With the continuous advancement of technology,the application of 3D printing technology in the field of dental medicine is becoming increasingly widespread.This article aims to explore the current applications and fut...With the continuous advancement of technology,the application of 3D printing technology in the field of dental medicine is becoming increasingly widespread.This article aims to explore the current applications and future potential of 3D printing technology in dental medicine and to analyze its benefits and challenges.It first introduces the current state of 3D printing technology in dental implants,crowns,bridges,orthodontics,and maxillofacial surgery.It then discusses the potential applications of 3D printing technology in oral tissue engineering,drug delivery systems,personalized dental prosthetics,and surgical planning.Finally,it analyzes the benefits of 3D printing technology in dental medicine,such as improving treatment accuracy and patient comfort,and shortening treatment times,while also highlighting the challenges faced,such as costs,material choices,and technical limitations.This article aims to provide a reference for professionals in the field of dental medicine and to promote the further application and development of 3D printing technology in this area.展开更多
Three-dimensional(3D)printing technology is increasingly used in experimental research of geotechnical engineering.Compared to other materials,3D layer-by-layer printing specimens are extremely similar to the inherent...Three-dimensional(3D)printing technology is increasingly used in experimental research of geotechnical engineering.Compared to other materials,3D layer-by-layer printing specimens are extremely similar to the inherent properties of natural layered rock masses.In this paper,soft-hard interbedded rock masses with different dip angles were prepared based on 3D printing(3DP)sand core technology.Uniaxial compression creep tests were conducted to investigate its anisotropic creep behavior based on digital imaging correlation(DIC)technology.The results show that the anisotropic creep behavior of the 3DP soft-hard interbedded rock mass is mainly affected by the dip angles of the weak interlayer when the stress is at low levels.As the stress level increases,the effect of creep stress on its creep anisotropy increases significantly,and the dip angle is no longer the main factor.The minimum value of the long-term strength and creep failure strength always appears in the weak interlayer within 30°–60°,which explains why the failure of the layered rock mass is controlled by the weak interlayer and generally emerges at 45°.The tests results are verified by comparing with theoretical and other published studies.The feasibility of the 3DP soft-hard interbedded rock mass provides broad prospects and application values for 3DP technology in future experimental research.展开更多
In recent years,the government has issued a series of documents to promote the construction of digital campuses.This initiative serves to encourage the deep integration of information technology and intelligent techno...In recent years,the government has issued a series of documents to promote the construction of digital campuses.This initiative serves to encourage the deep integration of information technology and intelligent technology education and digital reform,the combination of virtual reality and campus management is the need for innovative thinking and economic and social development,and then better change our learning style and living environment.The construction of the digital campus is based on virtual reality technology,BIM,GIS,and three-dimensional modeling technology to provide an immersive platform for students,promote the integration of virtual reality technology and education,help teachers,students,and parents to understand all kinds of education information and resources,to achieve their interoperability.From the off-campus environment to the school teaching equipment,teachers to teaching quality certification,and learning,to extracurricular entertainment,opening ceremonies to graduation parties,to bring more efficient,convenient,and safe campus life for teachers,students,and staff in school,and break the traditional information restrictions.展开更多
