Preparation and tribological performances of Ni-P-multi-walled carbon nanotubes composite coatings

Multi-walled carbon nanotubes （MWNTs） were wet-milled in the presence of ammonia and cationic surfactant and then used as reinforcements to prepare Ni-P-MWNTs composite coatings by electroless plating. The tribological performances of the composite coatings under dry condition were investigated in comparison with 45 steel and conventional Ni-P coating, Micrographs show that short MWNTs with uniform length and open tips were obtained through the wet-milling process. The results of wear test reveal that the Ni-P-MWNTs composite coatings posses much better friction reduction and anti-wear performances when compared with 45 steel and Ni-P coating. Within the MWNTs content range of 0.74%-1.97%, the friction coefficient and the volume wear rate of the composite coatings decrease gradually and reach the minimum values of 0.08 and 6.22x10-15 m3/（N.m）, respectively. The excellent tribological performances of the composite coatings can be attributed to the introduction of MWNTs, which play both roles of reinforcements and solid lubricant during the wear process.

Effect of wear conditions on tribological properties of electrolessly-deposited Ni-P-Gr-SiC hybrid composite coating

The friction and wear properties of the electrolessly-deposited Ni-P-Gr-SiC composites were investigated. The effects of graphite content, load and rotation speed on the friction coefficient and wear resistance of the composite coatings were mainly investigated. The worn surface and cross section of the coatings were characterized by scanning electron microscopy and energy-dispersive X-ray analysis. The results show that the composite coatings reveal good antifriction and wear resistance due to the synergic effect of graphite and SiC particles. The formation of graphite-rich mechanically mixed layer （GRMML） on the surface of Ni-P-Gr-SiC coating contributes to the good tribological behavior of the wear counterparts and SiC particles play a load bearing role in protecting GRMML from shearing easily.

Microstructure and depositional mechanism of Ni-P coatings with nano-ceria particles by pulse electrodeposition

Nano-CeO2 （RE） particles were co-deposited into Ni-P binary composite coatings by applying pulse current （PC） under ultrasonic （U） field. Morphology, chemical content and crystal microstructure were characterized by environmental scanning electron microscopy （E-SEM） with energy dispersive X-ray analysis （EDXA）, XRD diffractometry and transmission electron microscopy （TEM）. Experimental results show that Ni-P coating reinforced with 15g/L nano-CeO2, in amorphous state and with compact structure, can be improved in the microhardness from HV0.2580 to HV0.2780 by annealing at 600 °C for 2 h. The highest content of codeposited Ce and deposition rate can reach 2.3% and 68 μm/h, respectively. Furthermore, the effect of RE adsorption and pulse overpotential on depositional mechanism was investigated. n-CeO2 particles or Ce4＋ ions with strong adsorption capacity acted as the catalytic nucleus to improve densification effectively. During annealing at 600 °C for 2 h, n-CeO2 particles will uniformly adsorb on crystal grain to preferentially pad and heal up gaps of cracking Ni boundaries, promoting dispersion strengthening with refiner-grained structure.

Characteristics of microstructure and performance of laser-treated electroless Ni-P/Ni-W-P duplex coatings

Characteristics of microstructures of electroless Ni-P/Ni-W-P duplex coatings were investigated using SEM/EDX and XRD analysis techniques. Microhardness and wear behaviour of the coatings before and after laser crystallization were evaluated by measurements of hardnesses of coating surface and cross-section, and by unlubricated friction and wear experiments. The results indicate that it is possible to prepare electroless Ni-P/Ni-W-P duplex coatings by sequential immersion in two different plating baths. After laser crystallization, the microstructures of electroless Ni-P/Ni-W-P duplex coatings present the characteristics of higher degree of crystallization and larger grain size for outer layer Ni-W-P than inner Ni-P, but outer layer has a higher hardness. The wear resistance of laser-treated duplex coatings in a given process parameter conditions is superior to the as-plated ones. Laser treatment was performed directly in air without argon protection, which provides the possibility for application of industrialized production.

