一种基于三角数分解的可配置2-D卷积器优化方法

多尺寸2-D卷积通过特征提取在检测、分类等计算机视觉任务中发挥着重要作用。然而,目前缺少一种高效的可配置2-D卷积器设计方法,这限制了卷积神经网络(CNN)模型在边缘端的部署和应用。该文基于乘法管理以及奇平方数的三角数分解方法,提出一种高性能、高适应性的卷积核尺寸可配置的2-D卷积器。所提2-D卷积器包含一定数量的处理单元(PE)以及相应的控制单元,前者负责运算任务,后者负责管理乘法运算的组合,二者结合以实现不同尺寸的卷积。具体地,首先根据应用场景确定一个奇数列表,列表中为2-D卷积器所支持的尺寸,并利用三角数分解得到对应的三角数列表;其次,根据三角数列表和计算需求,确定PE的总数量;最后,基于以小凑大的方法,确定PE的互连方式,完成电路设计。该可配置2-D卷积器通过Verilog硬件描述语言(HDL)设计实现,由Vivado 2 022.2在XCZU7EG板卡上进行仿真和分析。实验结果表明,相比同类方法,该文所提可配置2-D卷积器,乘法资源利用率得到显著提升,由20%~50%提升至89%,并以514个逻辑单元实现1 500 MB/s的吞吐率,具有广泛的适用性。

基于二萘并[2,3-B∶2′,3′-D]呋喃基团的高效窄发射蓝光OLED器件

高效率窄光谱蓝色有机电致发光器件(OLED)是柔性显示领域的研究重点之一。本文以二萘并[2,3-B∶2′,3′-D]呋喃为弱电子受体、N-(4-联苯基)-1-萘胺作为电子给体设计合成了一种D-A-D型蓝光分子DPF-NA,其在正己烷溶液中的发射峰位于441 nm。理论计算与光物理测试结果显示DPF-NA具有杂化局域电荷转移激发态(HLCT)特性,兼具局域态(LE)高发光效率与电荷转移态(CT)高激子利用率特征,在二氯甲烷溶液中的光致发光量子效率(PLQY)为81.2%。基于质量分数3%DPF-NA掺杂浓度的OLED器件电致发光(EL)峰位于455 nm,半峰宽(FWHM)仅为26 nm,CIE(x,y)坐标为(0.14,0.08),最大外量子效率(EQEmax)为6.76%。

New 4-imino-4H-Chromeno[2,3-d]Pyrimidin-3(5H)-Amine: Synthesis, Cytotoxic Effects on Tumoral Cell Lines and in Silico ADMET Properties

The synthesis of new 4-imino-4H-chromeno[2,3-d]pyrimidin-3(5H)-amine in four steps including one step under microwave dielectric heating is reported. The structural identity of the synthesized compounds was established according to their spectroscopic analysis, such as FT-IR, NMR and mass spectroscopy. These new compounds were tested for their antiproliferative activities on seven representative human tumoral cell lines (Huh7 D12, Caco2, MDA-MB231, MDA-MB468, HCT116, PC3 and MCF7) and also on fibroblasts. Among them, only the compounds 6c showed micromolar cytotoxic activity on tumor cell lines (1.8 50 50 > 25 μM). Finally, in silico ADMET studies ware performed to investigate the possibility of using of the identified compound 6c as potential anti-tumor compound.

2-D Modeling and Calculations of Stratospheric Ozone and Influences of Convection, Diffusion, and Time

An engineering system approach of 2-D cylindrical model of transient mass balance calculations of ozone and other concerned chemicals along with fourteen photolysis, ozone-generating and ozone-depleting chemical reaction equations was developed, validated, and used for studying the ozone concentrations, distribution and peak of the layer, ozone depletion and total ozone abundance in the stratosphere. The calculated ozone concentrations and profile at both the Equator and a 60˚N location were found to follow closely with the measured data. The calculated average ozone concentration was within 1% of the measured average, and the deviation of ozone profiles was within 14%. The monthly evolution of stratospheric ozone concentrations and distribution above the Equator was studied with results discussed in details. The influences of slow air movement in both altitudinal and radial directions on ozone concentrations and profile in the stratosphere were explored and discussed. Parametric studies of the influences of gas diffusivities of ozone DO3 and active atomic oxygen DO on ozone concentrations and distributions were also studied and delineated. Having both influences through physical diffusion and chemical reactions, the diffusivity (and diffusion) of atomic oxygen DO was found to be more sensitive and important than that of ozone DO3 on ozone concentrations and distribution. The 2-D ozone model present in this paper for stratospheric ozone and its layer and depletion is shown to be robust, convenient, efficient, and executable for analyzing the complex ozone phenomena in the stratosphere. .

