Friction behaviors in the metal cutting process:state of the art and future perspectives

Material removal in the cutting process is regarded as a friction system with multiple input and output variables.The complexity of the cutting friction system is caused by the extreme conditions existing on the tool–chip and tool–workpiece interfaces.The critical issue is significant to use knowledge of cutting friction behaviors to guide researchers and industrial manufacturing engineers in designing rational cutting processes to reduce tool wear and improve surface quality.This review focuses on the state of the art of research on friction behaviors in cutting procedures as well as future perspectives.First,the cutting friction phenomena under extreme conditions,such as high temperature,large strain/strain rates,sticking–sliding contact states,and diverse cutting conditions are analyzed.Second,the theoretical models of cutting friction behaviors and the application of simulation technology are discussed.Third,the factors that affect friction behaviors are analyzed,including material matching,cutting parameters,lubrication/cooling conditions,micro/nano surface textures,and tool coatings.Then,the consequences of the cutting friction phenomena,including tool wear patterns,tool life,chip formation,and the machined surface are analyzed.Finally,the research limitations and future work for cutting friction behaviors are discussed.This review contributes to the understanding of cutting friction behaviors and the development of high-quality cutting technology.

Impressive strides in amelioration of corrosion behavior of Mg-based alloys through the PEO process combined with surface laser process: A review

The unsatisfactory corrosion properties of Mg-based alloys pose a significant obstacle to their widespread application. Plasma electrolytic oxidation(PEO) is a prevalent and effective coating method that produces a ceramic-like oxide coating on the surface of Mg-based alloys,enhancing their resistance to corrosion. Research has demonstrated that PEO treatment can substantially improve the corrosion performance of alloys based on magnesium in the short term. In an effort to enhance the corrosion resistance of PEO coatings over an extended period of time, researchers have turned their attention to the use of laser processes as both pre-and post-treatments in conjunction with the PEO process. Various laser processes, such as laser shock melting(LSM), laser shock adhesion(LSA), laser shock texturing(LST), and laser shock peening(LSP), have been investigated for their potential to improve PEO coatings on Mg substrates and their alloys. These laser melting processes can homogenize and alter the microstructure of Mg-based alloys while leaving the bulk material unchanged, thereby modifying the substrate surface. However, the porous and rough structure of PEO coatings, with their open and interconnected pore structure, can reduce their long-term corrosion resistance. As such, various laser processes are well-suited for surface modification of these coatings. This study will first examine the PEO process and the various types of laser processes used in this process, before investigating the corrosion behavior of PEO coatings in conjunction with laser pre-and post-treatment processes.

NADARAYA-WATSON ESTIMATORS FOR REFLECTED STOCHASTIC PROCESSES

We study the Nadaraya-Watson estimators for the drift function of two-sided reflected stochastic differential equations.The estimates,based on either the continuously observed process or the discretely observed process,are considered.Under certain conditions,we prove the strong consistency and the asymptotic normality of the two estimators.Our method is also suitable for one-sided reflected stochastic differential equations.Simulation results demonstrate that the performance of our estimator is superior to that of the estimator proposed by Cholaquidis et al.(Stat Sin,2021,31:29-51).Several real data sets of the currency exchange rate are used to illustrate our proposed methodology.

Effects of friction stir processing and nano-hydroxyapatite on the microstructure,hardness,degradation rate and in-vitro bioactivity of WE43 alloy for biomedical applications