With the development and progress of science and technology,road and bridge design has experienced rapid development,from the initial manual drawing design to the popularity of Computer-Aided Design(CAD),and then to t...With the development and progress of science and technology,road and bridge design has experienced rapid development,from the initial manual drawing design to the popularity of Computer-Aided Design(CAD),and then to today’s digital software design era.Early designers relied on hand-drawn paper design forms which was time-consuming and error-prone.Digital support for road and bridge design not only saves the design time but the design quality has also achieved a qualitative leap.This paper engages in the application of digital technology in road and bridge design,to provide technical reference for China’s road and bridge engineering design units,to promote the popularity of Civil3D and other advanced design software in the field of engineering design and development,ultimately contributing to the sustainable development of China’s road and bridge engineering.展开更多
After more than 30 years of scientific and social development, surveying and mapping technology by leaps and bounds, engineering surveying technology has undergone tremendous changes. In the process of protecting anci...After more than 30 years of scientific and social development, surveying and mapping technology by leaps and bounds, engineering surveying technology has undergone tremendous changes. In the process of protecting ancient buildings, it is necessary to obtain the precise dimensions of architectural details. In this study, the path of 3D laser scanning combined with BIM technology is explored. Taking the observation and protection of the ancestral hall of the Liu family as an example, this study aims to draw drawings that reflect the relevant information about the ancient buildings, the accurate three-dimensional model of ancient buildings is established with BIM technology, which provides new methods and ideas for the research and protection of ancient buildings. .展开更多
The informatization of higher vocational education is the future development trend,and it is also encouraged and promoted by the Ministry of Education.This article focuses on the road and bridge major,combined with th...The informatization of higher vocational education is the future development trend,and it is also encouraged and promoted by the Ministry of Education.This article focuses on the road and bridge major,combined with the author’s experience in introducing virtual simulation and three-dimensional(3D)animation technology into relevant course teaching in recent years,discusses the application of virtual simulation and 3D animation technology in higher vocational education and promotes classroom revolution,to obtain better teaching effect.展开更多
The application of virtual reality technology has become more and more influential in garden design. Quest3D as a significant software to realize the virtual reality technology is utilized in this study to make a gard...The application of virtual reality technology has become more and more influential in garden design. Quest3D as a significant software to realize the virtual reality technology is utilized in this study to make a garden roaming demonstration system with the gardening design of a classical courtyard as an example. Besides, the advantages and disadvantages of applying Quest3D technology in garden landscape design are elaborated from the perspective of the selection of Quest3D technology, basic procedures for the selection and establishment of software and hardware.展开更多
In order to study the successive deposition and solidification processes of uniform alloy droplets during the drop-on-demand three dimensional（3D） printing method,based on the volume of fluid（VOF） method,a 3D nume...In order to study the successive deposition and solidification processes of uniform alloy droplets during the drop-on-demand three dimensional（3D） printing method,based on the volume of fluid（VOF） method,a 3D numerical model was employed.In this model,the 7075 alloy with larger temperature range for phase change was used.The simulation results show that the successive deposition and solidification processes of uniform 7075 alloy droplets can be well characterized by this model.Simulated droplets shapes agree well with SEM images under the same condition.The effects of deposition and solidification of droplets result in vertical and L-shaped ridges on the surface of droplets,and tips of dendrites appear near the overlap of droplets due to rapid solidification.展开更多
