3-D Simulation of FINFET

An SOI MOSFET with FINFET structure is simulated using a 3 D simulator. I V characteristics and sub threshold characteristics,as well as the short channel effect(SCE) are carefully investigated.SCE can be well controlled by reducing fin height.Good performance can be achieved with thin height,so fin height is considered as a key parameter in device design.Simulation results show that FINFETs present performance superior to conventional single gate devices.

3-D Simulation Study on Seismic Response of Bridge Piles in Landslide

The anti-slide support structure is widely used in the anti-seismic reinforcement of bridge foundations,but related experimental research was processing slowly. Based on the prototype of the Jiuzhaigou bridge at the Chengdu-Lanzhou Railway,a 3-D simulation model was established on the basis of the shaking table model test,and the rationality of the dynamic analysis model was verified by indicators such as the bending moment of the bridge piles,peak soil pressure,and PGA amplification factors. The results show that the inertia force of the bridge pier has an important influence on the deformation of the pile foundation. The bending moment and shearing force are larger in lateral bridge piles,and the maximum value is near the pile top. The PGA amplification factor is stronger in the back of the rear anti-slide piles and so is it in front of the bridge pier,and the soil is prone to slip and damage. The bedrock is rigid and the dynamic response is maintained at a low level. The anti-slide piles in the rear row play a major role in the anti-seismic reinforcement design,and the anti-slide piles in the front row can be used as an auxiliary support structure.

Geant4 simulation of fast-electron bremsstrahlung imaging at the HL-3 tokamak

To further research on high-parameter plasma,we plan to develop a two-dimensional hard X-ray(HXR)imaging system at the HL-3 tokamak to measure HXRs with energies ranging from 20 to 300 keV.The application of an array-structured detector ensures that this system can measure HXR-radiation spectra from the entire plasma cross section.Therefore,it is suitable for the study of fast-electron physics,such as radio-frequency wave current drives,fast electrons driving instabilities,and plasma disruptions in fusion research.In this study,we develop a simulation for calculating fast-electron bremsstrahlung in the HL-3 tokamak based on the Monte Carlo simulation code Geant4,in which the plasma geometry and forward scattering of fast-electron bremsstrahlung are considered.The preliminary calculation results indicate that the HXR energy deposi-tion on the detector is symmetrically distributed,even though the plasma distribution is asymmetric owing to the toroidal effect.These simulation results are helpful in constructing the relationship between the energy deposition on the detector and parameter distribution on the plasma cross section during HL-3 experiments.This is beneficial for the reconstruction of the fast-electron-distribution function and for optimizing the design of the HXR-imaging system.

Hydrogen-bond mediated and concentrate-dependent NaHCO_(3) crystal morphology in NaHCO3–Na2CO3 aqueous solution: Experiments and computer simulations

Adding Na_(2)CO_(3) to the NaHCO_(3) cooling crystallizer, using the common ion effect to promote crystallization and improve product morphology, is a new process recently proposed in the literature. However, the mechanism of the impact of Na_(2)CO_(3)on the crystal morphology is still indeterminate. In this work, the crystallization of NaHCO_(3)in water and Na_(2)CO_(3)–NaHCO_(3) aqueous solution was investigated by experiments and molecular dynamics simulations(MD). The crystallization results demonstrate that the morphology of NaHCO_(3) crystal changed gradually from needle-like to flake structure with the addition of Na_(2)CO_(3). The simulation results indicate that the layer docking model and the modified attachment energy formula without considering the roughness of crystal surface can obtain the crystal morphology in agreement with the experimental results, but the lower molecules of the crystal layer have to be fixed during MD. Thermodynamic calculation of the NaHCO_(3) crystallization process verifies that the common ion effect from Na^(+)and the ionization equilibrium transformation from CO_(3)^(2-) jointly promote the precipitation of NaHCO_(3) crystal. The radial distribution function analysis indicates that the oxygen atoms of Na_(2)CO_(3) formed strong hydrogen bonds with the hydrogen atoms of the(0 1 1) face, which weakened the hydration of water molecules at the crystal surface, resulting in a significant change in the attachment energy of this crystal surface. In addition, Na+and CO_(3)^(2-) are more likely to accumulate on the(011) face,resulting in the fastest growth rate on this crystal surface, which eventually leads to a change in crystal morphology from needle-like to flake-like.