Nowadays,magnesium alloys are emerging in biomedical implants for their similar properties to natural bones.However,the rapid degradation of magnesium alloys in biological media hinders successful implantation.Refinement of microstructure,as well as reinforcement particles can significantly improve the degradation rate.In this work,multi-pass friction stir processing(FSP)was proposed to synthesize WE43/nano-hydroxyapatite(n HA)surface composite,the microstructure,reinforced particle distribution,micro-hardness,corrosion behavior and in-vitro bioactivity were studied.The subsequent FSP passes of WE43 alloy and WE43/n HA composite refined the grain size which was reduced by 94.29%and 95.92%(2.63 and 1.88μm,respectively)compared to base metal after three passes.This resulted in increasing the microhardness by 120%(90.86 HV0.1)and 135%(105.59 HV0.1)for the WE43 and WE43-n HA,respectively.It is found that increasing FSP passes improved the uniform distribution of n HA particles within the composite matrix which led to improved corrosion resistance and less degradation rate.The corrosion rate of the FSPed WE43/n HA composite after three passes was reduced by 38.2%(4.13 mm/year)and the degradation rate was reduced by 69.7%(2.87 mm/y).This is attributed to secondary phase(Mg24Y5and Mg41Nd5)particle fragmentation and redistribution,as well as a homogeneous distribution of n HA.Additionally,the growing Ca-P and Mg(OH)2layer formed on the surface represented a protective layer that reduced the degradation rate.The wettability test revealed a relatively hydrophilic surface with water contact angle of 49.1±2.2°compared to 71.2±2.1°for base metal.Also,biomineralization test showed that apatite layer grew after immersion 7d in simulated body fluid with atomic ratio of Ca/P 1.60 approaching the stoichiometric ratio(1.67)indicating superior bioactivity of FSPed WE43/n HA composite after three passes.These results raise that the grain refinement by FSP and introduction of n HA particles significantly improved the degradation rate and in-vitro bioactivity of WE43 alloy for biomedical applications.

Effect of safety valve types on the gas venting behavior and thermal runaway hazard severity of large-format prismatic lithium iron phosphate batteries

The safety valve is an important component to ensure the safe operation of lithium-ion batteries(LIBs).However,the effect of safety valve type on the thermal runaway(TR)and gas venting behavior of LIBs,as well as the TR hazard severity of LIBs,are not known.In this paper,the TR and gas venting behavior of three 100 A h lithium iron phosphate(LFP)batteries with different safety valves are investigated under overheating.Compared to previous studies,the main contribution of this work is in studying and evaluating the effect of gas venting behavior and TR hazard severity of LFP batteries with three safety valve types.Two significant results are obtained:(Ⅰ)the safety valve type dominates over gas venting pressure of battery during safety venting,the maximum gas venting pressure of LFP batteries with a round safety valve is 3320 Pa,which is one order of magnitude higher than other batteries with oval or cavity safety valve;(Ⅱ)the LFP battery with oval safety valve has the lowest TR hazard as shown by the TR hazard assessment model based on gray-fuzzy analytic hierarchy process.This study reveals the effect of safety valve type on TR and gas venting,providing a clear direction for the safety valve design.

High temperature deformation behavior and optimization of hot compression process parameters in TC11 titanium alloy with coarse lamellar original microstructure

The high temperature deformation behaviors of α＋β type titanium alloy TC11 （Ti-6.5Al-3.5Mo-1.5Zr-0.3Si） with coarse lamellar starting microstructure were investigated based on the hot compression tests in the temperature range of 950-1100 ℃ and the strain rate range of 0.001-10 s-1. The processing maps at different strains were then constructed based on the dynamic materials model, and the hot compression process parameters and deformation mechanism were optimized and analyzed, respectively. The results show that the processing maps exhibit two domains with a high efficiency of power dissipation and a flow instability domain with a less efficiency of power dissipation. The types of domains were characterized by convergence and divergence of the efficiency of power dissipation, respectively. The convergent domain in a＋fl phase field is at the temperature of 950-990 ℃ and the strain rate of 0.001-0.01 s^-1, which correspond to a better hot compression process window of α＋β phase field. The peak of efficiency of power dissipation in α＋β phase field is at 950 ℃ and 0.001 s 1, which correspond to the best hot compression process parameters of α＋β phase field. The convergent domain in β phase field is at the temperature of 1020-1080 ℃ and the strain rate of 0.001-0.1 s^-l, which correspond to a better hot compression process window of β phase field. The peak of efficiency of power dissipation in ℃ phase field occurs at 1050 ℃ over the strain rates from 0.001 s^-1 to 0.01 s^-1, which correspond to the best hot compression process parameters of ,8 phase field. The divergence domain occurs at the strain rates above 0.5 s^-1 and in all the tested temperature range, which correspond to flow instability that is manifested as flow localization and indicated by the flow softening phenomenon in stress-- strain curves. The deformation mechanisms of the optimized hot compression process windows in a＋β and β phase fields are identified to be spheroidizing and dynamic recrystallizing controlled by self-diffusion mechanism, respectively. The microstructure observation of the deformed specimens in different domains matches very well with the optimized results.

