SIMULATION OF 3-D DEFORMATION AND MATERIAL FLOW DURING ROLL FORGING PROCESS USING SYSTEM OF OVAL-ROUND GROOVE

Basing on the analysis of the traits of the roll forging process, a system-model of computer simulation has been established. Three-dimensional rigid-plastic FEM has been used for the simulation of the deformation process in the oval and round pass rolling, including the entering, rolling, and separating stages. The analysis was conducted using the Deform-3D ver.5.0 code. The important information concerned with the deformation area characteristic, material flow, and velocity field has been presented. Otherwise, the location of the neutral plane in the deformation area was shown clearly.

Constrained geometry analysis to resolve 3-D deformations from three ground-based radars

When multiple ground-based radars(GB-rads)are utilized together to resolve three-dimensional(3-D)deformations,the resolving accuracy is related with the measurement geometry constructed by these radars.This paper focuses on constrained geometry analysis to resolve 3-D deformations from three GB-rads.The geometric dilution of precision(GDOP)is utilized to evaluate 3-D deformation accuracy of a single target,and its theoretical equation is derived by building a simplified 3-D coordinate system.Then for a 3-D scene,its optimal accuracy problem is converted into determining the minimum value of an objective function with a boundary constraint.The genetic algorithm is utilized to solve this constrained optimization problem.Numerical simulations are made to validate the correctness of the theoretical analysis results.

High-accuracy 3-D deformation measurement method with an improved structured-light principle

In this paper,a high-accuracy 3-D deformation measurement(HADM)method with structured light is proposed and applied to wing deformation measurement in wind tunnel experiments.The present method employs an arbitrarily arranged fringe projector and a perpendicularly placed camera.The exact phase-height mapping using the phase differences of the projected sinusoidal fringe patterns,as well as the spatial distribution of the fringe,is accurately derived.It not only presents high feasibility but also reduces systemic uncertainties arising from deviations between the ideal model and the real-world conditions.Meanwhile,a dynamic boundary process algorithm is proposed to reduce the measurement uncertainty caused by fringe fracture near the object boundary.It is calibrated that a high accuracy with the average measurement uncertainty of 0.0237 mm is achieved,which is less than 0.01%of the side length of 25 cm of the field of view.In the wind tunnel experiments,the 3-D deformations of the elastic wing,particularly the key geometric parameters such as wing tip position,angle of attack,and dihedral angle,are well reconstructed to provide an in-depth explanation for the aerodynamic characteristics.

Rainfall-triggered waste dump instability analysis based on surface 3D deformation in physical model test

Landslide is the second largest natural disaster after earthquake. It is of significance to study the evolution laws and failure mechanism of landslides based on its surface 3D deformation information. Based on the rainfall-triggered waste dump instability model test, we studied the failure mechanisms of the waste dump by integrating surface deformation and internal slope stress and proposed novel parameters for identifying landslide stability. We developed a noncontact measurement device, which can obtain millimeter-level 3D deformation data for surface scene in physical model test;Then we developed the similar materials and established a test model for a waste dump. Based on the failure characteristics of slope surface, internal stress of slope body and displacement contours during the whole process, we divided the slope instability process in model test into four stages: rainfall infiltration and surface erosion, shallow sliding, deep sliding, and overall instability. Based on the obtained surface deformation data, we calculated the volume change during slope instability process and compared it with the point displacement on slope surface. The results showed that the volume change can not only reflect the slow-ultra acceleration process of slope failure, but also fully reflect the above four stages and reduce the fluctuations caused by random factors. Finally, this paper proposed two stability identification parameters: the volume change rate above the slip surface and the relative velocity of volume change rate. According to the calculation of these two parameters in model test, they can be used for study the deformation and failure mechanism of slope stability.

