The complex sand-casting process combined with the interactions between process parameters makes it difficult to control the casting quality,resulting in a high scrap rate.A strategy based on a data-driven model was p...The complex sand-casting process combined with the interactions between process parameters makes it difficult to control the casting quality,resulting in a high scrap rate.A strategy based on a data-driven model was proposed to reduce casting defects and improve production efficiency,which includes the random forest(RF)classification model,the feature importance analysis,and the process parameters optimization with Monte Carlo simulation.The collected data includes four types of defects and corresponding process parameters were used to construct the RF model.Classification results show a recall rate above 90% for all categories.The Gini Index was used to assess the importance of the process parameters in the formation of various defects in the RF model.Finally,the classification model was applied to different production conditions for quality prediction.In the case of process parameters optimization for gas porosity defects,this model serves as an experimental process in the Monte Carlo method to estimate a better temperature distribution.The prediction model,when applied to the factory,greatly improved the efficiency of defect detection.Results show that the scrap rate decreased from 10.16% to 6.68%.展开更多
Although disintegrated dolomite,widely distributed across the globe,has conventionally been a focus of research in underground engineering,the issue of slope stability issues in disintegrated dolomite strata is gainin...Although disintegrated dolomite,widely distributed across the globe,has conventionally been a focus of research in underground engineering,the issue of slope stability issues in disintegrated dolomite strata is gaining increasing prominence.This is primarily due to their unique properties,including low strength and loose structure.Current methods for evaluating slope stability,such as basic quality(BQ)and slope stability probability classification(SSPC),do not adequately account for the poor integrity and structural fragmentation characteristic of disintegrated dolomite.To address this challenge,an analysis of the applicability of the limit equilibrium method(LEM),BQ,and SSPC methods was conducted on eight disintegrated dolomite slopes located in Baoshan,Southwest China.However,conflicting results were obtained.Therefore,this paper introduces a novel method,SMRDDS,to provide rapid and accurate assessment of disintegrated dolomite slope stability.This method incorporates parameters such as disintegrated grade,joint state,groundwater conditions,and excavation methods.The findings reveal that six slopes exhibit stability,while two are considered partially unstable.Notably,the proposed method demonstrates a closer match with the actual conditions and is more time-efficient compared with the BQ and SSPC methods.However,due to the limited research on disintegrated dolomite slopes,the results of the SMRDDS method tend to be conservative as a safety precaution.In conclusion,the SMRDDS method can quickly evaluate the current situation of disintegrated dolomite slopes in the field.This contributes significantly to disaster risk reduction for disintegrated dolomite slopes.展开更多
Using melting layer(ML)and non-melting layer(NML)data observed with the X-band dual linear polarization Doppler weather radar(X-POL)in Shunyi,Beijing,the reflectivity(ZH),differential reflectivity(ZDR),and correlation...Using melting layer(ML)and non-melting layer(NML)data observed with the X-band dual linear polarization Doppler weather radar(X-POL)in Shunyi,Beijing,the reflectivity(ZH),differential reflectivity(ZDR),and correlation coefficient(CC)in the ML and NML are obtained in several stable precipitation processes.The prior probability density distributions(PDDs)of the ZH,ZDR and CC are calculated first,and then the probabilities of ZH,ZDR and CC at each radar gate are determined(PBB in the ML and PNB in the NML)by the Bayesian method.When PBB>PNB the gate belongs to the ML,and when PBB<PNB the gate belongs to the NML.The ML identification results with the Bayesian method are contrasUsing melting layer(ML)and non-melting layer(NML)data observed with the X-band dual linear polarization Doppler weather radar(X-POL)in Shunyi,Beijing,the reflectivity(ZH),differential reflectivity(ZDR),and correlation coefficient(CC)in the ML and NML are obtained in several stable precipitation processes.The prior probability density distributions(PDDs)of the ZH,ZDR and CC are calculated first,and then the probabilities of ZH,ZDR and CC at each radar gate are determined(PBB in the ML and PNB in the NML)by the Bayesian method.When PBB>PNB the gate belongs to the ML,and when PBB<PNB the gate belongs to the NML.The ML identification results with the Bayesian method are contrasted under the conditions of the independent PDDs and joint PDDs of the ZH,ZDR and CC.The results suggest that MLs can be identified effectively,although there are slight differences between the two methods.Because the values of the polarization parameters are similar in light rain and dry snow,it is difficult for the polarization radar to distinguish them.After using the Bayesian method to identify the ML,light rain and dry snow can be effectively separated with the X-POL observed data.ted under the conditions of the independent PDDs and joint PDDs of the ZH,ZDR and CC.The results suggest that MLs can be identified effectively,although there are slight differences between the two methods.Because the values of the polarization parameters are similar in light rain and dry snow,it is difficult for the polarization radar to distinguish them.After using the Bayesian method to identify the ML,light rain and dry snow can be effectively separated with the X-POL observed data.展开更多
We describe how the Unit-Feature Spatial Classification Method(UFSCM) can be used operationally to classify cloud types in satellite imagery efficiently and conveniently.By using a combination of Interactive Data Lang...We describe how the Unit-Feature Spatial Classification Method(UFSCM) can be used operationally to classify cloud types in satellite imagery efficiently and conveniently.By using a combination of Interactive Data Language(IDL) and Visual C++(VC) code in combination to extend the technique in three dimensions(3-D),this paper provides an efficient method to implement interactive computer visualization of the 3-D discrimination matrix modification,so as to deal with the bi-spectral limitations of traditional two dimensional(2-D) UFSCM.The case study of cloud-type classification based on FY-2C satellite data (0600 UTC 18 and 0000 UTC 10 September 2007) is conducted by comparison with ground station data, and indicates that 3-D UFSCM makes more use of the pattern recognition information in multi-spectral imagery,resulting in more reasonable results and an improvement over the 2-D method.展开更多