The degradation and mineralization of aniline （AN） using ozone combined with Fenton reagent （O3/Fenton） in a rotating packed bed （RPB） was proposed in this study, and the process （RPB-O3/Fenton） was compared w...The degradation and mineralization of aniline （AN） using ozone combined with Fenton reagent （O3/Fenton） in a rotating packed bed （RPB） was proposed in this study, and the process （RPB-O3/Fenton） was compared with conventional O3/Fenton in a stirred tank reactor （STR-O3/Fenton） or single ozonation in an RPB （RPB-O3）, Effects of high gravity factor, H2O2 dosage, H2O2 dosing method and initial pH on the AN mineralization efficiency were investigated in the RPB-O3/Fenton process, In addition, the behavior of Fe（Ⅱ） was monitored at different H2O2 dosing methods and pH values. Finally, the optimal operation conditions were determined with high gravity factor of 100, initial pH of 5, Fe（Ⅱ） concentration of 0.8 mmol·L-1 and H2O2 dosage of 2.5 ml. Under these conditions, for aniline wastewater at the volume of I L and concentration of 200 mg· L- 1 ,a fast and thorough decay of AN was conducted in 10 min, and the TOC removal efficiency reached 89% in 60 min. The main intermediates of p-benzoquinone, nitrobenzene, maleic acid and oxalic acid were identified by liquid chromatography/mass spectroscopy （LC/MS）, and the degradation pathways of AN in RPB-O3/Fenton system were proposed based on experimental evidence. It could be envisioned that high-gravity technology combined with O3/Fenton processes would be promising in the rapid and efficient mineralization ofwastewater.展开更多
Based on field survey located by GPS, it is obtained landslides＇ location and distribution information by the method of remote sensing in this paper. The vector data of environmental factors that breed and induce lan...Based on field survey located by GPS, it is obtained landslides＇ location and distribution information by the method of remote sensing in this paper. The vector data of environmental factors that breed and induce landslides such as the elevation, the slope, the vegetation cover, the lithology, the rainfall and so on are gained using GIS（geographical information system） techniques of spatial analysis. All the data obtained are managed through building landslide management system. At the same time, the system is made the platform to appraise the relationship between the distribution of landslides and the environmental factors. The results indicate： landslides take place relatively easily in the slope range between 10° and 25°; most landslides are in the mixed area of bush and grass with a coverage degree of from 20° to 65°; the distribution of landslides has a positive relationship with the distribution of annual rainfall. The risk degree of Panxi Area is zoned and mapped by the model of liner stack using GIS technique, and the result indicates： the place of high risk degree is the belt of Panzhihua-Miyi-Dechang-Mugu and southeast of Huili county and Huidong county,and area is about 512 707 hm^2.展开更多
In this study, whole-oil gas chromatographic fingerprint analyses were performed on oils from the Es3^3 reservoir in the Liubei area of the Nanpu Sag. The gas chromatographic peaks of cyclic and branched alkanes with ...In this study, whole-oil gas chromatographic fingerprint analyses were performed on oils from the Es3^3 reservoir in the Liubei area of the Nanpu Sag. The gas chromatographic peaks of cyclic and branched alkanes with relatively high resolution from nCl0 to nC25 were selected to establish a database of whole-oil gas chromatographic peak height ratio fingerprints. Reservoir fluid connectivity was identified by using clustering analysis. This method can reflect the gas chromatography fingerprint information accurately and entirely, and avoid the one-sidedness of the star diagram method which only selects several fixed gas chromatographic peaks.展开更多
A fully automated approach for detecting land use/cover change using remote sensing data, GIS data, GPS data is presented. The integrating raster with vector methods of updating the basic land use/land cover map based...A fully automated approach for detecting land use/cover change using remote sensing data, GIS data, GPS data is presented. The integrating raster with vector methods of updating the basic land use/land cover map based on 3S technology is becoming one of the most important developing directions in 3S application fields, land-use and cover change fields over the world. It has been successful applied in two tasks of the Ministry of Land and Resources of China, and takes some benefit.展开更多
目的基于实时细胞分析(real time cell analysis,RTCA)技术对中药挥发性组分的细胞毒性及抗人腺病毒3型(human adenovirus 3,HAdV-3)的作用进行毒/效整合分析,构建抗病毒药物高通量筛选的新策略。方法采用RTCA技术动态监测不同接种密度...目的基于实时细胞分析(real time cell analysis,RTCA)技术对中药挥发性组分的细胞毒性及抗人腺病毒3型(human adenovirus 3,HAdV-3)的作用进行毒/效整合分析,构建抗病毒药物高通量筛选的新策略。方法采用RTCA技术动态监测不同接种密度的A549细胞48 h生长曲线及10倍梯度稀释的HAdV-3感染A549细胞生长曲线,获得A549细胞最佳接种密度及HAdV-3最佳稀释浓度用于后续实验。以利巴韦林为阳性对照,基于RTCA技术采用曲线下面积(Area Under the Curve,AUC)方法对5种中药挥发性组分的细胞毒性及抗HAdV-3的作用进行毒/效整合分析,并与传统终点法数据处理进行对比。结果终点法中艾叶、柴胡、薄荷、荆芥、牛蒡子、酸枣仁和利巴韦林对细胞的保护率分别为0.73%、12.50%、20.99%、44.50%、27.99%、51.50%和82.70%;AUC法中艾叶、柴胡、薄荷的选择性指数(Selective Index,SI)为负数,分别为-0.57、-0.21和-0.08。荆芥、牛蒡子、酸枣仁和利巴韦林的SI值分别为0.14、0.40、0.72和5.33。以利巴韦林的抗病毒活性为参照,终点法中酸枣仁、牛蒡子和荆芥的抗病毒活性为利巴韦林抗病毒活性的62.27%、33.85%和53.81%;AUC法中酸枣仁、牛蒡子和荆芥的抗病毒活性为利巴韦林抗病毒活性的13.51%、7.50%和2.63%。结论传统终点法与研究采用的AUC法计算结果有较大的差异。传统的抗病毒活性筛选研究多采用终点法检测受试药物对病毒感染细胞的保护作用,无法反映整个感染周期的变化,缺乏细胞毒的数据也会对结果的判断产生偏差。研究提示基于RTCA技术对中药挥发性组分开展抗HAdV-3的毒/效整合评价,采用AUC方法计算药物的选择性指数作为高通量筛选新策略,能快速、精准地判断受试药物的抗病毒活性,具有准确性高、重复性好的优势。展开更多
