A Cr/Cr2N/CrN multilayer coating with a thickness of 24.4 μm was deposited by multi-arc ion plating. The coating was systematically characterized by field emission scanning electron microscopy(FESEM), X-ray photoelec...A Cr/Cr2N/CrN multilayer coating with a thickness of 24.4 μm was deposited by multi-arc ion plating. The coating was systematically characterized by field emission scanning electron microscopy(FESEM), X-ray photoelectron spectrometry(XPS), energy dispersive spectroscopy(EDS), X-ray diffraction(XRD) and transmission electron microscopy(TEM). Hardness and adhesion were tested by nanoindentation and scratch tester, respectively. The friction properties were investigated by a reciprocating UMT-3MT ball-on-disk tribometer in air and seawater. The results showed that the multilayer coating consisted of three different layers, with Cr,Cr2N and CrN phases, respectively. Compared with CrN single layer coating, the adhesion of the multilayer coating was improved significantly, the hardness of the multilayer coating was(21±2) GPa. The corrosion resistance of the multilayer coating was also improved in artificial seawater. The friction coefficient of multilayer coating was lower than that of CrN single layer coating both in air and seawater.展开更多
In the present work,TiAlN coatings were deposited on Ti(C,N)-based cermet substrates by physical vapor deposition method.Emphasis was focused on the influence of grain size of cermet substrates on the microstructure,g...In the present work,TiAlN coatings were deposited on Ti(C,N)-based cermet substrates by physical vapor deposition method.Emphasis was focused on the influence of grain size of cermet substrates on the microstructure,growth behavior,mechanical properties,adhesion strength and wear behavior of the coatings.The results show that finer Ti(C,N)grain size leads to higher nucleation density and lower growth rate of coatings,indicating the crystallite size of the TiAlN coatings decreases with decreasing Ti(C,N)grain size.Nanoindentation tests show that the coatings deposited on cermets of the finest grain size exhibit the highest hardness(H),elastic modulus(E),H/E and H3/E2 of 34.5 GPa,433.2 GPa,0.080 and 0.22,respectively.The adhesion strength between coating and substrate is also enhanced with decreasing Ti(C,N)grain size by scratch test,which corresponds to the grain size and H/E and H3/E2 of the coating.Besides,the lower surface roughness and better mechanical properties of the coating deposited on finer grained cermet contribute to the better wear resistance of the coating.展开更多
A series of single bcc,bcc plus fcc duplex and single fcc microcrystalline coatings of 1Cr18Ni9Ti stainless steel were prepared by using sputtering technique.The resistance against pitting corrosion was studied by mea...A series of single bcc,bcc plus fcc duplex and single fcc microcrystalline coatings of 1Cr18Ni9Ti stainless steel were prepared by using sputtering technique.The resistance against pitting corrosion was studied by measurements of pitting corrosion potentials and electrochemical noise during initiation of corrosion pits.The results show that the sputtered coatings with single bcc phase or single fcc structure are more resistant to pitting corrosion than those with bcc plus fcc duplex phase structure.展开更多
Ternary Ti-B-N coatings were synthesized on AISI 304 and Si wafer by plasma-enhanced chemical vapor deposition (PECVD) technique using a gaseous mixture of TiCl4,BCl3,H2,N2,and Ar.By virtue of X-ray diffraction analys...Ternary Ti-B-N coatings were synthesized on AISI 304 and Si wafer by plasma-enhanced chemical vapor deposition (PECVD) technique using a gaseous mixture of TiCl4,BCl3,H2,N2,and Ar.By virtue of X-ray diffraction analysis,X-ray photoelectron spectroscopy,scanning electron microscope,and high-resolution transmission electron microscope,the influences of B content on the microstructure and properties of Ti B N coatings were investigated