Thermoelectric materials have aroused widespread concern due to their unique ability to directly convert heat to electricity without any moving parts or noxious emissions.Taking advantages of two-dimensional structure...Thermoelectric materials have aroused widespread concern due to their unique ability to directly convert heat to electricity without any moving parts or noxious emissions.Taking advantages of two-dimensional structures of thermoelectric films,the potential applications of thermoelectric materials are diversified,particularly in microdevices.Well-controlled nanostructures in thermoelectric films are effective to optimize the electrical and thermal transport,which can significantly improve the performance of thermoelectric materials.In this paper,various physical and chemical approaches to fabricate thermoelectric films,including inorganic,organic,and inorganic–organic composites,are summarized,where more attentions are paid on the inorganic thermoelectric films for their excellent thermoelectric responses.Additionally,strategies for enhancing the performance of thermoelectric films are also discussed.展开更多
As the key technology of extracting remote sensing information,the classification of remote sensing images has always been the research focus in the field of remote sensing. The paper introduces the classification pro...As the key technology of extracting remote sensing information,the classification of remote sensing images has always been the research focus in the field of remote sensing. The paper introduces the classification process and system of remote sensing images. According to the recent research status of domestic and international remote sensing classification methods,the new study dynamics of remote sensing classification,such as artificial neural networks,support vector machine,active learning and ensemble multi-classifiers,were introduced,providing references for the automatic and intelligent development of remote sensing images classification.展开更多
In recent years,smart textiles have attracted the attention of scholars from all walks of life,but there is an imbalance between functionality and usability,which affects their marketization process.Firstly,five repre...In recent years,smart textiles have attracted the attention of scholars from all walks of life,but there is an imbalance between functionality and usability,which affects their marketization process.Firstly,five representative smart textiles are introduced and their respective wearability is described around preparation methods.Secondly,it is concluded that the preparation methods of smart textiles can be divided into two categories:fiber methods and finishing methods.The fiber methods refer to making smart fibers into smart textiles.Textiles made by fiber methods are breathable and feel good in the hand,but the mechanical properties are influenced by the production equipment,and the process cost is high.The finishing methods refer to the functional finishing of ordinary textiles.Although the finishing method is simple and convenient,it may reduce the comfort of the textile.Finally,applications and new research in various fields of smart textiles are presented with promising prospects.It is anticipated that this review will serve as a theoretical basis for future research and development of smart textiles.Researchers are expected to create new technologies to overcome the tension between functionality and usability,as well as to increase user comfort and convenience.展开更多
A New method of rock drillability classification for impregnated diamond drilling is recommended. The essence of the method is comparing the area of the slots cut respectively on a standard synthetic rock sample and t...A New method of rock drillability classification for impregnated diamond drilling is recommended. The essence of the method is comparing the area of the slots cut respectively on a standard synthetic rock sample and the rock sample being classified by one diamond saw to determine the rock drillability in diamond core drilling. This method has the advantages of good in simulation and stable in comparison standard.展开更多
Driven by the challenge of integrating large amount of experimental data, classification technique emerges as one of the major and popular tools in computational biology and bioinformatics research. Machine learning m...Driven by the challenge of integrating large amount of experimental data, classification technique emerges as one of the major and popular tools in computational biology and bioinformatics research. Machine learning methods, especially kernel methods with Support Vector Machines (SVMs) are very popular and effective tools. In the perspective of kernel matrix, a technique namely Eigen- matrix translation has been introduced for protein data classification. The Eigen-matrix translation strategy has a lot of nice properties which deserve more exploration. This paper investigates the major role of Eigen-matrix translation in classification. The authors propose that its importance lies in the dimension reduction of predictor attributes within the data set. This is very important when the dimension of features is huge. The authors show by numerical experiments on real biological data sets that the proposed framework is crucial and effective in improving classification accuracy. This can therefore serve as a novel perspective for future research in dimension reduction problems.展开更多
In order to improve the accuracy of building structure identification using remote sensing images,a building structure classification method based on multi-feature fusion of UAV remote sensing image is proposed in thi...In order to improve the accuracy of building structure identification using remote sensing images,a building structure classification method based on multi-feature fusion of UAV remote sensing image is proposed in this paper.Three identification approaches of remote sensing images are integrated in this method:object-oriented,texture feature,and digital elevation based on DSM and DEM.So RGB threshold classification method is used to classify the identification results.The accuracy of building structure classification based on each feature and the multi-feature fusion are compared and analyzed.The results show that the building structure classification method is feasible and can accurately identify the structures in large-area remote sensing images.展开更多
This paper proposes an adaptive and diverse hybrid-based ensemble method to improve the performance of binary classification. The proposed method is a non-linear combination of base models and the application of adapt...This paper proposes an adaptive and diverse hybrid-based ensemble method to improve the performance of binary classification. The proposed method is a non-linear combination of base models and the application of adaptive selection of the most suitable model for each data instance. Ensemble method, an important machine learning technique uses multiple single models to construct a hybrid model. A hybrid model generally performs better compared to a single individual model. In a given dataset the application of diverse single models trained with different machine learning algorithms will have different capabilities in recognizing patterns in the given training sample. The proposed approach has been validated on Repeat Buyers Prediction dataset and Census Income Prediction dataset. The experiment results indicate up to 18.5% improvement on F1 score for the Repeat Buyers dataset compared to the best individual model. This improvement also indicates that the proposed ensemble method has an exceptional ability of dealing with imbalanced datasets. In addition, the proposed method outperforms two other commonly used ensemble methods (Averaging and Stacking) in terms of improved F1 score. Finally, our results produced a slightly higher AUC score of 0.718 compared to the previous result of AUC score of 0.712 in the Repeat Buyers competition. This roughly 1% increase AUC score in performance is significant considering a very big dataset such as Repeat Buyers.展开更多
