SOME PROBLEMS ON JUMP CONDITIONS OF SHOCK WAVES IN 3-DIMENSIONAL SOLIDS

Based on the general conservation laws in continuum mechanics, the Eulerian and Lagrangian descriptions of the jump conditions of shock waves in 3-dimensional solids were presented respectively. The implication of the jump conditions and their relations between each other, particularly the relation between the mass conservation and the displacement continuity, were discussed. Meanwhile the shock wave response curves in 3- dimensional solids, i.e. the Hugoniot curves were analysed, which provide the foundation for studying the coupling effects of shock waves in 3-dimensional solids.

Extending the solid solution range of sodium ferric pyrophosphate:Off‐stoichiometric Na_(3)Fe(2.5)(P_(2)O_(7))_(2)as a novel cathode for sodium‐ion batteries

Iron‐based pyrophosphates are attractive cathodes for sodium‐ion batteries due to their large framework,cost‐effectiveness,and high energy density.However,the understanding of the crystal structure is scarce and only a limited candidates have been reported so far.In this work,we found for the first time that a continuous solid solution,Na_(4−α)Fe_(2+α)_(2)(P_(2)O_(7))_(2)(0≤α≤1,could be obtained by mutual substitution of cations at center‐symmetric Na3 and Na4 sites while keeping the crystal building blocks of anionic P_(2)O_(7) unchanged.In particular,a novel off‐stoichiometric Na_(3)Fe(2.5)(P_(2)O_(7))_(2)is thus proposed,and its structure,energy storage mechanism,and electrochemical performance are extensively investigated to unveil the structure–function relationship.The as‐prepared off‐stoichiometric electrode delivers appealing performance with a reversible discharge capacity of 83 mAh g^(−1),a working voltage of 2.9 V(vs.Na^(+)/Na),the retention of 89.2%of the initial capacity after 500 cycles,and enhanced rate capability of 51 mAh g^(−1)at a current density of 1600 mA g^(−1).This research shows that sodium ferric pyrophosphate could form extended solid solution composition and promising phase is concealed in the range of Na_(4−α)Fe_(2+α)_(2)(P_(2)O_(7))_(2),offering more chances for exploration of new cathode materials for the construction of high‐performance SIBs.

Three-dimensional Reconstruction of Geological Solids Based on Section Topology Reasoning

In order to solve the dynamic reconstruction and local updating problem of three-dimensional geological solids, topology reasoning is used for three-dimensional geological modeling. This can advance the level of the corresponding section automation in implementing the 3D geological solid dynamical reconstruction by the construction of and reasoning on topology on the 3D curved surface. This method has been successfully used in the Nanjing city geological modeling and the Zijin gold mine modeling. The results prove that this method adapts to coplanar section and noncoplanar section data, and improves the efficiency of 3D geological modeling.

CO_(2) mineralization by typical industrial solid wastes for preparing ultrafine CaCO_(3): A review

Mineral carbonation is a promising CO_(2) sequestration strategy that can utilize industrial wastes to convert CO_(2) into high-value CaCO_(3).This review summarizes the advancements in CO_(2) mineralization using typical industrial wastes to prepare ultrafine CaCO_(3).This work surveys the mechanisms of CO_(2) mineralization using these wastes and its capacities to synthesize CaCO_(3),evaluates the effects of carbonation pathways and operating parameters on the preparation of CaCO_(3),analyzes the current industrial application status and economics of this technology.Due to the large amount of impurities in solid wastes,the purity of CaCO_(3) prepared by indirect methods is greater than that prepared by direct methods.Crystalline CaCO_(3) includes three polymorphs.The polymorph of CaCO_(3) synthesized by carbonation process is determined the combined effects of various factors.These parameters essentially impact the nucleation and growth of CaCO_(3) by altering the CO_(2) supersaturation in the reaction system and the surface energy of CaCO_(3) grains.Increasing the initial pH of the solution and the CO_(2)flow rate favors the formation of vaterite,but calcite is formed under excessively high pH.Vaterite formation is favored at lower temperatures and residence time.With increased temperature and prolonged residence time,it passes through aragonite metastable phase and eventually transforms into calcite.Moreover,polymorph modifiers can decrease the surface energy of CaCO_(3) grains,facilitating the synthesis of vaterite.However,the large-scale application of this technology still faces many problems,including high costs,high energy consumption,low calcium leaching rate,low carbonation efficiency,and low product yield.Therefore,it is necessary to investigate ways to accelerate carbonation,optimize operating parameters,develop cost-effective agents,and understand the kinetics of CaCO_(3) nucleation and crystallization to obtain products with specific crystal forms.Furthermore,more studies on life cycle assessment(LCA)should be conducted to fully confirm the feasibility of the developed technologies.

