle distribution in the foam samples,and inspections are compatible with the other ASF studies.Additionally,T6 aging heat treatment was operated on one half of the produced foams to explore the probable impact of aging on the compressive responses.Attained results show that PEC particles can be an alternative to expensive hollow spheres used in the previous works.Besides,a favorable relationship is ascertained between the aging treatment and mechanical properties such as compression strength and plateau strength.

Experimental study on thermal and mechanical properties of tailings-based cemented paste backfill with CaCl_(2)·6H_(2)O/expanded vermiculite shape stabilized phase change materials

CaCl_(2)·6H_(2)O/expanded vermiculite shape stabilized phase change materials(CEV)was prepared by atmospheric impregnation method.Using gold mine tailings as aggregate of cemented paste backfill(CPB)material,the CPB with CEV added was prepared,and the specific heat capacity,thermal conductivity,and uniaxial compressive strength(UCS)of CPB with different cement-tailing ratios and CEV addition ratios were tested,the influence of the above variables on the thermal and mechanical properties of CPB was analyzed.The results show that the maximum encapsulation capacity of expanded vermiculite for CaCl_(2)·6H_(2)O is about 60%,and the melting and solidification enthalpies of CEV can reach 98.87 J/g and 97.56 J/g,respectively.For the CPB without CEV,the specific heat capacity,thermal conductivity,and UCS decrease with the decrease of cement-tailing ratio.For the CPB with CEV added,with the increase of CEV addition ratio,the specific heat capacity increases significantly,and the sensible heat storage capacity and latent heat storage capacity can be increased by at least 10.74%and 218.97%respectively after adding 12%CEV.However,the addition of CEV leads to the increase of pores,and the thermal conductivity and UCS both decrease with the increase of CEV addition.When cement-tailing ratio is 1:8 and 6%,9%,and 12%of CEV are added,the 28-days UCS of CPB is less than 1 MPa.Considering the heat storage capacity and cost price of backfill,the recommended proportion scheme of CPB material presents cement-tailing ratio of 1:6 and 12%CEV,and the most recommended heat storage/release temperature cycle range of CPB with added CEV is from 20 to 40℃.This work can provide theoretical basis for the utilization of heat storage backfill in green mines.

基于CTA颅内动脉瘤形态联合PHASES评分对破裂出血预测研究

目的:分析头颈部计算机断层扫描血管成像(CTA)联合PHASES评分对颅内动脉瘤(IA)破裂出血的预测价值。方法:回顾性分析2021年10月—2023年9月东莞市长安医院诊治的IA患者临床资料,根据IA破裂出血与否分为IA破裂组(n=46)和IA未破裂组(n=44),收集两组临床资料,对比两组患者CTA影像瘤体特征参数和PHASES评分结果。采用受试者工作特征(ROC)曲线分析两者联合预测动脉瘤破裂的效能。结果:IA破裂组高血压、糖尿病发生率及PHASES评分均高于IA未破裂组,差异有统计学意义(P <0.05)。两组病灶位置以颈内动脉(ICA)和大脑中动脉(MCA)为主,但IA破裂组病灶位置在MCA的占比为41.30%,高于IA未破裂组的20.45%,瘤体>7 mm的最多(瘤体7~9.9 mm占65.22%),瘤体形态不规则占58.7%,未破裂组病灶位置在ICA最多(68.18%),瘤体<7 mm的居多(75.00%),瘤体形态规则囊状动脉瘤占93.18%,差异有统计学意义(P <0.05)。CTA瘤体特征参数比较,IA破裂组患者瘤颈宽度、瘤体高度、瘤体长度、动脉瘤最大直径、入射夹角、动脉瘤体颈比等参数均高于IA未破裂组,差异有统计学意义(P <0.05)。CTA瘤体特征参数+PHASES评分联合预测曲线下面积为0.916,高于CTA瘤体特征参数(0.901)和PHASES评分(0.731)。结论:CTA瘤体特征参数+PHASES评分联合预测IA患者破裂出血效能最佳。

K_(x)C_(y) phase induced expanded interlayer in ultra-thin carbon toward full potassium-ion capacitors

