Low-energy-consumption temperature swing system for CO_(2) capture by combining passive radiative cooling and solar heating

Temperature-swing adsorption(TSA)is an effective technique for CO_(2) capture,but the temperature swing procedure is energy-intensive.Herein,we report a low-energy-consumption system by combining passive radiative cooling and solar heating for the uptake of CO_(2) on commercial activated carbons(CACs).During adsorption,the adsorbents are coated with a layer of hierarchically porous poly(vinylidene fluoride-co-hexafluoropropene)[P(VdF-HFP)HP],which cools the adsorbents to a low temperature under sunlight through radiative cooling.For desorption,CACs with broad absorption of the solar spectrum are exposed to light irradiation for heating.The heating and cooling processes are completely driven by solar energy.Adsorption tests under mimicked sunlight using the CACs show that the performance of this system is comparable to that of the traditional ones.Furthermore,under real sunlight irradiation,the adsorption capacity of the CACs can be well maintained after multiple cycles.The present work may inspire the development of new temperature swing procedures with little energy consumption.

Differences between lower extremity joint running kinetics captured by marker-based and markerless systems were speed dependent

Background:The development of computer vision technology has enabled the use of markerless movement tracking for biomechanical analysis.Recent research has reported the feasibility of markerless systems in motion analysis but has yet to fully explore their utility for capturing faster movements,such as running.Applied studies using markerless systems in clinical and sports settings are still lacking.Thus,the present study compared running biomechanics estimated by marker-based and markerless systems.Given running speed not only affects sports performance but is also associated with clinical injury prevention,diagnosis,and rehabilitation,we aimed to investigate the effects of speed on the comparison of estimated lower extremity joint moments and powers between markerless and marker-based technologies during treadmill running as a concurrent validating study.Methods:Kinematic data from marker-based/markerless technologies were collected,along with ground reaction force data,from 16 young adults running on an instrumented treadmill at 3 speeds:2.24 m/s,2.91 m/s,and 3.58 m/s(5.0 miles/h,6.5 miles/h,and 8.0 miles/h).Sagittal plane moments and powers of the hip,knee,and ankle were calculated by inverse dynamic methods.Time series analysis and statistical parametric mapping were used to determine system differences.Results:Compared to the marker-based system,the markerless system estimated increased lower extremity joint kinetics with faster speed during the swing phase in most cases.Conclusion:Despite the promising application of markerless technology in clinical settings,systematic markerless overestimation requires focused attention.Based on segment pose estimations,the centers of mass estimated by markerless technologies were farther away from the relevant distal joint centers,which led to greater joint moments and powers estimates by markerless vs.marker-based systems.The differences were amplified by running speed.

Quantitative analysis of the morphing wing mechanism of raptors:IMMU-based motion capture system and its application on gestures of a Falco peregrinus

This paper presented a novel tinny motion capture system for measuring bird posture based on inertial and magnetic measurement units that are made up of micromachined gyroscopes, accelerometers, and magnetometers. Multiple quaternion-based extended Kalman filters were implemented to estimate the absolute orientations to achieve high accuracy.Under the guidance of ornithology experts, the extending/contracting motions and flapping cycles were recorded using the developed motion capture system, and the orientation of each bone was also analyzed. The captured flapping gesture of the Falco peregrinus is crucial to the motion database of raptors as well as the bionic design.

High-throughput microfluidic production of carbon capture microcapsules:fundamentals,applications,and perspectives

In the last three decades,carbon dioxide(CO_(2)) emissions have shown a significant increase from various sources.To address this pressing issue,the importance of reducing CO_(2) emissions has grown,leading to increased attention toward carbon capture,utilization,and storage strategies.Among these strategies,monodisperse microcapsules,produced by using droplet microfluidics,have emerged as promising tools for carbon capture,offering a potential solution to mitigate CO_(2) emissions.However,the limited yield of microcapsules due to the inherent low flow rate in droplet microfluidics remains a challenge.In this comprehensive review,the high-throughput production of carbon capture microcapsules using droplet microfluidics is focused on.Specifically,the detailed insights into microfluidic chip fabrication technologies,the microfluidic generation of emulsion droplets,along with the associated hydrodynamic considerations,and the generation of carbon capture microcapsules through droplet microfluidics are provided.This review highlights the substantial potential of droplet microfluidics as a promising technique for large-scale carbon capture microcapsule production,which could play a significant role in achieving carbon neutralization and emission reduction goals.

