Future inter-satellite clock comparison on high orbit will require optical time and frequency transmission technology between moving objects.Here,we demonstrate robust optical frequency transmission under the conditio...Future inter-satellite clock comparison on high orbit will require optical time and frequency transmission technology between moving objects.Here,we demonstrate robust optical frequency transmission under the condition of variable link distance.This variable link is accomplished by the relative motion of a single telescope fixed on the experimental platform to a corner-cube reflector(CCR)installed on a sliding guide.Two acousto–optic modulators with different frequencies are used to separate forward signal from backward signal.With active phase noise suppression,when the CCR moves back and forth at a constant velocity of 20 cm/s and an acceleration of 20 cm/s^(2),we achieve the best frequency stability of 1.9×10^(-16) at 1 s and 7.9×10^(-19) at 1000 s indoors.This work paves the way for future studying optical frequency transfer between ultra-high-orbit satellites.展开更多
Variable frequency,a new pattern of pulse hydraulic fracturing,is presented for improving permeability in coal seam.A variable frequency pulse hydraulic fracturing testing system was built,the mould with triaxial load...Variable frequency,a new pattern of pulse hydraulic fracturing,is presented for improving permeability in coal seam.A variable frequency pulse hydraulic fracturing testing system was built,the mould with triaxial loading was developed.Based on the monitor methods of pressure sensor and acoustic emission,the trials of two patterns of pulse hydraulic fracturing of single frequency and variable frequency were carried out,and at last fracturing mechanism was analyzed.The results show that the effect of variable frequency on fracture extension is better than that of single frequency based on the analysis of macroscopic figures and AE.And the shortage of single frequency is somewhat remedied when the frequency is variable.Under variable frequency,the pressure process can be divided into three stages:low frequency band,pressure stability band and high frequency band,and rupture pressure of the sample is smaller than that of the condition of single frequency.Based on the Miner fatigue theory,the effect of different loading sequences on sample rupture is discussed and the results show that it is better to select the sequence of low frequency at first and then high frequency.Our achievements can give a basis for the improvement and optimization of the pulse hydraulic fracturing technology.展开更多
Aiming at the cropping operations widely applied in practical industry production, a new method of bar cropping is presented. The rotational speeds of actuating motor of eccentric blocks are controlled by a frequency-...Aiming at the cropping operations widely applied in practical industry production, a new method of bar cropping is presented. The rotational speeds of actuating motor of eccentric blocks are controlled by a frequency-changer, and the shearing die provides the bar with the controllable force, frequency and amplitude of vibration. By utilizing the stress concentration at the bottom of V shape groove on the bar, the low stress bar cropping is realized. The bar cropping experiments of duralumin alloy and steel show that the shear surface has no radial distortion and deviation angle, the cutting force is lower and the die life is longer compared with the common bar cropping method. According to the special feature of cutting surface obtained by the new method, a new method of measurement is proposed and applied to assess the cutting surfaces obtained by the different control curves of frequency. The results show that the linear decrease control method is the best.展开更多
Switch mode power supply (SMPS) is good selection for power supplies of Unmanned Aerial Vehicle (UAV), which is one of the most important interference sources of UAV. The power switches with their high dv/dt and di/dt...Switch mode power supply (SMPS) is good selection for power supplies of Unmanned Aerial Vehicle (UAV), which is one of the most important interference sources of UAV. The power switches with their high dv/dt and di/dt switching slopes are the sources of electromagnetic interference (EMI). In this paper, a variable frequency modulation technology of the forward converter of UAV is presented, which is utilized in SMPS to improve electromagnetic compatibility (EMC). In variable-frequency techniques, power (signal) is transmitted in power converter in wide-band mode in several frequencies that are constantly changing, the EMI spectral performance of the SMPS can be controlled with the modulating pattern and modulation method. The validity of the models and analyses are confirmed experimentally by using a dc/dc forward converter.展开更多