systematically.The results indicated that the microstructure and mechanical properties of Ti-B-N coatings largely depend on the transformation from FCC-TiN phase to HCP-TiB2 phase.With increasing B content and decreasing N content in the coatings,the coating microstructure evolves gradually from FCC-TiN/a-BN to HCP-TiB2 /a-BN via FCC-TiN+HCP-TiB2/a-BN.The highest microhardness of about 34 GPa is achieved,which corresponds to the nanocomposite Ti-63%B-N (mole fraction) coating consisting of the HCP-TiB2 nano-crystallites and amorphous BN phase.The lowest friction-coefficient was observed for the nanocomposite Ti-41%B-N (mole fraction) coating consisting of the FCC-TiN nanocrystallites and amorphous BN展开更多
Cr1-xAlxN coatings have been deposited on a Ti3Al based alloy by reactive sputtering method. The results of the isothermal oxidation test at 800-900℃ showed that Cr1-xAlxN coatings could remarkably reduce the oxidati...Cr1-xAlxN coatings have been deposited on a Ti3Al based alloy by reactive sputtering method. The results of the isothermal oxidation test at 800-900℃ showed that Cr1-xAlxN coatings could remarkably reduce the oxidation rate of the alloy owing to the formation of Al2O3＋Cr2O3 mixture oxide scale on the surface of the coatings. No spallation of the coatings or oxide scales took place during the cyclic oxidation at 800℃. Ti was observed to diffuse into the coatings, the diffusion distance of which was very short, and the diffusion ability of it was proportional to the AI content in the coatings. Compared to Ti, Nb can diffuse much more easily through the whole coatings and oxide scales.展开更多
The effect of sputtered Ti-50Al-10Cr and Ti-50A1-20Cr coatings on both isothermal and cyclic oxidation resistance at 800-900℃ and hot corrosion resistance at 850℃ of Ti-24Al-14Nb-3V was investigated. Results indicat...The effect of sputtered Ti-50Al-10Cr and Ti-50A1-20Cr coatings on both isothermal and cyclic oxidation resistance at 800-900℃ and hot corrosion resistance at 850℃ of Ti-24Al-14Nb-3V was investigated. Results indicated that Ti-24Al-14Nb-3V alloys exhibited poor oxidation resistance due to the formation of Al2O3+TiO2+AlNbO4 mixed scales in air at 800-900℃ and poor hot corrosion resistance due to the spoliation of scales formed in Na2SO4+K2SO4 melts at 850℃. Both Ti-50Al-10Cr and Ti-50Al-20Cr coatings remarkably improved the oxidation and hot corrosion resistance of Ti-24Al-14Nb-3V alloy.展开更多
Magnetron sputtered (Ti, Al)N monolayer and TiN/(Ti, Al)N multilayer coatings grown on cemented carbide substrates were studied by using energy dispersive X-ray spectroscopy (EDX), scanning electron microscopy(SEM), n...Magnetron sputtered (Ti, Al)N monolayer and TiN/(Ti, Al)N multilayer coatings grown on cemented carbide substrates were studied by using energy dispersive X-ray spectroscopy (EDX), scanning electron microscopy(SEM), nanoindentation, Rockwell A indentation test, strength measurements and cutting tests. The results show that the (Ti, Al)N monolayer and TiN/(Ti, Al)N multilayer coatings perform good affinity to substrate, and the TiN/(Ti, Al)N multilayer coating exhibits higher hardness, higher toughness and better cutting performance compared with the (Ti, Al)N monolayer coating. Moreover, the strength measurement indicates that the physical vapour deposition (PVD) coating has no effect on the substrate strength.展开更多