Crystalline texture evolution, control of the tribocorrosion behavior, and significant enhancement of the abrasion properties of a Ni-P nanocomposite coating enhanced by zirconia nanoparticles

This paper describes an investigation of the effect of ZrO2 nanoparticles on the abrasive properties,crystalline texture developments,and tribocorrosion behavior of Ni-P nanostructured coatings.In the investigation,Ni-P and Ni-P-ZrO2 nanostructured coatings are deposited on St52 steel via the electroless method.Transmission electron microscopy(TEM),field emission scanning electron microscopy(FE-SEM),X-ray diffraction(XRD),energy dispersive spectroscopy(EDS),cyclic-static polarization tests in 3.5wt%NaCl solution,the tribocorrosion test(by back-and-forth wear in electrochemical cell),and the microhardness test using the Vickers method were performed to characterize and analyze the deposited coatings.The results of this study showed that the addition of ZrO2 nanoparticles to the Ni-P electroless bath produced the following:a sharp increase in wear and hardness resistance,the change of the wear mechanism from sheet to adhesive mode,the reduction of pitting corrosion resistance,significant reduction in the tribocorrosion protective properties,change in the preferred orientation of the crystalline texture coating from(111)to(200),increase in the sedimentation rate during the deposit process,and a sharp increase in the thickness of the Ni-P nanostructured coatings.

Mechanical assisted electroless barrel-plating Ni-P coatings on magnesium alloy

A mechanically assisted electroless barrel-plating Ni-P was carried out in a rolling drum containing Mg alloy specimens and ceramic balls, which was submerged in a bath containing electroless plating solution deposited by this novel technique have a It is demonstrated that the Ni-P coatings crystallized Ni-P solid solution structure, showing fine-grains, higher hardness, and higher corrosion resistance compared with the conventional electroless plated amorphous Ni-P coatings. After heat treatment at 400 ℃ for 1 h, the structure of such Ni-P coatings were transformed to a structure with Ni-Ni3P double phases, and cracks in these coatings could not be observed, whereas cracks appeared seriously in the conventional electroless plated Ni-P coating after same heat treatment. Therefore, both hardness and corrosion resistance of these Ni-P coatings can be improved further by heat treatment. All of these beneficial effects can be attributed to the role of mechanical attrition during the mechanically assisted electroless barrel-plating process.

High-temperature tribological properties of Ni-P alloy coatings deposited by electro-brush plating

High-temperature tribological properties of Ni-P alloy coatings processed by electro-brush plating on 20CrMo steel have been investigated. A baU-on-disc configuration was employed and 4 mm diameter Si3N4 balls were used as static counterpart. All the wear tests were carried out at 450℃ for 180 rain without lubricants. The electro-brush plating Ni-P coating is amorphous in as-deposited condition, and it becomes polycrystalline with the formation of Ni and Ni3P after heat treatment at 450℃for 1 h. The friction coefficient of the Ni-P coating is just 50% of that of the 20CrMo steel at the friction temperature of 450℃. A mild adhesive wear mechanism was found for the electro-brush plating Ni-P coating tested at 450℃, whereas for the 20CrMo steel at the same temperature a mixed adhesive and abrasive wear mechanism was observed.

Evaluation of residual stress and corrosion behaviour of electroless plated Ni-P/Ni-Mo-P coatings

Single Ni-P and Ni-Mo-P coatings as well as duplex Ni-P/Ni-Mo-P coatings with the same compositions were prepared by electroless plating.The residual stresses of the coatings on the surface and cross sections were measured by nanoindentation and AFM analysis,and the corrosion behaviour of the coatings in10%HCl solution was evaluated by electrochemical methods,to establish the correlation between the residual stresses and corrosion behaviour of the coatings.The results showed that the single Ni-P and duplex Ni-P/Ni-Mo-P coatings presented residual compressive stresses of241and206MPa respectively,while the single Ni-Mo-P coating exhibited a residual tensile stress of257MPa.The residual compressive stress impeded the growth of the pre-existing porosity in the coatings,protecting the integrity of the coating.The duplex Ni-P/Ni-Mo-P coatings had better corrosion resistance than their respective single coating.In addition,the stress states affect the corrosive form of coatings.

Wear and Corrosion Resistance of Electroless Plating Ni-P Coating on P110 Steel

In order to improve the surface performance and increase the lifetime of P 110 oil casing tube steel during operation, electroless plating was conducted to form Ni-P coating onto its surface. The surface morphology/element distribution and phase constitution of the Ni-P coating were analyzed using scanning electron microscope （SEM） equipped with energy dispersive spectrometry （EDS） and X-ray diffraction （XRD）. Tribological and electrochemical measurement tests were applied to investigate the wear and corrosion resistance of P110 steel and the Ni-P coating. The results showed that a uniform and compact, high phosphorous Ni-P coating was formed. The obtained Ni-P coating indicated certain friction-reduction effect and lower mass loss during friction-wear tests. The Ni-P coating also exhibited higher corrosion resistance in comparison with bared P 110 steel. The obtained N i-P coating has significantly improved the surface performance of P110 steel.