The nonlinear dynamical variation equation and compatible equation of the shallow conical shell with variable thickness are obtained by the theory of nonlinear dynamical variation equation and compatible equation of t...The nonlinear dynamical variation equation and compatible equation of the shallow conical shell with variable thickness are obtained by the theory of nonlinear dynamical variation equation and compatible equation of the circular thin plate with variable thickness. Assuming the thin film tension is composed of two items. The compatible equation is transformed into two independent equations. Selecting the maximum amplitude in the center of the shallow conical shells with variable thickness as the perturbation parameter, the variation equation and the differential equation are transformed into linear expression by theory of perturbation variation method. The nonlinear natural frequency of shallow conical shells with circular bottom and variable thickness under the fixed boundary conditions is solved. In the first approximate equation, the linear natural frequency of shallow conical shells with variable thickness is obtained. In the third approximate equation, the nonlinear natural frequency of it is obtained. The figures of the characteristic curves of the natural frequency varying with stationary loads, large amplitude, and variable thickness coefficient are plotted. A valuable reference is given for dynamic engineering.展开更多
To further research the response of the tearing mode(TM) to dynamic resonant magnetic perturbation(DRMP) on the J-TEXT tokamak, a modified series resonant inverter power supply(MSRIPS) with a function of discret...To further research the response of the tearing mode(TM) to dynamic resonant magnetic perturbation(DRMP) on the J-TEXT tokamak, a modified series resonant inverter power supply(MSRIPS) with a function of discrete variable frequency is designed for DRMP coils in this study. The MSRIPS is an AC–DC–AC converter, including a phase-controlled rectifier, an LC filter, an insulated gate bipolar transistor(IGBT) full bridge, a matching transformer, three resonant capacitors with different capacitance values, and three corresponding silicon controlled rectifier(SCR) switches. The function of discrete variable frequency is realized by switching over different resonant capacitors with corresponding SCR switches while matching the corresponding driving frequency of the IGBT full bridge. A detailed switching strategy of the SCR switch is put forward to obtain sinusoidal current waveform and realize current waveform smooth transition during frequency conversion. In addition, a resistor and thyristor bleeder is designed to protect the SCR switch from overvoltage. Manufacturing of the MSRIPS is completed, and the MSRIPS equipment can output current with an amplitude of 1.5 kA when its working frequency jumps among different frequencies. Moreover, the current waveform is sinusoidal and can smoothly transition during frequency conversion. Furthermore, the transition time when the current amplitude rises from zero to a steady state is less than 2 ms during frequency conversion. By using the MSRIPS, the expected discrete variable frequency DRMP is generated, and the phenomenon of the TM being locked to the discrete variable frequency DRMP is observed on the J-TEXT tokamak.展开更多
A new type of variable polarity welding power modulated with high-frequency pulse current is developed. Series of high-frequency pulse current is superimposed on direct-current-electrode-negative (DCEN), which can i...A new type of variable polarity welding power modulated with high-frequency pulse current is developed. Series of high-frequency pulse current is superimposed on direct-current-electrode-negative (DCEN), which can improve the crystallization process in the weld bead as a result of the electromagnetic force generated by pulse current. Digital signal processor (DSP) is used to realize the closed-loop control of the first inverter, variable polarity output of the second inverter and high-frequency pulse current superposition.展开更多
The paper presents a reliability evaluation method based on fault tree analysis with set theory and minimal cut set as core algorithm, which can be used to evaluate the reliability for industrial grids with wide appli...The paper presents a reliability evaluation method based on fault tree analysis with set theory and minimal cut set as core algorithm, which can be used to evaluate the reliability for industrial grids with wide application of variable frequency drives. The working principle is introduced firstly, based on which the method development considering different system topology designs, backup solutions and redundancy mechanisms are analyzed in details. In the end the proposed method is applied to two cases to show the reliability performance of system with variable frequency drives. The proposed method is also suitable for analyzing the reliability performance of industrial grids with other types of power electronic converter technology.展开更多
