Based on the design of the multi-row sprocket with a new tooth profile,a cold semi-precision forging process for manufacturing 5052 aluminum alloy multi-row sprocket was presented.Through simulating the forging proces...Based on the design of the multi-row sprocket with a new tooth profile,a cold semi-precision forging process for manufacturing 5052 aluminum alloy multi-row sprocket was presented.Through simulating the forging process of 5052 aluminum alloy sprocket billet with 3D rigid-viscoplastic FEM,both the distributions of flow velocity field in axial(U_Z),radial(U_R) and circumferential(U_θ) directions and the curves of velocity component in different deformation regions were respectively obtained.By comparison and analysis of the velocity varying curves,the velocity component relation conditions for filling the die cavity were clarified.It shows that when the die cavity is almost fully filled,the circumferential velocity U_θ increases sharply,implying that U_θplays a key role in fully filling the die cavity.展开更多
This paper deals with the mathematical modelling and 3D FEM study of the energy release rate(ERR)in the band crack’s front contained in the orthotropic thick rectangular plate which is stretched or compressed initial...This paper deals with the mathematical modelling and 3D FEM study of the energy release rate(ERR)in the band crack’s front contained in the orthotropic thick rectangular plate which is stretched or compressed initially before the loading of the crack's edge planes.The initial stretching or compressing of the plate causes uniformly distributed normal stress to appear acting in the direction which is parallel to the plane on which the band crack is located.After the appearance of the initial stress in the plate it is assumed that the crack's edge planes are loaded with additional uniformly distributed normal forces and the ERR caused with this additional loading is studied.The corresponding boundary value problem is formulated within the scope of the so-called 3D linearized theory of elasticity which allows the initial stress on the values of the ERR to be taken into consideration.Numerical results on the influence of the initial stress,anisotropy properties of the plate material,the crack’s length and its distance from the face planes of the plate on the values of the ERR,are presented and discussed.In particular,it is established that for the relatively greater length of the crack’s band,the initial stretching of the plate causes a decrease,but the initial compression causes an increase in the values of the ERR.展开更多
The pile-supported subgrade has been widely used in high-speed railway construction in China.To investigate the ground vibrations of such composite foundation subjected to moving loads induced by high-speed trains(HST...The pile-supported subgrade has been widely used in high-speed railway construction in China.To investigate the ground vibrations of such composite foundation subjected to moving loads induced by high-speed trains(HSTs),three-dimensional(3D)finite element method(FEM)models involving the pile,pile cap and cushion are established.Validation of the proposed model is conducted through comparison of model predictions with the field measurements.On this basis,ground vibrations generated by HSTs under different train speeds as well as the ground vibration attenuation with the distance away from the track centerline are investigated.In addition,the effects of piles and pile elastic modulus on ground vibrations are well studied.Results show that the pile-reinforcement of the subgrade could significantly contribute to the reduction of ground vibrations.In particular,the increase of elastic modulus of pile could lead to consistent reduction of ground vibrations.However,when the pile elastic modulus is beyond 10 GPa,this benefit of pile-reinforcement on vibration isolation can hardly be increased further.展开更多
3-D rigid visco-plastic finite element method (FEM) is used in the analysisof metal forming processes, including strip and plate rolling, shape rolling, slab edging, specialstrip rolling. The shifted incomplete Choles...3-D rigid visco-plastic finite element method (FEM) is used in the analysisof metal forming processes, including strip and plate rolling, shape rolling, slab edging, specialstrip rolling. The shifted incomplete Cholesky decomposition of the stiffness matrix with thesolution of the equations for velocity increment by the conjugate gradient method is combined. Thistechnique, termed the shifted ICCG method, is then employed to solve the slab edging problem. Theperformance of this algorithm in terms of the number of iterations, friction variation, shiftedparameter psi and the results of simulation for processing parameters are analysed. Numerical testsand application of this technique verify the efficiency and stability of the shifted ICCG method inthe analysis of slab edging.展开更多