This paper aims to establish a comparison between both geomagnetic activity classification methods on foF2 diurnal variation over solar cycle phases. It concerns first a comparison of geomagnetic activity occurrences ...This paper aims to establish a comparison between both geomagnetic activity classification methods on foF2 diurnal variation over solar cycle phases. It concerns first a comparison of geomagnetic activity occurrences according to both classification methods;and second the geomagnetic effect on foF2 diurnal variation profiles as defined for the equatorial latitudes. The occurrences of the different disturbed geomagnetic activities (recurrent activity (RA), shock activity (SA) and fluctuant activity (FA)) according to both classifications (ancient classification (AC) and new classification (NC)) have been studied at Dakar ionosonde station (Lat: 14.8°N;Long: 342.6°E). Regarding both classifications, the RA occurs more during the decreasing phase. And it’s observed that the RA occurs the most during the increasing phase for the AC and during the minimum phase for the NC. The maximum gap of occurrence (<img src="Edit_e4627ea9-9a9a-4473-9017-202d04a16377.bmp" alt="" /><span><span style="font-family:Verdana;">) between both classifications is <span style="font-size:10.0pt;font-family:;" "=""><span style="font-family:Verdana, Helvetica, Arial;white-space:normal;background-color:#FFFFFF;">-</span></span></span><span style="font-family:;" "=""><span style="font-family:Verdana;">11.1%</span><span style="font-family:Verdana;"> (for the negative value which is observed during the increasing phase) and </span><span style="font-family:Verdana;">+16.74%</span><span style="font-family:Verdana;"> (for the positive one which is observed during the decreasing phase). The occurrence of the SA in relation with both classifications is the lowest during the minimum phase and the maximum occurrence is observed during the maximum and decreasing phases, for the AC, with a value close to </span><span style="font-family:Verdana;">37%</span><span style="font-family:Verdana;"> and for the NC at the maximum phase with a percentage of </span><span style="font-family:Verdana;">54.47%</span><span><span style="font-family:Verdana;">. The maximum gap of occurrence (</span><img src="Edit_20fa141b-ecee-4e06-8024-144ba0969395.bmp" alt="" /></span></span><span style="font-family:Verdana;">) between both classifications is <span style="font-size:10.0pt;font-family:;" "=""><span style="font-family:Verdana, Helvetica, Arial;white-space:normal;background-color:#FFFFFF;">-</span></span></span><span style="font-family:;" "=""><span style="font-family:Verdana;">17.85%</span><span style="font-family:Verdana;"> (for the negative value which is observed at maximum phase) and </span><span style="font-family:Verdana;">+13.53%</span><span style="font-family:Verdana;"> (for the positive one which is observed during the decreasing phase). For both classifications, the FA occurs the least during the minimum phase and the most during the maximum phase for the AC and at maximum and decreasing phases with percentage values of occurrence of roughly </span><span style="font-family:Verdana;">37%</span><span><span style="font-family:Verdana;"> for the NC. The maximum gap of occurrence (</span><img src="Edit_eecb8939-783e-4d43-b92c-80c528c1890b.bmp" alt="" /><span style="font-family:Verdana;"></span></span></span><span style="font-family:Verdana;">) between both classifications is <span style="font-size:10.0pt;font-family:;" "=""><span style="font-family:Verdana, Helvetica, Arial;white-space:normal;background-color:#FFFFFF;">-</span></span>10% (for the negative value which is observed during the decreasing phase) and </span><span style="font-family:;" "=""><span style="font-family:Verdana;">+20.11%</span><span style="font-family:Verdana;"> (for the positive one which is observed during the maximum phase). foF2 diurnal profiles throughout solar cycle phases concerning the AC and the NC have been compared. The FA diurnal profiles don’t present a difference. The RA and the SA present a difference during minimum and increasing phases and the least at maximum and decreasing phases.</span></span></span>展开更多
Lie algorithm combined with differential form Wu's method is used to complete the symmetry classification of partial differential equations(PDEs)containing arbitrary parameter.This process can be reduced to solve ...Lie algorithm combined with differential form Wu's method is used to complete the symmetry classification of partial differential equations(PDEs)containing arbitrary parameter.This process can be reduced to solve a large system of determining equations,which seems rather difficult to solve,then the differential form Wu's method is used to decompose the determining equations into a series of equations,which are easy to solve.To illustrate the usefulness of this method,we apply it to some test problems,and the results show the performance of the present work.展开更多
The classification of thematic mapper imagery in areas with strong topographic variations has proven problematic in the past using a single classifier, due to the changing sun illumination geometry. This often results...The classification of thematic mapper imagery in areas with strong topographic variations has proven problematic in the past using a single classifier, due to the changing sun illumination geometry. This often results in the phenomena of identical object with dissimilar spectrum and different objects with similar spectrum. In this paper, an integrated classification method that combines a decision tree with slope data, tasseled cap transformation indices and maximum likelihood classifier is introduced, to find an optimal classification method for thematic mapper imagery of plain and highland terrains. A Landsat 7 ETM+ image acquired over Hangzhou Bay, in eastern China was used to test the method. The results indicate that the performance of the inte- grated classifier is acceptably good in comparison with that of the existing most widely used maximum likelihood classifier. The integrated classifier depends on hypsography (variation in topography) and the characteristics of ground truth objects (plant and soil). It can greatly reduce the influence of the homogeneous spectrum caused by topographic variation. This integrated classifier might potentially be one of the most accurate classifiers and valuable tool for land cover and land use mapping of plain and highland terrains.展开更多
Regional agriculture is the basis of regional sustainable development,so sustainable regional agricul-tural development is essential to the sustainable development of the whole society and becomes the focus of global ...Regional agriculture is the basis of regional sustainable development,so sustainable regional agricul-tural development is essential to the sustainable development of the whole society and becomes the focus of global research.The classifi cation of regional agricultural structure is the basic work of regional agriculture study.This paper constructs index system(27 indices) of regional agricultural structure types with the three big indices:natural resources,developmental level of the agro-economy,and agro-ecological conditions.This paper also endows weight to every sub-classif ication index by means of AHP and obtains the comprehensive evaluation value of the three types of indices with arithmetic average weight approach.The regional agricultural structure can be classif ied into eight types in accordance with this evaluation results.The empirical study of China shows that the 31 provinces(munici-palities and autonomous regions) are of different agriculture structural types.Finally,countermeasures of sustain-able agricultural development are put forward for the different agriculture structure features.展开更多