Fe-Cr-Ti-C composite powder was synthesized by precursor carbonization-composition process using the mixture of ferrotitanium, chromium, iron powder and precursor sucrose as raw material. And then the Fe-Cr-Ti-C coati...Fe-Cr-Ti-C composite powder was synthesized by precursor carbonization-composition process using the mixture of ferrotitanium, chromium, iron powder and precursor sucrose as raw material. And then the Fe-Cr-Ti-C coating was prepared by reactive plasma cladding method. Microstructure of the samples was observed by scanning electron microscope （SEM）, the phases were determined by X-ray diffraction （XRD）, and the wear resistance was evaluated under dry sliding wear test conditions at room temperature. Results indicate that the composite coating consists of primary austenite and dendritic eutectic austenite, chrysanthemum-shaped eutectic （Cr, Fe ） 7 C3 and TiC carbide. TiC presents the gradient distribution and different shapes in the coating, corresponding to equiaxial structure both in fusion zone and central zone, while it presents dendritic structure on the surface, respectively. The wear mass loss is insensitive to load for the coating while it increases rapidly for Q235 steel base metal in this test. The wear mass loss ofQ235 steel is 14 times as that of the composite coating under applied load of 40 kg.展开更多
The hardness, toughness and electrochemical properties of the CrN coatings were studied by the method of Ion Beam Enhanced DePosition(IBED). The results show that the fraction of CrN phase and its hardness increase wi...The hardness, toughness and electrochemical properties of the CrN coatings were studied by the method of Ion Beam Enhanced DePosition(IBED). The results show that the fraction of CrN phase and its hardness increase with increasing N2 partial pressure and N ions bombarding energy in a certain range, but the toughness decreases. When the N ions: Cr atoms ratio changes from 1. 45 × 1O-2, 3. 67 × 10-2 to 5. 87 ×10 - 2, Cr2O3 is produced. In terms of corrosion resistance, the coated specimen shows a slight improvement in comparison with substrate 52100 steel. The Cr-N coated specimen is characterized with pitting corrosion by penetrating the agent throngh the defects involved very thin coating layer.展开更多
The fine rnicrostrueture of the Y-modified ion plated Ti(Y)N coating/substrate steel A3 system has been examined by means of TEM and microdiffraction technique.It was revealed that the interface consists of 3 sublayer...The fine rnicrostrueture of the Y-modified ion plated Ti(Y)N coating/substrate steel A3 system has been examined by means of TEM and microdiffraction technique.It was revealed that the interface consists of 3 sublayers,i.e.α-Fe+Y_6Fe_(23),Ti+Y+FeTi and Ti_2N+YN +Ti_xN_y.The thicknesses of them are about 200,50 and 120 nm respectively.The phases in the transition area seem to have certain orientation relations.The mechanism of interface formation has also been discussed.展开更多
The composite metastable(Ti0.5Al0.5)N,(Ti0.45Al0.45Cr0.1)N and(Ti0.35Al0.35Cr0.3)N coatings were respectively deposited on a wrought martensite steel 1Cr11Ni2W2MoV for aero-engine compressor blades by arc ion plating ...The composite metastable(Ti0.5Al0.5)N,(Ti0.45Al0.45Cr0.1)N and(Ti0.35Al0.35Cr0.3)N coatings were respectively deposited on a wrought martensite steel 1Cr11Ni2W2MoV for aero-engine compressor blades by arc ion plating technique with pulse substrate bias. All the coatings have B1NaCl phase with a(200) preferred orientation and dense structures. The results show that the introduction of Cr into(Ti,Al)N gives rise to a minute shrinkage of crystal lattice. The incorporation of chromium into the coatings dramastically improves the oxidation-resistance of the coatings. For(Ti0.5Al0.5)N,a layered oxide scale forms after 100 h oxidation and the outer layer is the blend oxide of TiO2 and Al2O3,and the middle layer is rich in Al and the inner layer is rich in Ti. For(Ti0.45Al0.45Cr0.1)N,the oxide scale possesses a double-layered structure and the outer layer is rich in Ti. For(Ti0.35Al0.35Cr0.3)N,a Cr-rich compound oxide scale of Ti,Al and Cr forms,and a out-diffusion of Fe from steel to the nitride coating and oxide film during the oxidation takes place.展开更多