In order to explore the mineral resources buried in sea mud,it is necessary to use seabed resistivity measuring equipment,which works closer to the sediments than ordinary ship-based geophysical measuring equipment. B...In order to explore the mineral resources buried in sea mud,it is necessary to use seabed resistivity measuring equipment,which works closer to the sediments than ordinary ship-based geophysical measuring equipment. Because of the harsh environment of seafloor,high pressure and highly conductive seawater,marine magnetotelluric method developed slowly. The sea floor environment is similar to the environment of logging, According to the design of dual lateral logging equipment,a new equipment for seafloor electrical resistivity measurement is designed. Four 3D FEM models that contain resistivity abnormal targets are built to test the ability of this equipment to locate different shape of shallow buried resistivity abnormal targets in sea mud. The authors propose the method to correct the response curve while the bottom surface of this equipment is suspended or not parallel to the seafloor. The resistivity of targets can be calculated accurately.展开更多
Backward spinning is analyzed by 3D rigid-plastic FEM.A 3D mechanical model for backward spinning is presented. The distributions are obtained of strain一rate and stress in the con- tact area of the roller a...Backward spinning is analyzed by 3D rigid-plastic FEM.A 3D mechanical model for backward spinning is presented. The distributions are obtained of strain一rate and stress in the con- tact area of the roller and its adjacent area.The results can well intemret the principle of defonnation of backward spinning. The relationship between the roller angle and three components ofspinning force is found out, and the optimum roller angle, when the general spinning foree gets to the minimum value, is calculated. The distributions of defonnation area obtained by FEM agree with the experimental result well.展开更多
Springback is one of important factors influencing the forming quality of numerical control （NC） bending of thin-walled tube. In this paper, a numerical-analytic method for springback angle prediction of the process...Springback is one of important factors influencing the forming quality of numerical control （NC） bending of thin-walled tube. In this paper, a numerical-analytic method for springback angle prediction of the process was put forward. The method is based on springback angle model derived using analytic method and simulation results from three-dimensional （3D） rigid-plastic finite element method （FEM）. The method is validated through comparison with experimental results. The features of the method are as follows： （1） The method is high in efficiency because it combines advantages of rigid-plastic FEM and analytic method. （2） The method is satisfactory in accuracy, since the field variables used in the model is resulting from 3D rigid-plastic FEM solution, and the effects both of axial force and strain neutral axis shift have been included. （3） Research on multi-factor effects can be carried out using the method due to its advantage inheriting from rigid-plastic FEM. The method described here is also of general significance to other bending processes.展开更多
The extended Kantorovich method is employed to study the local stress concentrations at the vicinity of free edges in symmetrically layered composite laminates subjected to uniaxial tensile load upon polynomial stress...The extended Kantorovich method is employed to study the local stress concentrations at the vicinity of free edges in symmetrically layered composite laminates subjected to uniaxial tensile load upon polynomial stress functions. The stress fields are initially assumed by means of the Lekhnitskii stress functions under the plane strain state. Applying the principle of complementary virtual work,the coupled ordinary differential equations are obtained in which the solutions can be obtained by solving a generalized eigenvalue problem. Then an iterative procedure is established to achieve convergent stress distributions. It should be noted that the stress function based extended Kantorovich method can satisfy both the traction-free and free edge stress boundary conditions during the iterative processes. The stress components near the free edges and in the interior regions are calculated and compared with those obtained results by finite element method（FEM）. The convergent stresses have good agreements with those results obtained by three dimensional（3D） FEM. For generality, various layup configurations are considered for the numerical analysis. The results show that the proposed polynomial stress function based extended Kantorovich method is accurate and efficient in predicting the local stresses in composite laminates and computationally much more efficient than the 3D FEM.展开更多
Forced and natural vibrations of a rectangular pre-stressed orthotropic compositeplate containing two neighboring cylindrical cavities whose cross sections are rectangularwith rounded-off corners are investigated nume...Forced and natural vibrations of a rectangular pre-stressed orthotropic compositeplate containing two neighboring cylindrical cavities whose cross sections are rectangularwith rounded-off corners are investigated numerically. It is assumed that all the end surfacesof the rectangular pre-stressed composite plate are simply supported and subjected to auniformly distributed normal time-harmonic force on the upper face plane. The consideredproblem is formulated within the Three-Dimensional Linearized Theory of Elastic Waves inInitially Stressed Bodies (TDLTEWISB). The influence of mechanical and geometricalparameters as well as the initial stresses and the effect of cylindrical cavities on the dynamicalcharacteristics of the rectangular orthotropic composite plate are analyzed and discussed.展开更多