Configuration Synthesis and Grasping Performance Analysis of Multi-Loop Coupling Capture Mechanism for Launch and Recovery of Torpedo-Shaped Autonomous Underwater Vehicle

Research of capture mechanisms with strong capture adaptability and stable grasp is important to solve the problem of launch and recovery of torpedo-shaped autonomous underwater vehicles(AUVs).A multi-loop coupling capture mechanism with strong adaptability and high retraction rate has been proposed for the launch and recovery of torpedo-shaped AUVs with different morphological features.Firstly,the principle of capturing motion retraction is described based on the appearance characteristics of torpedo-shaped AUVs,and the configuration synthesis of the capture mechanism is carried out using the method of constrained chain synthesis.Secondly,the screw theory is employed to analyze the degree of freedom(DoF)of the capture mechanism.Then,the 3D model of the capture mechanism is established,and the kinematics and dynamics simulations are carried out.Combined with the capture orientation requirements of the capture mechanism,the statics and vibration characteristics analyses are carried out.Furthermore,considering the capture process and the underwater working environment,the motion characteristics and hydraulics characteristics of the capture mechanism are analyzed.Finally,a principle prototype is developed and the torpedo-shaped AUVs capture experiment is completed.The work provides technical reserves for the research and development of AUV capture special equipment.

Recent advances in intermediate-temperature CO_(2) capture: Materials,technologies and applications

Carbon capture,utilization and storage(CCUS) is widely recognized as a vital strategy for mitigating the impact of human induced climate change.Among various CO_(2) adsorbents,intermediate-temperature solid adsorbents have garnered significant attention due to their potential applications in hydrogen utilization,specifically in the water gas shift,steam reforming and gasification processes.These processes are crucial for achieving carbon neutrality.While laboratory-level studies have showcased the high adsorption capacity of these materials via various synthesis and modification methods,their practical application in complex industrial environments remains challenging,impeding the commercialization process.This review aims to critically summarize the recent research progress made in intermediatetemperature(200-400℃) solid CO_(2) adsorbents,particularly focusing on indicators such as cyclability,gas selectivity,and formability,which play vital roles in industrial application scenarios.Additionally,we provide an overview of laboratory-level advanced technologies specifically tailored for industrial applications.Furthermore,we highlight several industrial-ready advanced technologies that can pave the way for overcoming the challenges associated with large-scale implementation.The insights provided by this review aim to assist researchers in identifying the most relevant research directions for industrial applications.By promoting advances in the application of solid adsorbents,we strive to facilitate the ultimate goal of achieving carbon neutrality.

Research progress of CO_(2) capture and mineralization based on natural minerals

Natural minerals,such as kaolinite,halloysite,montmorillonite,attapulgite,bentonite,sepiolite,forsterite,and wollastonite,have considerable potential for use in CO_(2) capture and mineralization due to their abundant reserves,low cost,excellent mechanical prop-erties,and chemical stability.Over the past decades,various methods,such as those involving heat,acid,alkali,organic amine,amino sil-ane,and ionic liquid,have been employed to enhance the CO_(2) capture performance of natural minerals to attain high specific surface area,a large number of pore structures,and rich active sites.Future research on CO_(2) capture by natural minerals will focus on the full utiliza-tion of the properties of natural minerals,adoption of suitable modification methods,and preparation of composite materials with high specific surface area and rich active sites.In addition,we provide a summary of the principle and technical route of direct and indirect mineralization of CO_(2) by natural minerals.This process uses minerals with high calcium and magnesium contents,such as forsterite(Mg_(2)SiO_(4)),serpentine[Mg_(3)Si_(2)O(OH)_(4)],and wollastonite(CaSiO_(3)).The research status of indirect mineralization of CO_(2) using hydro-chloric acid,acetic acid,molten salt,and ammonium salt as media is also introduced in detail.The recovery of additives and high-value-added products during the mineralization process to increase economic benefits is another focus of future research on CO_(2) mineralization by natural minerals.