(1-3)-β-D葡聚糖联合降钙素原、CD4^(+)T淋巴细胞多指标在艾滋病患者马尔尼菲篮状菌感染早期诊断临床研究

目的探讨(1-3)-β-D葡聚糖联合降钙素原(procalcitonin,PCT)、CD4^(+)T淋巴细胞多指标在艾滋病患者马尔尼菲篮状菌感染早期诊断临床研究。方法回顾性选取我院2020年1月—2022年6月住院的120例艾滋病患者为研究对象。依据实验室结果,将其分为马尔尼菲篮状菌感染确诊组(血或组织液培育养出马尔尼菲篮状菌),简称A组(62例),及马尔尼菲篮状菌感染临床诊断组[根据临床症状、体征、血常规及(1-3)-β-D葡聚糖、PCT、CD4^(+)T淋巴细胞多指标诊断],简称B组(58例)。检测患者(1-3)-β-D葡聚糖、PCT、CD4^(+)T淋巴细胞的表达水平,采用受试者工作特征(receiver-operating characteristic,ROC)曲线下面积(area under the curve,AUC)评估上述指标联合检测对艾滋病患者感染马尔尼菲篮状菌的诊断效能。结果A组的(1-3)-β-D葡聚糖和PCT水平均高于B组,CD4^(+)T淋巴细胞个数低于B组(P<0.05);(1-3)-β-D葡聚糖、PCT、CD4^(+)T淋巴细胞联合检测的AUC为0.933,(1-3)-β-D葡聚糖单独检测的AUC是0.812,PCT单独检测的AUC为0.883,CD4^(+)T淋巴细胞单独检测的AUC是0.810,(1-3)-β-D葡聚糖、PCT和CD4^(+)T淋巴细胞联合检测的AUC皆优于三项单独检测,表明(1-3)-β-D葡聚糖、PCT和CD4^(+)T淋巴细胞联合检测的诊断价值皆优于单一指标诊断,且联合检测的特异度、约登指数分别为92.43%和0.580,均高于三项单独检测。结论(1-3)-β-D葡聚糖联合PCT和CD4^(+)T淋巴细胞多指标对艾滋病马尔尼菲篮状菌感染具有非常高的临床诊断价值,能够帮助医生分析出高危风险患者,及时制定治疗方案,同时也承担预后效果的判断依据,对治疗艾滋病马尔尼菲篮状菌感染具有非常重要的研究价值。

血浆(1-3)-β-D葡聚糖诊断新生儿侵袭性真菌感染的价值

探讨在针对新生儿侵袭性真菌感染的诊断中使用血浆(1-3)-β-D葡聚糖能够产生的诊断效能。方法 选取2021年1月到2022年2月因为侵袭性真菌感染于医院寻求医疗干预的新生儿总共60例作为本次研究的一部分研究对象记为1组;另外选取60例健康婴儿作为2组;统计、对比两组患者的血浆(1-3)-β-D葡聚糖水平、CD4+T淋巴细胞数水平;整理PCR技术针对1组患者诊断结果,将其与血浆(1-3)-β-D葡聚糖诊断侵袭性真菌感染的诊断效能进行对比。结果 研究结果显示1组患者的血浆(1-3)-β-D葡聚糖水平、CD4+T淋巴细胞数水平较之于2组患者存在明显差异,1组患者血浆(1-3)-β-D葡聚糖水平更高,而CD4+T淋巴细胞数水平明显更低;P<0.05。在针对诊断效能的考察上,血浆(1-3)-β-D葡聚糖诊断效能和PCR诊断结果之间在灵敏度、特异度方面差异不大,P>0.05。结论 针对罹患侵袭性真菌感染的新生儿使用血浆(1-3)-β-D葡聚糖进行检查,一定程度上能够确保诊断结果的严谨程度,可使用。

The Deformation Analysis of the 3D Alignment Control Network Based on the Multiple Congruence Models

In the construction and maintenance of particle accelerators,all the accelerator elements should be installed in the same coordinate system,only in this way could the devices in the actual world be consistent with the design drawings.However,with the occurrence of the movements of the reinforced concrete cover plates at short notice or building deformations in the long term,the control points upon the engineering structure will be displaced,and the fitness between the subnetwork and the global control network may be irresponsible.Therefore,it is necessary to evaluate the deformations of the 3D alignment control network.Different from the extant investigations,in this paper,to characterize the deformations of the control network,all of the congruent models between the points measured in different epochs have been identified,and the congruence model with the most control points is considered as the primary or fundamental model,the remaining models are recognized as the additional ones.Furthermore,the discrepancies between the primary S-transformation parameters and the additional S-transformation parameters can reflect the relative movements of the additional congruence models.Both the iterative GCT method and the iterative combinatorial theory are proposed to detect multiple congruence models in the control network.Considering the actual work of the alignment,it is essential to identify the competitive models in the monitoring network,which can provide us a hint that,even the fitness between the subnetwork and the global control network is good,there are still deformations which may be ignored.The numerical experiments show that the suggested approaches can describe the deformation of the 3D alignment control network roundly.