The blade precision forging process is a forming process with high temperature and large plastic deformation. Interaction of deformation and heat conduction leads to large uneven distribution of temperature. The uneve...The blade precision forging process is a forming process with high temperature and large plastic deformation. Interaction of deformation and heat conduction leads to large uneven distribution of temperature. The unevenness of temperature distribution has a great effect on mechanical properties and the microstracture of materials. So it is necessary to consider the influence of temperature on the precision forging process of blades. Taking a blade with a tenon into consideration, a 3D mechanical model in precision forging is built up. The distribution laws of temperature field and the influence of the temperature on the equivalem stress in the process are obtained by using 3-D coupled thermo-mechanical FEM code developed by the authors Theresuits obtained illustrate that the influence of the temperature field on the blade forging process is considerable. The achievements of predicting microstructure and mechanical properties for forged blades is significant.展开更多
This study explored the seismic response of a house supporting base sides with a polymeric displacement control material and by magnetically levitating the foundation base. In this paper, we explore the possibility an...This study explored the seismic response of a house supporting base sides with a polymeric displacement control material and by magnetically levitating the foundation base. In this paper, we explore the possibility and efficacy of a seismic-isolated detached house as described above from both a shaking table experiment of model and three-dimensional finite element analysis. The seismic-isolated model showed stable response and its acceleration response was significantly reduced compared to the base-fixed model in the shaking table test. Three-dimensional finite element analysis was possible to simulate the experimental results. In the seismic response analysis of a full-scale detached house, the seismic-isolated model showed response reduction and its residual displacement was smaller than that of the sliding-base isolation model.展开更多
Backward erosion piping is an important failure mechanism for cohesive water retaining structures which are founded on a sandy aquifer. At present, the prediction models for safety assessment are often based on 2D ass...Backward erosion piping is an important failure mechanism for cohesive water retaining structures which are founded on a sandy aquifer. At present, the prediction models for safety assessment are often based on 2D assumptions. In this work, a 3D numerical approach of the groundwater flow leading to the erosion mechanism of backward erosion piping is presented and discussed. Comparison of the 2D and 3D numerical results explicitly demonstrates the inherent 3D nature of the piping phenomenon. In addition, the influence of the seepage length is investigated and discussed for both piping initiation and piping progression. The results clearly indicate the superiority of the presented 3D numerical model compared to the established 2D approach. Moreover, the 3D numerical results enable a better understanding of the complex physical mechanism involved in backward erosion piping and thus can lead to a significant improvement in the safety assessment of water retaining structures.展开更多
基金Projects(51175363,51274149)supported by the National Natural Science Foundation of China
文摘Based on the design of the multi-row sprocket with a new tooth profile,a cold semi-precision forging process for manufacturing 5052 aluminum alloy multi-row sprocket was presented.Through simulating the forging process of 5052 aluminum alloy sprocket billet with 3D rigid-viscoplastic FEM,both the distributions of flow velocity field in axial(U_Z),radial(U_R) and circumferential(U_θ) directions and the curves of velocity component in different deformation regions were respectively obtained.By comparison and analysis of the velocity varying curves,the velocity component relation conditions for filling the die cavity were clarified.It shows that when the die cavity is almost fully filled,the circumferential velocity U_θ increases sharply,implying that U_θplays a key role in fully filling the die cavity.
文摘This paper deals with the mathematical modelling and 3D FEM study of the energy release rate(ERR)in the band crack’s front contained in the orthotropic thick rectangular plate which is stretched or compressed initially before the loading of the crack's edge planes.The initial stretching or compressing of the plate causes uniformly distributed normal stress to appear acting in the direction which is parallel to the plane on which the band crack is located.After the appearance of the initial stress in the plate it is assumed that the crack's edge planes are loaded with additional uniformly distributed normal forces and the ERR caused with this additional loading is studied.The corresponding boundary value problem is formulated within the scope of the so-called 3D linearized theory of elasticity which allows the initial stress on the values of the ERR to be taken into consideration.Numerical results on the influence of the initial stress,anisotropy properties of the plate material,the crack’s length and its distance from the face planes of the plate on the values of the ERR,are presented and discussed.In particular,it is established that for the relatively greater length of the crack’s band,the initial stretching of the plate causes a decrease,but the initial compression causes an increase in the values of the ERR.
