The current research of electro-hydraulic servo valves mainly focuses on the vibration, pressure oscillating and source of noise. Unfortunately, literatures relating to the study of the influence of the magnetic reluc...The current research of electro-hydraulic servo valves mainly focuses on the vibration, pressure oscillating and source of noise. Unfortunately, literatures relating to the study of the influence of the magnetic reluctances of the magnetic elements are rarely available. This paper aims to analyze the influence of the magnetic reluctances of the magnetic elements on torque motor. Considering these magnetic reluctances ignored in previous literatures, a new mathematical model of servo valve torque motor is developed and proposed based on the fundamental laws of electromagnetism. By using this new mathematical model and the previous models, electromagnetic torque constant and magnetic spring stiffness are evaluated for a given set of torque motor parameters. A computer simulation by using AMESim software is also performed for the same set of torque motor parameters to verify the proposed model. The theoretical results of electromagnetic torque constant and magnetic spring stiffness evaluated by the proposed model render closer agreement with the simulation results than those evaluated by the previous models. In addition, an experimental measurement of the magnetic flux densities in the air-gaps is carried out by using SFL218 servo valve torque motor. Compared with the theoretical results of the magnetic flux densities in the air-gaps evaluated by the previous models, the theoretical results evaluated by the proposed model also show better agreement with the experimental data. The proposed model shows the influence of the magnetic reluctances of the magnetic elements on the servo valve torque motor, and offers modified and analytical expressions to electromagnetic torque constant and magnetic spring stiffness. These modified and analytical expressions could provide guidance more accurately for a linear control design approach and sensitivity analysis on electro-hydraulic servo valves than the previous expressions.展开更多
Attitude control system is one of the most important subsystems in a spacecraft.As a key actuator,the control moment gyroscope(CMG)mainly determines the performance of attitude control system.Whereas,the control accur...Attitude control system is one of the most important subsystems in a spacecraft.As a key actuator,the control moment gyroscope(CMG)mainly determines the performance of attitude control system.Whereas,the control accuracy and output torque smoothness of the CMG depends more on its gimbal servo system.Considering the constraints of size,mass and power consumption for a small satellite,here,a mini-CMG is designed,in which the gimbal servo system is driven by an ultrasonic motor.The good performances of the CMG are obtained by both the ultrasonic motor and the rotary inductosyn.The direct drive of gimbal improves its dynamic performance,with the output bandwidth above 20 Hz.The angular and speed closed-loop control obtains the 0.02°/s gimbal rate,and the output torque resolution better than 2×10^(-3) N·m.The ultrasonic motor provides 1.0N·m self-lock torque during power-off,with 12arc-second position accuracy.展开更多
In order to suppress the periodic interference of the continuous rotary electro-hydraulic servo motor,this paper makes the motor tracking the periodic signals with high accuracy,and improves the influence of friction ...In order to suppress the periodic interference of the continuous rotary electro-hydraulic servo motor,this paper makes the motor tracking the periodic signals with high accuracy,and improves the influence of friction interference to the performance of continuous rotary electro-hydraulic servo motor.The mathematic model of the electro-hydraulic position servo system of the continuous rotary motor was established,and the compound control method was adopted based on the repetitive control,feed forward and PID to suppress the friction interference.Through the simulation,the result confirms that the compound control method decreases the tracking error of the system,increases the robust performance of the system and improves the performance of the continuous rotary electro-hydraulic servo motor.展开更多
In allusion to the problem of friction,leakage,vibration and noise existing in continuous rotary motor electro-hydraulic servo system,highly nonlinearity and uncertainties affecting the system performance,based on the...In allusion to the problem of friction,leakage,vibration and noise existing in continuous rotary motor electro-hydraulic servo system,highly nonlinearity and uncertainties affecting the system performance,based on the transfer function of electro-hydraulic servo system,a kind of Pol-Ind friction model is proposed.The parameters of Pol-Ind friction model are identified and the accurate mathematical model of friction torque is obtained by experiment.The self-correcting wavelet neural network(WNN)controller is proposed,and Adam optimization algorithm is used to perform gradient optimization on scale factor and displacement factor in wavelet basis function,so as to improve the speed and precision of parameter optimization.Through comparative simulation analysis,it is clearly that the self-correcting WNN controller can effectively improve the frequency response and tracking accuracy of continuous rotary motor electro-hydraulic servo system.展开更多