Investigation on a Non-cyanide Plating Process of Ni-P Coating on Magnesium Alloy AZ91D

In this research we presented a non-cyanide plating process of Ni-P alloy coating on Mg alloy AZ91D. By applying a new process flow of electroless nickel plating in which zinc coating is used as transition of Ni-P coating on Mg alloy AZ91D, the process of copper transition coating plated in the cyanides bath can be replaced. A new bath composed of NiSO4 was established by orthogonal test. The results show that zinc transition coating can increase the adhesion and protect the Mg alloy substrate from the bath corrosion. The optimal plating bath composition is NiSO4·6H2O 20 g/L, NaH2PO2·H2O20g/L and C6H8O7·H2O 2.5 g/L, and optimal bath acidity and optimal plating temperature are pH 4.0 and 95℃, respectively. The present process flow is composed of ultrasonic cleaning→alkaline cleaning→acid pickling→activation→double immersing zinc→electroplating zinc→electroless nickel plating→passivation treatment. The present non-cyanide process of electroless nickel plating is harmless to our surroundings and Ni-P coating on Mg alloy AZ91D produced by present process possesses good adhesion and corrosion resistance.

Erosion and Toughening Mechanisms of Electroless Ni-P-Nano-NiTi Composite Coatings on API X100 Steel under Single Particle Impact

The addition of superelastic NiTi to electroless Ni-P coating has been found to toughen the otherwise brittle coatings in static loading conditions, though its effect on erosion behaviour has not yet been explored. In the present study, spherical WC-Co erodent particles were used in single particle impact testing of Ni-P-nano-NiTi composite coatings on API X100 steel substrates at two average velocities—35 m/s and 52 m/s. Erosion tests were performed at impact angles of 30°, 45°, 60°, and 90°. The effect of NiTi concentration in the coating was also examined. Through examination of the impact craters and material response at various impact conditions, it was found that the presence of superelastic NiTi in the brittle Ni-P matrix hindered the propagation of cracks and provided a barrier to crack growth. The following toughening mechanisms were identified: crack bridging and deflection, micro-cracking, and transformation toughening.

Effect of hydrogen on the friction and wear of Ni-P coatings

The effects of charging and outgassing on the friction and wear of Ni-P amorphous and nanocrystalline coatings were studied under ambient humidity and temperature.The results indicate that hydrogen charging can greatly decrease the volume loss during friction and increase the wear durability.However,the wear durability can be restored after outgassing.There are many cracks on the brittle nanocrystalline before charging,and no crack appears after charging,but there are only a few cracks on the outgassed sample.This indicates that hydrogen charging can inhibit the crack formation during friction for the brittle Ni-P nanocrystalline.For the charged sample,after the surface layer was removed by polishing,the wear track and the friction coefficient are consistent with those of an uncharged sample.The friction coefficient of the charged amorphous coating is very small within the first 140 s and then increases suddenly to the value corresponding to the uncharged sample.The absorbed surface layer lubricates the surface,reduces the friction coefficient,and improves the wear durability.

Quality of Electroless Ni-P (Nickel-Phosphorus) Coatings Applied in Oil Production Equipment with Salinity

The corrosion resistance of nickel-phosphorus (Ni-P) coatings and their mechanical properties in seawater have led inestigations into the development of new technologies and the replacement of some special alloys in equipment used in oil production, such as valves, tubing, sucker rod joints, pumps, riser, manifolds and subsea Christmas trees. These studies began with Brenner and Riddel who developed, in the 1940s, formulations for Ni-P deposition on carbon steel without using an electric current. Joint deposition of nickel and phosphorus on a metallic surface (carbon steel) without applying an external current is accomplished using cathodic reduction with hydrogen (H) from a reducing agent (sodium hypophosphite) and nickel salts. To assure good performance of a Ni-P coating, the deposit quality must be inspected and evaluated during the chemical deposition process or in the end product. The recommended test parameters are: thickness, layer uniformity, hardness, adhesion, porosity, corrosion resistance and chemical composition of the nickel-phosphorus coating. The purpose of this paper was to investigate the Ni-P coating process, to evaluate the b?haviour of Ni-P in a saline environment using aqueous brine (3.5% - 30% sodium chloride by mass) and to present possible defects that could compromise the coating.