Carbonaceous materials have been regarded as highly promising anode candidates for potassium storage with their cost-effectiveness and environmental benignity.However,low specific capacity and difficulty in large-scale synthesis largely hinder their further development.Herein,a thermal-induced potassium–carbon alloy phase(K_(x)C_(y))with the expanded interlayer spacing strategy is first put forward.Through in situ high-temperature X-ray diffraction,a K_(2)C_(2) phase is evoked by thermal energy during the in-situ carbonization process of carbon quantum dots intermediate derived from potassium-containing precursors,whereas no lithium or sodium–carbon alloy phase is observed from lithium/sodium-containing precursors.The asobtained ultra-thin carbon nanosheets achieve adjustable layer spacing,preparation in bulk,delivering reversible potassium storage of 403.4 mAh g^(−1) at 100 mA g^(−1) and 161.2 mAh g^(−1) even at 5.0 A g^(−1),which is one of the most impressive K-storage performances reported so far with great potential application.Furthermore,the assembled potassium-ion hybrid capacitor by combining the impressive CFMs-900 anode with the three-dimensional framework-activated carbon delivers a high energy-power density of 251.7 Wh kg^(−1) at 250Wkg^(−1) with long-term stability.This study opens a scalable avenue to realize the expanded interlayer spacing,which can be extended to other multicarboxyl potassium salts and can provide approach for the design of high-performance carbon anode materials for potassium storage.

Effects of internals on phase holdup and backmixing in a slightly-expanded-bed reactor with gas–liquid concurrent upflow

Five different internals were designed,and their effects on phase holdup and backmixing were investigated in a gas–liquid concurrent upflow reactor where the spherical alumina packing particles of three diameters(3.0,4.5 and6.0 mm)were slightly expanded under the conditions of varied superficial gas velocities(6.77×10-2-3.61×10-1 m·s-1)and superficial liquid velocities(9.47×10-4-2.17×10-3 m·s-1).The experimental results show that the gas holdup increases with the superficial gas velocity and particle size,opposite to the variational trend of liquid holdup.When an internal component is installed amid the upflow reactor,a higher gas holdup,a less liquid holdup and a larger Peclet number characterizing the weaker backmixing are obtained compared to those in the bed without internals under the same operating conditions.Additionally,the minimal backmixing is observed in the reactor equipped with the internals with a novel multi-step design.Finally,empirical correlations were proposed for estimating gas holdup,liquid holdup and Peclet number with the relative deviations within 11%,12%and 25%,respectively.

Phase-engineering modulation of Mn-based oxide cathode for constructing super-stable sodium storage

The Mn-based oxide cathode with enriched crystal phase structure and component diversity can provide the excellent chemistry structure for Na-ion batteries.Nevertheless,the broad application prospect is obstructed by the sluggish Na^(+)kinetics and the phase transitions upon cycling.Herein,we establish the thermodynamically stable phase diagram of various Mn-based oxide composites precisely controlled by sodium content tailoring strategy coupling with co-doping and solid-state reaction.The chemical environment of the P2/P'3 and P2/P3 biphasic composites indicate that the charge compensation mechanism stems from the cooperative contribution of anions and cations.Benefiting from the no phase transition to scavenge the structure strain,P2/P'3 electrode can deliver long cycling stability(capacity retention of 73.8%after 1000 cycles at 10 C)and outstanding rate properties(the discharge capacity of 84.08 mA h g^(-1)at 20 C)than P2/P3 electrode.Furthermore,the DFT calculation demonstrates that the introducing novel P'3 phase can significantly regulate the Na^(+)reaction dynamics and modify the local electron configuration of Mn.The effective phase engineering can provide a reference for designing other high-performance electrode materials for Na-ion batteries.