Voice coil motor(VCM) is a special direct drive linear motor, which can convert electric energy directly into mechanical energy without the use of transmission mechanism. VCM has the advantages of simple structure, go...Voice coil motor(VCM) is a special direct drive linear motor, which can convert electric energy directly into mechanical energy without the use of transmission mechanism. VCM has the advantages of simple structure, good rigidity, fast response, silence, high linearity, no cogging force, no pulsation et al. It is widely used in the field of high-precision control. This paper reviews and summarizes the results of VCM research conducted by scholars from various countries, and summarizes the general situation of VCM servo control technology. Firstly, a basic description of VCM’s mathematical model and common control mechanisms is provided. The benefits, drawbacks, and application of control techniques in the field of VCM are all explored in detail;At the same time, the methods to improve control strategy are proposed;Then, combined with the analysis and research of scholars in various countries on VCM, the problems of difficult to establish accurate model, friction disturbance and mechanical vibration of VCM and the solutions to the corresponding problems are summarized;Finally, a summary of VCM’s application fields is provided.展开更多
The servo-motor possesses a strongly nonlinear property due to the effect of the stimulating input voltage, load-torque and environmental operating conditions. So it is rather difficult to derive a traditional mathema...The servo-motor possesses a strongly nonlinear property due to the effect of the stimulating input voltage, load-torque and environmental operating conditions. So it is rather difficult to derive a traditional mathematical model which is capable of expressing both its dynamics and steady-state characteristics. A neural network-based adaptive control strategy is proposed in this paper. In this method, two neural networks have been adopted for system identification (NNI) and control (NNC), respectively. Then, the commonly-used specialized learning has been modified, by taking the NNI output as the approximation output of the servo-motor during the weights training to get sensitivity information. Moreover, the rule for choosing the learning rate is given on the basis of the analysis of Lyapunov stability. Finally, an example of applying the proposed control strategy on a servo-motor is presented to show its effectiveness.展开更多
This paper proposes a method that rotation angle of servo motor and distance values of ultrasonic sensor are used for tracking an object in real-time while the robot keeps regular distance.Object detection distance wi...This paper proposes a method that rotation angle of servo motor and distance values of ultrasonic sensor are used for tracking an object in real-time while the robot keeps regular distance.Object detection distance widens by using ultrasonic sensors and object recognition,and movement of robot is controlled by angle of servo motor and distance of ultrasonic sensors.Not adopting the existing tracking methods:camera,laser-infrared(LRF)and many ultrasonic sensors,the proposed method proves that it is possible to track object using ultrasonic sensor and servo motor.Trajectory of robot is represented and analysed according to movement of object in limited conditions.展开更多
With the background of the control of additional mechanical force droplet transfer in MIG/MAG welding, regarding the AC servo motor as core, a novel oscillating wire feeding system has been developed with excellent pe...With the background of the control of additional mechanical force droplet transfer in MIG/MAG welding, regarding the AC servo motor as core, a novel oscillating wire feeding system has been developed with excellent performances of control and dynamic acceleration which is tested. System constitution and operation principle are introduced in this paper. Influences of parameters on dynamic acceleration performance are analyzed and discussed emphatically, such as oscillating frequency, oscillating amplitude and draw-back speed. Experimental result indicates that according to the technique of welding control, the novel wire feeding system responds rapidly to various kinds of control orders of wire feeding and draw-back, and realizes flexible control of welding wire axial movement, including dynamic shifting,oscillating and so on.展开更多