This study proposed a weighted sampling hierarchical classification learning method based on an efficient backbone network model to address the problems of high costs,low accuracy,and time-consuming traditional tea di...This study proposed a weighted sampling hierarchical classification learning method based on an efficient backbone network model to address the problems of high costs,low accuracy,and time-consuming traditional tea disease recognition methods.This method enhances the feature extraction ability by conducting hierarchical classification learning based on the EfficientNet model,effectively alleviating the impact of high similarity between tea diseases on the model’s classification performance.To better solve the problem of few and unevenly distributed tea disease samples,this study introduced a weighted sampling scheme to optimize data processing,which not only alleviates the overfitting effect caused by too few sample data but also balances the probability of extracting imbalanced classification data.The experimental results show that the proposed method was significant in identifying both healthy tea leaves and four common leaf diseases of tea(tea algal spot disease,tea white spot disease,tea anthracnose disease,and tea leaf blight disease).After applying the“weighted sampling hierarchical classification learning method”to train 7 different efficient backbone networks,most of their accuracies have improved.The EfficientNet-B1 model proposed in this study achieved an accuracy rate of 99.21%after adopting this learning method,which is higher than EfficientNet-b2(98.82%)and MobileNet-V3(98.43%).In addition,to better apply the results of identifying tea diseases,this study developed a mini-program that operates on WeChat.Users can quickly obtain accurate identification results and corresponding disease descriptions and prevention methods through simple operations.This intelligent tool for identifying tea diseases can serve as an auxiliary tool for farmers,consumers,and related scientific researchers and has certain practical value.展开更多
Engineering rock mass classification,based on empirical relations between rock mass parameters and engineering applications,is commonly used in rock engineering and forms the basis for designing rock structures.The ba...Engineering rock mass classification,based on empirical relations between rock mass parameters and engineering applications,is commonly used in rock engineering and forms the basis for designing rock structures.The basic data required may be obtained from visual observation and laboratory or field tests.However,owing to the discontinuous and variable nature of rock masses,it is difficult for rock engineers to directly obtain the specific design parameters needed.As an alternative,the use of geophysical methods in geomechanics such as seismography may largely address this problem.In this study,25 seismic profiles with the total length of 543 m have been scanned to determine the geomechanical properties of the rock mass in blocks Ⅰ,Ⅲ and Ⅳ-2 of the Choghart iron mine.Moreover,rock joint measurements and sampling for laboratory tests were conducted.The results show that the rock mass rating(RMR) and Q values have a close relation with P-wave velocity parameters,including P-wave velocity in field(V;).P-wave velocity in the laboratory(V;) and the ratio of V;V;(i.e.K;= V;/V;.However,Q value,totally,has greater correlation coefficient and less error than the RMR,In addition,rock mass parameters including rock quality designation(RQD),uniaxial compressive strength(UCS),joint roughness coefficient(JRC) and Schmidt number(RN) show close relationship with P-wave velocity.An equation based on these parameters was obtained to estimate the P-wave velocity in the rock mass with a correlation coefficient of 91%.The velocities in two orthogonal directions and the results of joint study show that the wave velocity anisotropy in rock mass may be used as an efficient tool to assess the strong and weak directions in rock mass.展开更多
The classification of the Northeast China Cold Vortex(NCCV)activity paths is an important way to analyze its characteristics in detail.Based on the daily precipitation data of the northeastern China(NEC)region,and the...The classification of the Northeast China Cold Vortex(NCCV)activity paths is an important way to analyze its characteristics in detail.Based on the daily precipitation data of the northeastern China(NEC)region,and the atmospheric circulation field and temperature field data of ERA-Interim for every six hours,the NCCV processes during the early summer(June)seasons from 1979 to 2018 were objectively identified.Then,the NCCV processes were classified using a machine learning method(k-means)according to the characteristic parameters of the activity path information.The rationality of the classification results was verified from two aspects,as follows:(1)the atmospheric circulation configuration of the NCCV on various paths;and(2)its influences on the climate conditions in the NEC.The obtained results showed that the activity paths of the NCCV could be divided into four types according to such characteristics as the generation origin,movement direction,and movement velocity of the NCCV.These included the generation-eastward movement type in the east of the Mongolia Plateau(eastward movement type or type A);generation-southeast longdistance movement type in the upstream of the Lena River(southeast long-distance movement type or type B);generationeastward less-movement type near Lake Baikal(eastward less-movement type or type C);and the generation-southward less-movement type in eastern Siberia(southward less-movement type or type D).There were obvious differences observed in the atmospheric circulation configuration and the climate impact of the NCCV on the four above-mentioned types of paths,which indicated that the classification results were reasonable.展开更多
基金financially supported by the National Key Research and Development Program of China(2022YFB3706800,2020YFB1710100)the National Natural Science Foundation of China(51821001,52090042,52074183)。
文摘The complex sand-casting process combined with the interactions between process parameters makes it difficult to control the casting quality,resulting in a high scrap rate.A strategy based on a data-driven model was proposed to reduce casting defects and improve production efficiency,which includes the random forest(RF)classification model,the feature importance analysis,and the process parameters optimization with Monte Carlo simulation.The collected data includes four types of defects and corresponding process parameters were used to construct the RF model.Classification results show a recall rate above 90% for all categories.The Gini Index was used to assess the importance of the process parameters in the formation of various defects in the RF model.Finally,the classification model was applied to different production conditions for quality prediction.In the case of process parameters optimization for gas porosity defects,this model serves as an experimental process in the Monte Carlo method to estimate a better temperature distribution.The prediction model,when applied to the factory,greatly improved the efficiency of defect detection.Results show that the scrap rate decreased from 10.16% to 6.68%.