Hybrid ultrahigh frequency pulse variable polarity gas tungsten arc welding (HPVP-GTAW) for 2A14-T6 high strength aluminum alloy was carried out and the effects of variable polarity frequency with constant pulse cur...Hybrid ultrahigh frequency pulse variable polarity gas tungsten arc welding (HPVP-GTAW) for 2A14-T6 high strength aluminum alloy was carried out and the effects of variable polarity frequency with constant pulse current frequency 40 kHz on weld bead geometry, microstrueture and microhardness were analyzed. Experimental results indicate that, compared to that of the conventional VP-GTAW process, the weld depth and ratio of weld depth to width are improved significantly by the variable polarity frequency in the HPVP-GTAW process, which the ratio of weld depth to width is improved by 36% at equal variable polarity frequency of 100 Hz, and improved by 55% with that of 200 Hz. Weld microstructure and microhardness distribution are changed obviously with the increase of variable polarity frequency. In the conventional VP-GTA W process, the grains in weld central zone are coarser, and the microhardness in weld central zone and fusion zone is about 95 HV and the lowest 82 HV, respectively. The microhardness is enhanced to a certain extent both in the weld central zone and fusion zone with the variation of variable polarity frequency in the HPVP-GTAW process due to the refinement and uniformity of weld microstructure. With the variable polarity frequency of 600 Hz, the microhardness in weld central zone and fusion zone reaches nearly 110 HV and 97 HV, respectively.展开更多
Based on the characteristic of AC-excited variable speed constant frequency(VSCF)wind power generation,the vector control technique was applied in a doubly fed induction generator(DFIG).Maximum wind energy or maximum ...Based on the characteristic of AC-excited variable speed constant frequency(VSCF)wind power generation,the vector control technique was applied in a doubly fed induction generator(DFIG).Maximum wind energy or maximum output power point can be tracked by decoupling control of active power and reactive power.The research result shows that the net power of generation system delivered to grid in maximum wind energy tracking mode is not the most.We presented a novel maximum power point tracking(MPPT)control strategy by analyzing the DFIG mathematic model and power relations which delivered the maximum power to the grid.The maximum power point could be tracked automatically without measuring wind speed in the control strategy and the control was independent of optimal turbine power curve,which had excellent dynamic and static performances and robustness.Simulation and experimental results testify the accuracy and validity of the control strategy.展开更多
in this paper, an electromechanically coupled mathematic model of multi-roller driving system for belt conveyor is set up, and the computing equations for dynamic displacement and dynamic tension of the conveyor are a...in this paper, an electromechanically coupled mathematic model of multi-roller driving system for belt conveyor is set up, and the computing equations for dynamic displacement and dynamic tension of the conveyor are also formulated when the hoister is used for straining. Based on the belt conveyor of main inclined shaft in Chengzhuang coal mine, the driving torque, driving power and starting-speed characteristic of each electric motor are studied and measured when multi-roller variable-frequency drive (power distribution 2∶1) is used. The optimal control and the optimal starting-acceleration of the multi-roller variable-frequency drive are determined by a large number of industrial experiments and theoretical calculations.展开更多
In cascaded H-bridge multilevel inverter, a variable frequency inverted sine PWM technique is modeled for hybrid electric vehicles. It has a particular advantage of increasing power which is achieved using series conn...In cascaded H-bridge multilevel inverter, a variable frequency inverted sine PWM technique is modeled for hybrid electric vehicles. It has a particular advantage of increasing power which is achieved using series connection of H-bridge and also this topology is capable to produce superior spectral quality with considerable improvement of fundamental voltage. The variable frequency inverted sine PWM technique produces lesser torque ripple and enhances the fundamental output voltage mainly at lower modulation index ranges. The topologies of multilevel inverter are flying capacitor, diode clamped and cascaded inverter. In the paper, we will discuss about the cascaded multilevel inverter based on inverted sine PWM technique. The two switching strategies widely used to control multilevel inverters are constant frequency inverted sine PWM (CF-ISPWM) and variable frequency inverted sine PWM (VF-ISPWM). This implies that switch utilization substantially reduces 32.35% of the constant frequency inverted sine PWM switching technique. The performance of the technique is validated in terms of Total Harmonic Distortion (THD) and Torque ripple which significantly reduces when compared to constant frequency ISPWM. The analysis of conventional triangular PWM inverter and inverted sine PWM inverter using constant and variable switching scheme is done in MATLAB Simulink and verified experimentally by FPGA Spartan 3E processor.展开更多