Catalytic Performance of Aquathermolysis and Viscosity Reduction of Heavy Oil over a WO_(3)/ZrO_(2) Solid Acid

Tungstated zirconia(WO_(3)/ZrO_(2))solid acid catalysts with different WO_(3) contents were prepared by a hydrothermal method and then used in the catalytic aquathermolysis of heavy oil from Xinjiang.The WO_(3)/ZrO_(2) solid acid catalyst was characterized by a range of characterization methods,including X-ray diffraction,NH3-temperature programmed desorption,and pyridine infrared spectroscopy.The WO_(3) content of the WO_(3)/ZrO_(2) catalysts had an important impact on the structure and property of the catalysts.When the WO_(3) mass fraction was 20%,it facilitated the formation of tetragonal zirconia,thereby enhancing the creation of robust acidic sites.Acidity is considered to have a strong impact on the catalytic performance of the aquathermolysis of heavy oil.When the catalyst containing 20%WO_(3) was used to catalyze the aquathermolysis of heavy oil under conditions of 14.5 MPa,340℃,and 24 h,the viscosity of heavy oil decreased from 47266 to 5398 mPa·s and the viscosity reduction rate reached 88.6%.The physicochemical properties of heavy oil before and after the aquathermolysis were analyzed using a saturates,aromatics,resins,and asphaltenes analysis,gas chromatography,elemental analysis,densimeter etc.After the aquathermolysis,the saturate and aromatic contents significantly increased from 43.3%to 48.35%and 19.47%to 21.88%,respectively,with large reductions in the content of resin and asphaltene from 28.22%to 25.06%and 5.36%to 2.03%,respectively.The sulfur and nitrogen contents,and the density of the oil were significantly decreased.These factors were likely the main reasons for promoting the viscosity reduction of heavy oil during the aquathermolysis over the WO_(3)/ZrO_(2) solid acid catalysts.

A new method of mesh simplification for 3-Dimension terrain using Laplace operator

This paper proposes a new method to simplify mesh in 3D terrain. The 3D terrain is presented by digital elevation model. First, Laplace operator is introduced to calculate sharp degree of mesh point, which indicates the variation trend of the terrain. Through setting a critical value of sharp degree, feature points are selected. Second, critical mesh points are extracted by an recursive process, and constitute the simplified mesh. Third, the algorithm of linear-square interpolation is employed to restore the characteris- tics of the terrain. Last, the terrain is rendered with color and texture. The experimental results demonstrate that this method can compress data by 16% and the error is lower than 10%.

基于CT扫描和3D打印可视化技术构建石油工程Solid Learning教学新模式

以培养具有创新意识和创新能力的高素质人才为目标,构建石油工程专业Solid Learning教学模式。首先基于CT扫描建立真实的数字岩心模型,利用优化提取算法提取其孔隙网络模型,然后利用3D打印技术建立传统方法不可见的真实模型,最后将打印出的实物模型应用于实验实践教学。应用效果表明,Solid Learning教学模式使地下原本不可见的油藏模型可视化,极大地提高了学生学习的积极性和探索意识,提高了实验及课堂教学的质量,为培养创新性高素质人才奠定了良好的基础,是一种极具推广应用前景的教学新模式。

基于Solid Works及3Ds Max煤矿地面注浆站动态模拟研究

安全生产是煤矿企业实现可持续发展的根本保证.随着新媒体的发展,新型智能煤矿地面自动化注浆站引领着煤矿及相关行业发展,其推广宣传尤为重要.在煤矿地面自动化注浆站展示推广过程中,传统的文字、图片展示由于其存在视觉感知上的局限,已不能满足人们正确理解的需要,在此基础上利用Solid Works及3Ds Max两款三维工具结合的建模方式,针对注浆站自动化生产线开展三维建模和工作流程动态模拟研究,可大大提高自动化注浆站展示推广效果.