(1-3)-β-D葡聚糖联合降钙素原、CD4^(+)T淋巴细胞多指标在艾滋病患者马尔尼菲篮状菌感染早期诊断临床研究

目的探讨(1-3)-β-D葡聚糖联合降钙素原(procalcitonin,PCT)、CD4^(+)T淋巴细胞多指标在艾滋病患者马尔尼菲篮状菌感染早期诊断临床研究。方法回顾性选取我院2020年1月—2022年6月住院的120例艾滋病患者为研究对象。依据实验室结果,将其分为马尔尼菲篮状菌感染确诊组(血或组织液培育养出马尔尼菲篮状菌),简称A组(62例),及马尔尼菲篮状菌感染临床诊断组[根据临床症状、体征、血常规及(1-3)-β-D葡聚糖、PCT、CD4^(+)T淋巴细胞多指标诊断],简称B组(58例)。检测患者(1-3)-β-D葡聚糖、PCT、CD4^(+)T淋巴细胞的表达水平,采用受试者工作特征(receiver-operating characteristic,ROC)曲线下面积(area under the curve,AUC)评估上述指标联合检测对艾滋病患者感染马尔尼菲篮状菌的诊断效能。结果A组的(1-3)-β-D葡聚糖和PCT水平均高于B组,CD4^(+)T淋巴细胞个数低于B组(P<0.05);(1-3)-β-D葡聚糖、PCT、CD4^(+)T淋巴细胞联合检测的AUC为0.933,(1-3)-β-D葡聚糖单独检测的AUC是0.812,PCT单独检测的AUC为0.883,CD4^(+)T淋巴细胞单独检测的AUC是0.810,(1-3)-β-D葡聚糖、PCT和CD4^(+)T淋巴细胞联合检测的AUC皆优于三项单独检测,表明(1-3)-β-D葡聚糖、PCT和CD4^(+)T淋巴细胞联合检测的诊断价值皆优于单一指标诊断,且联合检测的特异度、约登指数分别为92.43%和0.580,均高于三项单独检测。结论(1-3)-β-D葡聚糖联合PCT和CD4^(+)T淋巴细胞多指标对艾滋病马尔尼菲篮状菌感染具有非常高的临床诊断价值,能够帮助医生分析出高危风险患者,及时制定治疗方案,同时也承担预后效果的判断依据,对治疗艾滋病马尔尼菲篮状菌感染具有非常重要的研究价值。

1例RHD-CE(3-7)-D基因重组与RHCE变异型患者的血清学与分子生物学分析

目的 研究分析1例Rh血型弱D、弱cE患者的血清学与分子生物学特征,为该类患者的临床安全输血提供实验依据。方法 采用微柱凝胶卡法对患者红细胞进行ABO、RhDCcEe抗原的鉴定,同时采用试管法进行血型复核,抗人球蛋白卡法筛查不规则抗体;采用PCR-SSP法对RhDCcEe(RhD、RhC、Rhc、RhE、Rhe)基因型进行检测;三代全长测序技术对RHD/RHCE基因序列进行测序分析。结果 微柱凝胶卡法鉴定ABO、RhD、RhCcEe血型抗原的结果为:A抗原(-)、B抗原(-)、RhD(1+)、RhC(4+)、Rhc(1+)、RhE(1+)、Rhe(4+)、对照孔(-);试管法ABO、RhD、RhCcEe抗原鉴定该患者表型为:A抗原(-)、B抗原(-)、RhD(w+)、RhC(4+)、Rhc(w+)、RhE(w+)、Rhe(4+),对照管(-);抗人球蛋白卡法筛查患者不规则抗体阴性;PCR-SSP法血型基因分型RhDCcEe结果:RhD(+)、RhC(+)、Rhc(+)、RhE(+)、Rhe(+);RHD/RHCE基因结果:RHD单倍体1为外显子1-10全缺失,而单倍体2为外显子RHD-CE基因重组融合,且确认其重组类型为RHD-CE(3-7)-D,起点在外显子2(g.20238-20312之间),终点在外显子8(g49184-50480之间),同时RHCE基因第6外显子存在新碱基点突变RHCE*cE(827C>A)。结论RHD-CE(3-7)-D基因重组融合与RHCE*cE(827C>A)新等位基因突变可能引起D、cE血型抗原弱表达,为临床安全输血提供了重要的实验数据支持。