Highly efficient CO_(2) capture using 2-methylimidazole aqueous solution on laboratory and pilot-scale

To date,the primary industrial carbon capture approach is still absorption using aqueous solutions of alkanolamines.Here,to pursue a substitute for the amine-based approach to improve the CO_(2) capture efficiency and decrease the energy cost further,we report a new carbon capture approach using a 2-methylimidazole(mIm)aqueous solution.The properties and sorption behaviors of this approach have been experimentally investigated.The results show that the mIm solution has higher CO_(2) absorption capacity under relatively higher equilibrium pressure(>130 kPa)and lower desorption heat than the methyldiethanolamine solution.91.6%sorption capacity of mIm solution can be recovered at 353.15 K and 80 kPa.The selectivity for CO_(2)/N_(2) and CO_(2)/CH_(4) can reach an exceptional 7609 and 4324,respectively.Furthermore,the pilot-scale tests were also performed,and the results demonstrate that more than 98%of CO_(2) in the feed gas could be removed and cyclic absorption capacity can reach 1 mol·L^(-1).This work indicates that mIm is an excellent alternative to alkanolamines for carbon capture in the industry.

Regulation of interlayer channels of graphene oxide nanosheets in ultra-thin Pebax mixed-matrix membranes for CO_(2) capture

For the application of carbon capture by membrane process,it is crucial to develop a highly permeable CO_(2)-selective membrane.In this work,we reported an ultra-thin polyether-block-amide(Pebax)mixedmatrix membranes(MMMs)incorporated by graphene oxide(GO),in which the interlayer channels were regulated to optimize the CO_(2)/N_(2) separation performance.Various membrane preparation conditions were systematically investigated on the influence of the membrane structure and separation performance,including the lateral size of GO nanosheets,GO loading,thermal reduction temperature,and time.The results demonstrated that the precisely regulated interlayer channel of GO nanosheets can rapidly provide CO_(2)-selective transport channels due to the synergetic effects of size sieving and preferential adsorption.The GO/Pebax ultra-thin MMMs exhibited CO_(2)/N_(2) selectivity of 72 and CO_(2) permeance of 400 GPU(1 GPU=106 cm^(3)(STP)·cm^(2)·s^(-1)·cmHg^(-1)),providing a promising candidate for CO_(2) capture.

Kinematic calibration under the expectation maximization framework for exoskeletal inertial motion capture system

This study presents a kinematic calibration method for exoskeletal inertial motion capture (EI-MoCap) system with considering the random colored noise such as gyroscopic drift.In this method, the geometric parameters are calibrated by the traditional calibration method at first. Then, in order to calibrate the parameters affected by the random colored noise, the expectation maximization (EM) algorithm is introduced. Through the use of geometric parameters calibrated by the traditional calibration method, the iterations under the EM framework are decreased and the efficiency of the proposed method on embedded system is improved. The performance of the proposed kinematic calibration method is compared to the traditional calibration method. Furthermore, the feasibility of the proposed method is verified on the EI-MoCap system. The simulation and experiment demonstrate that the motion capture precision is significantly improved by 16.79%and 7.16%respectively in comparison to the traditional calibration method.

CO_(2)capture costs of chemical looping combustion of biomass:A comparison of natural and synthetic oxygen carrier

Chemical looping combustion has the potential to be an efficient and low-cost technology capable of contributing to the reduction of the atmospheric concentration of CO_(2) in order to reach the 1.5/2°C goal and mitigate climate change.In this process,a metal oxide is used as oxygen carrier in a dual fluidized bed to generate clean CO_(2) via combustion of biomass.Most commonly,natural ores or synthetic materials are used as oxygen carrier whereas both must meet special requirements for the conversion of solid fuels.Synthetic oxygen carriers are characterized by higher reactivity at the expense of higher costs versus the lower-cost natural ores.To determine the viability of both possibilities,a techno-economic comparison of a synthetic material based on manganese,iron,and copper to the natural ore ilmenite was conducted.The synthetic oxygen carrier was characterized and tested in a pilot plant,where high combustion efficiencies up to 98.4%and carbon capture rates up to 98.5%were reached.The techno-economic assessment resulted in CO_(2) capture costs of 75 and 40€/tCO_(2) for the synthetic and natural ore route respectively,whereas a sensitivity analysis showed the high impact of production costs and attrition rates of the synthetic material.The synthetic oxygen carrier could break even with the natural ore in case of lower production costs and attrition rates,which could be reached by adapting the production process and recycling material.By comparison to state-of-the-art technologies,it is demonstrated that both routes are viable and the capture cost of CO_(2) could be reduced by implementing the chemical looping combustion technology.