Present-day 3D deformation field of Northeast China,observed by GPS and leveling

A broad view of present-day 3D deformation field around the Northeast China region was derived from GPS and leveling observations. We draw the following conclusions： First, the Northeast China region moved towards northwest with an average velocity of 5 ram/a, with respect to South China. The entire Northeast China region was in a low strain state from the strain rate field. Second, we processed two periods of first- order leveling data in 1970s and 1990s, showing the vertical deformation of the Northeast China region is ＂uplift in western part and subsidence in eastern part＇

Parallel computing approach for efficient 3-D X-ray-simulated image reconstruction

Accurate 3-dimensional(3-D)reconstruction technology for nondestructive testing based on digital radiography(DR)is of great importance for alleviating the drawbacks of the existing computed tomography(CT)-based method.The commonly used Monte Carlo simulation method ensures well-performing imaging results for DR.However,for 3-D reconstruction,it is limited by its high time consumption.To solve this problem,this study proposes a parallel computing method to accelerate Monte Carlo simulation for projection images with a parallel interface and a specific DR application.The images are utilized for 3-D reconstruction of the test model.We verify the accuracy of parallel computing for DR and evaluate the performance of two parallel computing modes-multithreaded applications(G4-MT)and message-passing interfaces(G4-MPI)-by assessing parallel speedup and efficiency.This study explores the scalability of the hybrid G4-MPI and G4-MT modes.The results show that the two parallel computing modes can significantly reduce the Monte Carlo simulation time because the parallel speedup increment of Monte Carlo simulations can be considered linear growth,and the parallel efficiency is maintained at a high level.The hybrid mode has strong scalability,as the overall run time of the 180 simulations using 320 threads is 15.35 h with 10 billion particles emitted,and the parallel speedup can be up to 151.36.The 3-D reconstruction of the model is achieved based on the filtered back projection(FBP)algorithm using 180 projection images obtained with the hybrid G4-MPI and G4-MT.The quality of the reconstructed sliced images is satisfactory because the images can reflect the internal structure of the test model.This method is applied to a complex model,and the quality of the reconstructed images is evaluated.

血清25-羟维生素-D3 超敏C反应蛋白及心电图参数与ST段抬高型心肌梗死患者介入治疗后发生恶性心律失常的关系

目的:探讨血清25-羟维生素-D3(25-hydroxyvitamin D3,25-(OH)-D3)、超敏C反应蛋白(High sensitivity C-reactive protein,hs-CRP)、心电图参数变化与ST段抬高型心肌梗死(ST segment elevation myocardial infarction,STEMI)患者经皮冠脉介入术(Percutaneous coronary intervention,PCI)后发生恶性心律失常的关系。方法:选取我院2020年1月至2022年6月实施PCI治疗的193例STEMI患者作为研究对象,根据患者术后72h内是否发生恶性心律失常分为心律失常组38例、对照组155例,对比两组患者入院12h内的25-(OH)-D3、hs-CRP、血清电解质、血常规指标、血脂指标、心肌酶学指标,并对患者PCI术后实施连续动态心电图监测,对比两组患者心电图碎裂QRS波、校正Tp-e间期(Corrected Tp-e interval,Tp-ec)、QT离散度(QT dispersion,Qtd),并采用Logistic回归模型分析上述指标与STEMI患者PCI术后发生恶性心律失常的关系。结果:心律失常组患者的血清25-(OH)-D3水平低于对照组,心律失常组患者的血清hs-CRP、Tp-ec测定值、Qtd测定值、碎裂QRS波检出率均高于对照组,上述指标组间差异均具有统计学意义(P<0.05);心律失常组患者的白细胞(White blood cell,WBC)、肌钙蛋白I(Troponin I,cTnI)、肌酸激酶同工酶(Creatine kinase isoenzyme,CK-MB)、肌红蛋白(Myoglobin,MYO)、K+、Mg 2+水平均高于对照组患者,差异具有统计学意义(P<0.05);Logistic回归模型结果显示:cTnI、CK-MB、K+、hs-CRP、Tp-ec、Qtd增高,碎裂QRS波阳性会显著增大STEMI患者PCI后发生恶性心律失常的风险(P<0.05);血清25-(OH)-D3水平增高会降低STEMI患者PCI后发生恶性心律失常的风险(P<0.05)。结论:STEMI患者血清25-(OH)-D3水平降低、hs-CRP增高、PCI术后Tp-ec、Qtd增高、出现碎裂QRS波会增大患者出现恶性心律失常的风险。