Asymmetric three-phase cascading Trinary-DC source Multilevel Inverter which can achieve reduced harmonics and superior root mean square (RMS) values of the output voltage is proposed. This topology can achieve cascad...Asymmetric three-phase cascading Trinary-DC source Multilevel Inverter which can achieve reduced harmonics and superior root mean square (RMS) values of the output voltage is proposed. This topology can achieve cascaded full bridge inverter operation with dissimilar (unequal) DC Source and it is fired by using variable frequency pulse with modulation technique as a switching strategy. This pulse width modulation switching strategy has a newly adopted multicarrier single reference technique. The performance parameter factors like Form Factor (FF), Crest Factor (CF), Total Harmonic Distortion (THD) and fundamental RMS output voltage (V<sub>RMS</sub>) are estimated by using proposed asymmetrical three-phase cascading multilevel inverter for several modulation indices (0.8 - 1). The research study carries with MATLAB/SIMULINK based simulation and experimental results obtained using appropriate prototype (test board) to prove the viability of the proposed concept.展开更多
In the paper, the method to optimize the rotor structure in variable frequency speed control motors is introduced. The saturation and the skin effect are considered and 2D no-load and load electromagnetic field is cal...In the paper, the method to optimize the rotor structure in variable frequency speed control motors is introduced. The saturation and the skin effect are considered and 2D no-load and load electromagnetic field is calculated in finite elements for a variable frequency speed control motor before and after optimization. Finally, no-load current and operation performance before and after optimization are obtained and the two results are contrasted.展开更多
The invariant, propagator, and wavefunction for a variable frequency harmonic oscillator in an electro-magnetic field are obtained by making a specific coordinate transformation and by using the method of phase spacep...The invariant, propagator, and wavefunction for a variable frequency harmonic oscillator in an electro-magnetic field are obtained by making a specific coordinate transformation and by using the method of phase spacepath integral method. The probability amplitudes for a dissipative harmonic oscillator in the time varying electric fieldE(t) = Eo sin(Ωt) are obtained.展开更多
In general,Variable-Speed Constant Frequency (VSCF)Wind generation system is controlled by stator voltage orientation method which based on the mathematic model of VSCF Wind generation system and discussed the control...In general,Variable-Speed Constant Frequency (VSCF)Wind generation system is controlled by stator voltage orientation method which based on the mathematic model of VSCF Wind generation system and discussed the control strategy.Present the whole dynamic control model of variable-speed wind generator system in MATLAB/ Simulink,and the simulation results confirm the validity and effectiveness of the proposed control strategy.展开更多
基金Project supported by the National Key Research and Development Program of China(Grant No.2020YFB0408300)the National Natural Science Foundation of China(Grant No.62175246)+2 种基金the Natural Science Foundation of Shanghai,China(Grant No.22ZR1471100)the Youth Innovation Promotion Association of Chinese Academy of Sciences(Grant No.YIPA2021244)the Innovation Program for Quantum Science and Technology(Grant No.2021ZD0300701).
文摘Future inter-satellite clock comparison on high orbit will require optical time and frequency transmission technology between moving objects.Here,we demonstrate robust optical frequency transmission under the condition of variable link distance.This variable link is accomplished by the relative motion of a single telescope fixed on the experimental platform to a corner-cube reflector(CCR)installed on a sliding guide.Two acousto–optic modulators with different frequencies are used to separate forward signal from backward signal.With active phase noise suppression,when the CCR moves back and forth at a constant velocity of 20 cm/s and an acceleration of 20 cm/s^(2),we achieve the best frequency stability of 1.9×10^(-16) at 1 s and 7.9×10^(-19) at 1000 s indoors.This work paves the way for future studying optical frequency transfer between ultra-high-orbit satellites.