Microstructure Analysis of 4-Step Three-Dimensional Braided Composite

The yarn architecture of 3-D braided composites products by the four-step 1×1 braiding technique has been studied by means of a control volume method in conjunction with experimental investigation and a numerical method, respectively. An ellipse assumption for the cross-section of yarn was proposed in this analysis method with considering the yarn size and yarn-packing factor. Two types of local unit cell structures were identified for 4-step braided composites by considering the nature of the braiding processes and by observing the sample cross-sections. The relationship between the braiding procedure and the properties for 3-D braided structural shapes was established. This method provides the basis for analyzing stiffness and strength of 3-D braided composites.

Filling Simulation of Three-dimension Braided Composite in Resin Transfer Molding

This paper measured permeability of three-dimension braided preform by radial technology. The results show that principal permeability tensor coincided with their braiding axial direction. The software of one dimensional flow filling mold was designed using Visual C++ language. Filling time is predicted and validated. The result showed that the filling time of the mold centerline agrees with the prediction value. The filling time of the mould edge is shorter than that of the prediction. An actual plate of 3D braided preform/ modified polyarylacetylene composite is produced according to prediction value and validation analysis.

Void Morphology in 3-D Braided Preform/phenolic Composites

Improved Resin Transfer Molding (RTM) technology and equipment were established.Void content and morphology of the 3-D braided preform/phenolic composite were investigated using different RTM processes.The results showed that void content of the vacuum and compression co-assisted RTM process was the lowest.Void morphologies of the specimen cross-section were analyzed with metallographic microscope.In traditional RTM process,the crack of cross-section was in evidence.In vacuum assisted RTM process,the void shape was divided into three categories:irregular crack,triangle,rotundity and ellipse.The most voids distributed in resin rich areas and were observed as large void based on equivalent diameter.In compression assisted RTM,vacuum and compression co-assisted RTM process,the polygonal voids mostly existed inter tows.Void size was mainly intermediate and small based equivalent diameter separately.

一种高速2-D滑动FFT的设计实现

文章介绍了采用2-D快速傅里叶变换(fast Fourier transform,FFT)算法的滑动窗FFT的基本特性原理和硬件实现过程,完成了窗长256点、步长16点的2-D滑动窗FFT的专用集成电路(application specific integrated circuit,ASIC)设计。传统FFT算法受序列完整性的制约,时滞较大,无法满足某些高实时性信号分析领域的处理速度要求。该文采用滑动FFT算法,克服了传统FFT对序列完整性的依赖,设计的滑动FFT处理器使用2-D FFT压缩新序列计算时间,以基16蝶形运算器为核心,采用系数复用和高基Booth方法优化系数编码技术压缩乘法器的数量,减少电路面积。所设计的2-D滑动FFT完成单次滑动窗长的计算时间比传统算法节约了16.1%,变换结果与MATLAB的运算结果相比,信噪比(signal-to-noise ratio,SNR)大于130 dB。在TSMC 28 nm的工艺下,工作主频为600 MHz,面积为1980μm×2060μm。

2-D distributed pose estimation of multi-agent systems using bearing measurements

This article studies distributed pose(orientation and position)estimation of leader–follower multi-agent systems over𝜅-layer graphs in 2-D plane.Only the leaders have access to their orientations and positions,while the followers can measure the relative bearings or(angular and linear)velocities in their unknown local coordinate frames.For the orientation estimation,the local relative bearings are used to obtain the relative orientations among the agents,based on which a distributed orientation estimation algorithm is proposed for each follower to estimate its orientation.For the position estimation,the local relative bearings are used to obtain the position constraints among the agents,and a distributed position estimation algorithm is proposed for each follower to estimate its position by solving its position constraints.Both the orientation and position estimation errors converge to zero asymptotically.A simulation example is given to verify the theoretical results.