石榴石型立方相Li_(7)La_(3)Zr_(2)O_(12)固态电解质的制备及储锂性能

石榴石型立方相Li_(7)La_(3)Zr_(2)O_(12)(LLZO)具有高的离子电导率和热稳定性,在固态锂电池领域颇具应用前景。煅烧温度对制备高性能立方相LLZO至关重要。为此,首先采用不同煅烧温度(1050℃、1100℃、1150℃、1200℃、1250℃)制备了LLZO,然后将10%磺酸甜菜碱改性的聚偏二氟乙烯(SB-PVDF)与90%LLZO复合制备固态电解质膜,并研究其电化学储锂性能。结果表明:在最优煅烧温度1200℃时制备的LLZO为纯立方相结构,相对致密度高达92.4%,离子电导率为1.21×10^(-4)S/cm,活化能为0.335eV,相应的固态锂电池在1.0C充放电时的放电比容量为124.3mAh/g,循环200圈后容量保持率为93.4%,优于其他样品。

Ni doped La_(0.6)Sr_(0.4)FeO_(3-δ) symmetrical electrode for solid oxide fuel cells

The conventional Ni cermet anode suffers from severe carbon deposition and sulfur poisoning when fossil fuels are used. Alternative anode materials are desired for high performance hydrocarbon fuel solid oxide fuel cells （SOFCs）. We report the rational design of a very active Ni doped La0.6Sr0.4FeO3‐δ（LSFN） electrode for hydrocarbon fuel SOFCs. Homogeneously dispersed Ni‐Fe alloy nanoparticles were in situ extruded onto the surface of the LSFN particles during the operation of the cell. Sym‐metric SOFC single cells were prepared by impregnating a LSFN precursor solution onto a YSZ （yt‐tria stabilized zirconia） monolithic cell with a subsequent heat treatment. The open circuit voltage of the LSFN symmetric cell reached 1.18 and 1.0 V in humidified C3H8 and CH4 at 750？？, respective‐ly. The peak power densities of the cells were 400 and 230 mW/cm2 in humidified C3H8 and CH4, respectively. The electrode showed good stability in long term testing, which revealed LSFN has good catalytic activity for hydrocarbon fuel oxidation.

LaNi_(0.6)Fe_(0.4)O_(3)阴极接触材料导电特性调控及其对SOFC电化学性能的影响

鉴于平板式固体氧化物燃料电池(SOFC)电堆对低面电阻、高稳定性阴极接触材料的需求,本研究阐明了LaNi_(0.6)Fe_(0.4)O_(3)(LNF)颗粒尺寸调控对导电和SOFC单电池性能演变的影响机制,优化了LNF预处理工艺,降低了接触组件面电阻,提升了SOFC单电池性能及热循环稳定性。结果表明:预压造粒的样品(LNF-2)与高温烧结预处理的样品(LNF-3)的面电阻更小,分别为0.074和0.076Ω·cm^(2);在750℃施加1 A/cm^(2)电流负载后,能够更快地进入稳态,并保持颗粒尺寸稳定。其中,LNF-2单电池在750℃下的峰值功率密度0.94 W/cm^(2)较未处理的LNF的0.66 W/cm^(2)高,但在热循环过程中性能衰减较大,下降了20%;而LNF-3单电池在20次热循环后峰值功率密度仅下降了4%。本研究对高可靠SOFC电堆装配及其长寿命稳定运行具有指导及参考价值。