基金Financial support for this work,provided by the National Basic Research Program of China(No.2011CB201205)the Natural Science Foundation of Jiangsu Province(No.BK2012571)+1 种基金the Program for New Century Excellent Talents in University(No.NCET-120959)the"Qing-Lan Project"and Collegial Graduate Research and Innovation Program of Jiangsu Province(No.CXZZ13_0955)
文摘Variable frequency,a new pattern of pulse hydraulic fracturing,is presented for improving permeability in coal seam.A variable frequency pulse hydraulic fracturing testing system was built,the mould with triaxial loading was developed.Based on the monitor methods of pressure sensor and acoustic emission,the trials of two patterns of pulse hydraulic fracturing of single frequency and variable frequency were carried out,and at last fracturing mechanism was analyzed.The results show that the effect of variable frequency on fracture extension is better than that of single frequency based on the analysis of macroscopic figures and AE.And the shortage of single frequency is somewhat remedied when the frequency is variable.Under variable frequency,the pressure process can be divided into three stages:low frequency band,pressure stability band and high frequency band,and rupture pressure of the sample is smaller than that of the condition of single frequency.Based on the Miner fatigue theory,the effect of different loading sequences on sample rupture is discussed and the results show that it is better to select the sequence of low frequency at first and then high frequency.Our achievements can give a basis for the improvement and optimization of the pulse hydraulic fracturing technology.
基金This workis supported by the National Natural Science Foundation of China (No50375117)
文摘Aiming at the cropping operations widely applied in practical industry production, a new method of bar cropping is presented. The rotational speeds of actuating motor of eccentric blocks are controlled by a frequency-changer, and the shearing die provides the bar with the controllable force, frequency and amplitude of vibration. By utilizing the stress concentration at the bottom of V shape groove on the bar, the low stress bar cropping is realized. The bar cropping experiments of duralumin alloy and steel show that the shear surface has no radial distortion and deviation angle, the cutting force is lower and the die life is longer compared with the common bar cropping method. According to the special feature of cutting surface obtained by the new method, a new method of measurement is proposed and applied to assess the cutting surfaces obtained by the different control curves of frequency. The results show that the linear decrease control method is the best.
文摘Switch mode power supply (SMPS) is good selection for power supplies of Unmanned Aerial Vehicle (UAV), which is one of the most important interference sources of UAV. The power switches with their high dv/dt and di/dt switching slopes are the sources of electromagnetic interference (EMI). In this paper, a variable frequency modulation technology of the forward converter of UAV is presented, which is utilized in SMPS to improve electromagnetic compatibility (EMC). In variable-frequency techniques, power (signal) is transmitted in power converter in wide-band mode in several frequencies that are constantly changing, the EMI spectral performance of the SMPS can be controlled with the modulating pattern and modulation method. The validity of the models and analyses are confirmed experimentally by using a dc/dc forward converter.
文摘The nonlinear dynamical variation equation and compatible equation of the shallow conical shell with variable thickness are obtained by the theory of nonlinear dynamical variation equation and compatible equation of the circular thin plate with variable thickness. Assuming the thin film tension is composed of two items. The compatible equation is transformed into two independent equations. Selecting the maximum amplitude in the center of the shallow conical shells with variable thickness as the perturbation parameter, the variation equation and the differential equation are transformed into linear expression by theory of perturbation variation method. The nonlinear natural frequency of shallow conical shells with circular bottom and variable thickness under the fixed boundary conditions is solved. In the first approximate equation, the linear natural frequency of shallow conical shells with variable thickness is obtained. In the third approximate equation, the nonlinear natural frequency of it is obtained. The figures of the characteristic curves of the natural frequency varying with stationary loads, large amplitude, and variable thickness coefficient are plotted. A valuable reference is given for dynamic engineering.