In recent years, the invert anomalies of operating railway tunnels in water-rich areas occur frequently,which greatly affect the transportation capacity of the railway lines. Tunnel drainage system is a crucial factor...In recent years, the invert anomalies of operating railway tunnels in water-rich areas occur frequently,which greatly affect the transportation capacity of the railway lines. Tunnel drainage system is a crucial factor to ensure the invert stability by regulating the external water pressure(EWP). By means of a threedimensional(3D) printing model, this paper experimentally investigates the deformation behavior of the invert for the tunnels with the traditional drainage system(TDS) widely used in China and its optimized drainage system(ODS) with bottom drainage function. Six test groups with a total of 110 test conditions were designed to consider the design factors and environmental factors in engineering practice,including layout of the drainage system, blockage of the drainage system and groundwater level fluctuation. It was found that there are significant differences in the water discharge, EWP and invert stability for the tunnels with the two drainage systems. Even with a dense arrangement of the external blind tubes, TDS was still difficult to eliminate the excessive EWP below the invert, which is the main cause for the invert instability. Blockage of drainage system further increased the invert uplift and aggravated the track irregularity, especially when the blockage degree is more than 50%. However, ODS can prevent these invert anomalies by reasonably controlling the EWP at tunnel bottom. Even when the groundwater level reached 60 m and the blind tubes were fully blocked, the invert stability can still be maintained and the railway track experienced a settlement of only 1.8 mm. Meanwhile, the on-site monitoring under several rainstorms further showed that the average EWP of the invert was controlled within 84 k Pa, while the maximum settlement of the track slab was only 0.92 mm, which also was in good agreement with the results of model test.展开更多
文摘With the continuous advancement of technology,the application of 3D printing technology in the field of dental medicine is becoming increasingly widespread.This article aims to explore the current applications and future potential of 3D printing technology in dental medicine and to analyze its benefits and challenges.It first introduces the current state of 3D printing technology in dental implants,crowns,bridges,orthodontics,and maxillofacial surgery.It then discusses the potential applications of 3D printing technology in oral tissue engineering,drug delivery systems,personalized dental prosthetics,and surgical planning.Finally,it analyzes the benefits of 3D printing technology in dental medicine,such as improving treatment accuracy and patient comfort,and shortening treatment times,while also highlighting the challenges faced,such as costs,material choices,and technical limitations.This article aims to provide a reference for professionals in the field of dental medicine and to promote the further application and development of 3D printing technology in this area.
基金the support of the National Natural Science Foundation of China(Grant Nos.42207199,52179113,42272333)Zhejiang Postdoctoral Scientific Research Project(Grant Nos.ZJ2022155,ZJ2022156)。
文摘Three-dimensional(3D)printing technology is increasingly used in experimental research of geotechnical engineering.Compared to other materials,3D layer-by-layer printing specimens are extremely similar to the inherent properties of natural layered rock masses.In this paper,soft-hard interbedded rock masses with different dip angles were prepared based on 3D printing(3DP)sand core technology.Uniaxial compression creep tests were conducted to investigate its anisotropic creep behavior based on digital imaging correlation(DIC)technology.The results show that the anisotropic creep behavior of the 3DP soft-hard interbedded rock mass is mainly affected by the dip angles of the weak interlayer when the stress is at low levels.As the stress level increases,the effect of creep stress on its creep anisotropy increases significantly,and the dip angle is no longer the main factor.The minimum value of the long-term strength and creep failure strength always appears in the weak interlayer within 30°–60°,which explains why the failure of the layered rock mass is controlled by the weak interlayer and generally emerges at 45°.The tests results are verified by comparing with theoretical and other published studies.The feasibility of the 3DP soft-hard interbedded rock mass provides broad prospects and application values for 3DP technology in future experimental research.
