The developed 1Cr18Ni9Ti austenitic stainless steel containing 1.63 wt.%B have been characterized by X-ray diffraction(XRD),electron probe microanalyzer(EPMA),optical microscopy(OM),scanning electron microscopy(SEM),e...The developed 1Cr18Ni9Ti austenitic stainless steel containing 1.63 wt.%B have been characterized by X-ray diffraction(XRD),electron probe microanalyzer(EPMA),optical microscopy(OM),scanning electron microscopy(SEM),energy dispersive X-ray spectroscopy(EDS)and Vickers microhardness measurement.The microstructural evolution and property of high boron stainless steel after solution treatment at the temperature of 1050℃are also investigated.The results show that the main compositions of borides are Fe,Cr and B,and with small amount of Ni,Mn and C elements.Silicon is insoluble in the borides.The hardness of borides is over 1,500 HV.It has been found that borides do not decompose during solution treatment,but part of borides dissolves into the matrix. The effect of increasing the solubility of boron element in the austenitic matrix favours the hardness enhancement by 8.54%.High boron stainless steel has excellent wear resistance in corrosive environment.Lifetime of transfer pipe made of high boron-containing stainless steel is 1.5-1.8 times longer than that of boron-free 1Cr18Ni9Ti stainless steel.展开更多
A series of single bcc,bcc plus fcc duplex and single fcc microcrystalline coatings of 1Cr18Ni9Ti stainless steel were prepared by using sputtering technique.The resistance against pitting corrosion was studied by mea...A series of single bcc,bcc plus fcc duplex and single fcc microcrystalline coatings of 1Cr18Ni9Ti stainless steel were prepared by using sputtering technique.The resistance against pitting corrosion was studied by measurements of pitting corrosion potentials and electrochemical noise during initiation of corrosion pits.The results show that the sputtered coatings with single bcc phase or single fcc structure are more resistant to pitting corrosion than those with bcc plus fcc duplex phase structure.展开更多
The HIP diffusion bonding of P/M titanium alloy Ti-6Al-4V and stainless steel 1Cr18Ni9Ti using pure Ni as intermediate layer was studied. Bonding joint with complex bonding interface was obtained by HIPing pre-alloyed...The HIP diffusion bonding of P/M titanium alloy Ti-6Al-4V and stainless steel 1Cr18Ni9Ti using pure Ni as intermediate layer was studied. Bonding joint with complex bonding interface was obtained by HIPing pre-alloyed Ti-6Al-4V powders and stainless steel 1Cr18Ni9Ti in a vacuum canning. The joint strengths were examined and the characteristics of bonding joint were observed. The result shows that the maximized strength of HIP diffusion bonding between P/M titanium alloy Ti-6Al-4V and stainless steel 1Cr18Ni9Ti can be up to 388 MPa and the microstructure of bonding joint is acceptable.展开更多
文摘The developed 1Cr18Ni9Ti austenitic stainless steel containing 1.63 wt.%B have been characterized by X-ray diffraction(XRD),electron probe microanalyzer(EPMA),optical microscopy(OM),scanning electron microscopy(SEM),energy dispersive X-ray spectroscopy(EDS)and Vickers microhardness measurement.The microstructural evolution and property of high boron stainless steel after solution treatment at the temperature of 1050℃are also investigated.The results show that the main compositions of borides are Fe,Cr and B,and with small amount of Ni,Mn and C elements.Silicon is insoluble in the borides.The hardness of borides is over 1,500 HV.It has been found that borides do not decompose during solution treatment,but part of borides dissolves into the matrix. The effect of increasing the solubility of boron element in the austenitic matrix favours the hardness enhancement by 8.54%.High boron stainless steel has excellent wear resistance in corrosive environment.Lifetime of transfer pipe made of high boron-containing stainless steel is 1.5-1.8 times longer than that of boron-free 1Cr18Ni9Ti stainless steel.
文摘A series of single bcc,bcc plus fcc duplex and single fcc microcrystalline coatings of 1Cr18Ni9Ti stainless steel were prepared by using sputtering technique.The resistance against pitting corrosion was studied by measurements of pitting corrosion potentials and electrochemical noise during initiation of corrosion pits.The results show that the sputtered coatings with single bcc phase or single fcc structure are more resistant to pitting corrosion than those with bcc plus fcc duplex phase structure.
基金Projects (51312010310) supported by the General Armament Department of Chinese PLA
文摘The HIP diffusion bonding of P/M titanium alloy Ti-6Al-4V and stainless steel 1Cr18Ni9Ti using pure Ni as intermediate layer was studied. Bonding joint with complex bonding interface was obtained by HIPing pre-alloyed Ti-6Al-4V powders and stainless steel 1Cr18Ni9Ti in a vacuum canning. The joint strengths were examined and the characteristics of bonding joint were observed. The result shows that the maximized strength of HIP diffusion bonding between P/M titanium alloy Ti-6Al-4V and stainless steel 1Cr18Ni9Ti can be up to 388 MPa and the microstructure of bonding joint is acceptable.