基金supported by the National ITER Project Foundation of China(No.2014GB118000)National Natural Science Foundation of China(No.11405068)
文摘To further research the response of the tearing mode(TM) to dynamic resonant magnetic perturbation(DRMP) on the J-TEXT tokamak, a modified series resonant inverter power supply(MSRIPS) with a function of discrete variable frequency is designed for DRMP coils in this study. The MSRIPS is an AC–DC–AC converter, including a phase-controlled rectifier, an LC filter, an insulated gate bipolar transistor(IGBT) full bridge, a matching transformer, three resonant capacitors with different capacitance values, and three corresponding silicon controlled rectifier(SCR) switches. The function of discrete variable frequency is realized by switching over different resonant capacitors with corresponding SCR switches while matching the corresponding driving frequency of the IGBT full bridge. A detailed switching strategy of the SCR switch is put forward to obtain sinusoidal current waveform and realize current waveform smooth transition during frequency conversion. In addition, a resistor and thyristor bleeder is designed to protect the SCR switch from overvoltage. Manufacturing of the MSRIPS is completed, and the MSRIPS equipment can output current with an amplitude of 1.5 kA when its working frequency jumps among different frequencies. Moreover, the current waveform is sinusoidal and can smoothly transition during frequency conversion. Furthermore, the transition time when the current amplitude rises from zero to a steady state is less than 2 ms during frequency conversion. By using the MSRIPS, the expected discrete variable frequency DRMP is generated, and the phenomenon of the TM being locked to the discrete variable frequency DRMP is observed on the J-TEXT tokamak.
文摘A new type of variable polarity welding power modulated with high-frequency pulse current is developed. Series of high-frequency pulse current is superimposed on direct-current-electrode-negative (DCEN), which can improve the crystallization process in the weld bead as a result of the electromagnetic force generated by pulse current. Digital signal processor (DSP) is used to realize the closed-loop control of the first inverter, variable polarity output of the second inverter and high-frequency pulse current superposition.
文摘The paper presents a reliability evaluation method based on fault tree analysis with set theory and minimal cut set as core algorithm, which can be used to evaluate the reliability for industrial grids with wide application of variable frequency drives. The working principle is introduced firstly, based on which the method development considering different system topology designs, backup solutions and redundancy mechanisms are analyzed in details. In the end the proposed method is applied to two cases to show the reliability performance of system with variable frequency drives. The proposed method is also suitable for analyzing the reliability performance of industrial grids with other types of power electronic converter technology.
基金This work is supported by the National Natural Science Foundation of China (Grant No. 51005011 ) and the Fundamental Research Funds for the Central Universities ( YWF-12-LGJC-001 ).
文摘Hybrid ultrahigh frequency pulse variable polarity gas tungsten arc welding (HPVP-GTAW) for 2A14-T6 high strength aluminum alloy was carried out and the effects of variable polarity frequency with constant pulse current frequency 40 kHz on weld bead geometry, microstrueture and microhardness were analyzed. Experimental results indicate that, compared to that of the conventional VP-GTAW process, the weld depth and ratio of weld depth to width are improved significantly by the variable polarity frequency in the HPVP-GTAW process, which the ratio of weld depth to width is improved by 36% at equal variable polarity frequency of 100 Hz, and improved by 55% with that of 200 Hz. Weld microstructure and microhardness distribution are changed obviously with the increase of variable polarity frequency. In the conventional VP-GTA W process, the grains in weld central zone are coarser, and the microhardness in weld central zone and fusion zone is about 95 HV and the lowest 82 HV, respectively. The microhardness is enhanced to a certain extent both in the weld central zone and fusion zone with the variation of variable polarity frequency in the HPVP-GTAW process due to the refinement and uniformity of weld microstructure. With the variable polarity frequency of 600 Hz, the microhardness in weld central zone and fusion zone reaches nearly 110 HV and 97 HV, respectively.
基金Funded by the National Natural Science Foundation of China(No.60974049)the Science and Technology Support Industrial Project of Jiangsu Province(No.BZ2008031,No.BE2008074,and No.BE2009090)+1 种基金the Nantong International Cooperative Project(No.W2009003)the Natural Science Foundation of Nantong University(No.08Z022 and No.08Z025).