In order to study the influence of inlet and outlet pressure difference and triangular buffer groove on the internal leakage of continuous rotary electro-hydraulic servo motor,the flow field model of motor with and wi...In order to study the influence of inlet and outlet pressure difference and triangular buffer groove on the internal leakage of continuous rotary electro-hydraulic servo motor,the flow field model of motor with and without triangular groove is established respectively.The mesh model is divided.The pressure distribution of the internal flow field under different pressure difference is analyzed by Fluent.Then,the gap leakage under different pressure difference is calculated,and the leakage curve is obtained.Finally,continuous rotary electro-hydraulic servo motor experimental system is built to conduct the internal leakage test,and the leakage under different pressure difference is measured and compared with the simulation results.The results show that the occurrence of leakage in the motor can be reduced by setting the triangular buffer groove on the flow plate,the simulation and experimental results are consistent.It can be concluded that the larger the pressure difference between the inlet and the outlet of the motor,the larger the gap leakage.The research lays foundation for the application of continuous rotary electro-hydraulic servo motor.展开更多
The company Meridian Air Tire using two method molding,molding machine transmission components design selection using mitsubishi J4 series servo motor and control system.Among them,the two-segment host pitch and rotar...The company Meridian Air Tire using two method molding,molding machine transmission components design selection using mitsubishi J4 series servo motor and control system.Among them,the two-segment host pitch and rotary servo motor selection is the most typical,this paper on its design ideas and selection of a detailed discussion,for manufacturers to correctly select servo motor to provide reference.展开更多
Blank holder force (BHF) control is used to prevent wrinkles of sheet metal in deep drawing process. Based on a novel conception of BHF control technique driven by servo-motor, a new BHF device with six-bar linkage me...Blank holder force (BHF) control is used to prevent wrinkles of sheet metal in deep drawing process. Based on a novel conception of BHF control technique driven by servo-motor, a new BHF device with six-bar linkage mechanism has been designed and manufactured. Whole control system of the new BHF technique was developed, and the basic structure of the hardware configuration of the system was given. Software analysis, implementation and division of the functional modules have been done. Also, the control software in data acquisition and processing module has been developed in the relevant technology of the BHF control system for the requirements of real-time, stability and accuracy. By the new BHF device combined with the hardware and the software system, the BHF can be regulated accurately variation with the predefined BHF profile in deep drawing process.展开更多
为了提高伺服电机系统的动态响应速度、抗干扰能力,解决输入饱和的问题,课题组基于扩张状态观测器(extended state observer,ESO)和抗饱和输入(anti-saturation input,ASI)辅助系统设计了伺服电机的运动控制方案。首先,建立了伺服电机...为了提高伺服电机系统的动态响应速度、抗干扰能力,解决输入饱和的问题,课题组基于扩张状态观测器(extended state observer,ESO)和抗饱和输入(anti-saturation input,ASI)辅助系统设计了伺服电机的运动控制方案。首先,建立了伺服电机的数学模型,将系统阻尼和系统不确定性归为扰动,将扰动设为系统的扩张状态;然后在等效反步滑模控制(backstepping sliding mode control,BSMC)的基础上,引入了ASI辅助系统和ESO,解决输入饱和问题,并抑制内、外干扰;采用双曲正切饱和函数替换符号函数以减小滑模控制的抖振;通过李雅普诺夫稳定性方法检验所提出控制器的稳定性。最后,将基于ESO和ASI的等效反步滑模控制与比例积分微分(proportional integral differential,PID)控制、滑模控制(sliding mode control,SMC)进行仿真对比。结果表明:相较于传统PID和SMC控制器,课题组所设计的控制器可以实现伺服电机的无超调快速响应,解决了输入饱和问题,并具有较好的抗干扰能力和减小输入冲击的作用。展开更多
基金Supported by National Natural Science Foundation of China(Grant No.50975055)
文摘The current research of electro-hydraulic servo valves mainly focuses on the vibration, pressure oscillating and source of noise. Unfortunately, literatures relating to the study of the influence of the magnetic reluctances of the magnetic elements are rarely available. This paper aims to analyze the influence of the magnetic reluctances of the magnetic elements on torque motor. Considering these magnetic reluctances ignored in previous literatures, a new mathematical model of servo valve torque motor is developed and proposed based on the fundamental laws of electromagnetism. By using this new mathematical model and the previous models, electromagnetic torque constant and magnetic spring stiffness are evaluated for a given set of torque motor parameters. A computer simulation by using AMESim software is also performed for the same set of torque motor parameters to verify the proposed model. The theoretical results of electromagnetic torque constant and magnetic spring stiffness evaluated by the proposed model render closer agreement with the simulation results than those evaluated by the previous models. In addition, an experimental measurement of the magnetic flux densities in the air-gaps is carried out by using SFL218 servo valve torque motor. Compared with the theoretical results of the magnetic flux densities in the air-gaps evaluated by the previous models, the theoretical results evaluated by the proposed model also show better agreement with the experimental data. The proposed model shows the influence of the magnetic reluctances of the magnetic elements on the servo valve torque motor, and offers modified and analytical expressions to electromagnetic torque constant and magnetic spring stiffness. These modified and analytical expressions could provide guidance more accurately for a linear control design approach and sensitivity analysis on electro-hydraulic servo valves than the previous expressions.