基金Project(51978510)supported by the National Natural Science Foundation of China。
文摘The pile-supported subgrade has been widely used in high-speed railway construction in China.To investigate the ground vibrations of such composite foundation subjected to moving loads induced by high-speed trains(HSTs),three-dimensional(3D)finite element method(FEM)models involving the pile,pile cap and cushion are established.Validation of the proposed model is conducted through comparison of model predictions with the field measurements.On this basis,ground vibrations generated by HSTs under different train speeds as well as the ground vibration attenuation with the distance away from the track centerline are investigated.In addition,the effects of piles and pile elastic modulus on ground vibrations are well studied.Results show that the pile-reinforcement of the subgrade could significantly contribute to the reduction of ground vibrations.In particular,the increase of elastic modulus of pile could lead to consistent reduction of ground vibrations.However,when the pile elastic modulus is beyond 10 GPa,this benefit of pile-reinforcement on vibration isolation can hardly be increased further.
基金supported by Huo Yingdong Young Teachers Foundation,Ministry of State Education of ChinaNational Natural Science Foundation of China(No.59904003).
文摘3-D rigid visco-plastic finite element method (FEM) is used in the analysisof metal forming processes, including strip and plate rolling, shape rolling, slab edging, specialstrip rolling. The shifted incomplete Cholesky decomposition of the stiffness matrix with thesolution of the equations for velocity increment by the conjugate gradient method is combined. Thistechnique, termed the shifted ICCG method, is then employed to solve the slab edging problem. Theperformance of this algorithm in terms of the number of iterations, friction variation, shiftedparameter psi and the results of simulation for processing parameters are analysed. Numerical testsand application of this technique verify the efficiency and stability of the shifted ICCG method inthe analysis of slab edging.
文摘In order to explore the mineral resources buried in sea mud,it is necessary to use seabed resistivity measuring equipment,which works closer to the sediments than ordinary ship-based geophysical measuring equipment. Because of the harsh environment of seafloor,high pressure and highly conductive seawater,marine magnetotelluric method developed slowly. The sea floor environment is similar to the environment of logging, According to the design of dual lateral logging equipment,a new equipment for seafloor electrical resistivity measurement is designed. Four 3D FEM models that contain resistivity abnormal targets are built to test the ability of this equipment to locate different shape of shallow buried resistivity abnormal targets in sea mud. The authors propose the method to correct the response curve while the bottom surface of this equipment is suspended or not parallel to the seafloor. The resistivity of targets can be calculated accurately.
文摘Backward spinning is analyzed by 3D rigid-plastic FEM.A 3D mechanical model for backward spinning is presented. The distributions are obtained of strain一rate and stress in the con- tact area of the roller and its adjacent area.The results can well intemret the principle of defonnation of backward spinning. The relationship between the roller angle and three components ofspinning force is found out, and the optimum roller angle, when the general spinning foree gets to the minimum value, is calculated. The distributions of defonnation area obtained by FEM agree with the experimental result well.
基金This work was supported by the National Natural Science Foundation of China for Distinguished Young Scholars （Grant No. 50225518）the Teaching and Research Award Program for 0utstanding Young Teachers in Higher Education Institution of M0E, PRCthe Aeronautical Science Foundation of China （Grant No. 04H53057）.
文摘Springback is one of important factors influencing the forming quality of numerical control （NC） bending of thin-walled tube. In this paper, a numerical-analytic method for springback angle prediction of the process was put forward. The method is based on springback angle model derived using analytic method and simulation results from three-dimensional （3D） rigid-plastic finite element method （FEM）. The method is validated through comparison with experimental results. The features of the method are as follows： （1） The method is high in efficiency because it combines advantages of rigid-plastic FEM and analytic method. （2） The method is satisfactory in accuracy, since the field variables used in the model is resulting from 3D rigid-plastic FEM solution, and the effects both of axial force and strain neutral axis shift have been included. （3） Research on multi-factor effects can be carried out using the method due to its advantage inheriting from rigid-plastic FEM. The method described here is also of general significance to other bending processes.