基金supported by the National Natural Science Foundation of China(Grant No.42162026)the Applied Basic Research Foundation of Yunnan Province(Grant No.202201AT070083).
文摘Although disintegrated dolomite,widely distributed across the globe,has conventionally been a focus of research in underground engineering,the issue of slope stability issues in disintegrated dolomite strata is gaining increasing prominence.This is primarily due to their unique properties,including low strength and loose structure.Current methods for evaluating slope stability,such as basic quality(BQ)and slope stability probability classification(SSPC),do not adequately account for the poor integrity and structural fragmentation characteristic of disintegrated dolomite.To address this challenge,an analysis of the applicability of the limit equilibrium method(LEM),BQ,and SSPC methods was conducted on eight disintegrated dolomite slopes located in Baoshan,Southwest China.However,conflicting results were obtained.Therefore,this paper introduces a novel method,SMRDDS,to provide rapid and accurate assessment of disintegrated dolomite slope stability.This method incorporates parameters such as disintegrated grade,joint state,groundwater conditions,and excavation methods.The findings reveal that six slopes exhibit stability,while two are considered partially unstable.Notably,the proposed method demonstrates a closer match with the actual conditions and is more time-efficient compared with the BQ and SSPC methods.However,due to the limited research on disintegrated dolomite slopes,the results of the SMRDDS method tend to be conservative as a safety precaution.In conclusion,the SMRDDS method can quickly evaluate the current situation of disintegrated dolomite slopes in the field.This contributes significantly to disaster risk reduction for disintegrated dolomite slopes.
基金supported by a Beijing Municipal Science and Technology Project (Grant No. Z171100004417008)the National Key R&D Program of China (Grant No. 2018YFF0300102)the National Natural Science Foundation of China (Grant Nos. 41375038 and 41575050)
文摘Using melting layer(ML)and non-melting layer(NML)data observed with the X-band dual linear polarization Doppler weather radar(X-POL)in Shunyi,Beijing,the reflectivity(ZH),differential reflectivity(ZDR),and correlation coefficient(CC)in the ML and NML are obtained in several stable precipitation processes.The prior probability density distributions(PDDs)of the ZH,ZDR and CC are calculated first,and then the probabilities of ZH,ZDR and CC at each radar gate are determined(PBB in the ML and PNB in the NML)by the Bayesian method.When PBB>PNB the gate belongs to the ML,and when PBB<PNB the gate belongs to the NML.The ML identification results with the Bayesian method are contrasUsing melting layer(ML)and non-melting layer(NML)data observed with the X-band dual linear polarization Doppler weather radar(X-POL)in Shunyi,Beijing,the reflectivity(ZH),differential reflectivity(ZDR),and correlation coefficient(CC)in the ML and NML are obtained in several stable precipitation processes.The prior probability density distributions(PDDs)of the ZH,ZDR and CC are calculated first,and then the probabilities of ZH,ZDR and CC at each radar gate are determined(PBB in the ML and PNB in the NML)by the Bayesian method.When PBB>PNB the gate belongs to the ML,and when PBB<PNB the gate belongs to the NML.The ML identification results with the Bayesian method are contrasted under the conditions of the independent PDDs and joint PDDs of the ZH,ZDR and CC.The results suggest that MLs can be identified effectively,although there are slight differences between the two methods.Because the values of the polarization parameters are similar in light rain and dry snow,it is difficult for the polarization radar to distinguish them.After using the Bayesian method to identify the ML,light rain and dry snow can be effectively separated with the X-POL observed data.ted under the conditions of the independent PDDs and joint PDDs of the ZH,ZDR and CC.The results suggest that MLs can be identified effectively,although there are slight differences between the two methods.Because the values of the polarization parameters are similar in light rain and dry snow,it is difficult for the polarization radar to distinguish them.After using the Bayesian method to identify the ML,light rain and dry snow can be effectively separated with the X-POL observed data.
基金supported by the National Natural Science Foundation of China(Grant No.40875012)the National Basic Research Program of China(Grant No.2009CB421502)the Meteorology Open Fund of Huaihe River Basin(HRM200704).
文摘We describe how the Unit-Feature Spatial Classification Method(UFSCM) can be used operationally to classify cloud types in satellite imagery efficiently and conveniently.By using a combination of Interactive Data Language(IDL) and Visual C++(VC) code in combination to extend the technique in three dimensions(3-D),this paper provides an efficient method to implement interactive computer visualization of the 3-D discrimination matrix modification,so as to deal with the bi-spectral limitations of traditional two dimensional(2-D) UFSCM.The case study of cloud-type classification based on FY-2C satellite data (0600 UTC 18 and 0000 UTC 10 September 2007) is conducted by comparison with ground station data, and indicates that 3-D UFSCM makes more use of the pattern recognition information in multi-spectral imagery,resulting in more reasonable results and an improvement over the 2-D method.
