Elimination of cracks in stainless steel casings via 3D printed sand molds with an internal topology structure

The important supporting component in a gas turbine is the casing,which has the characteristics of large size,complex structure,and thin wall.In the context of existing 3DP sand casting processes,casting crack defects are prone to occur.This leads to an increase in the scrap rate of casings,causing significant resource wastage.Additionally,the presence of cracks poses a significant safety hazard after the casings are put into service.The generation of different types of crack defects in stainless steel casings is closely related to casting stress and the high-temperature concession of the sand mold.Therefore,the types and causes of cracks in stainless steel casing products,based on their structural characteristics,were systematically analyzed.Various sand molds with different internal topology designs were printed using the 3DP technology to investigate the impact of sand mold structures on high-temperature concession.The optimal sand mold structure was used to cast casings,and the crack suppression effect was verified by analyzing its eddy current testing results.The experimental results indicate that the skeleton structure has an excellent effect on suppressing cracks in the casing.This research holds important theoretical and engineering significance in improving the quality of casing castings and reducing production costs.

3D Numerical Simulation of Non-isothermal Resin Transfer Molding Filling Process Using Unstructured Tetrahedron Mesh

We present a numerical formulation for resin flow based on the concept of quasi-steady state situation at the flow front. To be fit for complicated product shapes,we use the four-node unstructured tetrahedron mesh based on which the numerical formulation of temperature and degree of cure is developed. The validity of our method is established in the case where ffexible meshes are used. The results show that the numerical procedure,tested on known data,provides numerically valid and reasonably accurate predictions.

Study on Antigravity Mold Filling by Conservative Scalar Method

By SIMPLE method and Van Leer scheme, a program on numerical simulation for 3D mold filling has been developed. The fluid flow field of gas and liquid is calculated in couples by a single phase N S equation using SIMPLE method, and free surface control equation is handled by Van Leer scheme. Then it is verified by an anti gravity mold filling of thin wall plate. In order to demonstrate its ability to simulate 3D casting, an anti gravity mould filling of a cube is computed by the program.

Exploring the Potential to Uniquely Manufacture Curved VARTM Epoxy Composites Using Cost-Effective FDM Molds

The Resin Infusion or the VARTM (Vacuum Assisted Resin Transfer Molding) process has significant potential to be used to manufacture curved composites. Another way to produce curved or complex geometry is to use 3D printers. 3D or FDM (Fused Deposition Modelling) printers are now being used to produce relatively cheaper curved parts using thermoplastics such as PLA. However, the strength and mechanical performance of these parts is limited and can be enhanced if the polymer is reinforced with a type of fiber for instance. Research is being carried out to produce fiber rein-forced thermoplastic composites but that process is expected to be more expensive than the alternative methods such as injection or compression molding. Furthermore, to understand the manufacture of a hybrid composite using thermoplastics, fibers and epoxy resin, research and investigation need to be carried out. In this research, there are single-sided, double-sided, reusable, disposable and consumable molds. Most of the molds were created either using an FDM printer or manually. These molds were then used to manufacture flat and curved composite structures via the resin injection process, i.e. VARTM with epoxy resin system and glass/carbon/flax fiber reinforcement. By replacing the costly metallic molds by significantly cheaper molds, the cost of production was expected to further reduce. Furthermore, using double-sided PLA molds was not expected to be a threat to the overall cost of the composite part in question compared to double-sided matched molds used in compression molding. Shear strength, tensile strength and charpy impact strength of most of the manufactured composite parts were also investigated. The strengths were compared based on the method of mold usage. The results showed that this method is effective for a cheaper production of curved epoxy resin composites. However, the strength of the part will decrease as the curved profile gets more complicated unless the basic resin infusion process is altered.