Hot deformation behavior and processing maps of Mg-Zn-Cu-Zr magnesium alloy

The deformation behaviors of a new quaternary Mg-6Zn-1.5Cu-0.5Zr alloy at temperatures of 523-673 K and strain rates of 0.001-1 s-1 were studied by compressive tests using a Gleeble 3800 thermal-simulator.The results show that the flow stress increases as the deformation temperature decreases or as the strain rate increases.A strain-dependent constitutive equation and a feed-forward back-propagation artificial neural network were used to predict flow stress,which showed good agreement with experimental data.The processing map suggests that the domains of 643-673 K and 0.001-0.01 s-1 are corresponded to optimum conditions for hot working of the T4-treated Mg-6Zn-1.5Cu-0.5Zr alloy.

Hot deformation behavior of spray forming LSHR alloy using constitutive equation and processing map

Flow behaviors of spray forming low solvus high refractory (LSHR) alloy were investigated using hot compression tests performed on a Gleeble?3500 thermal mechanical simulator at temperatures of 1020?1150 °C and strain rates of 0.0003?1.0 s?1. The constitutive equation was established, power dissipation (η) maps and hot processing maps were plotted. The microstructure evolution and dislocation distribution of domains with different values of η in power dissipation maps were also observed. The results show that the flow stress increases with decreasing temperature and increasing strain rate. The activation energy of the spray forming LSHR alloy is 1243.86 kJ/mol. When the value of η is 0.36 at the strain of 0.5, the domain in the processing map shows characteristics of typical dynamic recrystallization (DRX) and low dislocation density. According to the microstructure evolution and processing maps, the optimum processing condition for good hot workability of spray forming LSHR alloy can be summed up as:temperature range 1110?1150 °C; strain rate range 0.01?0.3 s?1.

Constitutive behavior, microstructural evolution and processing map of extruded Al-1.1Mn-0.3Mg-0.25RE alloy during hot compression

Hot compression tests of an extruded Al-1.1Mn-0.3Mg-0.25RE alloy were performed on Gleeble-1500 system in the temperature range of 300-500 ℃ and strain rate range of 0.01-10 s-l. The associated microstructural evolutions were studied by observation of optical and transmission electron microscopes. The results show that the peak stress level decreases with increasing deformation temperature and decreasing strain rate, which can be represented by a Zener-Hollomon parameter in the hyperbolic-sine equation with the hot deformation activation energy of 186.48 kJ/mol. The steady flow behavior results from dynamic recovery whereas flow softening is associated with dynamic recrystallization and dynamic transformation of constituent particles. The main constituent particles are enriched rare earth phases. Positive purifying effects on impurity elements of Fe and Si are shown in the Al-l.lMn-0.3Mg-0.25RE alloy, which increases the workability at high temperature. Processing map was calculated and an optimum processing was determined with deformation temperature of 440-450 ℃ and strain rate of 0.01 s-1.