文摘In recent years,the government has issued a series of documents to promote the construction of digital campuses.This initiative serves to encourage the deep integration of information technology and intelligent technology education and digital reform,the combination of virtual reality and campus management is the need for innovative thinking and economic and social development,and then better change our learning style and living environment.The construction of the digital campus is based on virtual reality technology,BIM,GIS,and three-dimensional modeling technology to provide an immersive platform for students,promote the integration of virtual reality technology and education,help teachers,students,and parents to understand all kinds of education information and resources,to achieve their interoperability.From the off-campus environment to the school teaching equipment,teachers to teaching quality certification,and learning,to extracurricular entertainment,opening ceremonies to graduation parties,to bring more efficient,convenient,and safe campus life for teachers,students,and staff in school,and break the traditional information restrictions.
文摘With the development and progress of science and technology,road and bridge design has experienced rapid development,from the initial manual drawing design to the popularity of Computer-Aided Design(CAD),and then to today’s digital software design era.Early designers relied on hand-drawn paper design forms which was time-consuming and error-prone.Digital support for road and bridge design not only saves the design time but the design quality has also achieved a qualitative leap.This paper engages in the application of digital technology in road and bridge design,to provide technical reference for China’s road and bridge engineering design units,to promote the popularity of Civil3D and other advanced design software in the field of engineering design and development,ultimately contributing to the sustainable development of China’s road and bridge engineering.
文摘After more than 30 years of scientific and social development, surveying and mapping technology by leaps and bounds, engineering surveying technology has undergone tremendous changes. In the process of protecting ancient buildings, it is necessary to obtain the precise dimensions of architectural details. In this study, the path of 3D laser scanning combined with BIM technology is explored. Taking the observation and protection of the ancestral hall of the Liu family as an example, this study aims to draw drawings that reflect the relevant information about the ancient buildings, the accurate three-dimensional model of ancient buildings is established with BIM technology, which provides new methods and ideas for the research and protection of ancient buildings. .
基金2021 Chongqing Energy Vocational College Science and Technology Department Teaching Reform Project"Discussion and Practice of Teaching Reform of"Bridge and Culvert Engineering Construction Technology"Based on Road and Bridge Simulation Software"(202106)。
文摘The informatization of higher vocational education is the future development trend,and it is also encouraged and promoted by the Ministry of Education.This article focuses on the road and bridge major,combined with the author’s experience in introducing virtual simulation and three-dimensional(3D)animation technology into relevant course teaching in recent years,discusses the application of virtual simulation and 3D animation technology in higher vocational education and promotes classroom revolution,to obtain better teaching effect.
文摘The application of virtual reality technology has become more and more influential in garden design. Quest3D as a significant software to realize the virtual reality technology is utilized in this study to make a garden roaming demonstration system with the gardening design of a classical courtyard as an example. Besides, the advantages and disadvantages of applying Quest3D technology in garden landscape design are elaborated from the perspective of the selection of Quest3D technology, basic procedures for the selection and establishment of software and hardware.
基金Projects (51005186,51221001) supported by the National Natural Science Foundation of ChinaProject (85-TZ-2013) supported by the Research Fund of the State Key Laboratory of Solidification Processing(NWPU),ChinaProject (20126102110022) supported by the Doctoral Fund of Ministry of Education of China
文摘In order to study the successive deposition and solidification processes of uniform alloy droplets during the drop-on-demand three dimensional（3D） printing method,based on the volume of fluid（VOF） method,a 3D numerical model was employed.In this model,the 7075 alloy with larger temperature range for phase change was used.The simulation results show that the successive deposition and solidification processes of uniform 7075 alloy droplets can be well characterized by this model.Simulated droplets shapes agree well with SEM images under the same condition.The effects of deposition and solidification of droplets result in vertical and L-shaped ridges on the surface of droplets,and tips of dendrites appear near the overlap of droplets due to rapid solidification.