Study on Sustained-Release Pesticides Blended with Fosthiazate-Stearic Acid/Expanded Perlite

The low utilization rate of pesticides makes the migration of pesticides in water and soil,which brings great harm to the ecosystem.The development of pesticide carriers with good drug loading capacity and release control abil-ity is an effective method to realize effective utilization of pesticides and reduce pesticide losses.In this work,fosthiazate-stearic acid/expanded perlite sustained-release particles were successfully prepared by vacuum impregnation using expanded perlite(EP)as carrier,fosthiazate(FOS)as model pesticide and stearic acid(SA)as hydrophobic matrix.The structure and morphology of the samples were studied by BET,FT-IR,TGA,XRD,DSC and SEM.The effects of different mass ratios of FOS to SA on loading capacity and release rate at 24 h were investigated.The sustained release behavior of FOS-SA/EP at different temperatures and pH values was investigated by static dialysis bag method.The results showed that FOS and SA were adsorbed in EP pores by physical interaction.With the mass ratios of FOS to SA decreasing from 7:3 to 3:7,the 24 h release rate of FOS-SA/EP decreased from 18.77%to 8.05%,and the drug loading decreased from 461.32 to 130.99 mg/g.FOS-SA/EP showed obvious temperature response at 25℃,30℃ and 35℃,the cumulative release rate(CRR)of 200 h were 33.38%,41.50%and 51.17%,respectively.When pH=5,the CRR of FOS was higher than that of pH=7,and the CRR of FOS for 200 h were 49.01%and 30.12%,respectively.At different temperatures and pH=5,the release mechanism of FOS-SA/EP belongs to the Fickian diffusion mechanism;When pH=7,the diffusion mechanism is dominant,and the dissolution mechanism is complementary.

Shikimic acid accelerates phase change and flowering in Chinese jujube

The juvenile-to-adult phase change with first flowering as the indicator plays a crucial role in the lifecycle of fruit trees. However, the molecular mechanisms underlying phase change in fruit trees remain largely unknown. Shikimic acid (ShA) pathway is a main metabolic pathway closely related to the synthesis of hormones and many important secondary metabolites participating in plant phase change. So,whether ShA regulates phase change in plants is worth clarifying. Here, the distinct morphological characteristics and the underlying mechanisms of phase change in jujube (Ziziphus jujuba Mill.), an important fruit tree native to China with nutritious fruit and outstanding tolerance abiotic stresses, were clarified. A combined transcriptome and metabolome analysis found that ShA is positively involved in jujube(Yuhong’×Xing 16’) phase change. The genes in the upstream of ShA synthesis pathway (ZjDAHPS, ZjDHQS and ZjSDH), the contents of ShA and the downstream secondary metabolites like phenols were significantly upregulated in the phase change period. Further, the treatment of spraying exogenous ShA verified that ShA at a very low concentration (60 mg·L^(-1)) can substantially speed up the phase change and flowering of jujube and other tested plants including Arabidopsis, tomato and wheat. The exogenous ShA (60 mg·L^(-1)) treatment in jujube seedlings could increase the accumulation of endogenous ShA, enhance leaf photosynthesis and the synthesis of phenols especially flavonoids and phenolic acids, and promote the expression of genes (ZjCOs, ZjNFYs and ZjPHYs) involved in flowering pathway. Basing on above results, we put forward a propose for the underlying mechanism of ShA regulating phase change, and a hypothesis that ShA could be considered a phytohormone-like substance because it is endogenous, ubiquitous, movable and highly efficient at very low concentrations. This study highlights the critical role of ShA in plant phase change and its phytohormone-like properties.

Experimental study on lightweight expanded clay at particle level:Breakage of isolated grains

In this study,more than 1500 particles of lightweight expanded clay aggregate(LECA)are individually loaded up to breakage,following different patterns of contact(from 2 to 7)using a purpose-built apparatus.Consequently,a statistical model for predicting the number of fragments into which a grain breaks as a function of the number of contacts and their diameter is proposed.The number of fragments is found to follow a statistical binomial-type distribution function that depends on the number of contacts.In addition,a model based on Bayesian networks,capable of assessing the number of fragments and their size(measured as normalized weight)as a function of the number of contacts,is implemented.The proposed method is applicable when performing discrete element method(DEM)simulations on granular media in which grain breakage plays a relevant role.