FeCl_(3)淋洗修复Pb-Ni复合污染土壤机制研究

Pb、Ni复合污染对土壤的危害大,协同修复难度高。本文以修复建设用地为目标,模拟配制了不同污染程度的Pb、Ni复合污染土壤,以FeCl_(3)为淋洗剂,考察淋洗时间、淋洗剂浓度和液固比等关键参数对Pb、Ni复合污染土壤的影响及其修复机制。结果表明:当FeCl_(3)浓度为0.6 mol/L,液固比为5∶1、淋洗时间为10 h时,Pb、Ni的淋洗效果最好,Pb低、中、高污染土壤的淋洗率分别为80.75%、89.32%和91.45%,Ni低、中、高污染土壤的淋洗率分别为77.31%、92.01%和96.29%;FeCl_(3)对Pb和Ni的快速反应阶段在0~4 h时间段内,至12 h时基本达到平衡。采用双常数和Elovich模型拟合淋洗动力学过程发现,FeCl_(3)对Pb和Ni的淋洗主要是非均相扩散过程;FeCl_(3)对Pb和Ni不同污染程度土壤的去除效果排序为高污染>中污染>低污染,对重金属的去除能力排序为Ni>Pb,FeCl_(3)可有效去除Pb和Ni的弱酸可溶态和可还原态。经FeCl_(3)淋洗后的土壤中Pb和Ni含量均低于第一类建设用地的管制值,对人体健康危害小。

Application of 3-D Geoscience Modeling Technology for the Estimation of Solid Mineral Reserves

Applying new approaches, methods, and technologies for the estimation of reserves can effectively improve the efficiency and accuracy of assessments of solid mineral resources. After analyzing the development of 3-D geoscience modeling technology （3-D GMT）, this paper discusses the application of 3-D GMT for the estimation of solid mineral reserves, emphatically introducing its workflow and two key technologies, 3-D orebody surface modeling, and property modeling. Moreover, the paper analyzes the limitations of traditional methods, such as the section method and geological block method, and points out the advantages of 3-D GMT： building more accurate 3-D orebody models, expressing the internal inhomogeneous attributes of an orebody, reducing the potential for errors in the estimation of reserves, and implementing dynamic estimations of reserves.

NaYSiO_(4)∶Ce^(3+)蓝色荧光粉的发光性质及其在白光发光二极管上的应用

采用高温固相法合成了NaYSiO_(4)∶xCe^(3+)(0.01≤x≤0.05)系列蓝色荧光粉。NaYSiO_(4)∶xCe^(3+)荧光粉在250~360 nm之间的宽带吸收能与紫外LED芯片很好地匹配。NaYSiO_(4)∶xCe^(3+)荧光粉中存在多个Ce^(3+)离子荧光中心,且在紫外光激发下表现出峰值波长位于414 nm附近的宽带蓝光发射。NaYSiO_(4)∶0.02Ce^(3+)荧光粉在300~350 nm紫外光激发下量子效率在25%以上。NaYSiO_(4)∶0.02Ce^(3+)荧光粉表现出优良的化学稳定性,在水中浸泡14 d后荧光强度和量子效率几乎不变。将NaYSiO_(4)∶0.02Ce^(3+)蓝色荧光粉、商用(Sr,Ba)_2SiO_(4)∶Eu^(2+)绿色荧光粉和商用(Ca,Sr)AlSiN_(3)∶Eu^(2+)红色荧光粉涂覆于310 nm紫外LED芯片上制备得到了显色指数高达95的LED器件。当驱动电流从50 mA逐渐增大到300 mA时,制备的LED器件表现出稳定的暖白光发射,其色坐标几乎不变。上述结果说明,本研究报道的NaYSiO_(4)∶0.02Ce^(3+)蓝色荧光粉在紫外LED芯片驱动的白光发光二极管照明上有着潜在应用价值。

NUMERICAL MODELLING OF THREE-DIMENSION CHARACTERISTICS OF WIND-DRIVEN CURRENT IN THE BOHAI SEA

Three- dimension (3-D) wind-driven currents in the Bohai Sea in both winter and summer are calculated by using a 3- D barotropic steady model, and the results are consistent with observed flow char -acteristics. Based on the results, 3- D characteristics of flow, currents at different depths, compensated flow in the lower layer , long and narrow alongshore current, the area of upwelling and downwelling, main circulation in vertical profile, and the current in Bohai Strait are discussed.