Carbon Capture Technologies in OAPEC Member Countries and the Circular Carbon Economy: A Roadmap to Zero Emissions by 2050

Several Organization of Arab Petroleum Exporting Countries (OAPEC) member states (OMSs) have updated their nationally determined contributions (NDCs) with the aim of achieving zero carbon emissions by 2050. Carbon neutrality requires shifting from a linear carbon economy (LCE) to a circular carbon economy (CCE). Carbon capture and storage (CCS) technologies, including reduction, recycle, reuse, removal, and storage technologies, represent an important strategy for achieving such a shift. Herein, we investigate the effects of CCS technology adoption in six OMSs—namely the Kingdom of Saudi Arabia (KSA), Qatar, the United Arab Emirates (UAE), Kuwait, Algeria, and Iraq—by examining their Circular Carbon Economy Index (CCEI) scores, which reflect compliance with CCE-transition policies. Total CCEI, current performance CCEI dimension, and future enabler CCEI dimensions scores were compared among the aforementioned six OMSs and relative to Norway, which was used as a global-high CCEI reference standard. Specifically, CCEI general scope and CCEI oil scope dimension scores were compared. The KSA, Qatar, the UAE, and Kuwait had higher CCEI scores than Algeria and Iraq, reflecting their greater adoption of CCE-transition policies and greater emission-reducing modernization investments. The current performance CCEI scores of Algeria and Iraq appear to be buttressed to some extent by their greater natural carbon sink resources. Based on the findings, we recommend specific actions for OMSs to enhance their CCE transitions and mitigate the negative impacts associated with the associated investments, including: taking rapid practical steps to eliminate carbon oil industry emissions;detailed CCS planning by national oil companies;international cooperation and coordination;and increased investment in domestic CCS utilization infrastructure.

Study on the optimal incident proton energy of ^(7)Li(p,n)^(7)Be neutron source for boron neutron capture therapy

Boron neutron capture therapy(BNCT)is recognized as a precise binary targeted radiotherapy technique that effectively eliminates tumors through the^(10)B(n,α)^(7)Li nuclear reaction.Among various neutron sources,accelerator-based sources have emerged as particularly promising for BNCT applications.The^(7)Li(p,n)^(7)Be reaction is highly regarded as a potential neutron source for BNCT,owing to its low threshold energy for the reaction,significant neutron yield,appropriate average neutron energy,and additional benefits.This study utilized Monte Carlo simulations to model the physical interactions within a lithium target subjected to proton bombardment,including neutron moderation by an MgF_(2)moderator and subsequent BNCT dose analysis using a Snyder head phantom.The study focused on calculating the yields of epithermal neutrons for various incident proton energies,finding an optimal energy at 2.7 MeV.Furthermore,the Snyder head phantom was employed in dose simulations to validate the effectiveness of this specific incident energy when utilizing a^(7)Li(p,n)^(7)Be neutron source for BNCT purposes.

Development of a target capture sequencing SNP genotyping platform for genetic analysis and genomic breeding in rapeseed