基金Supported by the National Natural Science Foundations of China(U1610106)Shanxi Excellent Talent Science and Technology Innovation Project(201705D211011)+1 种基金Specialized Research Fund for Sanjin Scholars Program of Shanxi ProvinceNorth University of China Fund for Distinguished Young Scholars
文摘The degradation and mineralization of aniline （AN） using ozone combined with Fenton reagent （O3/Fenton） in a rotating packed bed （RPB） was proposed in this study, and the process （RPB-O3/Fenton） was compared with conventional O3/Fenton in a stirred tank reactor （STR-O3/Fenton） or single ozonation in an RPB （RPB-O3）, Effects of high gravity factor, H2O2 dosage, H2O2 dosing method and initial pH on the AN mineralization efficiency were investigated in the RPB-O3/Fenton process, In addition, the behavior of Fe（Ⅱ） was monitored at different H2O2 dosing methods and pH values. Finally, the optimal operation conditions were determined with high gravity factor of 100, initial pH of 5, Fe（Ⅱ） concentration of 0.8 mmol·L-1 and H2O2 dosage of 2.5 ml. Under these conditions, for aniline wastewater at the volume of I L and concentration of 200 mg· L- 1 ,a fast and thorough decay of AN was conducted in 10 min, and the TOC removal efficiency reached 89% in 60 min. The main intermediates of p-benzoquinone, nitrobenzene, maleic acid and oxalic acid were identified by liquid chromatography/mass spectroscopy （LC/MS）, and the degradation pathways of AN in RPB-O3/Fenton system were proposed based on experimental evidence. It could be envisioned that high-gravity technology combined with O3/Fenton processes would be promising in the rapid and efficient mineralization ofwastewater.
文摘Based on field survey located by GPS, it is obtained landslides＇ location and distribution information by the method of remote sensing in this paper. The vector data of environmental factors that breed and induce landslides such as the elevation, the slope, the vegetation cover, the lithology, the rainfall and so on are gained using GIS（geographical information system） techniques of spatial analysis. All the data obtained are managed through building landslide management system. At the same time, the system is made the platform to appraise the relationship between the distribution of landslides and the environmental factors. The results indicate： landslides take place relatively easily in the slope range between 10° and 25°; most landslides are in the mixed area of bush and grass with a coverage degree of from 20° to 65°; the distribution of landslides has a positive relationship with the distribution of annual rainfall. The risk degree of Panxi Area is zoned and mapped by the model of liner stack using GIS technique, and the result indicates： the place of high risk degree is the belt of Panzhihua-Miyi-Dechang-Mugu and southeast of Huili county and Huidong county,and area is about 512 707 hm^2.
基金funded by Shandong Provincial Key Laboratory of Depositional Mineralization & Sedimentary Minerals (Project DMSM201009)Key Laboratory of Tectonics and Petroleum Resources (China University of Geosciences), Ministry of Education, China (Project TPR-2010-29)
文摘In this study, whole-oil gas chromatographic fingerprint analyses were performed on oils from the Es3^3 reservoir in the Liubei area of the Nanpu Sag. The gas chromatographic peaks of cyclic and branched alkanes with relatively high resolution from nCl0 to nC25 were selected to establish a database of whole-oil gas chromatographic peak height ratio fingerprints. Reservoir fluid connectivity was identified by using clustering analysis. This method can reflect the gas chromatography fingerprint information accurately and entirely, and avoid the one-sidedness of the star diagram method which only selects several fixed gas chromatographic peaks.
文摘A fully automated approach for detecting land use/cover change using remote sensing data, GIS data, GPS data is presented. The integrating raster with vector methods of updating the basic land use/land cover map based on 3S technology is becoming one of the most important developing directions in 3S application fields, land-use and cover change fields over the world. It has been successful applied in two tasks of the Ministry of Land and Resources of China, and takes some benefit.