High-Efficiency Photo-Induced Charge Transfer for SERS Sensing in N-Doped 3D-Graphene on Si Heterojunction

Nitrogen-doped three-dimensional graphene(N-doped 3D-graphene)is a graphene derivative with excellent adsorption capacity,large specific surface area,high porosity,and optoelectronic properties.Herein,N-doped 3D-graphene/Si heterojunctions were grown in situ directly on silicon(Si)substrates via plasma-assisted chemical vapor deposition(PACVD),which is promising for surface-enhanced Raman scattering(SERS)substrates candidates.Combined analyses of theoretical simulation,incorporating N atoms in 3D-graphene are beneficial to increase the electronic state density of the system and enhance the charge transfer between the substrate and the target molecules.The enhancement of the optical and electric fields benefits from the stronger light-matter interaction improved by the natural nano-resonator structure of N-doped 3D-graphene.The as-prepared SERS substrates based on N-doped 3D-graphene/Si heterojunctions achieve ultra-low detection for various molecules:10^(-8)M for methylene blue(MB)and 10^(-9)M for crystal violet(CRV)with rhodamine(R6G)of 10^(10)M.In practical detected,10^(-8)M thiram was precisely detected in apple peel extract.The results indicate that N-doped 3D-graphene/Si heterojunctions based-SERS substrates have promising applications in low-concentration molecular detection and food safety.

A Parallel Discrete Event Simulation Engine for the Low-Earth-Orbit Satellite Constellation Networks

Low-Earth-Orbit satellite constellation networks(LEO-SCN)can provide low-cost,largescale,flexible coverage wireless communication services.High dynamics and large topological sizes characterize LEO-SCN.Protocol development and application testing of LEO-SCN are challenging to carry out in a natural environment.Simulation platforms are a more effective means of technology demonstration.Currently available simulators have a single function and limited simulation scale.There needs to be a simulator for full-featured simulation.In this paper,we apply the parallel discrete-event simulation technique to the simulation of LEO-SCN to support large-scale complex system simulation at the packet level.To solve the problem that single-process programs cannot cope with complex simulations containing numerous entities,we propose a parallel mechanism and algorithms LP-NM and LP-YAWNS for synchronization.In the experiment,we use ns-3 to verify the acceleration ratio and efficiency of the above algorithms.The results show that our proposed mechanism can provide parallel simulation engine support for the LEO-SCN.

Parallel computing approach for efficient 3-D X-ray-simulated image reconstruction

Accurate 3-dimensional(3-D)reconstruction technology for nondestructive testing based on digital radiography(DR)is of great importance for alleviating the drawbacks of the existing computed tomography(CT)-based method.The commonly used Monte Carlo simulation method ensures well-performing imaging results for DR.However,for 3-D reconstruction,it is limited by its high time consumption.To solve this problem,this study proposes a parallel computing method to accelerate Monte Carlo simulation for projection images with a parallel interface and a specific DR application.The images are utilized for 3-D reconstruction of the test model.We verify the accuracy of parallel computing for DR and evaluate the performance of two parallel computing modes-multithreaded applications(G4-MT)and message-passing interfaces(G4-MPI)-by assessing parallel speedup and efficiency.This study explores the scalability of the hybrid G4-MPI and G4-MT modes.The results show that the two parallel computing modes can significantly reduce the Monte Carlo simulation time because the parallel speedup increment of Monte Carlo simulations can be considered linear growth,and the parallel efficiency is maintained at a high level.The hybrid mode has strong scalability,as the overall run time of the 180 simulations using 320 threads is 15.35 h with 10 billion particles emitted,and the parallel speedup can be up to 151.36.The 3-D reconstruction of the model is achieved based on the filtered back projection(FBP)algorithm using 180 projection images obtained with the hybrid G4-MPI and G4-MT.The quality of the reconstructed sliced images is satisfactory because the images can reflect the internal structure of the test model.This method is applied to a complex model,and the quality of the reconstructed images is evaluated.