基金Project supported by the Joint Funds of the National Natural Science Foundation of China(Grant No.U1601213)the National Natural Science Foundation of China(Grant Nos.51601005 and 61704006)+1 种基金the Beijing Natural Science Foundation(Grant No.2182032)the Fundamental Research Funds for the Central Universities
文摘Thermoelectric materials have aroused widespread concern due to their unique ability to directly convert heat to electricity without any moving parts or noxious emissions.Taking advantages of two-dimensional structures of thermoelectric films,the potential applications of thermoelectric materials are diversified,particularly in microdevices.Well-controlled nanostructures in thermoelectric films are effective to optimize the electrical and thermal transport,which can significantly improve the performance of thermoelectric materials.In this paper,various physical and chemical approaches to fabricate thermoelectric films,including inorganic,organic,and inorganic–organic composites,are summarized,where more attentions are paid on the inorganic thermoelectric films for their excellent thermoelectric responses.Additionally,strategies for enhancing the performance of thermoelectric films are also discussed.
基金Supported by the Science Research Foundation(2010Y290) of Yunnan Department of Education
文摘As the key technology of extracting remote sensing information,the classification of remote sensing images has always been the research focus in the field of remote sensing. The paper introduces the classification process and system of remote sensing images. According to the recent research status of domestic and international remote sensing classification methods,the new study dynamics of remote sensing classification,such as artificial neural networks,support vector machine,active learning and ensemble multi-classifiers,were introduced,providing references for the automatic and intelligent development of remote sensing images classification.
基金Innovation Team Building Program of Beijing Institute of Fashion Technology,China。
文摘In recent years,smart textiles have attracted the attention of scholars from all walks of life,but there is an imbalance between functionality and usability,which affects their marketization process.Firstly,five representative smart textiles are introduced and their respective wearability is described around preparation methods.Secondly,it is concluded that the preparation methods of smart textiles can be divided into two categories:fiber methods and finishing methods.The fiber methods refer to making smart fibers into smart textiles.Textiles made by fiber methods are breathable and feel good in the hand,but the mechanical properties are influenced by the production equipment,and the process cost is high.The finishing methods refer to the functional finishing of ordinary textiles.Although the finishing method is simple and convenient,it may reduce the comfort of the textile.Finally,applications and new research in various fields of smart textiles are presented with promising prospects.It is anticipated that this review will serve as a theoretical basis for future research and development of smart textiles.Researchers are expected to create new technologies to overcome the tension between functionality and usability,as well as to increase user comfort and convenience.
文摘A New method of rock drillability classification for impregnated diamond drilling is recommended. The essence of the method is comparing the area of the slots cut respectively on a standard synthetic rock sample and the rock sample being classified by one diamond saw to determine the rock drillability in diamond core drilling. This method has the advantages of good in simulation and stable in comparison standard.
基金supported by Research Grants Council of Hong Kong under Grant No.17301214HKU CERG Grants,Fundamental Research Funds for the Central Universities+2 种基金the Research Funds of Renmin University of ChinaHung Hing Ying Physical Research Grantthe Natural Science Foundation of China under Grant No.11271144
文摘Driven by the challenge of integrating large amount of experimental data, classification technique emerges as one of the major and popular tools in computational biology and bioinformatics research. Machine learning methods, especially kernel methods with Support Vector Machines (SVMs) are very popular and effective tools. In the perspective of kernel matrix, a technique namely Eigen- matrix translation has been introduced for protein data classification. The Eigen-matrix translation strategy has a lot of nice properties which deserve more exploration. This paper investigates the major role of Eigen-matrix translation in classification. The authors propose that its importance lies in the dimension reduction of predictor attributes within the data set. This is very important when the dimension of features is huge. The authors show by numerical experiments on real biological data sets that the proposed framework is crucial and effective in improving classification accuracy. This can therefore serve as a novel perspective for future research in dimension reduction problems.
基金sponsored by National Key R&D Program of China(2018YFC1504504)Youth Foundation of Yunnan Earthquake Agency(2021K01)Project of Yunnan Earthquake Agency“Chuan bang dai”(CQ3-2021001).
文摘In order to improve the accuracy of building structure identification using remote sensing images,a building structure classification method based on multi-feature fusion of UAV remote sensing image is proposed in this paper.Three identification approaches of remote sensing images are integrated in this method:object-oriented,texture feature,and digital elevation based on DSM and DEM.So RGB threshold classification method is used to classify the identification results.The accuracy of building structure classification based on each feature and the multi-feature fusion are compared and analyzed.The results show that the building structure classification method is feasible and can accurately identify the structures in large-area remote sensing images.
文摘This paper proposes an adaptive and diverse hybrid-based ensemble method to improve the performance of binary classification. The proposed method is a non-linear combination of base models and the application of adaptive selection of the most suitable model for each data instance. Ensemble method, an important machine learning technique uses multiple single models to construct a hybrid model. A hybrid model generally performs better compared to a single individual model. In a given dataset the application of diverse single models trained with different machine learning algorithms will have different capabilities in recognizing patterns in the given training sample. The proposed approach has been validated on Repeat Buyers Prediction dataset and Census Income Prediction dataset. The experiment results indicate up to 18.5% improvement on F1 score for the Repeat Buyers dataset compared to the best individual model. This improvement also indicates that the proposed ensemble method has an exceptional ability of dealing with imbalanced datasets. In addition, the proposed method outperforms two other commonly used ensemble methods (Averaging and Stacking) in terms of improved F1 score. Finally, our results produced a slightly higher AUC score of 0.718 compared to the previous result of AUC score of 0.712 in the Repeat Buyers competition. This roughly 1% increase AUC score in performance is significant considering a very big dataset such as Repeat Buyers.