文摘Based on the characteristic of AC-excited variable speed constant frequency(VSCF)wind power generation,the vector control technique was applied in a doubly fed induction generator(DFIG).Maximum wind energy or maximum output power point can be tracked by decoupling control of active power and reactive power.The research result shows that the net power of generation system delivered to grid in maximum wind energy tracking mode is not the most.We presented a novel maximum power point tracking(MPPT)control strategy by analyzing the DFIG mathematic model and power relations which delivered the maximum power to the grid.The maximum power point could be tracked automatically without measuring wind speed in the control strategy and the control was independent of optimal turbine power curve,which had excellent dynamic and static performances and robustness.Simulation and experimental results testify the accuracy and validity of the control strategy.
文摘in this paper, an electromechanically coupled mathematic model of multi-roller driving system for belt conveyor is set up, and the computing equations for dynamic displacement and dynamic tension of the conveyor are also formulated when the hoister is used for straining. Based on the belt conveyor of main inclined shaft in Chengzhuang coal mine, the driving torque, driving power and starting-speed characteristic of each electric motor are studied and measured when multi-roller variable-frequency drive (power distribution 2∶1) is used. The optimal control and the optimal starting-acceleration of the multi-roller variable-frequency drive are determined by a large number of industrial experiments and theoretical calculations.
文摘In cascaded H-bridge multilevel inverter, a variable frequency inverted sine PWM technique is modeled for hybrid electric vehicles. It has a particular advantage of increasing power which is achieved using series connection of H-bridge and also this topology is capable to produce superior spectral quality with considerable improvement of fundamental voltage. The variable frequency inverted sine PWM technique produces lesser torque ripple and enhances the fundamental output voltage mainly at lower modulation index ranges. The topologies of multilevel inverter are flying capacitor, diode clamped and cascaded inverter. In the paper, we will discuss about the cascaded multilevel inverter based on inverted sine PWM technique. The two switching strategies widely used to control multilevel inverters are constant frequency inverted sine PWM (CF-ISPWM) and variable frequency inverted sine PWM (VF-ISPWM). This implies that switch utilization substantially reduces 32.35% of the constant frequency inverted sine PWM switching technique. The performance of the technique is validated in terms of Total Harmonic Distortion (THD) and Torque ripple which significantly reduces when compared to constant frequency ISPWM. The analysis of conventional triangular PWM inverter and inverted sine PWM inverter using constant and variable switching scheme is done in MATLAB Simulink and verified experimentally by FPGA Spartan 3E processor.
文摘Asymmetric three-phase cascading Trinary-DC source Multilevel Inverter which can achieve reduced harmonics and superior root mean square (RMS) values of the output voltage is proposed. This topology can achieve cascaded full bridge inverter operation with dissimilar (unequal) DC Source and it is fired by using variable frequency pulse with modulation technique as a switching strategy. This pulse width modulation switching strategy has a newly adopted multicarrier single reference technique. The performance parameter factors like Form Factor (FF), Crest Factor (CF), Total Harmonic Distortion (THD) and fundamental RMS output voltage (V<sub>RMS</sub>) are estimated by using proposed asymmetrical three-phase cascading multilevel inverter for several modulation indices (0.8 - 1). The research study carries with MATLAB/SIMULINK based simulation and experimental results obtained using appropriate prototype (test board) to prove the viability of the proposed concept.
文摘In the paper, the method to optimize the rotor structure in variable frequency speed control motors is introduced. The saturation and the skin effect are considered and 2D no-load and load electromagnetic field is calculated in finite elements for a variable frequency speed control motor before and after optimization. Finally, no-load current and operation performance before and after optimization are obtained and the two results are contrasted.
文摘The invariant, propagator, and wavefunction for a variable frequency harmonic oscillator in an electro-magnetic field are obtained by making a specific coordinate transformation and by using the method of phase spacepath integral method. The probability amplitudes for a dissipative harmonic oscillator in the time varying electric fieldE(t) = Eo sin(Ωt) are obtained.
文摘In general,Variable-Speed Constant Frequency (VSCF)Wind generation system is controlled by stator voltage orientation method which based on the mathematic model of VSCF Wind generation system and discussed the control strategy.Present the whole dynamic control model of variable-speed wind generator system in MATLAB/ Simulink,and the simulation results confirm the validity and effectiveness of the proposed control strategy.