基于二萘并[2,3-B∶2′,3′-D]呋喃基团的高效窄发射蓝光OLED器件

高效率窄光谱蓝色有机电致发光器件(OLED)是柔性显示领域的研究重点之一。本文以二萘并[2,3-B∶2′,3′-D]呋喃为弱电子受体、N-(4-联苯基)-1-萘胺作为电子给体设计合成了一种D-A-D型蓝光分子DPF-NA,其在正己烷溶液中的发射峰位于441 nm。理论计算与光物理测试结果显示DPF-NA具有杂化局域电荷转移激发态(HLCT)特性,兼具局域态(LE)高发光效率与电荷转移态(CT)高激子利用率特征,在二氯甲烷溶液中的光致发光量子效率(PLQY)为81.2%。基于质量分数3%DPF-NA掺杂浓度的OLED器件电致发光(EL)峰位于455 nm,半峰宽(FWHM)仅为26 nm,CIE(x,y)坐标为(0.14,0.08),最大外量子效率(EQEmax)为6.76%。

New 4-imino-4H-Chromeno[2,3-d]Pyrimidin-3(5H)-Amine: Synthesis, Cytotoxic Effects on Tumoral Cell Lines and in Silico ADMET Properties

The synthesis of new 4-imino-4H-chromeno[2,3-d]pyrimidin-3(5H)-amine in four steps including one step under microwave dielectric heating is reported. The structural identity of the synthesized compounds was established according to their spectroscopic analysis, such as FT-IR, NMR and mass spectroscopy. These new compounds were tested for their antiproliferative activities on seven representative human tumoral cell lines (Huh7 D12, Caco2, MDA-MB231, MDA-MB468, HCT116, PC3 and MCF7) and also on fibroblasts. Among them, only the compounds 6c showed micromolar cytotoxic activity on tumor cell lines (1.8 50 50 > 25 μM). Finally, in silico ADMET studies ware performed to investigate the possibility of using of the identified compound 6c as potential anti-tumor compound.

血浆(1-3)-β-D葡聚糖诊断新生儿侵袭性真菌感染的价值

探讨在针对新生儿侵袭性真菌感染的诊断中使用血浆(1-3)-β-D葡聚糖能够产生的诊断效能。方法 选取2021年1月到2022年2月因为侵袭性真菌感染于医院寻求医疗干预的新生儿总共60例作为本次研究的一部分研究对象记为1组;另外选取60例健康婴儿作为2组;统计、对比两组患者的血浆(1-3)-β-D葡聚糖水平、CD4+T淋巴细胞数水平;整理PCR技术针对1组患者诊断结果,将其与血浆(1-3)-β-D葡聚糖诊断侵袭性真菌感染的诊断效能进行对比。结果 研究结果显示1组患者的血浆(1-3)-β-D葡聚糖水平、CD4+T淋巴细胞数水平较之于2组患者存在明显差异,1组患者血浆(1-3)-β-D葡聚糖水平更高,而CD4+T淋巴细胞数水平明显更低;P<0.05。在针对诊断效能的考察上,血浆(1-3)-β-D葡聚糖诊断效能和PCR诊断结果之间在灵敏度、特异度方面差异不大,P>0.05。结论 针对罹患侵袭性真菌感染的新生儿使用血浆(1-3)-β-D葡聚糖进行检查,一定程度上能够确保诊断结果的严谨程度,可使用。