基金supported by the National Natural Science Foundation of China (Grants 11372145, 11372146, and 11272161)the State Key Laboratory of Mechanics and Control of Mechanical Structures (Nanjing University of Aeronautics and astronautics) (Grant MCMS-0516Y01)+1 种基金Zhejiang Provincial Top Key Discipline of Mechanics Open Foundation (Grant xklx1601)the K. C. Wong Magna Fund through Ningbo University
文摘The extended Kantorovich method is employed to study the local stress concentrations at the vicinity of free edges in symmetrically layered composite laminates subjected to uniaxial tensile load upon polynomial stress functions. The stress fields are initially assumed by means of the Lekhnitskii stress functions under the plane strain state. Applying the principle of complementary virtual work,the coupled ordinary differential equations are obtained in which the solutions can be obtained by solving a generalized eigenvalue problem. Then an iterative procedure is established to achieve convergent stress distributions. It should be noted that the stress function based extended Kantorovich method can satisfy both the traction-free and free edge stress boundary conditions during the iterative processes. The stress components near the free edges and in the interior regions are calculated and compared with those obtained results by finite element method（FEM）. The convergent stresses have good agreements with those results obtained by three dimensional（3D） FEM. For generality, various layup configurations are considered for the numerical analysis. The results show that the proposed polynomial stress function based extended Kantorovich method is accurate and efficient in predicting the local stresses in composite laminates and computationally much more efficient than the 3D FEM.
文摘Forced and natural vibrations of a rectangular pre-stressed orthotropic compositeplate containing two neighboring cylindrical cavities whose cross sections are rectangularwith rounded-off corners are investigated numerically. It is assumed that all the end surfacesof the rectangular pre-stressed composite plate are simply supported and subjected to auniformly distributed normal time-harmonic force on the upper face plane. The consideredproblem is formulated within the Three-Dimensional Linearized Theory of Elastic Waves inInitially Stressed Bodies (TDLTEWISB). The influence of mechanical and geometricalparameters as well as the initial stresses and the effect of cylindrical cavities on the dynamicalcharacteristics of the rectangular orthotropic composite plate are analyzed and discussed.
基金supported by the Aeronautical Science Foundation of China(No.02H53061)the National Science Found of China for Distinguished Young Scholar(No.50225518)the Shaan'xi Provincial Natural Science Foundation of China(No.2001CS0401)
文摘The blade precision forging process is a forming process with high temperature and large plastic deformation. Interaction of deformation and heat conduction leads to large uneven distribution of temperature. The unevenness of temperature distribution has a great effect on mechanical properties and the microstracture of materials. So it is necessary to consider the influence of temperature on the precision forging process of blades. Taking a blade with a tenon into consideration, a 3D mechanical model in precision forging is built up. The distribution laws of temperature field and the influence of the temperature on the equivalem stress in the process are obtained by using 3-D coupled thermo-mechanical FEM code developed by the authors Theresuits obtained illustrate that the influence of the temperature field on the blade forging process is considerable. The achievements of predicting microstructure and mechanical properties for forged blades is significant.
文摘This study explored the seismic response of a house supporting base sides with a polymeric displacement control material and by magnetically levitating the foundation base. In this paper, we explore the possibility and efficacy of a seismic-isolated detached house as described above from both a shaking table experiment of model and three-dimensional finite element analysis. The seismic-isolated model showed stable response and its acceleration response was significantly reduced compared to the base-fixed model in the shaking table test. Three-dimensional finite element analysis was possible to simulate the experimental results. In the seismic response analysis of a full-scale detached house, the seismic-isolated model showed response reduction and its residual displacement was smaller than that of the sliding-base isolation model.
文摘Backward erosion piping is an important failure mechanism for cohesive water retaining structures which are founded on a sandy aquifer. At present, the prediction models for safety assessment are often based on 2D assumptions. In this work, a 3D numerical approach of the groundwater flow leading to the erosion mechanism of backward erosion piping is presented and discussed. Comparison of the 2D and 3D numerical results explicitly demonstrates the inherent 3D nature of the piping phenomenon. In addition, the influence of the seepage length is investigated and discussed for both piping initiation and piping progression. The results clearly indicate the superiority of the presented 3D numerical model compared to the established 2D approach. Moreover, the 3D numerical results enable a better understanding of the complex physical mechanism involved in backward erosion piping and thus can lead to a significant improvement in the safety assessment of water retaining structures.
