Effects of Spinning Process on Intergranular Corrosion Behavior of 5A06 Aluminum Alloy

Aluminum alloy tubes were prepared by tube spinning.The intergranular and electrochemical corrosion tests were used to investigate the intergranular corrosion behavior of the 5A06 aluminum alloy blank sample and the spinning sample.Results showed that the intergranular corrosion resistance of the spinning sample was higher than that of the blank sample.In addition,the electrochemical corrosion resistance of the spinning sample was higher than that of the blank sample.The EDS maps indicated a uniform element distribution pattern of aluminum and magnesium.Moreover,the phase composition and lattice constant of the samples were obtained by XRD analysis.The differences in microstructure between the aluminum alloy subjected to the spinning process and the untreated aluminum alloy were determined by EBSD.The differences were mainly attributed to the complex interactions among grain size,dislocations and grain boundaries.

Interfacial reaction behavior and mechanical properties of 5A06 Al alloy soldered with Sn-1Ti-xGa solders at a low temperature

Active soldering of 5A06 Al alloy was performed at 300 ℃ by using Sn-1Ti and Sn-1Ti-0.3Ga active solders, respectively. Theeffects of soldering time on the microstructure and mechanical properties of the joints were investigated. The results showed that the Sn-1Tisolder broke the oxide film on the surface of the Al substrate and induced intergranular diffusion in the Al substrate. When Ga was added tothe solder, severe dissolution pits appeared in the Al substrate due to the action of Sn-1Ti-0.3Ga solder, and many Al particles were flakedfrom the matrix into the solder seam. Under thermal stress and the Ti adsorption effect, the oxide film cracked. With increasing solderingtime, the shear strength of 5A06 Al alloy joints soldered with Sn-1Ti and Sn-1Ti-0.3Ga active solders increased. When soldered for 90 min,the joint soldered with Sn-1Ti-0.3Ga solder had a higher shear strength of 22.12 MPa when compared to Sn-1Ti solder.

Reverse deep drawability of 5A06 aluminum alloy plate at elevated temperatures

In order to avoid the occurrence of fracture at room temperature in reverse deep drawing of aluminum alloy plate, the warm reverse deep drawing method was proposed. The experiments were conducted at room temperature, 280 and 360 ℃ with a 4.5 mm thick 5A06 aluminum alloy plate. The effect of temperature, blank-holding force and gap on the fracture and wrinkle of the reverse deep drawing process was investigated. A fully coupled thermal-mechanical simulation was carried out to obtain the stress distribution through the commercial software of Abaqus/Explicit. The results show that the fracture is avoided at 280 ℃ since the bending-induced stress gradient in the transient area between the inside corner and the straight wall decreases from 505 MPa at RT to 72 MPa at 280 ° C. Although the fracture is avoided as the temperature increases, the wrinkle occurs at the outside die corner at temperature over 280 ° C, where the circumferential compressive stress becomes larger than that at the inside. As the temperature increases to 360 ℃, the fracture occurs due to the excessive softening, the tensile stress in the straight wall reaches rapidly to the tensile strength at the beginning of reverse deep drawing. When 1.5t （t=4.5 mm） blank holding gap is applied at 280 ℃, both the fracture and wrinkle can be avoided, and 420 mm deep cups are drawn successfully.

Formation of Aluminum-magnesium Alloy Cup by Hydrodynamic Deep Drawing with Twin-loading Paths

In order to overcome the limitation of hydro-rim deep drawing, a new process of hydrodynamic deep drawing （HDD） with independent radial hydraulic pressure was proposed. By employing the dynamic explicit analytical software ETA/DynaformS.5 which is based on LS-DYNA3D, the effects of independent radia! hydraulic pressure on the stress, strain and the sheet-thickness of aluminum-magnesium cylindrical cup with a hemispherical bottom were analyzed by numerical simulation. The feature of stress distribution is that there exists a stress-dividing circle in the flange, and the radius of dividing circle was determined by theoretical analysis and stimulation. The experimental results indicate that the reasonable match of independent radial hydraulic pressure and liquid chamber pressure can effectively reduce the thinning at the bottom of hemisphere, decrease the radial stress-strain, and improve the drawing limit of aiuminum-magnesium alloy cylindrical cup.

Effects of Loading Paths on Hydrodynamic Deep Drawing with Independent Radial Hydraulic Pressure of Aluminum Alloy Based on Numerical Simulation

In order to meet the forming demands for low plasticity materials and large height-diameter ratio parts, a new process of hydrodynamic deep drawing （HDD） with independent radial hydraulic pressure is proposed. To investigate the effects of loading paths on the HDD with independent radial hydraulic pressure, the forming process of 5A06 aluminum alloy cylindrical cup with a hemispherical bottom was studied by numerical simulation. By employing the dynamic explicit analytical software ETA/Dynaform based on LS-DYNA3D, the effects of loading paths on the sheet-thickness distribution and surface quality were analyzed. The corresponding relations of the radial hydraulic pressure loading paths and the part＇s strain status on the forming limit diagram （FLD） were also discussed. The results indicated that a sound match between liquid chamber pressure and independent radial hydraulic pressure could restrain the serious thinning at the hemisphere bottom and that through adjusting radial hydraulic pressure could reduce the radial tensile strain and change the strain paths. Therefore, the drawing limit of the aluminum cylindrical cup with a hemispherical bottom could be increased significantly.

Influence of plasma-MIG welding parameters on aluminum weld porosity by orthogonal test

The plasma-MIG welding torch was developed.5A06 aluminum alloys with V-grooves were welded in a single pass in the plasma-MIG welding process and the joints were examined by X-ray diffractometry analysis and mechanical tests.The orthogonal experimental design was used to study the influence of plasma-MIG welding parameters on the aluminum weld porosity.The mixed orthogonal matrix L16(4 4×2 3) and analysis of variance (ANOVA)technique were employed to optimize the welding parameters.The experimental results indicate that the effect of plasma gas flow rate is dominant,the secondary factors are MIG welding voltage,welding speed,wire feed rate and plasma current in turn.Confirmation experiments were conducted under optimum conditions and there was almost no porosity in the welded joints,thus good mechanical performance joints were obtained.

Mechanics analysis of axisymmetric thin-walled part in warm sheet hydroforming

To obtain the influence of fluid pressure and temperature on warm hydroforming of 5A06-O aluminum alloy sheet, the unified mechanics equilibrium equations, which take through- thickness normal stress and friction into account, were established in spherical coordinate system. The distribution of through-thickness normal stress in the thickness direction was determined. The relation between through-thickness normal stress and fluid pressure was also analyzed in different regions of cylindrical cup. Based on the method of subtracting one increasing function from another, the constitutive equation of 5A06-O applied to warm hydroforming was established and in a good agreement with uniaxial tensile data. Based on whether the thickness variation was taken into account, two mechanic models were established to do the comparative study. The results for the studied case show that the calculated stress values are pretty close according to the two models and consistent with results of finite element analysis; the thickness distribution in flange computed by the second model conforms to the experimental data. Finally, the influences of fluid pressure on the flange thickness and radial stress were analyzed.