血浆(1,3)-β-D葡聚糖检测在侵袭性真菌感染诊断中的价值分析

研究血浆(1,3)-β-D葡聚糖检测技术(G实验)应用于侵袭性真菌感染(IFI)诊断中的应用价值。方法 选择我院在2023年1月至2024年1月期间收治的100例高危型侵袭型真菌感染患者,应用MB-80微生物快速检测动态系统以及对应的试剂对患者的血浆(1,3)-β-D葡聚糖进行检测,分析真菌培养、G实验和联合检测结果;三种方法的诊断效能;三种方法的ROC曲线。结果 确诊IFI阳性共28例,阴性共72例;联合检测的诊断效能高于真菌培养或者G实验。联合检测面积高于单一检测。结论 在侵袭性真菌感染的诊断中,应用血浆(1,3)-β-D葡聚糖检测,诊断效能良好,在和传统真菌培养技术联合检测下,可进一步提升诊断效能。

Image processing based three-dimensional model reconstruction for cross-platform numerical simulation

Numerical simulation is the most powerful computational and analysis tool for a large variety of engineering and physical problems.For a complex problem relating to multi-field,multi-process and multi-scale,different computing tools have to be developed so as to solve particular fields at different scales and for different processes.Therefore,the integration of different types of software is inevitable.However,it is difficult to perform the transfer of the meshes and simulated results among software packages because of the lack of shared data formats or encrypted data formats.An image processing based method for three-dimensional model reconstruction for numerical simulation was proposed,which presents a solution to the integration problem by a series of slice or projection images obtained by the post-processing modules of the numerical simulation software.By means of mapping image pixels to meshes of either finite difference or finite element models,the geometry contour can be extracted to export the stereolithography model.The values of results,represented by color,can be deduced and assigned to the meshes.All the models with data can be directly or indirectly integrated into other software as a continued or new numerical simulation.The three-dimensional reconstruction method has been validated in numerical simulation of castings and case studies were provided in this study.

Evaluation of the Arctic Sea-Ice Simulation on SODA3 Datasets

This study evaluates the Arctic sea-ice simulation of the SODA3 dataset driven by different atmospheric forcing fields and explores the errors of the Arctic sea-ice simulation caused by the forcing field.We find that the SODA3 data driven by different forcing fields represent a significant systematical error in the simulation of Arctic sea-ice concentration,showing a low concentration of thick ice and a high concentration of thin ice.In terms of sea-ice extent,the SODA3 data from different versions well characterize the interannual variability and declining trend in the observed data,but they overestimate the overall Arctic sea-ice extent,which is related to excessive simulation of ice in the sea-ice margin.Compared to observations,all the chosen SODA3 reanalysis versions driven by different atmospheric forcing generally tend to underestimate the Arctic sea-ice thickness,especially for thick ice in the multi-year sea-ice regions.Inaccurate simulations of Arctic sea-ice transport may partly explain the error in SODA3 sea-ice thickness in multi-year sea-ice areas.The results of different SDOA3 versions differ greatly in the Beaufort Sea,the Fram Strait,and the Central Arctic Sea.The difference in sea-ice thickness among different SODA3 versions is primarily due to the thermodynamic contribution,which may come from the diversity of atmospheric forcing fields.Our work provides a reference for using SODA3 data to study Arctic sea ice.

Simulation of optical and electrical synaptic functions in MoS_(2)/α-In_(2)Se_(3) heterojunction memtransistors

Memtransistors combine memristors and field-effect transistors, which can introduce multi-port control and have significant applications for enriching storage methods. In this paper, multilayer α-In2Se3and MoS2were transferred to the substrate by the mechanical exfoliation method, then a heterojunction MoS_(2)/α-In_(2)Se_(3) memtransistor was prepared. Neural synaptic simulations were performed using electrical and optical pulses as input signals. Through measurements, such as excitatory/inhibitory post-synaptic current(EPSC/IPSC), long-term potentiation/depression(LTP/LTD), and paired-pulse facilitation/depression(PPF/PPD), it can be found that the fabricated device could simulate various functions of neural synapses well, and could work as an electronic synapse in artificial neural networks, proposing a possible solution for neuromorphic storage and computation.

