Material and structure made by additive manufacturing(AM)have received much attention lately due to their flexibility and ability to customize complex structures.This study first implements multiple objective topology...Material and structure made by additive manufacturing(AM)have received much attention lately due to their flexibility and ability to customize complex structures.This study first implements multiple objective topology optimization simulations based on a projectile perforation model,and a new topologic projectile is obtained.Then two types of 316L stainless steel projectiles(the solid and the topology)are printed in a selective laser melt(SLM)machine to evaluate the penetration performance of the projectiles by the ballistic test.The experiment results show that the dimensionless specific kinetic energy value of topologic projectiles is higher than that of solid projectiles,indicating the better penetration ability of the topologic projectiles.Finally,microscopic studies(scanning electron microscope and X-ray micro-CT)are performed on the remaining projectiles to investigate the failure mechanism of the internal structure of the topologic projectiles.An explicit dynamics simulation was also performed,and the failure locations of the residual topologic projectiles were in good agreement with the experimental results,which can better guide the design of new projectiles combining AM and topology optimization in the future.展开更多
We investigate the evolution of magnetic properties as well as the content and distribution of Mn for Mn(Sb_(1-x)Bi_(x))_(2)Te_(4) single crystals grown by large-temperature-gradient chemical vapor transport method.It...We investigate the evolution of magnetic properties as well as the content and distribution of Mn for Mn(Sb_(1-x)Bi_(x))_(2)Te_(4) single crystals grown by large-temperature-gradient chemical vapor transport method.It is found that the ferromagnetic MnSb_(2)Te_(4) changes to antiferromagnetism with Bi doping when x≥0.25.Further analysis implies that the occupations of Mn ions at Sb/Bi site Mn_(Sb/Bi) and Mn site Mn_(Mn) have a strong influence on the magnetic ground states of these systems.With the decrease of Mn_(Mn) increase of Mn_(Sb/Bi),the system will favor the ferromagnetic ground state.In addition,the rapid decrease of T_(C/N) with increasing Bi content when x ≤0.25 and the insensitivity of T_(N) to x when x> 0.25 suggest that the main magnetic interaction may change from the Ruderman-Kittel-Kasuya-Yosida type at low Bi doping region to the van-Vleck type in high Bi doped samples.展开更多
The interplay between topology and magnetism is vital for realizing exotic quantum phenomena,significant examples including quantum anomalous Hall effect,axion insulators,and high-order topological states.These states...The interplay between topology and magnetism is vital for realizing exotic quantum phenomena,significant examples including quantum anomalous Hall effect,axion insulators,and high-order topological states.These states host great potential for future applications in high-speed and low-consumption electronic devices.Despite being extensively investigated,practical platforms are still scarce.In this work,with molecular beam epitaxy(MBE),we provide the first experimental report on high-quality Bi(110)/CrTe_(2) magnetic heterostructure.By employing in-situ high-resolution scanning tunneling microscopy,we are able to examine the interaction between magnetism and topology.There is a potential edge state at an energy level above the Fermi level,but no edge states observed near the Fermi level The absence of high-order topological corner states near EF highlights the importance of lattice matching and interface engineering in designing high-order topological states.Our study provides key insights into the interplay between two-dimensional magnetic and topological materials and offers an important dimension for engineering magnetic topological states.展开更多
Large cavity structures are widely employed in aerospace engineering, such as thin-walled cylinders, blades andwings. Enhancing performance of aerial vehicles while reducing manufacturing costs and fuel consumptionhas...Large cavity structures are widely employed in aerospace engineering, such as thin-walled cylinders, blades andwings. Enhancing performance of aerial vehicles while reducing manufacturing costs and fuel consumptionhas become a focal point for contemporary researchers. Therefore, this paper aims to investigate the topologyoptimization of large cavity structures as a means to enhance their performance, safety, and efficiency. By usingthe variable density method, lightweight design is achieved without compromising structural strength. Theoptimization model considers both concentrated and distributed loads, and utilizes techniques like sensitivityfiltering and projection to obtain a robust optimized configuration. The mechanical properties are checked bycomparing the stress distribution and displacement of the unoptimized and optimized structures under the sameload. The results confirm that the optimized structures exhibit improved mechanical properties, thus offering keyinsights for engineering lightweight, high-strength large cavity structures.展开更多