文摘This paper aims to establish a comparison between both geomagnetic activity classification methods on foF2 diurnal variation over solar cycle phases. It concerns first a comparison of geomagnetic activity occurrences according to both classification methods;and second the geomagnetic effect on foF2 diurnal variation profiles as defined for the equatorial latitudes. The occurrences of the different disturbed geomagnetic activities (recurrent activity (RA), shock activity (SA) and fluctuant activity (FA)) according to both classifications (ancient classification (AC) and new classification (NC)) have been studied at Dakar ionosonde station (Lat: 14.8°N;Long: 342.6°E). Regarding both classifications, the RA occurs more during the decreasing phase. And it’s observed that the RA occurs the most during the increasing phase for the AC and during the minimum phase for the NC. The maximum gap of occurrence (<img src="Edit_e4627ea9-9a9a-4473-9017-202d04a16377.bmp" alt="" /><span><span style="font-family:Verdana;">) between both classifications is <span style="font-size:10.0pt;font-family:;" "=""><span style="font-family:Verdana, Helvetica, Arial;white-space:normal;background-color:#FFFFFF;">-</span></span></span><span style="font-family:;" "=""><span style="font-family:Verdana;">11.1%</span><span style="font-family:Verdana;"> (for the negative value which is observed during the increasing phase) and </span><span style="font-family:Verdana;">+16.74%</span><span style="font-family:Verdana;"> (for the positive one which is observed during the decreasing phase). The occurrence of the SA in relation with both classifications is the lowest during the minimum phase and the maximum occurrence is observed during the maximum and decreasing phases, for the AC, with a value close to </span><span style="font-family:Verdana;">37%</span><span style="font-family:Verdana;"> and for the NC at the maximum phase with a percentage of </span><span style="font-family:Verdana;">54.47%</span><span><span style="font-family:Verdana;">. The maximum gap of occurrence (</span><img src="Edit_20fa141b-ecee-4e06-8024-144ba0969395.bmp" alt="" /></span></span><span style="font-family:Verdana;">) between both classifications is <span style="font-size:10.0pt;font-family:;" "=""><span style="font-family:Verdana, Helvetica, Arial;white-space:normal;background-color:#FFFFFF;">-</span></span></span><span style="font-family:;" "=""><span style="font-family:Verdana;">17.85%</span><span style="font-family:Verdana;"> (for the negative value which is observed at maximum phase) and </span><span style="font-family:Verdana;">+13.53%</span><span style="font-family:Verdana;"> (for the positive one which is observed during the decreasing phase). For both classifications, the FA occurs the least during the minimum phase and the most during the maximum phase for the AC and at maximum and decreasing phases with percentage values of occurrence of roughly </span><span style="font-family:Verdana;">37%</span><span><span style="font-family:Verdana;"> for the NC. The maximum gap of occurrence (</span><img src="Edit_eecb8939-783e-4d43-b92c-80c528c1890b.bmp" alt="" /><span style="font-family:Verdana;"></span></span></span><span style="font-family:Verdana;">) between both classifications is <span style="font-size:10.0pt;font-family:;" "=""><span style="font-family:Verdana, Helvetica, Arial;white-space:normal;background-color:#FFFFFF;">-</span></span>10% (for the negative value which is observed during the decreasing phase) and </span><span style="font-family:;" "=""><span style="font-family:Verdana;">+20.11%</span><span style="font-family:Verdana;"> (for the positive one which is observed during the maximum phase). foF2 diurnal profiles throughout solar cycle phases concerning the AC and the NC have been compared. The FA diurnal profiles don’t present a difference. The RA and the SA present a difference during minimum and increasing phases and the least at maximum and decreasing phases.</span></span></span>
基金National Natural Science Foundation of China(No.61862048)。
文摘Lie algorithm combined with differential form Wu's method is used to complete the symmetry classification of partial differential equations(PDEs)containing arbitrary parameter.This process can be reduced to solve a large system of determining equations,which seems rather difficult to solve,then the differential form Wu's method is used to decompose the determining equations into a series of equations,which are easy to solve.To illustrate the usefulness of this method,we apply it to some test problems,and the results show the performance of the present work.
文摘The classification of thematic mapper imagery in areas with strong topographic variations has proven problematic in the past using a single classifier, due to the changing sun illumination geometry. This often results in the phenomena of identical object with dissimilar spectrum and different objects with similar spectrum. In this paper, an integrated classification method that combines a decision tree with slope data, tasseled cap transformation indices and maximum likelihood classifier is introduced, to find an optimal classification method for thematic mapper imagery of plain and highland terrains. A Landsat 7 ETM+ image acquired over Hangzhou Bay, in eastern China was used to test the method. The results indicate that the performance of the inte- grated classifier is acceptably good in comparison with that of the existing most widely used maximum likelihood classifier. The integrated classifier depends on hypsography (variation in topography) and the characteristics of ground truth objects (plant and soil). It can greatly reduce the influence of the homogeneous spectrum caused by topographic variation. This integrated classifier might potentially be one of the most accurate classifiers and valuable tool for land cover and land use mapping of plain and highland terrains.
基金supported by the Natural Sci-ence Foundation of Jiangsu Province (Grant No. BK2005040)the MOHURD Program of China (Grant No. 06-R5-10).