CrN and Cr-Al-N coatings were deposited by reactive magnetron sputtering on the glass substrate,and their corrosion behavior was studied. The electrochemical tests using both DC(polarization curves) and AC techniques(...CrN and Cr-Al-N coatings were deposited by reactive magnetron sputtering on the glass substrate,and their corrosion behavior was studied. The electrochemical tests using both DC(polarization curves) and AC techniques(EIS) were carried out on Potentiostat/Galvanstat(EG&G) in 3.5%(mass fraction) NaCl solution. After immersed into NaCl solution for 1 h,the mass of the CrN coating keeps constant with the time continuing. This can be explained by the passivation of the coating. The comparison between the corrosion potential(φcorr) of the Cr-Al-N coatings with different aluminum contents reveals that the corrosion potentials of the aluminum contain coatings are nobler than that of the CrN coatings. This means that the addition of aluminum shifts the corrosion potential to more positive potential value. Among these coatings,CrN in NaCl solution exhibits the worst corrosion resistance,while the corrosion resistance of Cr0.63Al0.37N in NaCl solution is the best. The polarization data and EIS data suggest that addition of aluminum can improve the corrosion resistance of CrN coating.展开更多
基金Project(51475449)supported by the National Natural Science Foundation of China
文摘A Cr/Cr2N/CrN multilayer coating with a thickness of 24.4 μm was deposited by multi-arc ion plating. The coating was systematically characterized by field emission scanning electron microscopy(FESEM), X-ray photoelectron spectrometry(XPS), energy dispersive spectroscopy(EDS), X-ray diffraction(XRD) and transmission electron microscopy(TEM). Hardness and adhesion were tested by nanoindentation and scratch tester, respectively. The friction properties were investigated by a reciprocating UMT-3MT ball-on-disk tribometer in air and seawater. The results showed that the multilayer coating consisted of three different layers, with Cr,Cr2N and CrN phases, respectively. Compared with CrN single layer coating, the adhesion of the multilayer coating was improved significantly, the hardness of the multilayer coating was(21±2) GPa. The corrosion resistance of the multilayer coating was also improved in artificial seawater. The friction coefficient of multilayer coating was lower than that of CrN single layer coating both in air and seawater.
基金Projects(51634006,51575368)supported by the National Natural Science Foundation of ChinaProject(2017GZ0041)supported by Science and Technology Support Program of Sichuan Province,China。
文摘In the present work,TiAlN coatings were deposited on Ti(C,N)-based cermet substrates by physical vapor deposition method.Emphasis was focused on the influence of grain size of cermet substrates on the microstructure,growth behavior,mechanical properties,adhesion strength and wear behavior of the coatings.The results show that finer Ti(C,N)grain size leads to higher nucleation density and lower growth rate of coatings,indicating the crystallite size of the TiAlN coatings decreases with decreasing Ti(C,N)grain size.Nanoindentation tests show that the coatings deposited on cermets of the finest grain size exhibit the highest hardness(H),elastic modulus(E),H/E and H3/E2 of 34.5 GPa,433.2 GPa,0.080 and 0.22,respectively.The adhesion strength between coating and substrate is also enhanced with decreasing Ti(C,N)grain size by scratch test,which corresponds to the grain size and H/E and H3/E2 of the coating.Besides,the lower surface roughness and better mechanical properties of the coating deposited on finer grained cermet contribute to the better wear resistance of the coating.
文摘A series of single bcc,bcc plus fcc duplex and single fcc microcrystalline coatings of 1Cr18Ni9Ti stainless steel were prepared by using sputtering technique.The resistance against pitting corrosion was studied by measurements of pitting corrosion potentials and electrochemical noise during initiation of corrosion pits.The results show that the sputtered coatings with single bcc phase or single fcc structure are more resistant to pitting corrosion than those with bcc plus fcc duplex phase structure.