This paper aims to propose a topology optimization method on generating porous structures comprising multiple materials.The mathematical optimization formulation is established under the constraints of individual volu...This paper aims to propose a topology optimization method on generating porous structures comprising multiple materials.The mathematical optimization formulation is established under the constraints of individual volume fraction of constituent phase or total mass,as well as the local volume fraction of all phases.The original optimization problem with numerous constraints is converted into a box-constrained optimization problem by incorporating all constraints to the augmented Lagrangian function,avoiding the parameter dependence in the conventional aggregation process.Furthermore,the local volume percentage can be precisely satisfied.The effects including the globalmass bound,the influence radius and local volume percentage on final designs are exploited through numerical examples.The numerical results also reveal that porous structures keep a balance between the bulk design and periodic design in terms of the resulting compliance.All results,including those for irregular structures andmultiple volume fraction constraints,demonstrate that the proposedmethod can provide an efficient solution for multiple material infill structures.展开更多
A three-dimensional coordination polymer,namely {[Zn2（tzba）（dmtrz）（OH）]·3H2O}n（1,H2tzba = 4-（5H-tetrazol）benzoic acid,Hdmtrz = 3,5-dimethyl-lH,l,2,4-triazole）,was hydrothermally synthesized and characte...A three-dimensional coordination polymer,namely {[Zn2（tzba）（dmtrz）（OH）]·3H2O}n（1,H2tzba = 4-（5H-tetrazol）benzoic acid,Hdmtrz = 3,5-dimethyl-lH,l,2,4-triazole）,was hydrothermally synthesized and characterized by single-crystal X-ray diffraction.It crystallizes in monoclinic system,P21/c space group with a = 8.018（11）,b = 21.04（3）,c = 11.069（14） A,β=91.26（3）°,V= 1867（4） A^3,Z = 4,Dc = 1.729 g/cm^3,F（000） = 984,μ= 2.614 mm^（-1）,R（F^2 〉 2σ（F^2）） =0.0612 and wR（F^2） = 0.1533.Topological analysis reveals that compound 1 is a（3,5）-connected structure with a Schlafli symbol of（4~2.6）（4~2.6~5.8~3）,which is a rarely observed lhh topology.In addition,the CO2 adsorption performance and luminescent property of 1 have also been studied.展开更多
基金sponsored by the National Key Research and Development Program of China[Grant Nos.2020YFC0826804 and 2022YFC3320504]the National Natural Science Foundation of China[Grant No.11772059]。
文摘Material and structure made by additive manufacturing(AM)have received much attention lately due to their flexibility and ability to customize complex structures.This study first implements multiple objective topology optimization simulations based on a projectile perforation model,and a new topologic projectile is obtained.Then two types of 316L stainless steel projectiles(the solid and the topology)are printed in a selective laser melt(SLM)machine to evaluate the penetration performance of the projectiles by the ballistic test.The experiment results show that the dimensionless specific kinetic energy value of topologic projectiles is higher than that of solid projectiles,indicating the better penetration ability of the topologic projectiles.Finally,microscopic studies(scanning electron microscope and X-ray micro-CT)are performed on the remaining projectiles to investigate the failure mechanism of the internal structure of the topologic projectiles.An explicit dynamics simulation was also performed,and the failure locations of the residual topologic projectiles were in good agreement with the experimental results,which can better guide the design of new projectiles combining AM and topology optimization in the future.
基金Project supported by the Beijing Natural Science Foundation (Grant No. Z200005)the National Key R&D Program of China (Grant Nos. 2022YFA1403800 and 2023YFA1406500)+1 种基金the National Natural Science Foundation of China (Grant No. 12274459)Collaborative Research Project of Laboratory for Materials and Structures, Institute of Innovative Research, Tokyo Institute of Technology。
文摘We investigate the evolution of magnetic properties as well as the content and distribution of Mn for Mn(Sb_(1-x)Bi_(x))_(2)Te_(4) single crystals grown by large-temperature-gradient chemical vapor transport method.It is found that the ferromagnetic MnSb_(2)Te_(4) changes to antiferromagnetism with Bi doping when x≥0.25.Further analysis implies that the occupations of Mn ions at Sb/Bi site Mn_(Sb/Bi) and Mn site Mn_(Mn) have a strong influence on the magnetic ground states of these systems.With the decrease of Mn_(Mn) increase of Mn_(Sb/Bi),the system will favor the ferromagnetic ground state.In addition,the rapid decrease of T_(C/N) with increasing Bi content when x ≤0.25 and the insensitivity of T_(N) to x when x> 0.25 suggest that the main magnetic interaction may change from the Ruderman-Kittel-Kasuya-Yosida type at low Bi doping region to the van-Vleck type in high Bi doped samples.