3-D fracture network dynamic simulation based on error analysis in rock mass of dam foundation

Accurate 3-D fracture network model for rock mass in dam foundation is of vital importance for stability,grouting and seepage analysis of dam foundation.With the aim of reducing deviation between fracture network model and measured data,a 3-D fracture network dynamic modeling method based on error analysis was proposed.Firstly,errors of four fracture volume density estimation methods(proposed by ODA,KULATILAKE,MAULDON,and SONG)and that of four fracture size estimation methods(proposed by EINSTEIN,SONG and TONON)were respectively compared,and the optimal methods were determined.Additionally,error index representing the deviation between fracture network model and measured data was established with integrated use of fractal dimension and relative absolute error(RAE).On this basis,the downhill simplex method was used to build the dynamic modeling method,which takes the minimum of error index as objective function and dynamically adjusts the fracture density and size parameters to correct the error index.Finally,the 3-D fracture network model could be obtained which meets the requirements.The proposed method was applied for 3-D fractures simulation in Miao Wei hydropower project in China for feasibility verification and the error index reduced from 2.618 to 0.337.

Numerical simulations of full-wave fi elds and analysis of channel wave characteristics in 3-D coal mine roadway models

Currently, numerical simulations of seismic channel waves for the advance detection of geological structures in coal mine roadways focus mainly on modeling two- dimensional wave fields and therefore cannot accurately simulate three-dimensional （3-D） full-wave fields or seismic records in a full-space observation system. In this study, we use the first-order velocity-stress staggered-grid finite difference algorithm to simulate 3-D full-wave fields with P-wave sources in front of coal mine roadways. We determine the three components of velocity Vx, Vy, and Vz for the same node in 3-D staggered-grid finite difference models by calculating the average value of Vy, and Vz of the nodes around the same node. We ascertain the wave patterns and their propagation characteristics in both symmetrical and asymmetric coal mine roadway models. Our simulation results indicate that the Rayleigh channel wave is stronger than the Love channel wave in front of the roadway face. The reflected Rayleigh waves from the roadway face are concentrated in the coal seam, release less energy to the roof and floor, and propagate for a longer distance. There are surface waves and refraction head waves around the roadway. In the seismic records, the Rayleigh wave energy is stronger than that of the Love channel wave along coal walls of the roadway, and the interference of the head waves and surface waves with the Rayleigh channel wave is weaker than with the Love channel wave. It is thus difficult to identify the Love channel wave in the seismic records. Increasing the depth of the receivers in the coal walls can effectively weaken the interference of surface waves with the Rayleigh channel wave, but cannot weaken the interference of surface waves with the Love channel wave. Our research results also suggest that the Love channel wave, which is often used to detect geological structures in coal mine stopes, is not suitable for detecting geological structures in front of coal mine roadways. Instead, the Rayleigh channel wave can be used for the advance detection of geological structures in coal mine roadways.

SIMULATION OF 3-D DEFORMATION AND MATERIAL FLOW DURING ROLL FORGING PROCESS USING SYSTEM OF OVAL-ROUND GROOVE

Basing on the analysis of the traits of the roll forging process, a system-model of computer simulation has been established. Three-dimensional rigid-plastic FEM has been used for the simulation of the deformation process in the oval and round pass rolling, including the entering, rolling, and separating stages. The analysis was conducted using the Deform-3D ver.5.0 code. The important information concerned with the deformation area characteristic, material flow, and velocity field has been presented. Otherwise, the location of the neutral plane in the deformation area was shown clearly.

Research on the Application of Virtual Simulation and 3D Animation Technology in the Teaching of Road and Bridge Majors in Higher Vocational Colleges

The informatization of higher vocational education is the future development trend,and it is also encouraged and promoted by the Ministry of Education.This article focuses on the road and bridge major,combined with the author’s experience in introducing virtual simulation and three-dimensional(3D)animation technology into relevant course teaching in recent years,discusses the application of virtual simulation and 3D animation technology in higher vocational education and promotes classroom revolution,to obtain better teaching effect.