Rapeseed(Brassica napus)is an oil crop grown worldwide,making it a key plant species in molecular breeding research.However,the complexity of its polyploid genome increases sequencing costs and reduces sequencing accuracy.Target capture coupled with high-throughput sequencing is an efficient approach for detecting genetic variation at genomic regions or loci of interest.In this study,588 resequenced accessions of rapeseed were used to develop a target capture sequencing SNP genotyping platform named BnaPan50T.The platform comprised 54,765,with 54,058 resequenced markers from the pan-genome,and 855 variant trait-associated markers for 12 agronomic traits.The capture quality of BnaPan50T was demonstrated well in 12 typical accessions.Compared with a conventional genotyping array,BnaPan50T has a high SNP density and a high proportion of SNPs in unique physical positions and in annotated functional genes,promising wide application.Target capture sequencing and wholegenome resequencing in 90 doubled-haploid lines yielded 60%specificity,78%uniformity within tenfold coverage range,and 93%genotyping accuracy for the platform.BnaPan50T was used to construct a genetic map for quantitative trait loci(QTL)mapping,identify 21 unique QTL,and predict several candidate genes for yield-related traits in multiple environments.A set of 132 core SNP loci was selected from BnaPan50T to construct DNA fingerprints and germplasm identification resources.This study provides genomics resources to support target capture sequencing,genetic analysis and genomic breeding of rapeseed.

Context Capture在车辆三维建模中的应用

无人机倾斜摄影技术和Context Capture因具有自动化程度高、建模精度和效率高等特点而被广泛应用于三维建模中。本文使用无人机倾斜摄影技术和Context Capture分别对一辆SUV和一辆三厢轿车进行了三维建模,并对其进行了精度分析。结果表明,采用多条航线的无人机拍摄策略可以充分捕捉车辆各个侧面的细节信息。使用Context Capture构建的车辆三维模型细节清晰可辨,真实地反映了车辆外形。车辆特征点实测数据与航拍数据之间的最大相对误差为0.9%,确保了车辆三维建模的精度要求。

Novel in-capsule synthesis of metal-organic framework for innovative carbon dioxide capture system

Metal-Organic Frameworks(MOFs)have been developed as solid sorbents for CO_(2) capture applications and their properties can be controlled by tuning the chemical blocks of their crystalline units.A number of MOFs(e.g.,HKUST-1)have been developed but the question remains how to deploy them for gas-solid contact.Unfortunately,the direct use of MOFs as nanocrystals would lead to serious problems and risks.Here,for the first time,we report a novel MOF-based hybrid sorbent that is produced via an innovative in-situ microencapsulated synthesis.Using a custom-made double capillary microfluidic assembly,double emulsions of the MOF precursor solutions and UV-curable silicone shell fluid are produced.Subsequently,HKUST-1 MOF is successfully synthesized within the droplets enclosed in the gas permeable microcapsules.The developed MOF-bearing microcapsules uniquely allow the deployment of functional nanocrystals without the challenge of handling ultrafine particles,and further,can selectively reject undesired compounds to protect encapsulated MOFs.

Tailor-made microstructures lead to high-performance robust PEO membrane for CO_(2)capture via green fabrication technique

Emerging excessive greenhouse gas emissions pose great threats to the ecosystem,which thus requires efficient CO_(2)capture to mitigate the disastrous issue.In this report,large molecular size bisphenol A ethoxylate diacrylate(BPA)was employed to crosslink poly(ethylene glycol)methyl ether acrylate(PEGMEA)via the green and rapid UV polymerization strategy.The microstructure of such-prepared membrane could be conveniently tailored by tuning the ratio of the two prepolymers,aiming at obtaining the optimized microstructures with suitable mesh size and PEO sol content,which was approved by a novel low-field nuclear magnetic resonance technique.The optimum membrane overcomes the tradeoff challenge:dense microstructures lower the gas permeability while loose microstructures lower high-pressure-resistance capacity,realizing a high CO_(2)permeability of 1711 Barrer and 100-h long-term running stability under 15 atm.The proposed membrane fabrication approach,hence,opens a novel gate for developing high-performance robust membranes for CO_(2)capture.

Progress and prospect of carbon dioxide capture, utilization and storage in CNPC oilfields