Effect of melting temperature on microstructural evolutions, behavior and corrosion morphology of Hadfield austenitic manganese steel in the casting process

In this study, the effect of melting temperature on the microstructural evolutions, behavior, and corrosion morphology of Hadfield steel in the casting process is investigated. The mold was prepared by the sodium silicate/CO_2 method, using a blind riser, and then the desired molten steel was obtained using a coreless induction furnace. The casting was performed at melting temperatures of 1350, 1400, 1450, and 1500°C, and the cast blocks were immediately quenched in water. Optical microscopy was used to analyze the microstructure, and scanning electron microscopy(SEM) and X-ray diffractrometry(XRD) were used to analyze the corrosion morphology and phase formation in the microstructure, respectively. The corrosion behavior of the samples was analyzed using a potentiodynamic polarization test and electrochemical impedance spectroscopy(EIS) in 3.5 wt% NaCl. The optical microscopy observations and XRD patterns show that the increase in melting temperature led to a decrease of carbides and an increase in the austenite grain size in the Hadfield steel microstructure. The corrosion tests results show that with increasing melting temperature in the casting process, Hadfield steel shows a higher corrosion resistance. The SEM images of the corrosion morphologies show that the reduction of melting temperature in the Hadfield steel casting process induced micro-galvanic corrosion conditions.

Rheological behavior of ZnO suspension with thermosensitive poly(N-isopropylacrylamide) for colloidal processing of ceramics

Novel colloidal processing using thermosensitive poly（N-isopropylacrylamide） （PNIPAM） as a coagulating agent has beendeveloped to prepare complex-shaped ceramic components. In this work, the properties of PNIPAM aqueous solutions and therheological behavior of ZnO suspensions with PNIPAM were investigated. The results show that the PNIPAM solutions exhibitobvious thermosensitivity and its transition temperature is around 32℃. When the temperature is above 40℃ （Tc, the criticaltransition temperature of thermosensitive suspension）, the 50% ZnO （volume fraction） suspension with 8 mg/mL PNIPAM has asharp increase in viscosity and reaches up to 11.49 Pa·s at 50℃, displaying strong elasticity. The main reasons are the increase ofeffective volume fraction attributed to precipitation of PNIPAM segments and the flocculation between ZnO powder particles. Inaddition, the maximum solid loading （volume fraction） at 20 ℃ is higher than that at 40℃, which proves that the phase transition ofPNIPAM can induce the flocculation of suspension.

Characterization of hot deformation behavior of AA2014 forging aluminum alloy using processing map

The hot deformation behavior of AA2014forging aluminum alloy was investigated by isothermal compression tests attemperatures of350-480°C and strain rates of0.001-1s-1on a Gleeble-3180simulator.The corresponding microstructures of thealloys under different deformation conditions were studied using optical microscopy(OM),electron back scattered diffraction(EBSD)and transmission electron microscopy(TEM).The processing maps were constructed with strains of0.1,0.3,0.5and0.7.The results showed that the instability domain was more inclined to occur at strain rates higher than0.1s-1and manifested in theform of local non-uniform deformation.At the strain of0.7,the processing map showed two stability domains:domain I(350-430°C,0.005-0.1s-1)and domain II(450-480°C,0.001-0.05s-1).The predominant softening mechanisms in both of the twodomains were dynamic recovery.Uniform microstructures were obtained in domain I,and an extended recovery occurred in domainII,which would lead to the potential sub-grain boundaries progressively transforming into new high-angle grain boundaries.Theoptimum hot working parameters for the AA2014forging aluminum alloy were determined to be370-420°C and0.008-0.08s-1.

Processing map and hot deformation behavior of squeeze cast 6082 aluminum alloy

The hot deformation behavior and microstructure evolution of 6082 aluminum alloy fabricated through squeeze casting(SC)under different pressures were studied.The alloy was subjected to hot compression tests and 3D hot processing maps were established.The microstructure evolution was studied by optical microscope(OM),scanning electron microscope(SEM),and electron backscattered diffraction(EBSD).It is found that more dynamic recrystallization(DRX)grains are generated during the deformation of the specimen fabricated under higher SC pressure.At high temperature the effect of SC pressure on microstructure evolution weakens due to the dissolution of second phase particles.In addition,uneven second phase particles in specimens fabricated under higher SC pressure compressed with low temperature and middle strain rate would result in flow localization instability.Finally,the optimum deformation conditions for the 6082 aluminum alloy fabricated by SC were obtained at the temperatures of 430−500℃ and the strain rates of 0.01−1 s^(−1).