具有执行器饱和的切换2-D系统事件触发控制

针对具有执行器饱和的切换2-D连续离散系统,提出了一种基于多Lyapunov函数法的事件触发控制方案;为了减少通信资源浪费和执行器的损耗,提出了一种事件触发机制;该触发机制考虑了执行器饱和特性,只有当执行器未饱和,且满足事件触发条件时,控制器才会更新;利用凸组合技术和多Lyapunov函数法,提出了一种状态依赖的切换信号与状态反馈控制器的设计方法,并对闭环系统的指数稳定性进行了分析,利用线性矩阵不等式技术导出了控制器增益矩阵存在的充分条件;利用Darboux方程的仿真算例验证了所提出的事件触发控制方案的有效性,仿真结果表明了在所设计的控制方案下,闭环系统的状态是指数收敛的,同时还能减少通信资源的浪费。

“探究2,4-D对插枝生根的作用”实验中因变量的确定

“探究2,4-D对插枝生根的作用”是浙科版高中生物学教材选择性必修1教材中的重要实验,实践中一些师生对该实验中的因变量常有疑惑,本文选择常见的碰碰香作为实验材料展开探究。发现2,4-D浓度在2.5×10-4—2.5×10-14g/L浓度范围内,对根的平均长度和根的总长度作用差异不明显,但是对根的数量有显著的差异。该探究可为师生提供一定的参考。

Statistical Model of the 3-D Braided Composites Strength

Based on the statistical model for the tensile statistical strength of unidirectional composite materials and the stress analysis of 3-D braided composites, a new method is proposed to calculate the tensile statistical strength of the 3-D braided compos- ites. With this method, the strength of 3-D braided composites can be calculated with very large accuracy, and the statistical parameters of 3-D braided composites can be determined. The numerical result shows that the tensile statistical strength of 3-D braided composites can be predicted using this method.

Calculations and Sensitivity Analysis of Chlorine-,NO_(x)-,and Bromine-Depleting Cycles of Stratospheric Ozone

This paper presents an engineering system approach using a 2D model of conservation of mass to study the dynamics of ozone and concerned chemical species in the stratosphere.By considering all fourteen photolysis,ozone-generating,and-depleting chemical reactions,the model calculated the transient,spatial changes of ozone under different physical-chemical-radiative conditions.Validation against the measured data demonstrated good accuracy,close match of our model with the observed ozone concentrations at both 20°S and 90°N locations.The deviation in the average concentration was less than 1% and in ozone profiles less than 17%.The impacts of various chlorine-(Cl),nitrogen oxides-(NO_(x)),and bromine-(Br)depleting cycles on ozone concentrations and distribution were investigated.The chlorine catalytic depleting cycle was found to exhibit the most significant impact on ozone dynamics,confirming the key role of chlorine in the problem of ozone depletion.Sensitivity analysis was conducted with levels of 25%,50%,100%,200%,and 400% of the baseline value.The combined cycles(Cl+NO_(x)+Br)showed the most significant influence on ozone behavior.The total ozone abundance above the South Pole could decrease by a small 3%,from 281 DU(Dubson Units)to 273 DU for the 25% level,or by a huge thinning of 60%to 114 DU for the 400% concentration level.When the level of chlorine gases increased beyond 200%,it would cause ozone depletion to a level of ozone hole(below 220 DU).The 2D Ozone Model presented in this paper demonstrates robustness,convenience,efficiency,and executability for analyzing complex ozone phenomena in the stratosphere.

DAMAGE MECHANISM ANALYSIS OF 2D 1×1 BRAIDED COMPOSITES UNDER UNIDIRECTIONAL TENSION

Coupling with the periodical displacement boundary condition,a representative volume element(RVE) model is established to simulate the progressive damage behavior of 2D1×1 braided composites under unidirectional tension by using the nonlinear finite element method.Tsai-Wu failure criterion with various damage modes and Mises criterion are considered for predicting damage initiation and progression of yarns and matrix.The anisotropic damage model for yarns and the isotropic damage model for matrix are used to simulate the microscopic damage propagation of 2D1×1braided composites.Murakami′s damage tensor is adopted to characterize each damage mode.In the simulation process,the damage mechanisms are revealed and the tensile strength of 2D1×1braided composites is predicted from the calculated average stress-average strain curve.Numerical results show good agreement with experimental data,thus the proposed simulation method is verified for damage mechanism analysis of 2D braided composites.