The development history of carbon capture,utilization and storage for enhanced oil recovery(CCUS-EOR)in China is comprehensively reviewed,which consists of three stages:research and exploration,field test and industrial application.The breakthrough understanding of CO_(2) flooding mechanism and field practice in recent years and the corresponding supporting technical achievements of CCUS-EOR project are systematically described.The future development prospects are also pointed out.After nearly 60 years of exploration,the theory of CO_(2) flooding and storage suitable for continental sedimentary reservoirs in China has been innovatively developed.It is suggested that C7–C15 are also important components affecting miscibility of CO_(2) and crude oil.The mechanism of rapid recovery of formation energy by CO_(2) and significant improvement of block productivity and recovery factor has been verified in field tests.The CCUS-EOR reservoir engineering design technology for continental sedimentary reservoir is established.The technology of reservoir engineering parameter design and well spacing optimization has been developed,which focuses on maintaining miscibility to improve oil displacement efficiency and uniform displacement to improve sweep efficiency.The technology of CO_(2) capture,injection and production process,whole-system anticorrosion,storage monitoring and other whole-process supporting technologies have been initially formed.In order to realize the efficient utilization and permanent storage of CO_(2),it is necessary to take the oil reservoir in the oil-water transition zone into consideration,realize the large-scale CO_(2) flooding and storage in the area from single reservoir to the overall structural control system.The oil reservoir in the oil-water transition zone is developed by stable gravity flooding of injecting CO_(2) from structural highs.The research on the storage technology such as the conversion of residual oil and CO_(2) into methane needs to be carried out.

Integrated vacuum pressure swing adsorption and Rectisol process for CO_(2) capture from underground coal gasification syngas

An integrated vacuum pressure swing adsorption(VPSA) and Rectisol process is proposed for CO_(2) capture from underground coal gasification(UCG) syngas. A ten-bed VPSA process with silica gel adsorbent is firstly designed to pre-separate and capture 74.57% CO_(2) with a CO_(2) purity of 98.35% from UCG syngas(CH_(4)/CO/CO_(2)/H_(2)/N_(2)= 30.77%/6.15%/44.10%/18.46%/0.52%, mole fraction, from Shaar Lake Mine Field,Xinjiang Province, China) with a feed pressure of 3.5 MPa. Subsequently, the Rectisol process is constructed to furtherly remove and capture the residual CO_(2)remained in light product gas from the VPSA process using cryogenic methanol(233.15 K, 100%(mass)) as absorbent. A final purified gas with CO_(2) concentration lower than 3% and a regenerated CO_(2) product with CO_(2) purity higher than 95% were achieved by using the Rectisol process. Comparisons indicate that the energy consumption is deceased from 2.143 MJ·kg^(-1) of the single Rectisol process to 1.008 MJ·kg^(-1) of the integrated VPSA & Rectisol process, which demonstrated that the deployed VPSA was an energy conservation process for CO_(2) capture from UCG syngas. Additionally, the high-value gas(e.g., CH_(4)) loss can be decreased and the effects of key operating parameters on the process performances were detailed.

Coin-structured tunable beam shaping assembly design for accelerator-based boron neutron capture therapy for tumors at different depths and sizes

In the past decade,boron neutron capture therapy utilizing an accelerator-based neutron source(ABNS)designed primarily for producing epithermal neutrons has been implemented in the treatment of brain tumors and other cancers.The specifications for designing an epithermal beam are primarily based on the IAEA-TECODC-1223 report,issued in 2001 for reactor neutron sources.Based on this report,the latest perspectives and clinical requirements,we designed an ABNS capable of adjusting the average neutron beam energy.The design was based on a 2.8 MeV,20 mA proton beam bombarding a lithium target to produce neutrons that were subsequently moderated and tuned through a tunable beam shaping assembly(BSA)which can modify the thicknesses and materials of the coin-shaped moderators,back reflectors,filters,and collimators.The simulation results demonstrated that epithermal neutron beams for deep seated tumor treatment,which were generated by utilizing magnesium fluoride with lengths ranging between 28 and 36 cm as the moderator,possessed a treatment depth of 5.6 cm although the neutron flux peak shifts from 4.5 to 1.0 keV.When utilizing a thinner moderator,a less accelerated beam power can meet the treatment requirements.However,higher powers reduced the treatment time.In contrast,employing a thick moderator can reduce the skin dose.In scenarios that required relatively low energy neutron beams,the removal of the thermal neutron filter can raise the thermal neutron flux at the beam port.And the depth of the dose rate peak could be adjusted between 0.25 and 2.20 cm by combining magnesium fluoride and polyethylene coins of different thicknesses.Hence,this device has a better adaptability for the treatment of superficial tumors.Overall,the tunable BSA provides greater flexibility for clinical treatment than common BSA designs that can only adjust the port size.