文摘The interplay between topology and magnetism is vital for realizing exotic quantum phenomena,significant examples including quantum anomalous Hall effect,axion insulators,and high-order topological states.These states host great potential for future applications in high-speed and low-consumption electronic devices.Despite being extensively investigated,practical platforms are still scarce.In this work,with molecular beam epitaxy(MBE),we provide the first experimental report on high-quality Bi(110)/CrTe_(2) magnetic heterostructure.By employing in-situ high-resolution scanning tunneling microscopy,we are able to examine the interaction between magnetism and topology.There is a potential edge state at an energy level above the Fermi level,but no edge states observed near the Fermi level The absence of high-order topological corner states near EF highlights the importance of lattice matching and interface engineering in designing high-order topological states.Our study provides key insights into the interplay between two-dimensional magnetic and topological materials and offers an important dimension for engineering magnetic topological states.
基金the National Natural Science Foundation of China and the Natural Science Foundation of Jiangsu Province.It was also supported in part by Young Elite Scientists Sponsorship Program by CAST.
文摘Large cavity structures are widely employed in aerospace engineering, such as thin-walled cylinders, blades andwings. Enhancing performance of aerial vehicles while reducing manufacturing costs and fuel consumptionhas become a focal point for contemporary researchers. Therefore, this paper aims to investigate the topologyoptimization of large cavity structures as a means to enhance their performance, safety, and efficiency. By usingthe variable density method, lightweight design is achieved without compromising structural strength. Theoptimization model considers both concentrated and distributed loads, and utilizes techniques like sensitivityfiltering and projection to obtain a robust optimized configuration. The mechanical properties are checked bycomparing the stress distribution and displacement of the unoptimized and optimized structures under the sameload. The results confirm that the optimized structures exhibit improved mechanical properties, thus offering keyinsights for engineering lightweight, high-strength large cavity structures.
基金This study is financially supported by StateKey Laboratory of Alternate Electrical Power System with Renewable Energy Sources(Grant No.LAPS22012).
文摘This paper aims to propose a topology optimization method on generating porous structures comprising multiple materials.The mathematical optimization formulation is established under the constraints of individual volume fraction of constituent phase or total mass,as well as the local volume fraction of all phases.The original optimization problem with numerous constraints is converted into a box-constrained optimization problem by incorporating all constraints to the augmented Lagrangian function,avoiding the parameter dependence in the conventional aggregation process.Furthermore,the local volume percentage can be precisely satisfied.The effects including the globalmass bound,the influence radius and local volume percentage on final designs are exploited through numerical examples.The numerical results also reveal that porous structures keep a balance between the bulk design and periodic design in terms of the resulting compliance.All results,including those for irregular structures andmultiple volume fraction constraints,demonstrate that the proposedmethod can provide an efficient solution for multiple material infill structures.
文摘A three-dimensional coordination polymer,namely {[Zn2（tzba）（dmtrz）（OH）]·3H2O}n（1,H2tzba = 4-（5H-tetrazol）benzoic acid,Hdmtrz = 3,5-dimethyl-lH,l,2,4-triazole）,was hydrothermally synthesized and characterized by single-crystal X-ray diffraction.It crystallizes in monoclinic system,P21/c space group with a = 8.018（11）,b = 21.04（3）,c = 11.069（14） A,β=91.26（3）°,V= 1867（4） A^3,Z = 4,Dc = 1.729 g/cm^3,F（000） = 984,μ= 2.614 mm^（-1）,R（F^2 〉 2σ（F^2）） =0.0612 and wR（F^2） = 0.1533.Topological analysis reveals that compound 1 is a（3,5）-connected structure with a Schlafli symbol of（4~2.6）（4~2.6~5.8~3）,which is a rarely observed lhh topology.In addition,the CO2 adsorption performance and luminescent property of 1 have also been studied.