Constitutive behavior and processing maps of a new wrought magnesium alloy ZE20 (Mg-2Zn-0.2Ce)

ZE20(Mg-2Zn-0.2Ce)^2 is a new wrought magnesium alloy with improved extrudability and mechanical properties[1].To understand the constitutive behavior and workability of this new alloy,Gleeble thermomechanical testing has been carried out in this study.The flow stress behavior of ZE20 was investigated between 250℃–450℃ and 10^–3 s^–1–1.0 s^–1 in isothermal compression.Constitutive descriptions of the flow stress are provided.A new general approach at application of the extended Ludwik equation is demonstrated and was found to be more accurate than the hyperbolic sine Arrhenius model while having a similar number of model constants.Processing maps were developed based on the experimental results and are verified with microstructural investigation.A region of safe processing with non-basal texture and high activity of dynamic recrystallization(DRX)was found between 375℃ and 450℃,from 10^–1 s^–1 to 10^–2.5 s^–1.A region of potentially safe processing with annealing that is associated with shear band nucleation of non-basal grains was identified for temperatures as low as 300℃ and rates as high as 10^–1 s^–1.

Hot deformation behaviors and processing maps of Mg-Zn-Er alloys based on Gleeble-1500 hot compression simulation

The hot deformation behaviors of as-solution Mg?xZn?yEr alloys (x/y=6, x=3.0, 4.5 and 6.0; y=0.50, 0.75 and 1.00) wereinvestigated on Gleeble?1500 thermal simulator in a temperature range of 200?450 °C at a strain rate of 0.001?1 s?1. The truestress?strain curves showed the dynamic competition between the working hardening and working softening mainly due to thedynamic recrystallization (DRX) occurring during hot compression. The constitutive equations were constructed which couldaccurately predict the peak stress of the alloys. The addition of Zn and/or Er resulted in higher deformation activation energy forMg?3Zn?0.5Er (alloy A). The processing maps were constructed as function of the temperature and the strain rate, providing theoptimum hot working conditions (i.e., at strain of 0.3, Mg?3Zn?0.5Er (alloy A): 380?430 ?C, <0.1 s?1; Mg?4.5Zn?0.75Er (alloy B):380?450 ?C, 0.01?0.1 s?1; Mg?6Zn?1Er (alloy C): 390?440 ?C, 0.01?0.1 s?1). The as-solution treated Mg?4.5Zn?0.75Er (alloy B)demonstrated more optimum hot working window comparing with Mg?3Zn?0.5Er (alloy A) and Mg?6Zn?1Er (alloy C).

Processing map and hot deformation behavior of Ta-particle reinforced TiAl composite

The hot deformation behavior of a Ta-particle reinforced TiAl composite was studied.Ti-48Al-2Cr-2Nb-0.2 W(at.%)/20 vol.%Ta metal matrix composite was fabricated by spark plasma sintering.The deformation behavior was investigated by hot compression tests at the temperature ranging from 1050 to 1200℃ and the strain rate ranging from 1×10-3 to 1 s-1.The constitutive equation containing true strain variables was established.The values of activation energy Q under different strain degrees are between 240 and 280 kJ/mol,which are lower than that of pure TiAl.Based on dynamic material modeling,the processing maps at various strain degrees were established,and the optimized parameters for hot working are 1050-1100℃ and 0.005-0.01 s-1.The microstructural evolution during deformation was characterized,which indicated that the dynamic recrystallization plays an important role in this process.