文摘目的基于实时细胞分析(real time cell analysis,RTCA)技术对中药挥发性组分的细胞毒性及抗人腺病毒3型(human adenovirus 3,HAdV-3)的作用进行毒/效整合分析,构建抗病毒药物高通量筛选的新策略。方法采用RTCA技术动态监测不同接种密度的A549细胞48 h生长曲线及10倍梯度稀释的HAdV-3感染A549细胞生长曲线,获得A549细胞最佳接种密度及HAdV-3最佳稀释浓度用于后续实验。以利巴韦林为阳性对照,基于RTCA技术采用曲线下面积(Area Under the Curve,AUC)方法对5种中药挥发性组分的细胞毒性及抗HAdV-3的作用进行毒/效整合分析,并与传统终点法数据处理进行对比。结果终点法中艾叶、柴胡、薄荷、荆芥、牛蒡子、酸枣仁和利巴韦林对细胞的保护率分别为0.73%、12.50%、20.99%、44.50%、27.99%、51.50%和82.70%;AUC法中艾叶、柴胡、薄荷的选择性指数(Selective Index,SI)为负数,分别为-0.57、-0.21和-0.08。荆芥、牛蒡子、酸枣仁和利巴韦林的SI值分别为0.14、0.40、0.72和5.33。以利巴韦林的抗病毒活性为参照,终点法中酸枣仁、牛蒡子和荆芥的抗病毒活性为利巴韦林抗病毒活性的62.27%、33.85%和53.81%;AUC法中酸枣仁、牛蒡子和荆芥的抗病毒活性为利巴韦林抗病毒活性的13.51%、7.50%和2.63%。结论传统终点法与研究采用的AUC法计算结果有较大的差异。传统的抗病毒活性筛选研究多采用终点法检测受试药物对病毒感染细胞的保护作用,无法反映整个感染周期的变化,缺乏细胞毒的数据也会对结果的判断产生偏差。研究提示基于RTCA技术对中药挥发性组分开展抗HAdV-3的毒/效整合评价,采用AUC方法计算药物的选择性指数作为高通量筛选新策略,能快速、精准地判断受试药物的抗病毒活性,具有准确性高、重复性好的优势。
基金supported by the National Natural Science Foundation of China (Grant No. U1934211)the Open Foundation of National Engineering Research Center of High-speed Railway Construction Technology (Grant No. HSR202005)Scientific Research Project of Hunan Education Department (Grant No.20B596)。
文摘In recent years, the invert anomalies of operating railway tunnels in water-rich areas occur frequently,which greatly affect the transportation capacity of the railway lines. Tunnel drainage system is a crucial factor to ensure the invert stability by regulating the external water pressure(EWP). By means of a threedimensional(3D) printing model, this paper experimentally investigates the deformation behavior of the invert for the tunnels with the traditional drainage system(TDS) widely used in China and its optimized drainage system(ODS) with bottom drainage function. Six test groups with a total of 110 test conditions were designed to consider the design factors and environmental factors in engineering practice,including layout of the drainage system, blockage of the drainage system and groundwater level fluctuation. It was found that there are significant differences in the water discharge, EWP and invert stability for the tunnels with the two drainage systems. Even with a dense arrangement of the external blind tubes, TDS was still difficult to eliminate the excessive EWP below the invert, which is the main cause for the invert instability. Blockage of drainage system further increased the invert uplift and aggravated the track irregularity, especially when the blockage degree is more than 50%. However, ODS can prevent these invert anomalies by reasonably controlling the EWP at tunnel bottom. Even when the groundwater level reached 60 m and the blind tubes were fully blocked, the invert stability can still be maintained and the railway track experienced a settlement of only 1.8 mm. Meanwhile, the on-site monitoring under several rainstorms further showed that the average EWP of the invert was controlled within 84 k Pa, while the maximum settlement of the track slab was only 0.92 mm, which also was in good agreement with the results of model test.