基金funded by a grant from the National Core Research Center(NCRC)Program through the National Research Foundation of Korea funded by the Ministry of Education,Science and Technology(No.2012-0000-957)by a grant from the Fundamental R&D Program for Core Technology of Materials funded by the Ministry of Knowledge Economy,Republic of Korea
文摘Ternary Ti-B-N coatings were synthesized on AISI 304 and Si wafer by plasma-enhanced chemical vapor deposition (PECVD) technique using a gaseous mixture of TiCl4,BCl3,H2,N2,and Ar.By virtue of X-ray diffraction analysis,X-ray photoelectron spectroscopy,scanning electron microscope,and high-resolution transmission electron microscope,the influences of B content on the microstructure and properties of Ti B N coatings were investigated systematically.The results indicated that the microstructure and mechanical properties of Ti-B-N coatings largely depend on the transformation from FCC-TiN phase to HCP-TiB2 phase.With increasing B content and decreasing N content in the coatings,the coating microstructure evolves gradually from FCC-TiN/a-BN to HCP-TiB2 /a-BN via FCC-TiN+HCP-TiB2/a-BN.The highest microhardness of about 34 GPa is achieved,which corresponds to the nanocomposite Ti-63%B-N (mole fraction) coating consisting of the HCP-TiB2 nano-crystallites and amorphous BN phase.The lowest friction-coefficient was observed for the nanocomposite Ti-41%B-N (mole fraction) coating consisting of the FCC-TiN nanocrystallites and amorphous BN
基金the National Natural Science Foundation of China under grant Nos. 50371095 , 50571106.
文摘Cr1-xAlxN coatings have been deposited on a Ti3Al based alloy by reactive sputtering method. The results of the isothermal oxidation test at 800-900℃ showed that Cr1-xAlxN coatings could remarkably reduce the oxidation rate of the alloy owing to the formation of Al2O3＋Cr2O3 mixture oxide scale on the surface of the coatings. No spallation of the coatings or oxide scales took place during the cyclic oxidation at 800℃. Ti was observed to diffuse into the coatings, the diffusion distance of which was very short, and the diffusion ability of it was proportional to the AI content in the coatings. Compared to Ti, Nb can diffuse much more easily through the whole coatings and oxide scales.
文摘The effect of sputtered Ti-50Al-10Cr and Ti-50A1-20Cr coatings on both isothermal and cyclic oxidation resistance at 800-900℃ and hot corrosion resistance at 850℃ of Ti-24Al-14Nb-3V was investigated. Results indicated that Ti-24Al-14Nb-3V alloys exhibited poor oxidation resistance due to the formation of Al2O3+TiO2+AlNbO4 mixed scales in air at 800-900℃ and poor hot corrosion resistance due to the spoliation of scales formed in Na2SO4+K2SO4 melts at 850℃. Both Ti-50Al-10Cr and Ti-50Al-20Cr coatings remarkably improved the oxidation and hot corrosion resistance of Ti-24Al-14Nb-3V alloy.
文摘Magnetron sputtered (Ti, Al)N monolayer and TiN/(Ti, Al)N multilayer coatings grown on cemented carbide substrates were studied by using energy dispersive X-ray spectroscopy (EDX), scanning electron microscopy(SEM), nanoindentation, Rockwell A indentation test, strength measurements and cutting tests. The results show that the (Ti, Al)N monolayer and TiN/(Ti, Al)N multilayer coatings perform good affinity to substrate, and the TiN/(Ti, Al)N multilayer coating exhibits higher hardness, higher toughness and better cutting performance compared with the (Ti, Al)N monolayer coating. Moreover, the strength measurement indicates that the physical vapour deposition (PVD) coating has no effect on the substrate strength.
基金Supported by Natural Science Foundation of Shandong Province （No. ZR2011EMM017 ）.
文摘Fe-Cr-Ti-C composite powder was synthesized by precursor carbonization-composition process using the mixture of ferrotitanium, chromium, iron powder and precursor sucrose as raw material. And then the Fe-Cr-Ti-C coating was prepared by reactive plasma cladding method. Microstructure of the samples was observed by scanning electron microscope （SEM）, the phases were determined by X-ray diffraction （XRD）, and the wear resistance was evaluated under dry sliding wear test conditions at room temperature. Results indicate that the composite coating consists of primary austenite and dendritic eutectic austenite, chrysanthemum-shaped eutectic （Cr, Fe ） 7 C3 and TiC carbide. TiC presents the gradient distribution and different shapes in the coating, corresponding to equiaxial structure both in fusion zone and central zone, while it presents dendritic structure on the surface, respectively. The wear mass loss is insensitive to load for the coating while it increases rapidly for Q235 steel base metal in this test. The wear mass loss ofQ235 steel is 14 times as that of the composite coating under applied load of 40 kg.