Microstructure and damping properties of LPSO phase dominant Mg-Ni-Y and Mg-Zn-Ni-Y alloys

This work studied the microstructure,mechanical properties and damping properties of Mg_(95.34)Ni_(2)Y_(2.66) and Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloys systematically.The difference in the evolution of the long-period stacked ordered(LPSO)phase in the two alloys during heat treatment was the focus.The morphology of the as-cast Mg_(95.34)Ni_(2)Y_(2.66)presented a disordered network.After heat treatment at 773 K for 2 hours,the eutectic phase was integrated into the matrix,and the LPSO phase maintained the 18R structure.As Zn partially replaced Ni,the crystal grains became rounded in the cast alloy,and lamellar LPSO phases and more solid solution atoms were contained in the matrix after heat treatment of the Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloy.Both Zn and the heat treatment had a significant effect on damping.Obvious dislocation internal friction peaks and grain boundary internal friction peaks were found after temperature-dependent damping of the Mg_(95.34)Ni_(2)Y_(2.66)and Mg_(95.34)Zn_(1)Ni_(1)Y_(2.66)alloys.After heat treatment,the dislocation peak was significantly increased,especially in the alloy Mg_(95.34)Ni_(2)Y_(2).66.The annealed Mg_(95.34)Ni_(2)Y_(2.66)alloy with a rod-shaped LPSO phase exhibited a good damping performance of 0.14 atε=10^(−3),which was due to the difference between the second phase and solid solution atom content.These factors also affected the dynamic modulus of the alloy.The results of this study will help in further development of high-damping magnesium alloys.

Dense Pellicular Agarose-Glass Beads for Expanded Bed Application: Flow Hydrodynamics and Solid Phase Classifications

Two dense pellicular agarose-glass matrices of different sizes and densities, i.e., AG-S and AG-L, have been characterized for their bed expansion behavior, flow hydrodynamics and particle classifications in an expanded bed system. A 26 mm ID column with side ports was used for sampling the liquid-solid suspension during expanded bed operations. Measurements of the collected solid phase at different column positions yielded the particle size and density distribution data. It was found that the composite matrices showed particle size as well as density classifications along the column axis, i.e., both the size and density of each matrix decreased with increasing the axial bed height. Their axial classifications were expressed by a correlation related to both the particle size and density as a function of the dimensionless axial bed height. The correlation was found to fairly describe the solid phase classifications in the expanded bed system. Moreover, it can also be applied to other two commercial solid matrices designed for expanded bed applications.

ZnO-Embedded Expanded Graphite Composite Anodes with Controlled Charge Storage Mechanism Enabling Operation of Lithium-Ion Batteries at Ultra-Low Temperatures

As lithium(Li)-ion batteries expand their applications,operating over a wide temperature range becomes increasingly important.However,the lowtemperature performance of conventional graphite anodes is severely hampered by the poor diffusion kinetics of Li ions(Li^(+)).Here,zinc oxide(ZnO) nanoparticles are incorporated into the expanded graphite to improve Li^(+)diffusion kinetics,resulting in a significant improvement in lowtemperature performance.The ZnO-embedded expanded graphite anodes are investigated with different amounts of ZnO to establish the structurecharge storage mechanism-performance relationship with a focus on lowtemperature applications.Electrochemical analysis reveals that the ZnOembedded expanded graphite anode with nano-sized ZnO maintains a large portion of the diffusion-controlled charge storage mechanism at an ultra-low temperature of-50℃ Due to this significantly enhanced Li^(+)diffusion rate,a full cell with the ZnO-embedded expanded graphite anode and a LiNi_(0.88)Co_(0.09)Al_(0.03)O_(2)cathode delivers high capacities of 176 mAh g^(-1)at20℃ and 86 mAh g^(-1)at-50℃ at a high rate of 1 C.The outstanding low-temperature performance of the composite anode by improving the Li^(+)diffusion kinetics provides important scientific insights into the fundamental design principles of anodes for low-temperature Li-ion battery operation.

Heat transfer enhanced inorganic phase change material compositing carbon nanotubes for battery thermal management and thermal runaway propagation mitigation