中国地震科学实验场BDS-3定位精度和地壳运动初步分析

我国BDS-3卫星导航系统于2020年7月建成,并为全球用户提供服务,自此开始,中国地震科学实验场(简称“实验场”)的GNSS测站相继接收BDS-3卫星数据,目前已经积累了2年多的观测数据,为BDS-3应用于川滇地区地壳运动监测提供了重要平台和数据保障。为评估实验场BDS-3观测数据的精度及其应用于地壳监测的可行性,本文首先根据各测站所记录的BDS-3的B1I和B3I两个频点的多路径效应和信噪比与卫星高度角之间的关系,对BDS-3的数据质量进行评价。然后,基于高精度数据处理软件GAMIT/GLOBK (10.7版)对各测站同期记录的BDS-3和GPS数据分别进行处理,得到BDS-3和GPS坐标时间序列。基于包括线性项、年周期项和半年周期项等分量的函数模型,利用极大似然法分别对BDS-3和GPS时间序列进行拟合估计,得到各测站的线性速度、年周期和半年周期信号,并对拟合结果对比分析,评定BDS-3和GPS的定位精度。最后,讨论BDS-3定位精度的影响因素和BDS-3水平速度场的区域性特征。研究表明:实验场BDS-3与GPS原始数据质量相当,BDS-3坐标时间序列的均方根残差(RMS)的平均值在N、E、U方向上分别为4.42、4.25和8.34 mm,稍大于GPS的结果。BDS-3与GPS速度场在E方向存在约2.0 mm/a系统性差异。在区域分布特征方面,BDS-3和GPS的速度场、周年期和半年信号没有明显差别。认为目前影响BDS-3定位精度的因素主要为卫星轨道产品不够完善,经验型太阳光压模型和卫星天线相位中心改正模型等欠缺。造成BDS-3和GPS速度场差异的原因主要为两者的定位基准不一致。随着实验场BDS-3观测数据的积累和数据解算模型的改进,BDS-3可望达到GPS的定位精度,并形成独立于GPS的监测系统,为该区地壳运动监测和地震预测提供优质的大地测量产品。

多路径误差对BDS-3变形监测精度的影响

为定量分析BDS-3观测值多路径误差对变形监测精度的影响,选取包含7个站点的某水利工程2022年共128 d的BDS-3监测数据,对监测站点周围树木裁剪树枝前后BDS-3观测值多路径误差、变形监测精度及二者的相关性进行研究。结果表明:1)多路径误差与BDS-3变形监测精度间存在强相关性,与其平面和高程精度的相关系数分别大于0.93和0.81;2)监测站点周围树枝裁剪后,使用B1I和B3I观测值的平均多路径误差从0.676 m、0.426 m降低至0.329 m、0.230 m,N、E、U方向的平均监测精度分别达0.9 mm、0.8 mm、1.7 mm和1.1 mm、1.0 mm、2.2 mm,较裁剪树枝前分别提高63%、69%、58%和52%、61%、48%;3)改变周围观测环境削弱多路径误差的影响后,使用B1I观测值的精度优于使用B3I观测值的精度,因此在BDS-3短基线变形监测的应用中推荐使用B1I观测值。

Elastoplastic 3D Deformation and Stress Analysis of Strip Rolling

An elastoplastic method for analyzing the 3D deformation, stress and transverse distribution of tension stress during cold strip rolling is developed. The analysis is based on the elastoplastic variational principle in which a kinematically admissible velocity field is constructed with the lateral flow function as an unknown function. The stress distribution and volume strain distribution are obtained by solving the simultaneous equations formed by the longitudinal differential equation of equilibrium and constitutive equations. The lateral flow function is determined by minimizing the total energy dissipation rate. Experimental investigation was carried out on a reversible cold mill. The front tension stress distributions in cold rolled strips were measured by a multi roll segmented tension sensing shapemeter. The calculated results are in good agreement with the measured ones.