文摘The hardness, toughness and electrochemical properties of the CrN coatings were studied by the method of Ion Beam Enhanced DePosition(IBED). The results show that the fraction of CrN phase and its hardness increase with increasing N2 partial pressure and N ions bombarding energy in a certain range, but the toughness decreases. When the N ions: Cr atoms ratio changes from 1. 45 × 1O-2, 3. 67 × 10-2 to 5. 87 ×10 - 2, Cr2O3 is produced. In terms of corrosion resistance, the coated specimen shows a slight improvement in comparison with substrate 52100 steel. The Cr-N coated specimen is characterized with pitting corrosion by penetrating the agent throngh the defects involved very thin coating layer.
文摘The fine rnicrostrueture of the Y-modified ion plated Ti(Y)N coating/substrate steel A3 system has been examined by means of TEM and microdiffraction technique.It was revealed that the interface consists of 3 sublayers,i.e.α-Fe+Y_6Fe_(23),Ti+Y+FeTi and Ti_2N+YN +Ti_xN_y.The thicknesses of them are about 200,50 and 120 nm respectively.The phases in the transition area seem to have certain orientation relations.The mechanism of interface formation has also been discussed.
基金Project (50401022) supported by the National Natural Science Foundation of ChinaProject (0650034) supported by the Natural Science Foundation of Jiangxi Province, China
文摘The composite metastable(Ti0.5Al0.5)N,(Ti0.45Al0.45Cr0.1)N and(Ti0.35Al0.35Cr0.3)N coatings were respectively deposited on a wrought martensite steel 1Cr11Ni2W2MoV for aero-engine compressor blades by arc ion plating technique with pulse substrate bias. All the coatings have B1NaCl phase with a(200) preferred orientation and dense structures. The results show that the introduction of Cr into(Ti,Al)N gives rise to a minute shrinkage of crystal lattice. The incorporation of chromium into the coatings dramastically improves the oxidation-resistance of the coatings. For(Ti0.5Al0.5)N,a layered oxide scale forms after 100 h oxidation and the outer layer is the blend oxide of TiO2 and Al2O3,and the middle layer is rich in Al and the inner layer is rich in Ti. For(Ti0.45Al0.45Cr0.1)N,the oxide scale possesses a double-layered structure and the outer layer is rich in Ti. For(Ti0.35Al0.35Cr0.3)N,a Cr-rich compound oxide scale of Ti,Al and Cr forms,and a out-diffusion of Fe from steel to the nitride coating and oxide film during the oxidation takes place.
基金Project (50371095) supported by the National Natural Science Foundation of China
文摘CrN and Cr-Al-N coatings were deposited by reactive magnetron sputtering on the glass substrate,and their corrosion behavior was studied. The electrochemical tests using both DC(polarization curves) and AC techniques(EIS) were carried out on Potentiostat/Galvanstat(EG&G) in 3.5%(mass fraction) NaCl solution. After immersed into NaCl solution for 1 h,the mass of the CrN coating keeps constant with the time continuing. This can be explained by the passivation of the coating. The comparison between the corrosion potential(φcorr) of the Cr-Al-N coatings with different aluminum contents reveals that the corrosion potentials of the aluminum contain coatings are nobler than that of the CrN coatings. This means that the addition of aluminum shifts the corrosion potential to more positive potential value. Among these coatings,CrN in NaCl solution exhibits the worst corrosion resistance,while the corrosion resistance of Cr0.63Al0.37N in NaCl solution is the best. The polarization data and EIS data suggest that addition of aluminum can improve the corrosion resistance of CrN coating.