2,4-D丁酯对轮叶马先蒿的防除效果及对草地植被的影响

为有效灭除草地害草轮叶马先蒿,采用2,4-D丁酯在巴音布鲁克高寒草地进行了不同时期不同剂量化学防除试验。结果表明,防除轮叶马先蒿的最佳时期为盛花期;最佳药品用量是0.066 mL/m2;喷施2,4-D丁酯后,草地植被生态环境得到明显改善,轮叶马先蒿被部分或完全灭除,优良牧草垂穗披碱草在草地群落中占据优势地位,同时杂类草新疆假龙胆受到一定的抑制,草地质量明显提高。

三乙基苄基氯化铵催化下水介质中吡喃并[2，3-d]嘧啶衍生物的一步合成

以芳亚甲基丙二腈、1,3-二甲基巴比妥酸为原料,以水为溶剂,在100℃以三乙基苄基氯化铵(TEBAC)为催化剂合成了一系列的吡喃并[2,3-d]嘧啶衍生物,该方法具有反应条件温和,产率良好(78%～90%)和环境友好等优点.产物的结构通过IR,1H NMR和元素分析表征,并进一步通过X射线衍射分析确证.

2,4-D和根瘤菌对烟草类根瘤形成的影响

烟草再生植株在含有 0 .3mg/L 2 ,4 D和 5× 10 8个 /L豌豆根瘤菌的Jensen培养基中 ,可以在其根部形成大量近似半球形和球形的类根瘤 .烟草再生植株的结瘤除受制于 2 ,4 D和根瘤菌的浓度外 ,还与根瘤菌的种类和加入根瘤菌与 2 ,4 D的时期有关 .

检测2,4-D的一次性安培型免疫传感器

2,4-D是广泛使用的除草剂,以2,4-D为检测目标,研究了安培型免疫传感器.首先采用1-乙基-3-(3-二甲基氨丙基)碳二亚胺盐酸盐(EDC)作为交联剂制备2,4-D与BSA以及PLL的偶联物.用结合比1:16的2,4-D与偶联物制备兔抗血清.免疫传感器的制备包括2个步骤,使用丝网印刷工艺制备一次性碳电极,然后通过戊二醛交联在电极表面固定2,4-D与多聚赖氨酸(PLL)的偶联物.待测水样与2,4-D抗血清和HRP酶标二抗进行间接免疫竞争反应.在HRP酶在邻苯二胺和H2O的共同作用下发生酶促反应,检测还原电流以反映2,4-D的浓度.试验了不同浓度抗血清和酶标二抗对检测信号的影响,结果表明,2,4-D的检测下限达到1.69ng/mL,线性区间1.69～30 000ng/mL,适合饮用水中2,4-D的检测要求.

基于特征分解的2-D多边形渐变

二维多边形渐变在二维角色动画、模式匹配、几何造型等领域有着重要的应用.已有的方法大多根据多边形的边长、角度、面积、骨架等几何属性来完成多边形之间的最佳对应和渐变,而忽略了多边形的内在视觉特征.提出了一种基于视觉特征对应的 2-D 多边形渐变方法,该方法把源多边形和目标多边形按照视觉特征进行同构特征分解,得到若干对对应的特征子多边形.在渐变过程中,每个源特征子多边形光滑地过渡到目标特征子多边形.通过引入特征分解点,用户可以灵活和直观地改变特征子多边形,按照预想的效果控制多边形的渐变.实验效果表明,基于特征分解的顶点对应和插值算法不仅可以得到光滑的多边形渐变序列,而且可以实现多特征保留.

超声辐射下水介质中三组分一锅合成吡喃并[2,3-d]嘧啶衍生物

报道了在超声波辐射下,水相中无催化剂下通过芳香醛与丙二腈、巴比妥酸的一锅反应,合成了一系列吡喃并[2,3-d]嘧啶衍生物.在超声波辐射下,不仅饱和芳香醛与丙二腈、巴比妥酸的一锅反应在室温下能高收率地进行,而对于α,β-不饱和醛以及二元醛与丙二腈、巴比妥酸的一锅反应也能在室温下顺利进行,获得较高的收率.产物的结构通过IR,1HNMR和元素分析表征.该方法具有操作简单和环境友好等优点。