基金supported by the National Natural Science Foundation of China(No.51575260)the Fundamental Research Funds for the Central Universities(No.NJ20160001)
文摘Attitude control system is one of the most important subsystems in a spacecraft.As a key actuator,the control moment gyroscope(CMG)mainly determines the performance of attitude control system.Whereas,the control accuracy and output torque smoothness of the CMG depends more on its gimbal servo system.Considering the constraints of size,mass and power consumption for a small satellite,here,a mini-CMG is designed,in which the gimbal servo system is driven by an ultrasonic motor.The good performances of the CMG are obtained by both the ultrasonic motor and the rotary inductosyn.The direct drive of gimbal improves its dynamic performance,with the output bandwidth above 20 Hz.The angular and speed closed-loop control obtains the 0.02°/s gimbal rate,and the output torque resolution better than 2×10^(-3) N·m.The ultrasonic motor provides 1.0N·m self-lock torque during power-off,with 12arc-second position accuracy.
基金supported by the Postdoctoral Project of Heilongjiang Province
文摘In order to suppress the periodic interference of the continuous rotary electro-hydraulic servo motor,this paper makes the motor tracking the periodic signals with high accuracy,and improves the influence of friction interference to the performance of continuous rotary electro-hydraulic servo motor.The mathematic model of the electro-hydraulic position servo system of the continuous rotary motor was established,and the compound control method was adopted based on the repetitive control,feed forward and PID to suppress the friction interference.Through the simulation,the result confirms that the compound control method decreases the tracking error of the system,increases the robust performance of the system and improves the performance of the continuous rotary electro-hydraulic servo motor.
基金Supported by the National Natural Science Foundation of China(No.51975164)the China Scholarship Council(No.201908230358)the Fundamental Research Fundation for Universities of Heilongjiang Province。
文摘In allusion to the problem of friction,leakage,vibration and noise existing in continuous rotary motor electro-hydraulic servo system,highly nonlinearity and uncertainties affecting the system performance,based on the transfer function of electro-hydraulic servo system,a kind of Pol-Ind friction model is proposed.The parameters of Pol-Ind friction model are identified and the accurate mathematical model of friction torque is obtained by experiment.The self-correcting wavelet neural network(WNN)controller is proposed,and Adam optimization algorithm is used to perform gradient optimization on scale factor and displacement factor in wavelet basis function,so as to improve the speed and precision of parameter optimization.Through comparative simulation analysis,it is clearly that the self-correcting WNN controller can effectively improve the frequency response and tracking accuracy of continuous rotary motor electro-hydraulic servo system.
文摘Voice coil motor(VCM) is a special direct drive linear motor, which can convert electric energy directly into mechanical energy without the use of transmission mechanism. VCM has the advantages of simple structure, good rigidity, fast response, silence, high linearity, no cogging force, no pulsation et al. It is widely used in the field of high-precision control. This paper reviews and summarizes the results of VCM research conducted by scholars from various countries, and summarizes the general situation of VCM servo control technology. Firstly, a basic description of VCM’s mathematical model and common control mechanisms is provided. The benefits, drawbacks, and application of control techniques in the field of VCM are all explored in detail;At the same time, the methods to improve control strategy are proposed;Then, combined with the analysis and research of scholars in various countries on VCM, the problems of difficult to establish accurate model, friction disturbance and mechanical vibration of VCM and the solutions to the corresponding problems are summarized;Finally, a summary of VCM’s application fields is provided.
基金National Science Foundation of China (No.60572055)Advanced Research Grant of Shanghai Normal University (No.DYL200809)Guangxi Science Foundation (No.0339068).