Composite solid electrolyte of Na3PS4-PEO for all-solid-state SnS2/Na batteries with excellent interfacial compatibility between electrolyte and Na metal

High ionic conductivity and superior interfacial stability of solid electrolytes at the electrodes are crucial factors for high-performance all-solid-state sodium batteries. Herein, a composite solid electrolyte Na3PS4-polyethylene oxide is synthesized by the solution-phase reaction method with an improved ionic conductivity up to 9.4 × 10-5 S/cm at room temperature. Moreover, polyethylene oxide polymer layer is wrapped homogeneously on the surface of Na3PS4 particles, which could effectively avoid the direct contact between Na3PS4 electrolyte and sodium metal, thus alleviate their side reactions. We demonstrate that all-solid-state battery SnS2/Na with the composite solid electrolyte Na3PS4-polyethylene oxide delivers an enhanced electrochemical performance with 230 m Ah/g after 40 cycles.

Preparation of SO_4^(2-)/TiO_2-MoO_3 Solid Superacid and Its Catalytic Activity in Acetalation and Ketalation

SO4^2-/TiO2-MoO3, a novel solid superacid, has been prepared and its catalytic activity at different synthetic conditions was examined with esterification of n-butanoic acid and n-butyl alcohol as probing reaction.The optimum conditions were also found, that is, the mass ratio of MoO3 used in the compound is 25%, the calcination temperature 450℃, and the soaked consistency of H2SO4 is 0.5mol.L^-1. Then it was applied in the catalytic synthesis of six similar important ketals and acetals as catalyst and revealed high catalytic activity. Under the condition that the molar ratio of aldehyde/ketone to glycol was 1:1.5, the mass ratio of the catalyst to the reactants was 0.5% and the reaction time 1.0 h, the yield of ketals and acetals reached up to 63.2%. The catalyst can be easily recovered and reused.

An efficient synthesis of 2,2-bis(1H-indol-3-yl)-2H-acenaphthen-1-one catalyzed by recyclable solid superacid SO_4^(2-)/TiO_2 under grinding condition

An efficient synthesis of symmetrical 2,2-bis（1H-indol-3-yl）-2H-acenaphthen-1-one is achieved via a reaction of acenaphthe-nequinone and indoles catalyzed by solid superacid SO4^2-/TiO2 under solvent-free conditions at room temperature by grinding, which provides an efficient route to the synthesis of symmetrical 2,2-bis（1H-indol-3-yl）-2H-acenaphthen-1-one.This procedure offers several advantages including solvent-free conditions,excellent yields of products,simple work-up as well as reuse of catalysts which makes it a useful and attractive protocol for the synthesis of these compounds.

Preparation and characterization of poly(lithium acrylate-arcylonitrile)/LiClO_4-LiNO_3-LiBr solid polymer electrolytes

Through orthogonal experiment, a new type of LiClO4-LiNO3-LiBr eutectic salt with optimum mole ratio of n（LiClO4）∶n（LiNO3）∶n（LiBr）=1.6∶3.8∶1.0 was prepared. The poly（lithium acrylate-acrylonitrile）/LiClO4-LiNO3-LiBr solid polymer electrolytes were prepared with poly（lithium acrylate-acrylonitrile） and （LiClO4-LiNO3-LiBr） eutectic salts. The effect of LiClO4-LiNO3-LiBr eutectic salts content on the conductivity of solid polymer electrolytes was studied by alternating current impedance method, and the structures of eutectic salts and solid polymer electrolytes were characterized by differential thermal analysis, infrared spectroscopy and X-ray diffractometry. The results show that the room temperature conductivity of LiClO4-LiNO3-LiBr eutectic salts reaches (3.11×10-4 S·cm-1.) The poly（lithium acrylate-acrylonitrile）/LiClO4-LiNO3-LiBr solid polymer electrolytes possess the highest room temperature conductivity at 70% LiClO4-LiNO3-LiBr eutectic salts content, and exhibit lower glass transition temperature of 75 ℃ compared with that of poly（lithium acrylate-acrylonitrile） of 105 ℃. A complex may be formed in the solid polymer electrolytes from the differential thermal analysis and infrared spectroscopy analysis. X-ray diffraction results show that the poly（lithium acrylate-acrylonitrile） can suppress the crystallization of eutectic salts in this system.

A Facile Solid-phase Synthesis of 3-Carboxycoumarins

Carboxycoumsrins were synthesized via the solid phase synthesis conviently. The resin bound cyclic malonic ester reacted with o-methoxy or o-hydroxybenzaldehydes. Then cyclization was processed under H2SO4 to afford the products in excellent purities and yields.