Synthetic Process of Bio-Based Phenol Formaldehyde Adhesive Derived from Demethylated Wheat Straw Alkali Lignin and Its Curing Behavior

Lignin is a natural biopolymer with a complex three-dimensional network, commercially obtained from wasteliquid of paper pulp and bioethanol production, and could be a candidate for preparation of environment-friendlybio-based polyphenol material. In the present work, the demethylated wheat straw alkali lignin (D-Lig), preparedby demethylation of wheat straw alkali lignin (Lig) using an in-situ generated Lewis acid, was used to synthesizebio-based phenol formaldehyde resin adhesive (D-LPF) applied in plywood. Effects of synthetic process’s factors,including lignin substitution for phenol, NaOH concentration and molar ratio of formaldehyde to phenol, on thebonding strength and free formaldehyde content of D-LPF were investigated in detail, and the optimum syntheticprocess of D-LPF was obtained as following: Lignin substitution for phenol 60%, NaOH concentration 5.0% andmolar ratio of formaldehyde to phenol 2.0, and under the optimum reaction condition, the D-LPF presented lower free formaldehyde content (0.18%) and higher bonding strength (2.19 MPa), which was better than those ofcontaining-lignin phenol formaldehyde resin adhesive (LPF). Additionally, the curing behavior of the adhesivewas studied by differential scanning calorimetry (DSC) combined with gel time. It can be obtained that D-LPFresin adhesive had the shortest gel time, and fastest curing rate, compared with those of PF and L-PF resin adhesives. The curing kinetics data was fitted well by Kissinger model using non-isothermal DSC method, and theaverage activation energy value was 85.3 kJ/mol, slightly higher than that of commercial PF resin, while lowerthan that of LPF (90.2 kJ/mol). Finally, based on the analytical results of high temperature fourier transform infrared spectroscopy (FTIR), a possible curing mechanism of D-LPF was proposed.

Effect of thermo-mechanical processing on microstructure and electrochemical behavior of Ti-Nb-Zr-V new metastable β titanium biomedical alloy

The influence of thermo-mechanical processing (TMP) on the microstructure and the electrochemical behavior of new metastableβ alloy Ti?20.6Nb?13.6Zr?0.5V (TNZV) was investigated. The TMP included hot working in belowβ transus, solution heat treatments at the same temperature and different cooling rates in addition to aging. Depending upon the TMP conditions, a wide range of microstructures with varying spatial distributions and morphologies of equiaxed/elongatedα andβ phases were attained, allowing for a wide range of electrochemical properties to be achieved. The corrosion behavior of the studied alloy was evaluated in a Ringer’s solution at 37 °C via open circuit potential?time and potentiodynamic polarization measurements.

Rheological Behaviors and Processing Windows of Low Viscosity Epoxy Resin for VIMP

The chemorheological behaviors of a low viscosity epoxy resin system （Huntsman 1564/3486） for vacuum infusion moulding process （VIMP） were studied with viscosity experiments.The dual-Arrhenius rheological model and the engineering viscosity model were established and compared with the experimental data.The result showed that the viscosity in the earlier stage calculated by dual-Arrhenius model were smaller than the experimental data,while the data calculated by the engineering model were larger.Combining the two models together can predict the rheological behaviors of the resin system in a more credible manner.The processing windows of the resin system for VIMP were determined based on the two models.The optimum processing temperature is 30-45 ℃.

Identification of Behavior of Voluntary Traceability and Analysis of Its Determinants: A Case Study of Hog Slaughtering and Processing Firms in Zhejiang Province,China

In recent years, the Chinese government has highlighted the importance of adopting hog safety/quality traceability, and a growing amount of research continues to entice firms to adopt traceability systems. In this study, a survey was conducted on a sample of pig slaughtering and processing firms in Zhejiang, China through personal interviews and emails. The aim of this study was to examine the determinants of firm behavior on the implementation of voluntary traceability systems with more stringent standards and controls than those of the mandatory system in China. The results revealed that motivation based on product quality improvement, capital ability and role perception （business type） had significantly positive relationships with a firm＇s voluntary traceability. Other incentives, such as operation improvement, recall risk reduction, reduced occurrence of safety issues, and technical strength were not found to be supportive in our study. This study provides an opportunity to better understand the determinants of firm behavior on voluntary traceability, particularly in light of the fact that some Chinese firms are facing the threat of criminal action for the use of illegal additives and the abuse of Clenbuterol. Policy recommendations on encouraging the implementation of pork safety voluntary traceability by hog slaughtering and processing firms are also discussed.