文摘The servo-motor possesses a strongly nonlinear property due to the effect of the stimulating input voltage, load-torque and environmental operating conditions. So it is rather difficult to derive a traditional mathematical model which is capable of expressing both its dynamics and steady-state characteristics. A neural network-based adaptive control strategy is proposed in this paper. In this method, two neural networks have been adopted for system identification (NNI) and control (NNC), respectively. Then, the commonly-used specialized learning has been modified, by taking the NNI output as the approximation output of the servo-motor during the weights training to get sensitivity information. Moreover, the rule for choosing the learning rate is given on the basis of the analysis of Lyapunov stability. Finally, an example of applying the proposed control strategy on a servo-motor is presented to show its effectiveness.
基金The MKE(The Ministry of Knowledge Economy),Korea,under the Human Resources Development Program for Robotics Support Program supervised by the NIPA(National IT Industry Promotion Agency)(NIPA-2012-H1502-12-1002)The MKE,Korea,under the ITRC(Infor mation Technology Research Center)Support Program supervised by the NIPA(NI-PA-2012-H0301-12-2006)
文摘This paper proposes a method that rotation angle of servo motor and distance values of ultrasonic sensor are used for tracking an object in real-time while the robot keeps regular distance.Object detection distance widens by using ultrasonic sensors and object recognition,and movement of robot is controlled by angle of servo motor and distance of ultrasonic sensors.Not adopting the existing tracking methods:camera,laser-infrared(LRF)and many ultrasonic sensors,the proposed method proves that it is possible to track object using ultrasonic sensor and servo motor.Trajectory of robot is represented and analysed according to movement of object in limited conditions.
基金NationalNatureScienceFoundation (No .5 9775 0 62 )
文摘With the background of the control of additional mechanical force droplet transfer in MIG/MAG welding, regarding the AC servo motor as core, a novel oscillating wire feeding system has been developed with excellent performances of control and dynamic acceleration which is tested. System constitution and operation principle are introduced in this paper. Influences of parameters on dynamic acceleration performance are analyzed and discussed emphatically, such as oscillating frequency, oscillating amplitude and draw-back speed. Experimental result indicates that according to the technique of welding control, the novel wire feeding system responds rapidly to various kinds of control orders of wire feeding and draw-back, and realizes flexible control of welding wire axial movement, including dynamic shifting,oscillating and so on.
基金the National Natural Science Foundation of China(No.51975164)the China Scholarship Council(No.201908230358)the Fundamental Research Fundation for Universities of Heilongjiang Province(No.2019-KYYWF-0205)。
文摘In order to study the influence of inlet and outlet pressure difference and triangular buffer groove on the internal leakage of continuous rotary electro-hydraulic servo motor,the flow field model of motor with and without triangular groove is established respectively.The mesh model is divided.The pressure distribution of the internal flow field under different pressure difference is analyzed by Fluent.Then,the gap leakage under different pressure difference is calculated,and the leakage curve is obtained.Finally,continuous rotary electro-hydraulic servo motor experimental system is built to conduct the internal leakage test,and the leakage under different pressure difference is measured and compared with the simulation results.The results show that the occurrence of leakage in the motor can be reduced by setting the triangular buffer groove on the flow plate,the simulation and experimental results are consistent.It can be concluded that the larger the pressure difference between the inlet and the outlet of the motor,the larger the gap leakage.The research lays foundation for the application of continuous rotary electro-hydraulic servo motor.
文摘The company Meridian Air Tire using two method molding,molding machine transmission components design selection using mitsubishi J4 series servo motor and control system.Among them,the two-segment host pitch and rotary servo motor selection is the most typical,this paper on its design ideas and selection of a detailed discussion,for manufacturers to correctly select servo motor to provide reference.
文摘Blank holder force (BHF) control is used to prevent wrinkles of sheet metal in deep drawing process. Based on a novel conception of BHF control technique driven by servo-motor, a new BHF device with six-bar linkage mechanism has been designed and manufactured. Whole control system of the new BHF technique was developed, and the basic structure of the hardware configuration of the system was given. Software analysis, implementation and division of the functional modules have been done. Also, the control software in data acquisition and processing module has been developed in the relevant technology of the BHF control system for the requirements of real-time, stability and accuracy. By the new BHF device combined with the hardware and the software system, the BHF can be regulated accurately variation with the predefined BHF profile in deep drawing process.