Developing technologies that can be applied simultaneously in battery thermal management(BTM)and thermal runaway(TR)mitigation is significant to improving the safety of lithium-ion battery systems.Inorganic phase change material(PCM)with nonflammability has the potential to achieve this dual function.This study proposed an encapsulated inorganic phase change material(EPCM)with a heat transfer enhancement for battery systems,where Na_(2)HPO_(4)·12H_(2)O was used as the core PCM encapsulated by silica and the additive of carbon nanotube(CNT)was applied to enhance the thermal conductivity.The microstructure and thermal properties of the EPCM/CNT were analyzed by a series of characterization tests.Two different incorporating methods of CNT were compared and the proper CNT adding amount was also studied.After preparation,the battery thermal management performance and TR propagation mitigation effects of EPCM/CNT were further investigated on the battery modules.The experimental results of thermal management tests showed that EPCM/CNT not only slowed down the temperature rising of the module but also improved the temperature uniformity during normal operation.The peak battery temperature decreased from 76℃to 61.2℃at 2 C discharge rate and the temperature difference was controlled below 3℃.Moreover,the results of TR propagation tests demonstrated that nonflammable EPCM/CNT with good heat absorption could work as a TR barrier,which exhibited effective mitigation on TR and TR propagation.The trigger time of three cells was successfully delayed by 129,474 and 551 s,respectively and the propagation intervals were greatly extended as well.

Preparation and Properties of 1-octadecanol/1,3:2,4-di-(3,4-dimethyl) Benzylidene Sorbitol/Expanded Graphite Form-stable Composite Phase Change Material

A 1 -octadecanol (OD)/1,3:2,4-di-(3,4-dimethyl) benzylidene sorbitol (DMDBS)/expander graphite (EG) composite was prepared as a form-stable phase change material (PCM) by vacuum melting method. The results of field emission-scanning electron microscopy (FE-SEM) showed that 1 -octadecanol was restricted in the three-dimensional network formed by DMDBS and the honeycomb network formed by EG. X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) results showed that no chemical reaction occurred among the components of composite PCM in the preparation process. The gel-to-sol transition temperature of the composite PCMs containing DMDBS was much higher than the melting point of pure 1-octadecanol. The improvements in preventing leakage and thermal stability limits were mainly attributed to the synergistic effect of the three-dimensional network formed by DMDBS and the honeycomb network formed by EG. Differential scanning calorimeter (DSC) was used to determine the latent heat and phase change temperature of the composite PCMs. During melting and freezing process the latent heat values of the PCM with the composition of 91% OD/3% DMDBS/6% EG were 214.9 and 185.9 kJ kg'1, respectively. Its degree of supercooling was only 0.1 °C. Thermal constant analyzer results showed that its thermal conductivity (k) changed up to roughly 10 times over that of OD/DMDBS matrix.

In situ observation of the phase transformation kinetics of bismuth during shock release

A time-resolved x-ray diffraction technique is employed to monitor the structural transformation of laser-shocked bismuth.Results reveal a retarded transformation from the shock-induced Bi-Ⅴphase to a metastable Bi-Ⅳphase during the shock release,instead of the thermodynamically stable Bi-Ⅲphase.The emergence of the metastable Bi-Ⅳphase is understood by the competitive interplay between two transformation pathways towards the Bi-Ⅳand Bi-Ⅲ,respectively.The former is more rapid than the latter because the Bi-Ⅴto B-Ⅳtransformation is driven by interaction between the closest atoms while the Bi-Ⅴto B-Ⅲtransformation requires interaction between the second-closest atoms.The nucleation time for the Bi-Ⅴto Bi-Ⅳtransformation is determined to be 5.1±0.9 ns according to a classical nucleation model.This observation demonstrates the importance of the formation of the transient metastable phases,which can change the phase transformation pathway in a dynamic process.

Nursing Care and Causative Analysis of Grade IV Capsular Contracture Following Breast Cancer Expander Implantation