Building 3-D Human Data Based on Handed Measurement and CNN

3-dimension(3-D)printing technology is growing strongly with many applications,one of which is the garment industry.The application of human body models to the garment industry is necessary to respond to the increasing personalization demand and still guarantee aesthetics.This paper proposes amethod to construct 3-D human models by applying deep learning.We calculate the location of the main slices of the human body,including the neck,chest,belly,buttocks,and the rings of the extremities,using pre-existing information.Then,on the positioning frame,we find the key points(fixed and unaltered)of these key slices and update these points tomatch the current parameters.To add points to a star slice,we use a deep learning model tomimic the form of the human body at that slice position.We use interpolation to produce sub-slices of different body sections based on the main slices to create complete body parts morphologically.We combine all slices to construct a full 3-D representation of the human body.

A Method of Obtaining Deformation Information by Tracing Deformation from Sections for 3D FE Simulation

With the development of computer technology and finite element method, the priority research area of plasticforming has focused on 3D FE simulation of forming processes for components with complicated geometrical shape.These processes have complex deforming mechanism, and different sections have different deforming characteristics.Therefore, for making a simple, convenient, and practical analysis of its deforming law, how to obtain deformationinformation of key sections from the results of 3D FE simulation has become one of problems urgently to be solved.So, a method of obtaining deformation information by tracing deformation from sections for 3D FE simulation hasbeen proposed. From the deformation information got by this method, the deformation law of key locations and thewhole deforming body can be obtained. This method can also help to compare the result from FE simulation withthat from physical modeling. Key procedures of this method have been presented in detail, and it has been testedby applying to 3D FE simulation of precision forging of the blade with a damper platform. The result shows thatthe method is practicable and reliable, and it can also be applied to 3D FE simulation of plastic forming processes ofother components.

Conical Sonic-Supersonic Solutions for the 3-D Steady Full Euler Equations

This paper concerns the sonic-supersonic structures of the transonic crossflow generated by the steady supersonic flow past an infinite cone of arbitrary cross section.Under the conical assumption,the three-dimensional(3-D)steady Euler equations can be projected onto the unit sphere and the state of fluid can be characterized by the polar and azimuthal angles.Given a segment smooth curve as a conical-sonic line in the polar-azimuthal angle plane,we construct a classical conical-supersonic solution near the curve under some reasonable assumptions.To overcome the difficulty caused by the parabolic degeneracy,we apply the characteristic decomposition technique to transform the Euler equations into a new degenerate hyperbolic system in a partial hodograph plane.The singular terms are isolated from the highly nonlinear complicated system and then can be handled successfully.We establish a smooth local solution to the new system in a suitable weighted metric space and then express the solution in terms of the original variables.

Adaptive Window Based 3-D Feature Selection for Multispectral Image Classification Using Firefly Algorithm

Feature extraction is the most critical step in classification of multispectral image.The classification accuracy is mainly influenced by the feature sets that are selected to classify the image.In the past,handcrafted feature sets are used which are not adaptive for different image domains.To overcome this,an evolu-tionary learning method is developed to automatically learn the spatial-spectral features for classification.A modified Firefly Algorithm(FA)which achieves maximum classification accuracy with reduced size of feature set is proposed to gain the interest of feature selection for this purpose.For extracting the most effi-cient features from the data set,we have used 3-D discrete wavelet transform which decompose the multispectral image in all three dimensions.For selecting spatial and spectral features we have studied three different approaches namely overlapping window(OW-3DFS),non-overlapping window(NW-3DFS)adaptive window cube(AW-3DFS)and Pixel based technique.Fivefold Multiclass Support Vector Machine(MSVM)is used for classification purpose.Experiments con-ducted on Madurai LISS IV multispectral image exploited that the adaptive win-dow approach is used to increase the classification accuracy.