化学镀(Ni-P)-PTFE复合镀层的研究现状与展望

综述了近年来国内外在 (Ni P) PTFE复合镀方面的研究进展。重点探讨了表面活性剂、pH值、温度、搅拌方式等工艺参数对复合镀层中粒子分布及含量的影响 ,同时也讨论了复合镀层的几个重要性能 ,特别是摩擦磨损性能的研究。最后指出自润滑 (Ni P) PTFE将有着更为广阔的发展前景。

(Ni-P)-PTFE化学复合镀工艺优化及性能研究

通过正交试验方法,研究(Ni-P)-PTFE化学复合镀工艺,得到了最佳配方及工艺参数,对镀层的形貌、硬度、厚度、孔隙率和耐蚀性能进行了检测和评价。实验结果表明,最佳配方及工艺条件为:32g/L硫酸镍、24g/L次磷酸钠、16g/L柠檬酸钠、20g/L乙酸钠、20mL/L乳酸、8g/L丁二酸、4g/L聚四氟乙烯、0.01g/L十二烷基磺酸钠,pH为5,θ为90℃,施镀时间t为2.5h。在该工艺条件下,镀层硫酸铜点滴时间t可达312s,具有良好的耐腐蚀性;沉积速率达28.6g/(m2·h);镀层表面较平整,孔隙率较低,无起皮和脱落,与基体结合良好。

有机玻璃化学复合镀(Ni-P)-PTFE工艺

通过实验研究发现 :聚甲基丙烯酸甲酯 (PMMA ,俗称有机玻璃 ) ,经过一系列恰当的预处理如硫磷混酸粗化、化学镀铜等工艺后 ,可以采用含稳定剂、缓冲剂及四种络合剂配合使用的低温酸性化学复合镀的方法 ,得到 (Ni P)PTFE镀层 ,该工艺具有沉积温度低 ( 68～ 70 )℃ ,镀速高 ( 8～ 12 μm/h) ,镀液稳定等特点。经镀层性能测试。结果表明 :该镀层与基体结合力优异 ,耐蚀性良好。该工艺成本低廉宜于推广应用。

High-temperature Compressive Performance of Mg Alloy Foams Coated with Ni-P Layer

Mg/Ni hybrid foams were fabricated by the electroless method.The Ni-P(Nickel-Phosphorous)coatings were deposited on the surface of closed-cell Mg alloy foams.The composition,microstructure and phases of the Ni-P coatings were characterized by scanning electron microscopy(SEM),energy-dispersive X-ray spectroscopy(EDS)and X-ray diffraction(XRD),respectively.The compressive tests were performed on the Mg/Ni hybrid foams at 400℃using the Mg alloy foams as a reference.The experimental results show that the yield strength,plateau stress and energy absorption capacity of the closed-cell Mg alloy foams at high temperature were improved by the Ni-P coating.And there are four main modes for the Mg/Ni hybrid foam failure at 400℃,i e,shearing in cell wall,bending in cell edge,shedding and cracking in Ni-P coating.

Ni–P coating on AZ31 magnesium alloy and its crystallization

Amorphous Ni-P coating was plated on AZ31 magnesium alloy via the electroless plating technique, and the plated alloy was subsequently annealed. X-ray dif- fraction （XRD）, scanning electron microscopy （SEM）, energy dispersive spectroscopy （EDS）, and differential scanning calorimetry （DSC） were used to characterize the coating. The results show that the hardness of the coating is much higher than that of bare magnesium alloy, which further increases after crystallization. The electrochemical polarization and salt spray tests show that the coating exhibits a much higher corrosion resistance than that of the bare magnesium alloy. Moreover, the crystallized coating still exhibits a much stronger corrosion resistance than that of the bare magnesium alloy, although its corrosion resistance is lower than that of the as-plated one.

EFFECTS OF DEPOSITION PROCESS ON PHOSPHORUS CONTENT IN ELECTROLESS Ni－P COATINGS

There are many factors that affect the phosphorus content in the electroless Ni-P coatings The effects of the compositions of plating solution,the PH values of plat ing solution and the deposition temperature on the phosphorus content in Ni-P coatings were investigated in this paper It is found that the phosphorus content in Ni-P coatings increases and the deposition rate decreases with decreasing PH values,nickel sulphate NiSO4 content of plating solution and the deposition temperature.

Electroless Ni-P plating on Mg-Li alloy by two-step method

Pretreated Mg-Li alloy sheets were pre-plated in a NiCO3？2Ni（OH）2？4H2O solution to form a thin Ni-P alloy film and then plating in a NiSO4？6H2O solution was carried out to obtain a protective coating.The surface morphology,structure and corrosion resistance of the coating were studied.The results showed that a flat,bright and compact plating layer,which was integrated into the matrix metal,was obtained.The P content of the Ni-P coating reached 13.56%（mass fraction）.The hardness value of the Ni-P coating was about HV 549.The polarization curve showed that the corrosion potential of the Ni-P coating reached ？0.249 V（vs SCE）.A long passivation region was found on the polarization curve,and this phenomenon indicated that the coating has an excellent anti-corrosion property.