Objective: By observing the treatment and nursing care of a patient with Grade IV capsular contracture following breast cancer expander implantation and subsequent Stage II reconstruction, we aim to analyze the reasons for the formation of capsular contracture after Stage I expander implantation and prevent its recurrence following Stage II reconstruction. Methods: In May 2020, the patient noticed an increase in the size of a breast mass. In August, she underwent AC-THP neoadjuvant chemotherapy, followed by a “right breast-conserving nipple-areolar subglandular excision + right axillary lymph node dissection + expander implantation” surgery in November 2020. Radiation therapy began in January 2021. During radiation therapy, the patient experienced severe breast hardening, distortion, tenderness, and was diagnosed with Grade IV capsular contracture. To relieve the capsular contracture, the patient underwent a “contracted capsule incision and release procedure + removal of the right breast expander + right breast implantation” surgery in July 2021. Postoperatively, measures were taken to prevent incision infection, emphasizing aseptic techniques, ensuring smooth negative pressure drainage, reducing skin flap tension, monitoring skin flap blood supply, actively preventing subcutaneous effusion and hematoma, and applying appropriate compression dressings. Results: The patient was discharged after the removal of the drainage tube. During the postoperative follow-up at 3 and 6 months, there was no recurrence of capsular contracture, and the breast appeared full, upright, and relatively soft. There were no complications such as hematoma, infection, breast implant rupture, breast sagging, or displacement. The patient had a good outcome without additional financial or surgical burdens. Conclusion: The occurrence of Grade IV capsular contracture in the patient is generally related to infection after Stage I expander implantation, improper compression dressing, excessive saline injection causing content infiltration, and radiation therapy. Therefore, it is recommended to enhance the intraoperative and postoperative prophylactic use of antibiotics after Stage I expander implantation. Intermittent saline injection after surgery, with the amount of saline gradually increasing rather than filling all at once, is advisable. This helps the breast tissue gradually adapt to expansion, reducing the risk of capsular contracture. Postoperatively, patients should be instructed to wear pressure garments and breast elastic bandages while intensifying breast monitoring during radiation therapy and increasing postoperative follow-up.

The First Five Years of a Phase Theory for Complex Systems and Networks

In this paper,we review the development of a phase theory for systems and networks in its first five years,represented by a trilogy:Matrix phases and their properties;The MIMO LTI system phase response,its physical interpretations,the small phase theorem,and the sectored real lemma;The synchronization of a multi-agent network using phase alignment.Towards the end,we also summarize a list of ongoing research on the phase theory and speculate what will happen in the next five years.

Structure of Periodic Flows through a Channel with a Suddenly Expanded and Contracted Part

With respect to flows in a two-dimensional sudden expansion and contraction channel having a pair of cavities, numerical simulation was performed by imposing inlet/outlet boundary conditions giving a velocity distribution to the inlet. Periodic flows have been reproduced, which have a discrete spectrum about frequency. A fundamental wave occupies most part of the disturbance components, but higher harmonic waves are also included. The disturbance is excited by Kelvin-Helmholtz instability in a cavity section, where only the fundamental wave is generated. A wavenumber is regulated by a channel length under a periodic boundary condition, but there is no restriction in a main flow direction under the inlet/outlet boundary conditions, and therefore, some wavenumbers can occur. Therefore, an arbitrary frequency component of disturbance is a synthesized wave composed of various wave numbers. There are two kinds of components constituting this synthesized wave: a maximum of a velocity distribution is near a wall and in the center of the channel, which are called as wall mode and central mode in linear stability analysis of the plane Poiseuille flow. The synthesized wave composed of some modes shows a tendency to lower wavenumbers at the center of the channel.

Influence of Omega 3 Fatty Acid Supplementation on Phase Angle Values of People Living with HIV/AIDS with Lipodystrophy Secondary to Antiretroviral Therapy: A Randomized Clinical Trial

Objective: The measurement of phase angles is an important monitoring parameter and supplementation with omega-3 could promote benefits by modulating the electrical potential of membranes and increasing body cell mass. This study aimed to evaluate the effectiveness of omega-3 fatty acid supplementation on the phase angle of people living with HIV/AIDS. Methods: In this study, 63 individuals of all genders who were undergoing outpatient follow-up and showed lipodystrophy due to highly active antiretroviral therapy were analyzed. Our sample consisted of two groups, one that received supplementation containing 2550 mg of omega-3/day (1080 mg of eicosapentaenoic acid and 720 mg of docosahexaenoic acid) for three months (n = 32) and another that underwent nutrition guidance (n = 31). Phase angle and body cell mass were assessed for both groups and compared at the beginning of research (T0) and after our intervention (T1) for each group separately. Results: Phase angle averaged 6.45° ± 1.06 SD. The comparison between T0 and T1 showed a significant increase in phase angle and body cell mass, whereas the guidance group showed a decrease in body cell mass at T1 in relation to T0, with a significant p-value. Variance in phase angle between moments showed significant values between T0 and T1 in the supplementation group for all genders. Conclusion: Omega-3 positively modulated patients phase angle and body cell mass, but we emphasize the need for other studies that can solidify knowledge about supplementation dosage and intervention time.