Fe_(3)O_(4)/BiOBr/BiOI的制备及降解2,4-D的性能研究

采用水热法制备了微米球花状结构的Fe_(3)O_(4)/BiOBr/BiOI复合材料,通过SEM、XRD、XPS和UV-Vis等手段对催化剂进行表征分析。结果表明,该催化剂对2,4-D具有高效的光降解性能和光催化效率(80 min,88%)。降解速率常数为2.498×10^(-2)min^(-1),分别是Br∶I=5∶5(K=2.004×10^(-2)min^(-1))、BiOBr(K=1.289×10^(-2)min^(-1))和BiOI(K=6.98×10-3min-1)的1.25倍、1.94倍与3.58倍。这是由于Fe_(3)O_(4)/BiOBr/BiOI复合材料内部形成了异质结,利于光生载流子的分离。此外,5次循环实验后,降解效率保持在82.9%,证明该催化剂稳定、可回收、可磁分离。

Precise Three-Dimensional Deformation Retrieval in Large and Complex Deformation Areas via Integration of Offset-Based Unwrapping and Improved Multiple-Aperture SAR Interferometry:Application to the 2016 Kumamoto Earthquake

Conventional synthetic aperture radar(SAR)interferometry(InSAR)has been successfully used to precisely measure surface deformation in the line-of-sight(LOS)direction,while multiple-aperture SAR interferometry(MAI)has provided precise surface deformation in the along-track(AT)direction.Integration of the InSAR and MAI methods enables precise measurement of the two-dimensional(2D)deformation from an interferometric pair;recently,the integration of ascending and descending pairs has allowed the observation of precise three-dimensional(3D)deformation.Precise 3D deformation measurement has been applied to better understand geological events such as earthquakes and volcanic eruptions.The surface deformation related to the 2016 Kumamoto earthquake was large and complex near the fault line;hence,precise 3D deformation retrieval had not yet been attempted.The objectives of this study were to①perform a feasibility test of precise 3D deformation retrieval in large and complex deformation areas through the integration of offset-based unwrapped and improved multiple-aperture SAR interferograms and②observe the 3D deformation field related to the 2016 Kumamoto earthquake,even near the fault lines.Two ascending pairs and one descending the Advanced Land Observing Satellite-2(ALOS-2)Phased Array-type L-band Synthetic Aperture Radar-2(PALSAR-2)pair were used for the 3D deformation retrieval.Eleven in situ Global Positioning System(GPS)measurements were used to validate the 3D deformation measurement accuracy.The achieved accuracy was approximately 2.96,3.75,and 2.86 cm in the east,north,and up directions,respectively.The results show the feasibility of precise 3D deformation measured through the integration of the improved methods,even in a case of large and complex deformation.

Study of High Temperature Deformation and Recrystallization in W9Mo3Cr4V Steel

The behavior of high temperature deformation and recrystallization of W9Mo3Cr4V steel have been studied in this paper. Dynamic precipitation during deformation has also been investigated. In W9Mo3Cr4V steel, stress strain curves exhibit many features. The deformation structures and the effects of deformation parameters on dynamic recrystallization are more complicated than those in low alloy steels. For W9Mo3Cr4V steel, there is a large number of residual carbides on the matrix at high temperature. Also, many second carbides precipitate from the matrix during high temperature deformation. These two kinds of carbides (especially the latter) make the behavior of deformation and dynamic recrystallization in W9Mo3Cr4V steel different from those in low alloy steels. ABSTRACT:The behavior of high temperature deformation and recrystallization of W9Mo3Cr4V steel have been studied in this paper. Dynamic precipitation during deformation has also been investigated. In W9Mo3Cr4V steel, stress strain curves exhibit many features. The deformation structures and the effects of deformation parameters on dynamic recrystallization are more complicated than those in low alloy steels. For W9Mo3Cr4V steel, there is a large number of residual carbides on the matrix at high temperature. Also, many second carbides precipitate from the matrix during high temperature deformation. These two kinds of carbides (especially the latter) make the behavior of deformation and dynamic recrystallization in W9Mo3Cr4V steel different from those in low alloy steels.