文摘Regional agriculture is the basis of regional sustainable development,so sustainable regional agricul-tural development is essential to the sustainable development of the whole society and becomes the focus of global research.The classifi cation of regional agricultural structure is the basic work of regional agriculture study.This paper constructs index system(27 indices) of regional agricultural structure types with the three big indices:natural resources,developmental level of the agro-economy,and agro-ecological conditions.This paper also endows weight to every sub-classif ication index by means of AHP and obtains the comprehensive evaluation value of the three types of indices with arithmetic average weight approach.The regional agricultural structure can be classif ied into eight types in accordance with this evaluation results.The empirical study of China shows that the 31 provinces(munici-palities and autonomous regions) are of different agriculture structural types.Finally,countermeasures of sustain-able agricultural development are put forward for the different agriculture structure features.
基金financial support provided by the Major Project of Yunnan Science and Technology,under Project No.202302AE09002003,entitled“Research on the Integration of Key Technologies in Smart Agriculture.”。
文摘This study proposed a weighted sampling hierarchical classification learning method based on an efficient backbone network model to address the problems of high costs,low accuracy,and time-consuming traditional tea disease recognition methods.This method enhances the feature extraction ability by conducting hierarchical classification learning based on the EfficientNet model,effectively alleviating the impact of high similarity between tea diseases on the model’s classification performance.To better solve the problem of few and unevenly distributed tea disease samples,this study introduced a weighted sampling scheme to optimize data processing,which not only alleviates the overfitting effect caused by too few sample data but also balances the probability of extracting imbalanced classification data.The experimental results show that the proposed method was significant in identifying both healthy tea leaves and four common leaf diseases of tea(tea algal spot disease,tea white spot disease,tea anthracnose disease,and tea leaf blight disease).After applying the“weighted sampling hierarchical classification learning method”to train 7 different efficient backbone networks,most of their accuracies have improved.The EfficientNet-B1 model proposed in this study achieved an accuracy rate of 99.21%after adopting this learning method,which is higher than EfficientNet-b2(98.82%)and MobileNet-V3(98.43%).In addition,to better apply the results of identifying tea diseases,this study developed a mini-program that operates on WeChat.Users can quickly obtain accurate identification results and corresponding disease descriptions and prevention methods through simple operations.This intelligent tool for identifying tea diseases can serve as an auxiliary tool for farmers,consumers,and related scientific researchers and has certain practical value.
文摘Engineering rock mass classification,based on empirical relations between rock mass parameters and engineering applications,is commonly used in rock engineering and forms the basis for designing rock structures.The basic data required may be obtained from visual observation and laboratory or field tests.However,owing to the discontinuous and variable nature of rock masses,it is difficult for rock engineers to directly obtain the specific design parameters needed.As an alternative,the use of geophysical methods in geomechanics such as seismography may largely address this problem.In this study,25 seismic profiles with the total length of 543 m have been scanned to determine the geomechanical properties of the rock mass in blocks Ⅰ,Ⅲ and Ⅳ-2 of the Choghart iron mine.Moreover,rock joint measurements and sampling for laboratory tests were conducted.The results show that the rock mass rating(RMR) and Q values have a close relation with P-wave velocity parameters,including P-wave velocity in field(V;).P-wave velocity in the laboratory(V;) and the ratio of V;V;(i.e.K;= V;/V;.However,Q value,totally,has greater correlation coefficient and less error than the RMR,In addition,rock mass parameters including rock quality designation(RQD),uniaxial compressive strength(UCS),joint roughness coefficient(JRC) and Schmidt number(RN) show close relationship with P-wave velocity.An equation based on these parameters was obtained to estimate the P-wave velocity in the rock mass with a correlation coefficient of 91%.The velocities in two orthogonal directions and the results of joint study show that the wave velocity anisotropy in rock mass may be used as an efficient tool to assess the strong and weak directions in rock mass.
基金This research was jointly supported by the National Natural Science Foundation of China(Grant No.42005037)the Liaoning Provincial Natural Science Foundation Project(PhD Start-up Research Fund 2019-BS-214),the Special Scientific Research Project for the Forecaster(Grant No.CMAYBY2018-018)+2 种基金a Key Technical Project of Liaoning Meteorological Bureau(Grant No.LNGJ201903)the National Key Research and Development Project(Grant No.2018YFC1505601)the Open Foundation Project of the Institute of Atmospheric Environment,China Meteorological Administration(Grant Nos.2020SYIAE08 and 2020SYIAEZD5).
文摘The classification of the Northeast China Cold Vortex(NCCV)activity paths is an important way to analyze its characteristics in detail.Based on the daily precipitation data of the northeastern China(NEC)region,and the atmospheric circulation field and temperature field data of ERA-Interim for every six hours,the NCCV processes during the early summer(June)seasons from 1979 to 2018 were objectively identified.Then,the NCCV processes were classified using a machine learning method(k-means)according to the characteristic parameters of the activity path information.The rationality of the classification results was verified from two aspects,as follows:(1)the atmospheric circulation configuration of the NCCV on various paths;and(2)its influences on the climate conditions in the NEC.The obtained results showed that the activity paths of the NCCV could be divided into four types according to such characteristics as the generation origin,movement direction,and movement velocity of the NCCV.These included the generation-eastward movement type in the east of the Mongolia Plateau(eastward movement type or type A);generation-southeast longdistance movement type in the upstream of the Lena River(southeast long-distance movement type or type B);generationeastward less-movement type near Lake Baikal(eastward less-movement type or type C);and the generation-southward less-movement type in eastern Siberia(southward less-movement type or type D).There were obvious differences observed in the atmospheric circulation configuration and the climate impact of the NCCV on the four above-mentioned types of paths,which indicated that the classification results were reasonable.